2013 Ford Fusion Hybrid
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Ford › Fusion Hybrid › 2013
These records cover every 2013 Ford Fusion Hybrid. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2013 Ford Fusion Hybrid. Newest first.
Ford Motor Company (Ford) is recalling certain 120V Convenience charge cords that were supplied with and sold for use with 2013-2015 Ford C-Max Energi and Fusion Energi vehicles and 2012-2015 Ford Focus Electric vehicles. Cords with part numbers FM58-10B706-AA, FM58-10B706-AB, FM58-10B706-AC, FM58-10B706-AD, FM58-10B706-AE and FM58-10B706-AF were…
Risk and remedy
Risk
An overheated cord can increase the risk of a fire.
Remedy
Ford will notify owners, and dealers will replace the current cord with a new 120V convenience cord with a thermistor, free of charge. The recall began January 18, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S24.
Owner complaints
126 complaints1 involved a crash4 involved a fire1 injuries
What owners report most
Latest complaints
- Power train
The contact owns a 2013 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle failed to respond normally while depressing the brake pedal. Several unknown warning lights were illuminated during the failure. The failure caused the steering wheel to lock up, the…
The contact owns a 2013 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle failed to respond normally while depressing the brake pedal. Several unknown warning lights were illuminated during the failure. The failure caused the steering wheel to lock up, the brake pedal became extremely firm, and the accelerator pedal became inoperable. Additionally, the exterior lights shut off unexpectedly and the vehicle lost electrical power. The vehicle was safely pulled into a parking lot, and the contact waited for several minutes before restarting the vehicle. The vehicle was restarted; however, 30 seconds after resuming driving the vehicle shut off again. The vehicle was towed to a Ford dealer; however, the mechanics were unable to duplicate the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 179,000.
- Lane departure › Assist · Lane departure › Warning · Steering
While driving a 2013 Ford Fusion Hybrid Titanium (approximately 157,000 miles), the Electronic Power-Assisted Steering (EPAS) system suddenly failed without warning during heavy rain in Philadelphia, PA. I was driving near the riverfront area by [XXX] when the steering immediately became extremely…
While driving a 2013 Ford Fusion Hybrid Titanium (approximately 157,000 miles), the Electronic Power-Assisted Steering (EPAS) system suddenly failed without warning during heavy rain in Philadelphia, PA. I was driving near the riverfront area by [XXX] when the steering immediately became extremely stiff and difficult to turn. No prior warning lights or steering-related symptoms were present before the failure. Due to wet road conditions and the sudden loss of steering assist, I temporarily lost the ability to maneuver the vehicle normally and nearly collided with roadside structures near the river. Considerable physical force was required to maintain directional control and safely move the vehicle. This created an immediate safety hazard to myself and nearby traffic. The vehicle has not been involved in a crash, but the failure created a near-miss situation. My VIN currently shows no open recall for this issue, despite similar steering-system failures reported in comparable Ford vehicles using EPAS. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system · Unknown or other
The factory-installed rearview backup camera on my 2013 Ford Fusion fails intermittently. When shifting into reverse, the display screen frequently goes black, shows a distorted or flickering image with multicolored lines, or displays an error message stating the camera is unavailable. The failure…
The factory-installed rearview backup camera on my 2013 Ford Fusion fails intermittently. When shifting into reverse, the display screen frequently goes black, shows a distorted or flickering image with multicolored lines, or displays an error message stating the camera is unavailable. The failure is unpredictable but occurs more often in hot weather or after rain, suggesting a hardware defect. The component that has failed is the rearview camera system, likely the camera module itself, which is available for inspection. This malfunction creates a significant safety hazard by eliminating rear visibility, substantially increasing the risk of a back-over collision with pedestrians, children, or other objects. The failure to display a rearview image is a non-compliance with Federal Motor Vehicle Safety Standard No. 111. The problem has not been confirmed by a dealer due to its intermittent nature, making it difficult to reproduce on demand. The vehicle has not been inspected by the manufacturer or other parties regarding this issue. The symptoms first appeared several months ago and have become progressively more frequent. The primary warnings are the on-screen error messages and the loss of the video feed itself.
- Electrical system · Fuel system, gasoline
The contact's granddaughter owned a 2013 Ford Fusion Hybrid. The contact stated that while her granddaughter was driving at an undisclosed speed, the driver looked in the rearview mirror and noticed black smoke coming from the rear seats of the vehicle. The contact stated that the driver's sons…
The contact's granddaughter owned a 2013 Ford Fusion Hybrid. The contact stated that while her granddaughter was driving at an undisclosed speed, the driver looked in the rearview mirror and noticed black smoke coming from the rear seats of the vehicle. The contact stated that the driver's sons were in car seats in the rear seats of the vehicle. The driver immediately pulled over to the side of the road, exited the vehicle, and took her sons out of the vehicle. The contact stated that the entire vehicle then caught on fire. The contact stated that the driver's side of the vehicle was more burned than the rest of the vehicle. The fire was extinguished by the Fire Department, who informed the contact's granddaughter that the fire might have originated from the trunk of the vehicle. It was unknown whether a Police report or a Fire Department report was filed. The contact stated that the vehicle was towed and could be totaled. The driver's mother transported the driver and her sons to the emergency room due to smoke inhalation. It was unknown whether injuries were sustained. The dealer and the manufacturer were not notified of the failure. The failure mileage was unknown.
- Power train
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving 65 MPH and approaching a stop, the vehicle jerked forward. The contact veered to the right to avoid crashing with another vehicle. No warning light was illuminated. The local dealer was contacted, and the vehicle was taken…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving 65 MPH and approaching a stop, the vehicle jerked forward. The contact veered to the right to avoid crashing with another vehicle. No warning light was illuminated. The local dealer was contacted, and the vehicle was taken to the dealer and was diagnosed with transmission failure. The contact stated that the vehicle was repaired under an unknown related recall. The contact stated that the failure persisted. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 95,189.
- Steering · Traction control system
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, he became aware that the electronic power steering was not functioning properly, requiring increased effort to maneuver the vehicle. The traction control and power steering assist warning lights…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, he became aware that the electronic power steering was not functioning properly, requiring increased effort to maneuver the vehicle. The traction control and power steering assist warning lights were illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with the electronic power steering gear motor. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V632000 (Steering), but the VIN was not included. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 112,000.
- Steering
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that while her mother was driving at an undisclosed speed, she became aware that the electronic power steering was not functioning properly, requiring increased effort to maneuver the vehicle. The steering assist warning light was…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that while her mother was driving at an undisclosed speed, she became aware that the electronic power steering was not functioning properly, requiring increased effort to maneuver the vehicle. The steering assist warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V632000 (Steering) but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 125,000.
- Power train
The contact owns a 2013 Ford Fusion. The contact stated that when the vehicle was turned on, the contact heard a loud sound emanating from the engine compartment. On another occasion, while driving at various speeds, the vehicle started shaking. Additionally, when the vehicle was in the park(P)…
The contact owns a 2013 Ford Fusion. The contact stated that when the vehicle was turned on, the contact heard a loud sound emanating from the engine compartment. On another occasion, while driving at various speeds, the vehicle started shaking. Additionally, when the vehicle was in the park(P) position the vehicle continued to move inadvertently. The parking brake was applied to stop the vehicle. The vehicle was taken to a dealer where it was diagnosed that the loud noise was from the shifting from the hybrid to gasoline and that the bushing bearings and transmission needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 130,000.
- Electrical system · Latches/locks/linkages · Power train
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that while sitting in the passenger seat as their husband was driving through a fast food drive-through and attempting to make a left turn the power steering suddenly failed. The dashboard was illuminated with several different lights…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that while sitting in the passenger seat as their husband was driving through a fast food drive-through and attempting to make a left turn the power steering suddenly failed. The dashboard was illuminated with several different lights, meanings unknown, however, there were no warning lights before the failure occurred. The driver had used an excessive amount of force to pull to the side where he turned the vehicle off and then restarted it to regain proper function. The failure persisted. The vehicle was taken to an independent mechanic where it was diagnosed that the electrical power assist system failed. The independent mechanic informed them that the failure was related to NHTSA Campaign Number: 15V250000 (Steering) and referred them to Ford. The dealer was contacted and informed that the VIN was not included in the NHTSA Campaign Number: 15V250000 (Steering) but was included in NHTSA Campaign Numbers: 22V413000 (Power Train) and 20V331000 (Locks, Latches ) . The vehicle had not been repaired. The manufacturer was made aware of the failure and confirmed the VIN was not included in NHTSA Campaign Number: 15V250000 (Steering) then referred them to NHTSA. The approximate failure mileage was unknown.
- Power train
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that while driving at various speeds, an abnormal whining sound coming from the vehicle with the check engine warning light illuminated. The contact also stated that while refueling the vehicle, fuel would spew back out of the tank. As…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that while driving at various speeds, an abnormal whining sound coming from the vehicle with the check engine warning light illuminated. The contact also stated that while refueling the vehicle, fuel would spew back out of the tank. As both failures persisted, the vehicle began to jerk and hesitate upon the depression of the accelerator pedal. The contact attempted to make an appointment with the dealer but was informed that due to a shortage of employees, the vehicle could not be serviced for months. The contact stated that while waiting for the appointment while driving at an undisclosed speed, the vehicle stalled upon depression of the accelerator pedal while at a complete stop. The "Stop Safely Now" message was displayed on the instrument panel. The vehicle was towed to the dealer and diagnosed with a defective purge valve which caused the transmission failure. The contact then received notification of NHTSA Campaign Number: 22V413000 (Power Train). The dealer and the manufacturer were notified of the issue and informed the contact that the recall was not related to the transmission failure. The vehicle was not repaired and remained in the possession of the dealer. The failure mileage was approximately 130,000.
- Electrical system
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that the brake lights remained illuminated whether the vehicle was running or turned off. Due to the failure, the contact had to jumpstart the vehicle due to the battery being drained. The contact had taken the vehicle to the dealer…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that the brake lights remained illuminated whether the vehicle was running or turned off. Due to the failure, the contact had to jumpstart the vehicle due to the battery being drained. The contact had taken the vehicle to the dealer where she was provided an estimate for the repair. Upon investigation, the contact discovered recalls on the 2014 and 2015 model year vehicles for the failure. The manufacturer was notified of the failure and referred her to the NHTSA for assistance. The vehicle was not repaired. The failure mileage was approximately 159,000.
- Power train › Automatic transmission
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving approximately 30 MPH and slowing down to enter a parking lot, as she slowed the vehicle, it would not respond to the shift lever, and as she stopped and tried to shift the vehicle to park, the shift lever stopped…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving approximately 30 MPH and slowing down to enter a parking lot, as she slowed the vehicle, it would not respond to the shift lever, and as she stopped and tried to shift the vehicle to park, the shift lever stopped responding. The contact stated no warning light was illuminated. The contact turned off the vehicle and called for a towing service and had it taken to a dealer who diagnosed that the transmission shifting cable needed to be replaced. The vehicle was repaired, however, the failure recurred. The vehicle was towed to the contact's residence and had not been repaired. The manufacturer had not been informed of the failure. The failure mileage was approximately 180,000.
- Power train
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving 35-40 MPH, she heard abnormal grinding sounds coming from the driver's side front wheel. The contact was able to continue driving. The vehicle was taken to an independent mechanic where the ball joint and unknown…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving 35-40 MPH, she heard abnormal grinding sounds coming from the driver's side front wheel. The contact was able to continue driving. The vehicle was taken to an independent mechanic where the ball joint and unknown suspension parts were replaced; however, the failure reoccurred. The vehicle was taken back to the independent mechanic who referred the contact to a certified transmission specialist. The vehicle was taken to a certified transmission specialist and was then towed to a second certified transmission specialist. Both transmission specialists diagnosed that the bushings were grinding in the transmission. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that they could not assist as the parts for NHTSA Campaign Number: 22V413000 (Power Train) were not yet available. The failure mileage was approximately 136,000.
- Seat belts
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that the driver’s side seat belt retractor failed to extend. The contact stated no warning light was illuminated. The contact called the local dealer and made them aware of the failure. The vehicle was not diagnosed or repaired. Upon…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that the driver’s side seat belt retractor failed to extend. The contact stated no warning light was illuminated. The contact called the local dealer and made them aware of the failure. The vehicle was not diagnosed or repaired. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 16V875000 (Seat Belts) however, the VIN was not included. The manufacturer had been informed of the failure. The failure mileage was approximately 45,000.
- Power train
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that the vehicle failed to shift out of gear. There were no warning lights illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and the contact was…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated that the vehicle failed to shift out of gear. There were no warning lights illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and the contact was referred to the NHTSA for assistance. The contact stated the failure was related to NHTSA Campaign Number: 19V362000 (Power Train). The approximate failure mileage was 135,000.
- Power train · Power train › Automatic transmission › Lever and linkage › Floor shift
The contact owns a 2013 Ford Fusion. The contact stated that while attempting to park, the vehicle became stuck in the reverse position while shifting into the drive position. The contact applied the emergency brakes to prevent the vehicle from reversing. The vehicle was not diagnosed or repaired.…
The contact owns a 2013 Ford Fusion. The contact stated that while attempting to park, the vehicle became stuck in the reverse position while shifting into the drive position. The contact applied the emergency brakes to prevent the vehicle from reversing. The vehicle was not diagnosed or repaired. The contact referenced NHTSA Campaign Number: 18V471000 (power train) however the recall was not associated with the VIN. The manufacturer was made aware of the failure. The failure mileage was approximately 75,000.
- Unknown or other
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, the steering wheel became difficult to turn. The contact stated there was no warning light illuminated. The vehicle was towed to a local dealer where it was diagnosed with needing the steering…
The contact owns a 2013 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, the steering wheel became difficult to turn. The contact stated there was no warning light illuminated. The vehicle was towed to a local dealer where it was diagnosed with needing the steering assembly replaced. The vehicle was not repaired. The manufacturer was informed of the failure and informed the contact that the VIN was not under recall. The failure mileage was approximately 90,000.
- Power train
TL* the contact owns 2013 ford fusion hybrid. The contact stated while vehicle was at a stand still, the contact attempted to restart vehicle, however the vehicle failed to restart twice. The contact stated the power train warning light was illuminated. The vehicle restarted after the third…
TL* the contact owns 2013 ford fusion hybrid. The contact stated while vehicle was at a stand still, the contact attempted to restart vehicle, however the vehicle failed to restart twice. The contact stated the power train warning light was illuminated. The vehicle restarted after the third attempt. The contact stated the failure related to nhtsa campaign number: 18v169000 (power train). The vehicle was not taken to the dealer. The vehicle was not diagnosed nor repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 48,700.
- Power train
Hello. I just buy car and after two day coming some noise from engine mechanic tel me this IS transmission. So also he told me 95% of ford fusion hybrid 2013-2014 have a same problem. I think ford have to recall. *tr
- Power train
TL* the contact owns a 2013 ford fusion hybrid. After an alignment was performed on the vehicle, the contact heard an abnormal noise and the vehicle shook while driving various speeds. When the contact slowed down, he heard a loud humming noise. There were no warning indicators illuminated. The…
TL* the contact owns a 2013 ford fusion hybrid. After an alignment was performed on the vehicle, the contact heard an abnormal noise and the vehicle shook while driving various speeds. When the contact slowed down, he heard a loud humming noise. There were no warning indicators illuminated. The vehicle was taken to bartow ford (located at 2800 US-98, bartow, fl 33830, (800) 301-8570) where it was diagnosed that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was not notified. The failure mileage was 112,000.
- Power train · Structure › Body
While coming off of an exit my right front passenger door flew open and I was almost in an accident because it frightened me as another car behind me had to brake as well to avoid hitting me from the back. I read up on this car and there IS information statin the there are problems with the door…
While coming off of an exit my right front passenger door flew open and I was almost in an accident because it frightened me as another car behind me had to brake as well to avoid hitting me from the back. I read up on this car and there IS information statin the there are problems with the door lock/latches where you think your door IS lock and it IS not. Now I try yo close it, the door will not lock at all. I did not see a recall on my vin but I not have to contact ford because there IS information all over the internet stating that IS a know fact to happen on the 2013 and I believe the 2014 models. I also have an issue where the sync with my ford does not work correctly. I am unable to use touchscreen because when I due I get an error message pops up on the screen saying something about the usb and power source and does not allow me to do anything else. I literally have to turn off and restart my screen.
- Service brakes
Periodically when apply brake, no engagement, as if I hit a patch of ice, then the break engages.
- Engine
I was driving myself to my emt salary, full benefit job when my car began to smoke. When I pulled over and lifted the hood flames came roaring out. I personally was able to put it out being a former fire fighter. Now insurance says they can not cover this due to it being an engine failure. Despite…
I was driving myself to my emt salary, full benefit job when my car began to smoke. When I pulled over and lifted the hood flames came roaring out. I personally was able to put it out being a former fire fighter. Now insurance says they can not cover this due to it being an engine failure. Despite full coverage, gap insurance, and fire casualty insurance they could not pay out for a new engine. Only the fire damage done under the hood and nothing else. The dealership explained I needed an entirely new engine put in and that it would cost 7,000.00. I had this car less then 6 months when it caught fire. I also have 11,000.00+ loan out on this car. I filed a claim with ford motor and they have ignored all my attempts. I am unable to get another loan due to already having an open car loan and not enough credit. I lost my job as a result to not being able to afford a rental after blowing through my entire savings for one. I temporarily lost custody of my son due to not transportation to his school. I lost my home due to not having my full time job anymore. I am nearing the point of living on the streets. I lost my emotional support animal due to having no home. Please help a single mother come back from such a loss. *js
- Electronic stability control (esc) · Steering
Loss of power steering while driving, barely able to keep control as it happened mid turn and had to steer away from curb as the steering wheel was mostly locked up. error codes including steering assist fault, advanced track fault, and hiii start fault appeared and steering wheel stayed locked up. attempted turning vehicle off and on but errors and steering wheel failure remain.
- Seat belts · Seats
When I put the back seats down to carry items the back seat will not go back in place. You have to take the bottom seat out and remove the center seatbelt bolt which IS attached to the frame and release the pressure once you do this the returns to a normal position it IS a safety issue. The middle seat belt retractor seems defective. It was stationary
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Pedestrian alert sounds
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
- Front Brake Jounce Hose Failures
On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the…
On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturing on certain MY 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The result causes a brake fluid leak, lengthening the distance needing to stop the vehicle, increasing the risk of a crash.On March 10, 2023, Ford Motor Company (Ford) submitted to NHTSA Safety Recall 23V-162 (Ford Recall 23S12) to address front brake jounce hoses that may rupture. Ford found the rupture occurs from a localized failure of the internal reinforcement braid due to cyclic fatigue through tensile/bending and torsional inputs during suspension and steering articulations. The supplier for the front brake jounce hoses is Hitachi. This recall affects the subject vehicles equipped with non-hybrid engines and the suspect front brake jounce hoses (a total of 1,280,726 vehicles). The recall covers subject vehicles built from February 3, 2012 to July 19, 2017 when the suspect hoses were used in vehicle production. The remedy is for dealerships to replace both front brake jounce hoses with new hoses that have a revised braid material at no cost. The vehicles equipped with hybrid engines are excluded from the recall because the internal hose pressure is much lower due to the regenerative braking provided by the hybrid brake system. No failures of brake hoses on hybrid vehicles have been reported to ODI or Ford.Ford's actions address ODIs concerns at this time. Hybrid vehicles will be monitored for related failures. The agency reserves the right to take further action if warranted by new circumstances.The 103 ODI numbers cited above can be viewed at NHTSA.gov under the following ID numbers:11511014, 11510867, 11510318, 11509030, 11505993, 11504989, 11504400, 11502147, 11502082, 11501820, 11501283, 11498439, 11498296, 11496842, 11496335, 11494931, 11494851, 11494252, 11493001, 11492084, 11492070, 11491444, 11491274, 11488858, 11488027, 11487627, 11487416, 11487233, 11486150, 11484924, 11484526, 11484080, 11483948, 11483926, 11483739, 11483723, 11482773, 11482690, 11481077, 11480788, 11480294, 11480052, 11479338, 11479334, 11479252, 11479247, 11479187, 11479094, 11479048, 11478985, 11478953, 11478729, 11478216, 11476892, 11476282, 11470558, 11468994, 11467109, 11466294, 11462746, 11461217, 11456065, 11455367, 11444848, 11436419, 11436376, 11430685, 11428329, 11425083, 11421026, 11420738, 11420735, 11420298, 11418197, 11403926, 11397549, 11366991, 11366757, 11361016, 11359968, 11354569, 11352165, 11350344, 11348799, 11343929, 11343205, 11331947, 11329020, 11319596, 11310529, 11292271, 11288455, 11254787, 11253479, 11253244, 11234622, 11230669, 11230050, 11228240, 11221111, 11143630, 11129392 and 11120228.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Door Latch Failures
In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs…
In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs reported the failure occurred after the latch had been remedied under a prior recall which involved fracture of the latch pawl spring tab due to thermally induced cyclic fatigue. Other VOQs alleged a similar failure in vehicles not previously recalled. A latch with a fractured pawl spring tab typically results in a ?door will not close? condition, however in certain somewhat rare circumstances, may result in the door coming open while driving. In response to ODI?s investigation, Ford has announced three field actions, as discussed below.On March 23, 2020, Ford submitted Safety Recall 20V-177 (Ford 20S15), a regional recall campaign to address door latch failures in vehicles not previously recalled under Safety Recalls 15V-246, 16V-643 and 17V-210. The recall affects vehicles currently or ever registered in certain high ambient temperature states (see 20V-177 for affected states). As a remedy, Ford will replace all four door latches free of charge.On August 24, 2020, Ford issued a non-safety regional field action (Ford 20R01) to address door latch failures on the same model/MY vehicles not covered under 20V-177 (i.e., not currently/ever registered in affected states). According to Ford, spring tab failure rates for vehicles covered by this action are about half that of the 20V-177 vehicles. Under this action, dealers will replace all door latches, free of charge, if either; a) the vehicle exhibits a related latch concern, or b) if the vehicle owner expresses a concern about the latches in their vehicles. Details can be found under NHTSA TSB No. 10190990, a copy of which is available in this investigative file available at NHTSA.gov.On June 8, 2020, Ford submitted Safety Recall 20V-331 (Ford 20S30) addressing vehicles previously remedied under NHTSA Recalls 15V-246, 16V-643 and 17V-210, where the repair may not have been properly completed, specifically not all of the door latches were replaced, or replaced correctly. This recall involves an inspection of the latches, with the option for a consumer self-inspection; owners could view the date codes on their latches (and confirm child safety locks are present on the rear doors) and then submit the information to Ford?s mobile app or website. A dealership inspection option was also available. Any vehicle found to have unreplaced defective latches requires the replacement of all door latches as directed by Ford.Regarding the 4,494 reports cited above, 1,485 involve scope-related failures (with 13% alleging door opening), and the remaining 3,009 reports involving remedy concerns (with 18% alleging door opening - note ODI was unable to verify the allegations of door opening). The three ODI injuries were all relatively minor. Ford?s reported injury incidences include one (unconfirmed) report of an ejection, three minor injuries with the others involving undisclosed injuries. Ford?s crashes involved two (unconfirmed) crashes alleging the incident door contacted another vehicle and three involving doors striking other property.The recalled vehicles include MY 2011-2015 Ford Fiesta, 2013-2016 Ford Fusion and Lincoln MKZ, 2015 Ford Mustang and Lincoln MKC, 2013-2015 Ford Escape and Ford C-MAX, 2012-2015 Ford Focus and 2014-2016 Ford Transit Connect.Ford's actions address ODI's concerns at this time. ODI will take further action if warranted by new information. The reference (OD
- Door Latch Failure
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of doors failing to latch and/or inadvertently opening on model year (MY) 2011-2013 Ford Fiesta, MY 2013 Ford Fusion and MY 2013 Lincoln MKZ vehicles. All of the affected vehicles share the same door latch design.ODI has…
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of doors failing to latch and/or inadvertently opening on model year (MY) 2011-2013 Ford Fiesta, MY 2013 Ford Fusion and MY 2013 Lincoln MKZ vehicles. All of the affected vehicles share the same door latch design.ODI has received 281 unique reports related to the alleged problem, with over 100 claiming that the door(s) opened inadvertently while the vehicle was in motion. There were no crashes reported however three separate injuries were indicated, all caused by a rebounding door striking a consumer after they attempted to close it. In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 1,102 unique reports related to the alleged problem. There were no injury claims but there were two claims of low speed accidents occurring involving the door opening while driving and damaging property. Ford also submitted 10,883 warranty claims related to door latch failures.Many customers indicated that the door would not latch at all and accordingly they decided to restrain the door by other means (looping the seatbelt through the door, or using rope or tape) in order to drive the vehicle.Some customers also reported multiple door latch failures occurring on the same vehicle on different doors occurring months apart.On April 23rd, 2015 Ford notified ODI that it would conduct a safety recall (15V-246) to remedy door latches failures on certain MY 2011-2014 Ford Fiesta and MY 2013-2014 Ford Fusion and Lincoln MKZ vehicles.According to Ford, the pawl spring tab located within the door latch can break off, or separate and result in a ?door will not close condition.The recalled vehicles include Fiesta vehiclesmanufactured from the start of the MY 2011 to May 2013 and Fusion and MKZ vehicles manufactured from the start of the MY 2013 year until May 2013.In May 2013 Ford reports that it made a manufacturing quality control change, specific to the spring tab, to improve the performance of the existing part.The door latch spring tab was redesigned and the new latch was phased into production in December 2014 with a new part number.Ford will replace all four door latches on the affected vehicles with the new latch design currently in production.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
- 10228876Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
- 10226752Some 2013-2016 Escape/Fusion/MKZ vehicles may display an error message when updating the All Wheel Drive-ATC Barcode using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing.
- 10225458Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
- 10222788Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
- 10218617Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
- 10214758Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
- 10212957Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
- 10211728Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
- 10210730Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
- 10209209This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
- 10204994Online automotive service information system for March 2016
- 10203850Various 2012-2015 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed.
- 10201034Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
- 10199536Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
- 10194434Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
- 10189767Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
- 10181933This article supersedes 17-2225 to update the vehicle model years affected and Service Procedure. Some 2013-2014 Fusion and 2013-2020 MKZ vehicles may exhibit unintended exterior mirror movement in wet weather conditions. This may be due to water intrusion into the exterior mirror connector. To correct the condition, follow the Service Procedure steps to remove the 16 pin connector and install two weather tight 8 pin connectors.
- 10180428Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
- 10177863This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
- 10177123Some 2013-2016 Fusion/MKZ/C-MAX vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.
- 10176123Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
- 10175895Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
- 101719622013-2018 C-Max, 2013-2020 Fusion Hybrid/MKZ Hybrid vehicles may exhibit a MIL with Diagnostic Trouble Code (DTC) P0340 and/or P0344. This may occur due to excessive moisture build up in the engine oil. Excess moisture occurs when the vehicle is driven short distances and/or less than 6,000 combined miles per year. To correct the condition, replace the camshaft position sensor (CMP) and change the engine oil. Advise the customer to perform more frequent oil changes and allow the internal combustion engine to reach operating temperature when running to prevent reoccurrence. Refer to the owners guide - maintenance - engine oil check - operating in cold climates and short driving cycles.
- 10162068Some 2013-2017 C-Max/Fusion/MKZ Hybrid/Energi vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1450, P0456, P0457, P04EE and/or P04EF. This may be due to the sealing capability of the canister purge valve. To correct the condition, follow the Service Procedure steps to update the PCM software and replace the canister purge valve.
- 10144195Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
- 10074788Summary to be provided on a future date.
- 10058607Lincoln/ford: advance trac lamp or malfunction indicator lamp (mil) will be on with various diagnostic trouble codes (dtc) regarding evaporative emissions leak detection control module and possible replacement, if corrosion IS found. Model 2013-15 fusion, MKZ hybrid.
- 10058453Ford/lincoln: when flat towing vehicle, battery will drain, due to manual instruction of key remaining in accessory position. Model 2010-13 fusion, 2010-11 milan, 2011-12 MKZ.
- 10058094This tsb contains owners letter. See document search button. Ford my/ford lincoln 2011-2014 model year vehicles equipped with sync and myford/my lincoln touch. Warranty extension covering accessory protocol interface module software and hardware.
- 10057834Ford: no service action IS recommended for this condition. Please use at your discretion. Various 2010-2015 vehicles may experience a turbulence noise, similar to an helicopter noise, at highway speeds when the rear door window(s) or sunroof are open.
- 10057737Ford/lincoln: due to incorrect installation of fuel delivery module, some vehicles will indicate very low long fuel trim (longft1) readings and need to determine what part was installed. Model 2013 fusion, MKZ hybrid.
- 10056430Ford/lincoln: accompanied by the cmdtcs p1a18, p1a19, p0aee or p0bcd, the service engine soon lamp (energi) or wrench lamp (hybrid) will illuminate on some vehicles. Model 2013-2014 c-max, fusion, MKZ.
- 10056421Ford/lincoln: due to an adherence failure of rtv sealant, there IS a transmission fluid leakage, in some vehicles, from damper housing to transmission case joint. Model 2013 c-max, 2013-14 fusion, MKZ.
- 10056195Lincoln/ford: an investigation by engineers IS being done due to discharge from 12 volt battery and inspections of water pump connectors for corrosion or damage. Model 2013-2014 c-max, fusion hybrid, MKZ hybrid.
- 10056140Lincoln/ford: accompanied by cmdtc p1a18, p1a19, p0aee or p0bcd, the wrench lamp (hybrid) or service engine soon light may illuminate and the powertrain control module (pcm) needs to be reprogram to latest calibration. Model 2013-2014 fusion, MKZ.
- 10055312Ford: some model vehicles manual for powertrain control/emission diagnostic (pc/ed) has been updated regarding improved cooling fan circuit due to a lack of air conditioning, a malfunctioning indicator lamp (mil) and overheating.
- 10055028Ford: the transmission makes a metal on metal scraping sound and the noise IS present, in all gear ranges, when vehicle IS moving and not present when vehicle IS stationary or in park. Model 2013 c-max, 2013-2014 fusion.
- 10055015Lincoln/ford: on some vehicles, the illumination of the wrench lamp and/or red triangle lamp, the check engine lamp IS accompanied with various diagnostic trouble codes (dtcs) and service procedures updates. Model 2013 c-max, fusion, MKZ.
- 10054911Ford: the engine lamp or the wrench will be illuminated with diagnostic trouble codes (dtcs) p26ca and/or u019f. Model 2013-2014 fusion, MKZ.
Every Ford Fusion Hybrid model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.