2018 Ford Focus
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Ford › Focus › 2018
These records cover every 2018 Ford Focus. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2018 Ford Focus. Newest first.
Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
Risk and remedy
Risk
An engine that stalls while driving increases the risk of a crash.
Remedy
Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Ford Motor Company (Ford) is recalling certain 2015-2018 Focus and 2013-2016 Fusion vehicles previously repaired incorrectly under recall numbers 18V169 and 18V845. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Risk and remedy
Risk
A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy
Dealers will update the software, free of charge. Additionally, dealers will inspect Focus vehicles and replace the clutch assembly as necessary, free of charge. Owner notification letters were October 16, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S43. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Risk and remedy
Risk
An electrical short circuit can increase the risk of a fire.
Remedy
Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026.
Ford Motor Company (Ford) is recalling certain 2016-2018 Focus, 2019 Explorer, and 2024 Explorer vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Risk and remedy
Risk
An electrical short circuit can increase the risk of a fire.
Remedy
Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed February 13, 2026. Additional letters will be sent once the final remedy is available, anticipated in December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026. This recall expands previous recall number 25V685.
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The oil pump drive belt or drive belt tensioner may fail, resulting in a loss of engine oil pressure.
Risk and remedy
Risk
A loss of oil pressure can result in an engine stall and a loss of power braking assist, increasing the risk of a crash.
Remedy
Dealers will replace the oil pump tensioner assembly and oil pump drive belt, free of charge. If engine failure occurs due to a damaged oil pump belt and/or oil pump belt tensioner, Ford has authorized dealers to replace the engine assembly as an interim repair before the availability of remedy parts for the final repair. This repair will be free of charge (parts and labor). Owner notification letters were mailed August 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S64.
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus vehicles equipped with a 1.0L Fox GTDI engine and a 6-speed manual transmission. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Risk and remedy
Risk
A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy
Ford will notify owners, and dealers will update vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. The recall began January 17, 2019. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 18S07. Note: This recall is an expansion of Recall 18V-169.
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Risk and remedy
Risk
The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Owner complaints
837 complaints15 involved a crash3 involved a fire11 injuries
What owners report most
Latest complaints
- Fuel/propulsion system · Unknown or other · Vehicle speed control
when the vehicle accelerates too quickly or up a very gradual hill, barely any slope, it will slow to a stop. this is in line with the current recalls with other Ford focus 2018s likely caused by the Canister Purge Valve. it has the exact same symptoms, poor fuel economy, rough idling so much so…
when the vehicle accelerates too quickly or up a very gradual hill, barely any slope, it will slow to a stop. this is in line with the current recalls with other Ford focus 2018s likely caused by the Canister Purge Valve. it has the exact same symptoms, poor fuel economy, rough idling so much so the entire vehicle shakes, and the dangerous part- stalling. I have now stalled 4 times and have been in and out of multiple mechanics for this issue and no one can seem to identify the root and it's getting costly. now they are saying it might be the canister purge valve but if it is I think it should be covered despite my vin not being perfectly aligned because it's ultimately the same issue with the same vehicle, make and model.
- Engine
The contact owns a 2018 Ford Focus. The contact stated that after the vehicle was repaired under a recall, while driving 45 MPH, the vehicle unexpectedly idled, causing the engine to misfire with the check engine warning light illuminated. The contact stated that the vehicle sputtered during the…
The contact owns a 2018 Ford Focus. The contact stated that after the vehicle was repaired under a recall, while driving 45 MPH, the vehicle unexpectedly idled, causing the engine to misfire with the check engine warning light illuminated. The contact stated that the vehicle sputtered during the misfire. The vehicle was taken to the dealer, where the contact was informed that the engine needed to be repaired. The vehicle was repaired; however, the failure recurred. The vehicle was taken back to the dealer to be diagnosed, and it was determined that the cylinder wall had failed and the engine needed to be replaced. The contact was concerned that the failure was caused by an improper recall repair. The contact stated that the failure had not occurred until after the recall repair was performed. The manufacturer was made aware of the failure by telephone, and a case was opened. The failure mileage was approximately 63,126.
- Power train
My car had been driving fine. Until one day I leave my house and crank my car up and it does not go into reverse. It loses engine power and stalled into traffic. This is an on going issue as you can see stories from other people with the same make and model as my car with the same issue. No warning…
My car had been driving fine. Until one day I leave my house and crank my car up and it does not go into reverse. It loses engine power and stalled into traffic. This is an on going issue as you can see stories from other people with the same make and model as my car with the same issue. No warning signs, hasn’t been checked out but I have contacted Ford and they only cover models with this issue 2012-2016. I think it should cover 2018 as well.
- Vehicle speed control
"My 2018 Ford Focus was traveling uphill at highway speed. I fully depressed the accelerator because the vehicle was losing speed. The vehicle did not respond with additional acceleration and subsequently continued to lose speed despite the accelerator remaining fully depressed. The dealership…
"My 2018 Ford Focus was traveling uphill at highway speed. I fully depressed the accelerator because the vehicle was losing speed. The vehicle did not respond with additional acceleration and subsequently continued to lose speed despite the accelerator remaining fully depressed. The dealership inspected the vehicle and told me that the engine is not powerful enough for sustained uphill driving and that the vehicle performed as designed. I am reporting this because I am concerned about the loss of ability to maintain speed despite full accelerator input and whether this constitutes a safety defect."
- Engine and engine cooling
The contact owns a 2018 Ford Focus. The contact stated that on several occasions while driving uphill, the vehicle lost power, the check engine warning light illuminated, and the message "Engine Fault" was displayed. The contact inspected the vehicle and noticed that the check valve on the vacuum…
The contact owns a 2018 Ford Focus. The contact stated that on several occasions while driving uphill, the vehicle lost power, the check engine warning light illuminated, and the message "Engine Fault" was displayed. The contact inspected the vehicle and noticed that the check valve on the vacuum pump had separated. The check valve was replaced every 1,000 miles. The contact stated that while driving approximately 35 MPH, the vehicle lost power and the oil warning light flashed. The vehicle was taken to the residence and parked. The contact inspected the vehicle and checked the dipstick, noticing bits of rubber inside the oil. The failure mileage was approximately 32,000.
- Engine
My Ford vehicle has experienced repeated and significant engine problems that have never been successfully resolved despite numerous repair attempts at multiple Ford dealerships. The engine has been repaired/rebuilt multiple times, yet the underlying issue has continued and the engine has now…
My Ford vehicle has experienced repeated and significant engine problems that have never been successfully resolved despite numerous repair attempts at multiple Ford dealerships. The engine has been repaired/rebuilt multiple times, yet the underlying issue has continued and the engine has now seized. Most concerning, the vehicle unexpectedly shut off. Fortunately, it started again yesterday, but I do not consider it safe to drive because I am concerned it could shut off again while being driven, causing a sudden loss of power and creating a serious safety risk. Ford is declining further assistance because the vehicle odometer is approximately 105,000 miles. However, the engine has been rebuilt multiple times and has substantially fewer miles since its most recent rebuild. This is not simply an engine that failed for the first time at 105,000 miles; it is an ongoing problem that Ford dealerships have repeatedly attempted and failed to correct. Ford has advised that its assistance for this known issue is a "program," not a warranty. If Ford is aware of an engine condition that can result in repeated failures, engine seizure, or an unexpected shutdown/loss of power, I believe the safety implications should be investigated. I am asking NHTSA to determine whether this is part of a broader safety defect affecting this Ford model/engine and whether a safety recall or other action is warranted. I have extensive dealership repair records and Ford correspondence documenting the history.
- Engine · Unknown or other · Visibility/wiper
First my wind shield wipers were coming on by themselves and not cutting off when I flicked the switch. Now my car is jerking when I press the gas to drive and sometimes moving in reverse after I press the gas to drive. Jerking and barely accelerating, then it decides to driver in between gaps. My…
First my wind shield wipers were coming on by themselves and not cutting off when I flicked the switch. Now my car is jerking when I press the gas to drive and sometimes moving in reverse after I press the gas to drive. Jerking and barely accelerating, then it decides to driver in between gaps. My safety is put at risk because sometimes it slows down or barely accelerates in oncoming traffic and moves backwards when cars are behind me at a light or stop sign. Manufacture by others which is a neighborhood auto shop. Just the check engine light came on.
- Engine · Fuel/propulsion system
There was supposedly a recall of 2012-2018 Ford focuses such as mine, which is a 2018, but somehow my car is not included in this recall even though it seems to be affected by the same problem. I believe it to have a faulty purge valve (forgive me if I am not precise in my terminology) as it stalls…
There was supposedly a recall of 2012-2018 Ford focuses such as mine, which is a 2018, but somehow my car is not included in this recall even though it seems to be affected by the same problem. I believe it to have a faulty purge valve (forgive me if I am not precise in my terminology) as it stalls after I get gas and try to start it up. I have to rev the engine to get it to stay on. I cannot stop after I get it started because it roughly idles and seems like it will shut back off if I do, which makes this a little dangerous as well as damaging for my car. I am distressed that my car is not included in this recall because I desperately need to repair it before I ruin my engine but I cannot because I don't have any money.
- Power train
I had the engine on 2018 (61000 mileage) focus replaced 1 and 1/2 year ago because of the oil pan wet belt recall. Now my transmission locked up because of clutch failure. I was lucky that I was coming to a stop while parking in my driveway. Now im told by mechanic that i need a new transmission. Why was ford allowed to continue selling cars with substandard engines.
- Fuel/propulsion system
Car doesn't start after putting in gas, has to revved to start. Leaking fluid on right front driver side. Car doesn't start in intervals throughout the day.
- Electrical system · Power train
Battery randomly died. When battery was replaced at the mechanic, it caused a glitch or broke something in or connected to the transmission. Car couldn’t reverse nor go faster than 1st gear. Had to drive 11 mph all the way to the Ford Dealership. Both Meineke AND Ford Service Manager said this is a…
Battery randomly died. When battery was replaced at the mechanic, it caused a glitch or broke something in or connected to the transmission. Car couldn’t reverse nor go faster than 1st gear. Had to drive 11 mph all the way to the Ford Dealership. Both Meineke AND Ford Service Manager said this is a KNOWN problem with Ford Focus’ and confirmed it is a common problem. I am now being quoted $10,000 to replace the transmission.
- Power train › Automatic transmission › Control module (tcm/pcm/tecm)
The contact owns a 2018 Ford Focus. The contact stated that upon starting the vehicle, the engine was idling roughly, and the vehicle jerked abnormally. The contact stated that the vehicle needed to be shifted into neutral in to be started. Upon shifting into reverse, the vehicle shut off, with…
The contact owns a 2018 Ford Focus. The contact stated that upon starting the vehicle, the engine was idling roughly, and the vehicle jerked abnormally. The contact stated that the vehicle needed to be shifted into neutral in to be started. Upon shifting into reverse, the vehicle shut off, with several unknown warning lights illuminated. The vehicle was towed to a dealer where it was diagnosed, and the contact was advised that the TCM was inoperable and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 63,451,
- Engine
at 72000 miles the vehicle stopped running no power no warning lights on indication of any issue. luckily it was on a side road. hade it towed to the ford dealer diagnosed with a broken timing belt and needed a new engine. the quote off $7000.00 to replace the engine with a new long…
at 72000 miles the vehicle stopped running no power no warning lights on indication of any issue. luckily it was on a side road. hade it towed to the ford dealer diagnosed with a broken timing belt and needed a new engine. the quote off $7000.00 to replace the engine with a new long block after paying the lone on the car I replaced the long block myself just last week on 07/20/2026 at a cost off around $5000.00
- Electrical system · Power train
I’ve had this car since 2021 and it’s been worked on 3 times for the same issues. My clutch and a couple other things for the transmission. I just recently had it worked on for transmission problems and paid $1100 for a belt replacement that didn’t even fix the issue. I told them it was clutch A…
I’ve had this car since 2021 and it’s been worked on 3 times for the same issues. My clutch and a couple other things for the transmission. I just recently had it worked on for transmission problems and paid $1100 for a belt replacement that didn’t even fix the issue. I told them it was clutch A like the code readers pulled (multiple times might I add) and they did a test and charged me for that test and said it was just the harness belt. Today my check engine light came on, and I had a code pulled and it was clutch A like I told them (P0902). I’ve had the actuator replaced at least twice and the power module has also been replaced. My cars engine light is on and it’s shifting hard and is taking a while to even shift. I have the invoices to show that each time it’s been worked on it’s been an issue with the transmission. My VIN number needs to be recalled before something worse happens. Each time it’s been worked on it costed me too much money especially to keep having the same problems. I’ve also done research that proves this particular issue is an issue with a lot of ford focus cars.
- Fuel system, gasoline
The contact owns a 2018 Ford Focus. The contact stated that the vehicle intermittently stalled with excessive fuel consumption. As a former Ford independent mechanic, the contact diagnosed the vehicle with a deformed fuel tank. The vehicle was taken to the dealer, where the canister purge valve was…
The contact owns a 2018 Ford Focus. The contact stated that the vehicle intermittently stalled with excessive fuel consumption. As a former Ford independent mechanic, the contact diagnosed the vehicle with a deformed fuel tank. The vehicle was taken to the dealer, where the canister purge valve was replaced under NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline); however, the manufacturer denied coverage for the fuel tank replacement. The contact stated that the failure reoccurred. No warning light was illuminated. The contact later received notification of NHTSA Campaign Number: 26V369000 (Fuel System, Gasoline), and the vehicle was taken to the dealer, where the canister purge valve was replaced a second time; however, the failure persisted. The dealer notified the manufacturer of the failure. The vehicle was not further repaired. The failure mileage was approximately 180,000.
- Engine · Power train
An authorized dealership performed a mandatory manufacturer safety recall repair on my vehicle for the Engine Oil Pump Belt and Tensioner (Ford Recall 23S64 / NHTSA Campaign 23V-905). While performing this specific recall, the initial facility negligently compromised the cooling system and created…
An authorized dealership performed a mandatory manufacturer safety recall repair on my vehicle for the Engine Oil Pump Belt and Tensioner (Ford Recall 23S64 / NHTSA Campaign 23V-905). While performing this specific recall, the initial facility negligently compromised the cooling system and created a severe leak, directly causing complete and total engine destruction. A subsequent independent diagnostic inspection by a separate authorized dealership confirmed this negligence. The vehicle became instantly disabled while driving, creating a severe road hazard. Total documented property damages are $14,448.31. Furthermore, the dealership and Ford Corporate have explicitly refused to repair the vehicle, despite Ford's dealer bulletins authorizing long-block engine replacements for failures related to this recall. They have also refused to reimburse me for the totaled vehicle or the out-of-pocket expenses incurred. Ford customer service has employed shady tactics, denying liability and stonewalling my attempts to reach a resolution, completely failing to provide the remedy mandated by this safety recall. The vehicle and all documentation are available for inspection upon request.
- Power train › Automatic transmission › Internal › Clutches/bands
The contact owns a 2018 Ford Focus. The contact stated that while driving at an undisclosed speed, the vehicle shuddered, and the transmission was not shifting properly while accelerating. There was no warning light illuminated. The vehicle was taken to a local dealer, where it was diagnosed with a…
The contact owns a 2018 Ford Focus. The contact stated that while driving at an undisclosed speed, the vehicle shuddered, and the transmission was not shifting properly while accelerating. There was no warning light illuminated. The vehicle was taken to a local dealer, where it was diagnosed with a clutch failure, and a clutch replacement was suggested at 27,000 miles. The vehicle was repaired under warranty. The contact stated that the shuddering persisted, and the purge valves were replaced after the clutch repair at 69,000 miles. The contact stated that on another occasion, while driving at an undisclosed speed, the vehicle shuddered and almost stalled. The vehicle was pulled over into a parking lot. The vehicle was driven back to the residence. The vehicle was taken back to the dealer, where it was diagnosed with a second clutch failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 86,000.
- Electrical system · Fuel/propulsion system
I am adding a major update to my safety recall complaint because this dealership just tried to pull an illegal financial ambush on me.After my 2019 Focus started stalling out on the highway right after they did Recall 18V735, I brought it back. I explicitly told them in writing on our text thread…
I am adding a major update to my safety recall complaint because this dealership just tried to pull an illegal financial ambush on me.After my 2019 Focus started stalling out on the highway right after they did Recall 18V735, I brought it back. I explicitly told them in writing on our text thread: 'I do not authorize any standard diagnostic fees, parts, or repair charges.' I just wanted them to show me proof that they didn't pinch a wire or glitch the software during the recall work.Instead of showing me proof, they sent me a text message today saying my vehicle was 'ready for pick up' just to lure me down to the lobby. When I got there, they slapped an unauthorized invoice for $988.82 in front of my face for parts and labor. They did nearly $1,000 worth of work after I told them 'no' in writing, clearly trying to quietly fix their botched recall mistake under the table and force me to pay for it.When I showed the advisor the texts proving I denied the charges, the staff panicked and couldn't answer who authorized the job. I refused to sign it or pay it, and I walked out. My car is currently stranded on their lot because they are holding my keys hostage over unauthorized bills on a federal safety recall file. I have already escalated this to Ford Corporate under Case # CXH-0831-1568-S8L7B8
- Engine · Fuel/propulsion system
Purge valve sensor and canister is malfunctioning causing my car to stall out
- Fuel/propulsion system
The plastic gas tank was warped by heat and a faulty purge solenoid. The warped gas tank is a known issue for the 2018 Ford Focus and other versions of the car are covered by the recall, but my VIN apparently was not despite experiencing the same issue at less than 50,000 miles. The warped gas tank caused a dangerous car shutoff in traffic.
- Power train
The ford focus I drive is constantly shuddering and having trouble selecting gears. The problem has been consistent since I bought the vehicle and I have read that this is a common issue with the ford focus transmission. I bought the vehicle for my sons first car and I can’t even let him drive it
- Electrical system · Fuel/propulsion system
The vehicle was serviced for NHTSA Recall 18V735 (Canister Purge Valve/Fuel Tank stalling hazard). Immediately upon pickup from the dealership, the vehicle began severely stumbling and stalling while driving on the highway. It died while driving on the street. The dealership's diagnostic paperwork…
The vehicle was serviced for NHTSA Recall 18V735 (Canister Purge Valve/Fuel Tank stalling hazard). Immediately upon pickup from the dealership, the vehicle began severely stumbling and stalling while driving on the highway. It died while driving on the street. The dealership's diagnostic paperwork confirmed an 'O2 sensor logic error causing the vehicle to stall' right after they performed the mandatory computer software flash and valve replacement. The dealership is refusing to verify if their technician damaged the adjacent wiring harness or glitched the software flash, leaving the vehicle an active highway stalling hazard. As for my experience, The car died in Clear Lake by Baybrook Mall. Extremely high traffic, almost got hit. (Yelled at by several drivers). Constant stalling happened in Baytown. Scariest incident was going over the very tall Fred Hartman bridge. My 10 year old daughter and I felt sure it was about to die and we were going to roll backward down the bridge becauseit kept dropping power. We took the ferry home because we were so scared.
- Engine
I had an oil pressure light come on while driving and it was followed by the car shutting off and not starting back up. It was towed to a mechanic who told me the timing belt broke while driving and the car requires a new engine. The car was the towed to a ford dealer who confirmed his diagnosis.…
I had an oil pressure light come on while driving and it was followed by the car shutting off and not starting back up. It was towed to a mechanic who told me the timing belt broke while driving and the car requires a new engine. The car was the towed to a ford dealer who confirmed his diagnosis. The car has the 1.0l ecoboost engine and manual transmission. I saw that there is an open investigation on this exact problem and a recall would be greatly appreciated. I'm shocked they are allowed to use a wet timing belt and not a chain.
- Engine
Last July my car was overheating and breaking down as I was driving on I4 to work one morning which it overheated and broke down which was the precursor the last time My engine blew in December 2024 which the engine was already repaired January 2022 (Dumphy Ford,Pa), December 2022 (Tropical Ford…
Last July my car was overheating and breaking down as I was driving on I4 to work one morning which it overheated and broke down which was the precursor the last time My engine blew in December 2024 which the engine was already repaired January 2022 (Dumphy Ford,Pa), December 2022 (Tropical Ford, Fl) then I got notices there is a recall with the oil pump and belt since February 2023 however the remedy parts were not available and kept getting notices that the parts would be in by fall 2024 then it kept getting pushed back when they would be available, meanwhile my car broke down again July 2024 which the engine needed to be replaced and was covered because oil and coolant was leaking into the engine due to the recall and they still didn’t have parts available and then car broke down again December 2024 which Tropical Ford covered because the recall parts were still not available. So in July 2025 they attempted to fix it and I picked it up and it overheated again and they kept it till September 2025 and fixed a bunch of things like transmission, recall and other things and now the car began to overheat again and took it to [XXX] and now they are saying the engine is blown again… I believe the recall failed and I shouldn’t have to pay for the 5Th engine replacement INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Power train · Unknown or other
The vehicle's transmission control module is not working. The Ford Focus vehicle put my family and I at risk because we would be driving along in the Ford vehicle then all of a sudden it would slow down abruptly in traffic as it loses power. We've only had the vehicle 7 years and it is one of the…
The vehicle's transmission control module is not working. The Ford Focus vehicle put my family and I at risk because we would be driving along in the Ford vehicle then all of a sudden it would slow down abruptly in traffic as it loses power. We've only had the vehicle 7 years and it is one of the most expensive problems to have with the car. Many reports online state that transmission control modules and transmissions in general are known complaints for 2018 Ford Focus cars. A diagnostic was performed by a Ford dealer's service center. It was determined the part needs to be replaced. This is very dangerous. I would like for this to be repaired without causing any additional expenses to my family as the Ford company is aware that more than few models have this problem before reaching 7 years or 100,000 miles
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Timing Belt Failure
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles).…
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Timing Belt Failure
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles).…
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Oil Pump Failure
On September 20, 2023, the Office of Defects Investigation (ODI) opened PE23-015 to investigate instances of engine failure due to loss of oil pressure in model year (MY) 2018-2021 Ford EcoSport vehicles. Some consumers reported a low engine oil pressure warning lamp immediately preceding a complete loss or reduction…
On September 20, 2023, the Office of Defects Investigation (ODI) opened PE23-015 to investigate instances of engine failure due to loss of oil pressure in model year (MY) 2018-2021 Ford EcoSport vehicles. Some consumers reported a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle was in motion. The investigation revealed that the engine oil pump drive belt tensioner arm may fracture, separate from the tensioner backing plate, and/or the oil pump drive belt may degrade and lose teeth, resulting in a loss of engine oil pressure. A loss of engine oil pressure can result in engine seizure, which can result in a loss of motive power and a loss of mechanical vacuum pump required to provide power braking assist, increase the risk of a crash. On December 22, 2023, Ford filed recall 23V-905 for certain MY 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The recall remedy provides the replacement of the oil pump drive belt tensioner assembly and oil pump drive belt with redesigned parts to improve robustness. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Loss of Motive Power
On September 15, 2023, the Office of Defect Investigation (ODI) opened this Recall Query (RQ) after receiving 98 consumer complaints alleging loss of motive power in model year (MY) 2012-2018 Ford Focus vehicles. The RQ focused on the effectiveness of the remedies of Recall 18V-735 and 19V-515. In October 2018, Ford…
On September 15, 2023, the Office of Defect Investigation (ODI) opened this Recall Query (RQ) after receiving 98 consumer complaints alleging loss of motive power in model year (MY) 2012-2018 Ford Focus vehicles. The RQ focused on the effectiveness of the remedies of Recall 18V-735 and 19V-515. In October 2018, Ford issued Recall 18V-735, which updated Powertrain Control Module (PCM) software in MY 2012-2018 Ford Focus vehicles equipped with 2.0L GDI engines built prior to April 13, 2017, and those with 2.0L GTDI engines built prior to February 2, 2018. The recall addressed vehicles experiencing a malfunctioning Canister Purge Valve (CPV) that can stick open and PCM software that does not adequately detect a stuck-open CPV condition. A CPV that is stuck open can cause excessive vacuum in the fuel vapor management system, potentially deforming the fuel tank, collapsing on itself. This deformation of the fuel tank can cause a Malfunction Indicator Light (MIL) to illuminate, an inaccurate or erratic fuel gauge indication, drivability issues, and/or loss of motive power. In July 2019, Ford issued Recall 19V-515, which addressed certain MY 2012 and MY 2017 Ford Focus vehicles equipped with 2.0L GDI and MY 2013-2014 Ford Focus vehicles equipped with 2.0L GTDI engines whose PCM software had been reprogrammed as a part of recall 18V-735. The updated software calibrations for these subject vehicles were not properly installed by Ford at the time of production. Approximately one year after this RQ was opened, on September 25, 2024, Ford initiated a customer satisfaction program (24N07) for MY 2012-2018 Ford Focus vehicles equipped with the 2.0L GDI and GTDI engines to—as ODI learned during this investigation—address a different issue with the CPV from the primary focus of the safety recalls (18V-735 and 19V-515). Ford stated the CPV may not operate as intended in these vehicles. A failed CPV on its own merit, may cause drivability concerns such as engine hesitation, running rough, or stalling at low speed, which will be accompanied by an illuminated MIL. This program provides a one-time replacement of the CPV for vehicles with 15 years of service or less (with no mileage restriction). This coverage will automatically transfer to subsequent owners. It is to be noted that the customer satisfaction program being taken by Ford to address this RQ investigation results in a much different and significantly less severe problem than the safety action taken to remedy 18V-735 and 19V-515. ODI found no further issues with the combined scope and severity related to 18V-735 and 19V-515 therefore, ODI is closing this Recall Query. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Pedestrian alert sounds
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11008948While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
- 11001174This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10251952For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
- 10240743The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
- 10235323Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit REASON FOR THIS SUPPLEMENT Program Terms & Urgency / Expiration Date: Program extension until July 31, 2023. Service Action: o IDS level 128 or higher is now required to address various programming issues encountered. o C-MAX Energi vehicles are now serviceable with new software and hardware. Labor Allowances: C-MAX labor has been updated. Parts Requirements / Ordering Information: o The C-MAX 4G Upgrade Kit is now orderable at this time with a new part number. o MKX Rear seat backrest nut claim quantity updated. Technical Information updates: o Ensure IDS level 128 or higher is used. o Toggling Valet Mode is no longer required. o C-MAX Energi instructions are now available. Owner Notification: Non-repaired vehicle owners will be mailed the week of April 17, 2023. Pickup and Delivery: Added Customer Acknowledgement Form - Review form contents with customer prior to kit ordering and obtain customer signature prior to installation for Focus BEV, C-MAX, and Fusion Energi vehicles.
- 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
- 10218617Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
- 10217028Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
- 10214758Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
- 10211709Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
- 10209209This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
- 10208146Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
- 10205694Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
- 10203848Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
- 10201050Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10201013Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
- 10199536Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
- 10198663Some 2016-2018 Focus and 2018-2019 EcoSport vehicles equipped with a 1.0L EcoBoost engine, 6F15 automatic transmission and built on or before 3-Jul-2019 may exhibit an illuminated oil pressure warning lamp with a loss of engine oil pressure. This may be due to a failed engine oil pump belt tensioner. If engine oil pressure at idle is below 10 psi (refer to Section 303-00 in the Workshop Manual for the oil pressure test procedure) and/or metal contamination is present in the engine oil, replace the engine assembly with a long block option 6006 and the turbocharger.
- 10198605Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
- 10198600Some 2016-2018 Focus and 2018-2019 EcoSport vehicles equipped with a 1.0L EcoBoost engine, 6F15 automatic transmission and built on or before 3-Jul-2019 may exhibit an illuminated oil pressure warning lamp with a loss of engine oil pressure. This may be due to a failed engine oil pump belt tensioner which leads to a loss of engine oil pressure. If engine oil pressure at idle is below 10 psi (refer to Section 303-00 in the Workshop Manual for the oil pressure test procedure) and/or metal contamination is present in the engine oil, no further diagnostics should be performed. Replace the engine assembly with a long block option 6006 to correct this condition.
- 10194428Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 101944152015-2018 Focus service parts transmissions part # F1FP-7000-VB / F1FZ-7000-P built on 1-Aug-2020 and through 01-Mar-2021 may have an incorrect input speed sensor A (ISSA) shim thickness. This may cause an intermittent input speed sensor diagnostic trouble code (DTC). In the event of shift issues or skip shift events, check and verify that the ISSA speed sensor shim is 2.0 mm (0.079 in) F1FZ-7Z101-A before proceeding with further diagnostics.
- 10191099Some 2018 Focus, 2019 Fiesta, 2019-2020 Transit and 2019-2020 Transit Connect vehicles may exhibit a concern where the radio randomly seeks through FM stations when a Bluetooth device is connected and streaming audio. Engineering is currently working on a solution for this condition. Inform customers that Ford is developing a software fix that is expected in May 2021. In the interim, let the customer know that the radio will still function without Bluetooth and schedule a follow-up appointment with the customer for late February. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
- 10191089Some 2016-2018 Focus and 2018-2019 EcoSport vehicles equipped with a 1.0L EcoBoost engine, 6F15 automatic transmission and built on or before 3-Jul-2019, may exhibit an illuminated oil pressure warning lamp with a loss of engine oil pressure. This may be due to a failed engine oil pump belt tensioner which leads to a loss of engine oil pressure. If engine oil pressure at idle is below 10 psi and/or metal contamination is present in the engine oil, no further diagnostics should be performed. Replace the engine assembly to correct this condition.
- 10187930Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
- 10184640Some 2018 Focus, 2019 Fiesta, 2019-2020 Transit, 2019-2020 Transit Connect, and 2020 EcoSport vehicles may exhibit a concern where the radio randomly seeks through FM stations when a Bluetooth device is connected and streaming audio. Engineering is currently working on a solution for this condition. Inform customers that Ford is developing a software fix that is expected in February 2021. In the interim, let the customer know that the radio will still function without Bluetooth and schedule a follow-up appointment with the customer for late February. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
- 10181913Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
- 10180428Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
- 10179356Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10179117Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
- 10177042Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
- 10177038Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10176123Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
- 10175895Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
- 10174421Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
- 10172972SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
- 10170911Some 2012-2018 Focus Electric vehicles may exhibit a Stop Safely Now message displayed in the instrument panel cluster (IPC) message center. This may be due to either an internal coolant leak on the upper or lower high voltage battery or corrosion on the lower high voltage battery connector caused by water ingress. If this occurs, the vehicle may not restart once it has been shut off. To resolve the condition, follow the Service Procedure to replace the upper and lower high voltage battery or apply corrosive protection.
- 10169986Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10168810Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
Every Ford Focus model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.