2015 Ford Flex
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2015 Ford Flex. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2015 Ford Flex. Newest first.
Ford Motor Company (Ford) is recalling certain 2015-2019 Flex, 2015 Explorer, Lincoln MKT, Lincoln MKZ, 2015-2016 C-Max, Escape, Taurus, 2016 Fusion, 2018-2019 Taurus, 2019 Lincoln MKT, Fiesta, and 2020 Mustang vehicles. The rearview camera may display a distorted, intermittent, or blank image when the vehicle is in reverse.
Risk and remedy
Risk
A rearview camera that fails to properly display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy
Dealers will inspect and replace the rearview camera as necessary, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on October 25, 2025. Additional letters will be mailed once the final remedy is available on each phase. Mustang owner notification letters were mailed January 2, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA9. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 14, 2025.
Ford Motor Company (Ford) is recalling certain 2013-2018 Lincoln MKT and Ford Flex and Taurus vehicles with the Police Interceptor or SHO Performance Pack. The rear suspension toe links may fracture due to stress on the rear suspension.
Risk and remedy
Risk
A fractured rear toe link will cause a sudden change in vehicle handling and increase the risk of a crash.
Remedy
Ford will notify owners, and dealers will replace the rear suspension toe links, free of charge. Remedy parts are not currently available. Owners were notified about the recall on March 3, 2020. A second notice will be mailed when remedy parts become available, which is currently expected to be the end of September 2020. The recall began October 28, 2020. Owners may contact Ford customer service at 1-866-436-7332 or Lincoln customer service at 1-800-521-4140. Ford's number for this recall is 20S04.
Ford Motor Company (Ford) is recalling certain model year 2013-2015 Ford Taurus, Ford Flex, Lincoln MKS and Lincoln MKT vehicles equipped with 3.5L GTDI Ecoboost engines and 2013-2015 Ford Taurus Police Interceptor vehicles. A component within the fuel pump electric module (PEM) may overheat causing a loss of electrical power to the fuel pump.
Risk and remedy
Risk
A loss of power to the fuel pump will cause the engine to stall or prevent the vehicle from starting, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will inspect the fuel PEM part number and replace the fuel PEM, as necessary, free of charge. The recall began on December 1, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S31.
Ford Motor Company (Ford) is recalling certain model year 2015 Ford Taurus, Ford Flex, and Lincoln MKS vehicles manufactured May 4, 2015, to May 23, 2015, Lincoln MKT vehicles manufactured May 4, 2015, to May 21, 2015, and 2015-2016 Ford Explorer vehicles manufactured May 4, 2015, to May 23, 2015. The affected vehicles have a parking brake that may not…
Risk and remedy
Risk
If the parking brake does not fully engage and the transmission is left in a gear other than 'Park' while on a slope, the vehicle may roll away, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will test the operation of the parking brake system, and if necessary, replace the parking brake control assembly, free of charge. The recall began on September 4, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15C07.
Owner complaints
116 complaints2 involved a fire1 injuries
What owners report most
Latest complaints
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V69500 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V69500 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. While reversing, the rear-view camera displayed an upside-down image. The dealer was made aware of the failure but confirmed that parts were not yet available. The manufacturer was notified of the failure by phone. The failure mileage was 140,000.
- Unknown or other
Backup camera doesn't work all the time
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part needed to complete the recall repair was not available. The contact stated that while reversing, the rearview camera became inoperable. The contact…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part needed to complete the recall repair was not available. The contact stated that while reversing, the rearview camera became inoperable. The contact stated that the rearview camera image was blank with the "Camera Not Available" message, inverted or distorted with lines. The vehicle was taken to the dealer, where a rearview camera failure was diagnosed and camera replacement was required. The dealer confirmed that the parts were unavailable and offered to perform the repair at the contact's expense. The contact stated that the manufacturer exceeded a reasonable amount of time to provide a remedy for the recall. The manufacturer was notified of the failure. The failure mileage was unavailable.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact stated that while the vehicle was in reverse(R), the rear-view camera displayed a blank image, a blue image, a distorted image, or the message “Camera Unavailable” was displayed. The contact received notification of NHTSA Campaign Number: 25V695000…
The contact owns a 2015 Ford Flex. The contact stated that while the vehicle was in reverse(R), the rear-view camera displayed a blank image, a blue image, a distorted image, or the message “Camera Unavailable” was displayed. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The dealer was notified several times of the failure, and the contact was informed that the part for the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure, and the contact was provided similar information that was provided by the dealer.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rear-view camera was intermittently inoperable. The dealer…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rear-view camera was intermittently inoperable. The dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 82,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while shifted in reverse, the rear-view camera failed to display a clear image.…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while shifted in reverse, the rear-view camera failed to display a clear image. The local dealer was contacted on a separate occasion, and the rearview camera was replaced; however, the failure reoccurred. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 130,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part for the repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the part to be available. While in…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part for the repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the part to be available. While in reverse, the back over prevention camera displayed an inverted image. However, within the past 3 months, the camera failed to operate as needed and displayed the message, “Camera Unavailable”. The dealer was contacted several times. The dealer informed the contact that parts would be available in April and then stated June. The dealer most recently informed the contact that only Mustangs were being repaired, and there was no ETA when parts would be available. The manufacturer was made aware of the issue. The failure mileage was approximately 98,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while reversing, the rear-view camera failed to display an image. The dealer was made aware of the failure but confirmed that parts were not yet available. The manufacturer was notified of the failure by phone. The failure mileage was approximately 100,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact stated that while the vehicle was in reverse, the rear-view camera displayed a blank screen with the message “Camera Unavailable” displayed. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part…
The contact owns a 2015 Ford Flex. The contact stated that while the vehicle was in reverse, the rear-view camera displayed a blank screen with the message “Camera Unavailable” displayed. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was contacted by phone and made aware of the failure. The failure mileage was approximately 15,500.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact stated that while reversing, the message “See Dealer Soon” was displayed, the rear-view camera independently turned off, and the screen was blank. The dealer was made aware of the failure by phone. The vehicle was taken to the dealer, and the contact…
The contact owns a 2015 Ford Flex. The contact stated that while reversing, the message “See Dealer Soon” was displayed, the rear-view camera independently turned off, and the screen was blank. The dealer was made aware of the failure by phone. The vehicle was taken to the dealer, and the contact was informed that the parts were unavailable to repair the vehicle. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The manufacturer was contacted by phone, and a case was filed. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was approximately 45,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while reversing, the rear-view camera displayed a blank image. The dealer was made aware of the failure but confirmed that parts were not yet available for the recall repair.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention). The contact stated that while in reverse(R) on several occasions, the rear-view camera screen was black with the message "Contact Dealer" displayed. The contact stated…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention). The contact stated that while in reverse(R) on several occasions, the rear-view camera screen was black with the message "Contact Dealer" displayed. The contact stated that the home screen on the rear-view camera failed to turn on. The contact stated that on three occasions while in reverse(R), an individual was nearly struck by the vehicle. The vehicle was taken to a dealer but was not diagnosed or repaired. The contact was informed that there was no current fix for the failure. The manufacturer was notified of the failure. The failure mileage was approximately 70,000.
- Unknown or other
UNKNOWN The rear camera (when available) is UPSIDE DOWN! At night, the image also has wide lines running through it. Sometime, the camera just shows a message that it is unavailable. So FRUSTRATING!
- Back over prevention
The contact owns a 2015 Ford Flex. The contact stated that upon reversing the vehicle the rearview camera display would display upside down and then display blank and no warning lights were illuminated, however the following warning message would display on the instrument panel "camera unavailable…
The contact owns a 2015 Ford Flex. The contact stated that upon reversing the vehicle the rearview camera display would display upside down and then display blank and no warning lights were illuminated, however the following warning message would display on the instrument panel "camera unavailable, please contact your local dealer". The local dealer was contacted however the vehicle was not repaired as the contact was advised that the remedy for NHTSA campaign number :25V695000 (BACK OVER PREVENTION) was not yet available. The manufacturer was not notified of the failure. The failure mileage was 120,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact stated that while reversing, the rear-view camera was blank. There was no warning light illuminated; however, the message was "Camera not Available - Please Contact your Dealer" was displayed on the instrument panel. The contact received notification…
The contact owns a 2015 Ford Flex. The contact stated that while reversing, the rear-view camera was blank. There was no warning light illuminated; however, the message was "Camera not Available - Please Contact your Dealer" was displayed on the instrument panel. The contact received notification of NHTSA Campaign Number: 25V695000 (BACK OVER PREVENTION). The local dealer was contacted; however, the vehicle was not repaired because parts were not yet available for the recall repair. The manufacturer was contacted but was not notified of the failure. The failure mileage was 65,000.
- Electrical system
Rear view camera under recall. Told by Ford for 3 months in a row that should receive paper in mail for recall repair. Have not received paper. Very dangerous backing up.
- Unknown or other
Rear Camera no working. This Ford recall has been out for 3 years now and we still cannot get a remedy for our vehicle!
- Back over prevention
See attached document for complaint.
- Visibility/wiper
Rear (Backup} camera malfunctioning. Recall 25V6595. Two (2) Dealers state that there is no recall (Fritt's Ford, Raceway Ford Riverside Ca). VIN [XXX] This is ongoing. There was no accident. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (BACK OVER PREVENTION); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (BACK OVER PREVENTION); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. While reversing, the back over prevention camera image appeared upside down, or the message “Camera Not Available" was displayed. The vehicle was not repaired. The failure mileage was 160,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention). The contact stated that on several occasions, while in reverse (R), the image was flipped upside down or the screen was blank. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was unknown.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that upon purchase from an independent local dealer and shifting into reverse(R), the…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that upon purchase from an independent local dealer and shifting into reverse(R), the rearview camera failed to display a clear image. The screen was black. No warning light was illuminated. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 130,000.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that back over prevention screen was black while shifted into reverse. The approximate failure mileage was 115,000.
- Unknown or other
My 2015 Ford Flex is affected by recall 25V695 for the rear view camera inspection. I contacted my local Ford dealership to have the recall addressed and was told that no remedy parts are available at any dealership. They could not provide a timeline for when parts would be in stock. This vehicle…
My 2015 Ford Flex is affected by recall 25V695 for the rear view camera inspection. I contacted my local Ford dealership to have the recall addressed and was told that no remedy parts are available at any dealership. They could not provide a timeline for when parts would be in stock. This vehicle is part of my commercial fleet and cannot be operated or rented until the recall is resolved. I am losing over $1,200 per month in revenue because Ford issued a recall with no fix available. Owners should not be forced to absorb open-ended financial losses because the manufacturer cannot supply the parts needed to complete its own recall.
- Back over prevention
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The…
The contact owns a 2015 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while in reverse(R), the back over prevention camera intermittently failed to operate before the back over prevention camera permanently failed to operate. The dealer was contacted. The manufacturer was not made aware of the issue. The failure mileage was approximately 140,000.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11008948While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
- 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
- 10214492Some 2015-2016 vehicles equipped with 6F50/6F55 transmission and built on 2-Nov-2015 and through 1-Feb-2016 may exhibit no reverse, 3rd and 5th gear with diagnostic trouble codes (DTCs) P0715,P0717,P0756 and/or P2701. This may be caused by the direct clutch cylinder/tone wheel (7F283) inadvertently forcing the snap ring out of position resulting in damage to the direct clutch hub (7G384). Service part (7J250) complete rotating 3-5-R clutch module is now available. Refer to Workshop Manual (WSM), Section 307-01. For claiming, use causal part 7F283 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) manual.
- 10205031Touchscreen navigation system - arabic language - blank screen
- 10201050Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10194428Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10183749In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market
- 10180428Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
- 10172972SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
- 10169986Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10164596Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10164508Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
- 10164497For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
- 10163573Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Use pigtail harness service part numbers 3U2Z-14S411-ZEA or CU2Z-14S411-FA, as both parts are interchangeable. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures.
- 10162086Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 101609362015-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police vehicles built on or before 10-Jun-2016 and equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) may exhibit a PTU venting, an odor originating from the PTU, or noise originating from the PTU. These vehicles may be a candidate for rebuild using PTU Idler Gear/Shaft/Bearing Kit (GB5Z-7P258-A). Refer to Workshop Manual (WSM), Section 308-07.
- 10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
- 10160880Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10159494SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
- 10159489Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10156877Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
- 10155565Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
- 10153969Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
- 10152473For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
- 10144215Some 2015-2018 Flex, Taurus, Police Interceptor Sedan, and 2016 Navigator vehicles may exhibit a turn signal that does not operate as expected when the steering column multifunction switch is moved to the lane change position, then quickly changed to the opposite direction detent position before the lane change flashes three times. Reprogram the Steering Column Control Module (SCCM) using the appropriate Ford scan tool or equivalent release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 3F791 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10140323The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10138524The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10137131Some 2007-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Police Interceptor Sedan/Explorer/Police Interceptor Utility vehicles equipped with AWD and built on or before 30-Jun-2016 may exhibit a propane or natural gas odor during idle or low speed driving. This may be due to break down of the power transfer unit (PTU) fluid caused by excessive heat. If the source of the odor is identified as originating from the PTU, an idler bearing repair kit is available to repair the PTU. Refer to the Workshop Manual (WSM), Section 308-07. If the PTU is determined to be repairable, utilize kit GB5Z-7P258-A and the included instruction sheet. For claiming use causal part 7P258 and applicable labor operations in section 07 of the Service Labor Time Standards (SLTS) Manual.
- 10137113Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
- 101365972010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
- 10127405Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
- 10119686Certain 2015 Model Year Flex and Taurus, 2015-2016 Model Year C-MAX, and MKS, and 2016 Model Year Edge, Fusion, MKZ, and Transit Connect Vehicles - Electronic Throttle Body Replacement
- 10115953Some 2013-2017 Edge/MKX/Escape/MKC/Fusion/MKZ/Flex/MKT/Mondeo/Kuga/EcoSport AWD vehicles where diagnosis leads to a RDU clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.
- 10109079Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
- 10109070The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
- 10109063Some 2015-2016 vehicles equipped with 6F50/6F55 transmission Built On 11/2/2015 And Through 2/1/2016 may exhibit no reverse, 3rd and 5th gear and/or DTCs P0715, P0717, P0756 and/or P2701. This may be caused by the direct clutch snap ring out of position and/or damage to the direct clutch hub. The cause of the failure is the Tone Wheel surface putting uneven load on the snap ring. To repair this condition the Tone Wheel (7F283) must be replaced,(also referred to as Direct Clutch Cylinder/Tone wheel) in addition to the Tone Wheel, replace Direct Clutch Hub (7G384), Direct Clutch Return Spring (7F235), Direct Clutch Snap Ring (7C122), TSS Sensor (7M101), Seal Kit (7153) and filter in the kit. Disassemble, clean the transmission and main control to remove metal particles. Refer to WSM, Section 307-01. Use causal part 7F283 and applicable Labor ops from SLTS section 7.
- 101090122013-2017 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police/Continental vehicles equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) that is being repaired or replaced for an internal failure must also have the vent hose replaced due to contamination in the hose.
- 10095995Some 2010-2016 epas equipped vehicles may exhibit steering related noises. The workshop manual (wsm) diagnostic procedures have been updated in section 211-02. When diagnosing and repairing epas steering noises use the updated procedures.
Every Ford Flex model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.