2019 Ford Flex
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2019 Ford Flex. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2019 Ford Flex. Newest first.
Ford Motor Company (Ford) is recalling certain 2017-2019 Flex vehicles. The driver and front passenger B-Pillar door trim may detach while driving.
Risk and remedy
Risk
Door trim that detaches while driving can create a road hazard, increasing the risk of a crash.
Remedy
Dealers will repair or replace the B-pillar trim as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed December 17, 2025. Additional letters will be sent once the remedy is available, anticipated March 2027. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB8. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 28, 2025.
Ford Motor Company (Ford) is recalling certain 2015-2019 Flex, 2015 Explorer, Lincoln MKT, Lincoln MKZ, 2015-2016 C-Max, Escape, Taurus, 2016 Fusion, 2018-2019 Taurus, 2019 Lincoln MKT, Fiesta, and 2020 Mustang vehicles. The rearview camera may display a distorted, intermittent, or blank image when the vehicle is in reverse.
Risk and remedy
Risk
A rearview camera that fails to properly display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy
Dealers will inspect and replace the rearview camera as necessary, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on October 25, 2025. Additional letters will be mailed once the final remedy is available on each phase. Mustang owner notification letters were mailed January 2, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA9. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 14, 2025.
Ford Motor Company (Ford) is recalling certain 2019 Flex, Fiesta, and Lincoln MKT vehicles. The rearview camera may intermittently display a blank or distorted image.
Risk and remedy
Risk
A rearview camera that displays a blank or distorted image can reduce the drivers view of what is behind the vehicle, increasing the risk of a crash.
Remedy
Dealers will replace the rearview camera as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed January 22, 2025. A second notice will be sent once the final remedy is available, anticipated March 2027. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S75.
Ford Motor Company (Ford) is recalling certain 2018 Ford Edge, Lincoln MKX, 2019 Ford Flex, and Lincoln MKT vehicles. The power supply cables at the starter and the alternator may not have been properly secured, possibly resulting in an electrical arc.
Risk and remedy
Risk
An electrical arc can increase the risk of a fire.
Remedy
Ford will notify owners, and dealers will inspect the alternator and starter motor power supply cables to verify that they are properly secured, correcting them as necessary, free of charge. The recall began September 26, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S25.
Owner complaints
260 complaints4 involved a crash3 injuries
What owners report most
Latest complaints
- Unknown or other
UPDATE TO ODI #XXX- 2019 Ford Flex, VIN [XXX], recall 24V951 (Ford 24S75), rearview camera. Camera failed XXX: in reverse the screen turns blue, image flickers off. Still failing. Presented XXX (R.O. #XXX): no repair, no finding. XXX [XXX] [XXX] Ford verified in writing (R.O. #XXX, 63,180 mi)…
UPDATE TO ODI #XXX- 2019 Ford Flex, VIN [XXX], recall 24V951 (Ford 24S75), rearview camera. Camera failed XXX: in reverse the screen turns blue, image flickers off. Still failing. Presented XXX (R.O. #XXX): no repair, no finding. XXX [XXX] [XXX] Ford verified in writing (R.O. #XXX, 63,180 mi): camera at fault, DTC C1001, no repair available, bulletin only tentatively planned Dec 2027, released unrepaired at no charge. Timeline: interim letter XXX said parts not available and promised a second letter when the remedy arrived; none arrived. Remedy anticipated XXX was missed; XXX Ford said no approved remedy or timeline; NHTSA listing now says XXX. No fix, loaner, interim plan, or firm date in nearly 2 years; [XXX] driver uses car daily, and Ford has not told owners to stop driving. XXX I escalated to Ford executive leadership; only reply was a Sep 10 Investor Relations form letter. Question Ford must answer: [XXX] quoted service camera XXX at $124.37 total, listed with no sales restrictions, and Ford's parts printout shows 339 units in stock. Is the delay truly parts availability or the absence of a certified remedy part? Recalled component is GA8T-19G490-A; state in writing whether GA8Z is itself recalled. Please treat as failure to remedy within reasonable time under 49 U.S.C. 30120. ODI closed investigation PE24030 in Feb 2026 relying on this recall, but the promised remedy still does not exist. Require a firm remedy date or interim replacements for verified failures, a binding remedy schedule with progress reporting, and referral to the XXX consent-order monitor ($165 million penalty, independent third-party oversight). Ford's own letter told owners having difficulty getting a repair in reasonable time to contact NHTSA. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Back over prevention
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. While reversing, the rearview camera displayed a blank image. The message "Camera Not Available" was displayed. The dealer was made aware of the failure but confirmed that parts were not yet available. The failure mileage was 50,000.
- Engine
On Tuesday, October 6, 2026 I drove my car without issue and parked in my garage. I later came out and while getting something out of the passenger side noticed fluid leaking out from under the car. After looking at it I decided it looked like the water pump. When I turned the car on it began…
On Tuesday, October 6, 2026 I drove my car without issue and parked in my garage. I later came out and while getting something out of the passenger side noticed fluid leaking out from under the car. After looking at it I decided it looked like the water pump. When I turned the car on it began making engine sounds (no check engine light has come on). With the sound I decided to have the car towed to a mechanic and was told the water pump failed. I chose to have it towed to another mechanic for a second opinion because of the sound and after testing was discovered that the engine is done for. I received no check engine light notification or any other indication that something was wrong. We have kept up with all maintenance for this vehicle so there’s absolutely no reason the water pump or engine should be failing with under 93,000 miles on it. Since we owe $10,000 on the car still we are forced to make the repair with a new engine putting us in a catastrophic financial situation. Water pumps are a known issue with the flex, but for it to occur at such low mileage is insane and for the engine to have failed without any warning is disgusting. On top of this there was a recall for the backup camera in 2024 that still has not been resolved. Our backup camera is upside down, cuts in and out and is not a clear image. We have been dealing with this since shortly after purchasing the vehicle in 2022. When reversing at night I can’t see because the screen is upside down and fuzzy, and when I try to use my mirrors to reverse I am blinded by the light from the screen in the car. Reversing, especially at night, is a huge liability since the drivers vision is not clear. I’ve contacted ford multiple times for an update on the camera recall and have been told there’s no update at this time. We’re going on 3 years of being notified of this recall with zero resolution. I have uploaded a few pictures (estimate is from initial mechanic). I have videos but they will not upload.
- Unknown or other
Rearview camera was recalled almost 2 years ago and still no replacement parts available and the rearview camera in my vehicle does have the issue described. Whenever I put my car in reverse 1 of the following happens every time - Blue screen - Black screen - Image upside down - Distorted image…
Rearview camera was recalled almost 2 years ago and still no replacement parts available and the rearview camera in my vehicle does have the issue described. Whenever I put my car in reverse 1 of the following happens every time - Blue screen - Black screen - Image upside down - Distorted image with lines through it and upside down - Distorted image with lines through it and rightside up - No image with "Camera unavailable" message
- Back over prevention · Structure
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts for the recall repair were unavailable. The contact stated that while in Reverse (R), the rearview camera displayed an…
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts for the recall repair were unavailable. The contact stated that while in Reverse (R), the rearview camera displayed an upside-down image, posing a safety hazard while attempting to attach a trailer to haul. A local dealer was contacted and confirmed the failure. The manufacturer was notified of the failure by telephone. The failure mileage was approximately 50,000.
- Back over prevention
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to complete the recall repair was not yet available. The contact stated that while the vehicle was in Reverse (R), the rearview camera displayed a blank…
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to complete the recall repair was not yet available. The contact stated that while the vehicle was in Reverse (R), the rearview camera displayed a blank or distorted screen. The dealer was contacted. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure by telephone. The failure mileage was approximately 31,000.
- Electrical system
Rear View camera image is upside down / distorted. Looks to be acknowledged by Ford and NHTSA as a recall yet Ford Dealers are making me pay to have it fixed.
- Back over prevention
The contact owns a 2019 Ford Flex. The contact stated that while reversing, the rear-view camera displayed an upside-down image and occasionally the rear-view camera displayed an image with lines. The dealer was contacted by phone and made aware of the failure. The contact was informed that parts…
The contact owns a 2019 Ford Flex. The contact stated that while reversing, the rear-view camera displayed an upside-down image and occasionally the rear-view camera displayed an image with lines. The dealer was contacted by phone and made aware of the failure. The contact was informed that parts were unavailable to repair the vehicle. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The failure mileage was approximately 115,000.
- Back over prevention · Structure
The contact owns a 2019 Ford Flex. The contact stated that while in reverse(R), the rear-view camera displayed a blank screen or a distorted image. The contact then received notifications of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to do…
The contact owns a 2019 Ford Flex. The contact stated that while in reverse(R), the rear-view camera displayed a blank screen or a distorted image. The contact then received notifications of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to do the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the repairs. The dealer was notified of the failure several times, and the contact was informed that parts were not yet available. The failure mileage was approximately 45,000.
- Back over prevention · Structure
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, parts for the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for…
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, parts for the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for parts to be available. The contact stated that while driving approximately 45 MPH, the B-pillar trim on the front driver's side door detached from the top of the door, causing the top half of the trim to separate from the rest of the trim. The contact stated that the same trim on the rear driver's side door had slightly detached. The back over prevention camera was inoperable and only displayed a black screen and made a beeping sound while in reverse. The dealer was contacted and failed to confirm when parts would be available. The failure mileage was approximately 80,000.
- Back over prevention
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rear-view camera was inoperable. The message "Camera…
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rear-view camera was inoperable. The message "Camera Unavailable" was displayed, requiring the contact to press OK. The dealer was contacted several times and confirmed that parts were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 46,000.
- Unknown or other
I've been waiting for the recall repairs for the rear view camera for 1 1/2 years. Backing without this safety equipment is a hazard. I'm a patient person, but this is ridiculous.
- Back over prevention · Structure
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts for the recall repairs were unavailable. The contact stated the manufacturer had exceeded a reasonable amount of time to…
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts for the recall repairs were unavailable. The contact stated the manufacturer had exceeded a reasonable amount of time to make the parts available. The contact stated that when in reverse, the back over prevention camera displayed the image at the rear of the vehicle in reverse. The dealer was contacted twice and, most recently, advised the contact to wait an additional six months for parts. The failure mileage was approximately 45,000.
- Back over prevention › Rearview system braking · Unknown or other
Recieved recall notice 24S25 / NHTSA 24V951XXX about defected rear view camera malfunction. I have had an ongoing issue with camera not operating correctly. I have made several calls to Ford dealership and continued to be told parts not available. Why issue a recall and after 20 months latter…
Recieved recall notice 24S25 / NHTSA 24V951XXX about defected rear view camera malfunction. I have had an ongoing issue with camera not operating correctly. I have made several calls to Ford dealership and continued to be told parts not available. Why issue a recall and after 20 months latter still no fix. I am sure if I paid to have camera fixed the parts would be available. Is there a date parts will be available. Please help. [XXX] [XXX] VIN # [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Back over prevention
The contact owns a 2019 Ford Flex. The contact stated that while attempting to reverse, the rear-view camera became inoperable. The contact stated that the rear-view camera image was intermittently blurry or inverted. The contact received notifications of NHTSA Campaign Number: 25V695000 (Back Over…
The contact owns a 2019 Ford Flex. The contact stated that while attempting to reverse, the rear-view camera became inoperable. The contact stated that the rear-view camera image was intermittently blurry or inverted. The contact received notifications of NHTSA Campaign Number: 25V695000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to complete the recall repairs were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time to provide a remedy for the recalls. The approximate failure mileage was 95,000.
- Unknown or other
My backup camera is not working intermittently or will display a grainy image or black and blue lines. Sometimes it will just be a black screen. Other models of my vehicle had the backup camera recalled but my dealer is saying my vin isn’t included in the recall.
- Back over prevention › Rearview system braking · Structure › Body
Exterior b-pillar applique trim on front driver and passenger doors have ripped from the vehicle while driving. Driver side trim includes key code pad and wires. Dealer has no parts available and taking no appointments. Rear camera not working consistently. Dealer has no parts available and taking no appointments.
- Unknown or other
My backup camera is not working all the time, sometimes it comes on but more than not it doesn’t work, I contacted a Dealer and they said there is no solution for this issue.
- Unknown or other
Getting on Interstate 35 at Bevington, Iowa and heard a noise at drivers side window and a piece of trim broke in 2 pieces, scared me and I pulled over on the Interstate to look and there was a piece hanging from some wires on drivers door
- Back over prevention
The contact owns a 2019 Ford Flex. The contact stated that the rear-view camera was inoperable. While reversing in the driveway, the camera operated intermittently. The contact stated that it was difficult to reverse from a parking spot. The contact received notification of NHTSA Campaign Number…
The contact owns a 2019 Ford Flex. The contact stated that the rear-view camera was inoperable. While reversing in the driveway, the camera operated intermittently. The contact stated that it was difficult to reverse from a parking spot. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention). The contact called the local dealer ten times and was informed that parts were not yet available and that vehicle owners would be notified when the parts became available.
- Power train · Steering · Suspension
As with many other 2019 Flex owners, I brought my Ford Flex in for a state inspection and surprise surprise! I have to replace my toe link already! Failure after failure.
- Back over prevention · Structure
The contact owns a 2019 Ford Flex. The contact received notifications for NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to perform the recall repairs were not yet available. The contact experienced both failures. The contact stated that upon…
The contact owns a 2019 Ford Flex. The contact received notifications for NHTSA Campaign Numbers: 24V951000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to perform the recall repairs were not yet available. The contact experienced both failures. The contact stated that upon shifting into reverse, the rearview camera displayed a blank or distorted image, and the B-pillar trims detached. The dealer was contacted; however, the vehicle was not diagnosed or repaired because the recall remedies were unavailable. The contact stated that the manufacturer had failed to provide a remedy in a timely manner. The manufacturer was not notified of the failure. The failure mileage was 100,000.
- Back over prevention · Structure
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V695000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that while reversing, the rear-view camera was…
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V695000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that while reversing, the rear-view camera was inoperable. Additionally, the driver's side B-pillar trim detached, allowing water to leak into the vehicle. The vehicle was taken to the dealer, where it was inspected but not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure. The failure mileage was approximately 50,000.
- Back over prevention · Structure
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V829000 (Structure) and 25V695000 (Back Over Prevention); ); however, the parts to do the recall repairs were not yet available. The contact stated that the manufacturer had exceeded a reasonable…
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V829000 (Structure) and 25V695000 (Back Over Prevention); ); however, the parts to do the recall repairs were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the front driver's and passenger's side door B-pillar trims had detached, causing wind noise while driving. Additionally, the rear-view camera displayed a distorted image while reversing. The dealer was made aware of the failure but confirmed that parts were not yet available. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 70,000.
- Structure
See attached document for complaint.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- B-Pillar Trim Detachment
On August 7, 2025, the Office of Defects Investigation (ODI) opened PE25007 to investigate instances of B-pillar trim detachment in model year (MY) 2019 Ford Flex vehicles manufactured by Ford Motor Company. During the investigation, MY 2011-2018 Ford Flex vehicles were analyzed as peer vehicles, and subsequently…
On August 7, 2025, the Office of Defects Investigation (ODI) opened PE25007 to investigate instances of B-pillar trim detachment in model year (MY) 2019 Ford Flex vehicles manufactured by Ford Motor Company. During the investigation, MY 2011-2018 Ford Flex vehicles were analyzed as peer vehicles, and subsequently incorporated into the subject population because they use B-pillar trim pieces that are substantially similar to those used on the MY 2019 Ford Flex vehicles. In July 2025, prior to the opening of PE25007, ODI and Ford met to discuss B-pillar trim detachment in Ford Flex vehicles. Ford reported that its warranty analysis indicated that Flex B-pillar trim had a low detachment rate and that Ford did not believe this condition posed an unreasonable risk to motor vehicle safety. In July 2025, Ford closed its internal investigation. Because ODI’s analysis of complaint data indicated a high failure rate and an increasing failure trend, PE25007 was subsequently opened. In responding to the information request for PE25007, Ford reassessed the warranty search criteria used in its July 2025 internal investigation. The reassessment found the detachment rate to be substantially higher than what Ford had originally determined. Consequently, in October 2025, Ford issued recall 25V732based on the reassessed and accurate high failure rate. This recall instructed dealers to inspect the driver and front passenger B-pillar trim pieces and repair/replace if necessary. The vehicles included in this recall were MY 2017-2019 Ford Flex with production dates between February 17, 2017 and December 2, 2019. In January 2026, Ford issued 25V732 Amendment 1, which updated the remedy to remove the inspection criteria and instead proactively secure the driver and front passenger B-pillar trim with adhesive. The scope of vehicles included in the recall was unchanged by Amendment 1. ODI’s analysis of 25V732 found that both the scope and remedy were insufficient and that an unreasonable safety risk remained despite the recall. MY 2016 Ford Flex was excluded from the recall scope and the rear B-pillar trims on both the driver and passenger side were excluded from the recall. The failure rates of both MY 2016 Ford Flex and rear B-pillar trim pieces were found to be higher than the failure rates in similar trim detachment recalls issued by both Ford and other vehicle manufacturers. Starting in January 2026, ODI and Ford had multiple meetings to discuss Ford’s PE25007 response data and ODI’s concern about the 25V732 scope and remedy. In June 2026, Ford issued 25V732 Amendment 2. This amendment expanded the scope of the recall to add MY 2016-2017 Ford Flex vehicles produced before February 17, 2017. Additionally, this amendment updated the remedy to include removal of and reapplication or replacement of both rear driver and rear passenger B-pillar trim pieces in addition to front driver and front passenger B-pillar trim pieces. This updated remedy applies to all MY 2016-2019 vehicles. Ford expects to complete the mailing of remedy owner notification letters by March 26, 2027. Also, Ford informed ODI that prior model year (MY 2011-2015) vehicles were referred to Ford’s Customer Satisfaction forum for consideration of an extended warranty program. In view of recall 25V732 and its associated amendments, ODI is closing this Preliminary Evaluation (PE). The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Rear-view Camera Failure
On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted…
On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted, or inverted rear-view camera images when in reverse. An inverted or upside-down image can provide false information to the driver increasing the risk of a crash. To date, ODI has received 85 VOQ complaints and additional EWR Field Reports with these allegations for MY 2019 Ford Flex vehicles. During the investigation, ODI found that the MY 2019 Ford Flex vehicle and certain peer vehicles including MY 2015-2018 Flex, MY 2019 Fiesta, Taurus, and Lincoln MKT vehicles are equipped with Magna analog rear-view-only cameras. On December 20, 2024, Ford filed Recall 24V-951 covering 30,715 MY 2019 Ford Flex, Ford Fiesta, and Lincoln MKT vehicles in which the rear-view camera may intermittently display a blank or distorted image. The dealers will replace the rear-view camera for vehicles in the recall population. Per the recall chronology, teardown of three cameras identified fractured solder joints between the microcontroller and the printed circuit board. Ford indicated that other causal factors are being investigated and asserted that the defect is contained within the camera. ODI found that certain peer vehicles excluded from Recall 24V-951 showed a high rate of VOQ complaints. Also, ODI identified reports produced by Ford that indicate the peer vehicles have the same issue as the subject vehicles. To address ODI’s concern, Ford analyzed some field-returned cameras, as well as Ford’s field data and ODI’s VOQ data. Ford stated it did not identify a specific root cause in the Magna supplied cameras. However, on October 13, 2025, Ford filed Recall 25V-695 covering 1,448,655 vehicles of various Ford/Lincoln models equipped with Magna supplied cameras. The cameras demonstrate the same blank or distorted images that prompted Recall 24V-951. It should be noted that Ford is conducting a recall of those vehicles by model/model year that exhibit VOQ complaint rates greater than 10 per 100,000 vehicles. For the remaining vehicles (rates less than 10/100K), Ford is providing a warranty extension (15 years/unlimited miles). Ford has stated that the differences in the rates (field performance) are likely due to the differences in the camera related hardware, such as the wiring harness type that are specific by vehicle model/model year. In view of Ford filing Recall 24V-951 and Recall 25V-695 addressing the subject of this investigation, ODI is closing this Preliminary Evaluation. NHTSA reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11008948While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
- 11001174This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
- 10240743The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
- 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
- 10217028Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
- 10208146Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
- 10205694Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
- 10201050Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10201013Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
- 10198605Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
- 10194428Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10187930Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
- 10184779Some 2016-2019 Flex vehicles equipped with a factory keyless entry keypad may exhibit a loose driver side B-pillar front door upper moulding. This may be caused by a lack of adhesion of the front door upper moulding to the door. To correct the condition, follow the Service Procedure steps to reapply adhesive tape to the front door trim panel.
- 10181913Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
- 10180428Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
- 10179331Some 2019 Flex vehicles equipped with SYNC 3 without navigation may exhibit a compass that is stuck and/or does not indicate the correct direction. This may be due to the calibration in the accessory protocol interface module (APIM). To resolve the concern, reprogram the APIM using the latest level of the appropriate Ford scan tool. The SYNC 3 universal thumb drive should not be used to correct this condition. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10179117Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
- 10177863This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
- 10177042Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
- 10174421Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
- 10172972SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
- 10169986Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10169903Some 2019 Flex vehicles equipped with SYNC 3 without navigation may exhibit a compass that is stuck and/or does not indicate the correct direction. This may be due to the calibration in the accessory protocol interface module (APIM). To resolve the concern, reprogram the APIM using the latest level of the appropriate Ford scan tool. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10168810Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
- 10164596Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10164508Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
- 10164497For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
- 10163573Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Use pigtail harness service part numbers 3U2Z-14S411-ZEA or CU2Z-14S411-FA, as both parts are interchangeable. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures.
- 10163568Some 2018-2019 Explorer/Flex/Taurus/MKT vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure to replace the MAPT sensor.
- 10163554Some 2018-2019 Explorer/Flex/Taurus/MKT vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure to replace the MAPT sensor.
- 10162087Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
- 10162063Some 2018-2019 Explorer/Flex/Taurus/MKT vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure steps to diagnose and replace the MAPT sensor.
- 10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
- 10160880Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10159494SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
- 10159489Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10156877Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
- 10155565Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
Every Ford Flex model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.