2017 Ford Fusion Hybrid

Owner complaints

What owners report most

1. Power train18
2. Electrical system13
3. Unknown or other13
4. Steering13
5. Service brakes8
6. Air bags7
7. Engine7
8. Fuel/propulsion system4
9. Wheels3
10. Suspension3

Latest complaints

• Oct 2, 2026FL
  Steering
  Component: Power Steering Module Rack and Pinion assembly The wheel locked up as described below in the middle of me taking a left turn, with the errors popping up as described. The problem has been diagnosed by the local Ford dealership. Three warning lamps that are intermittently on when I start…

  Component: Power Steering Module Rack and Pinion assembly The wheel locked up as described below in the middle of me taking a left turn, with the errors popping up as described. The problem has been diagnosed by the local Ford dealership. Three warning lamps that are intermittently on when I start the vehicle, though are not always there: Steering Assist Fault Service Required Service AdvanceTrac Hill Start Assist Not Available. While these are up, the steering wheel will not turn without incredible effort, requiring a massive amount of force to turn the steering wheel, which results in very little change in the direction the car is moving.

• Sep 4, 2026CA
  Unknown or other
  Backup camera lens is defective and has UV damage / hazing. Makes reversing extremely difficult and dangerous as the lens is not giving a good image output to the infotainment screen to the point it is difficult to identify anything (cars, pedestrians, etc). Ford has a known recall on the fusions…

  Backup camera lens is defective and has UV damage / hazing. Makes reversing extremely difficult and dangerous as the lens is not giving a good image output to the infotainment screen to the point it is difficult to identify anything (cars, pedestrians, etc). Ford has a known recall on the fusions for 2013-2016, and have excluded 2017-2020 model years even though hardware is the same. I have ordered and am replacing the backup camera myself. Seems to be a common/known issue. Hoping to log a complaint and have Ford reimburse me for the trouble.

• Aug 28, 2026MO
  Steering
  The rack and pinion has failed twice within 2 and a half years. The steering has completely gone out twice while driving, causing extremely unsafe circumstances that could put multiple people in danger. After doing some research this is a common issue with Ford Fusions which is putting a lot of…

  The rack and pinion has failed twice within 2 and a half years. The steering has completely gone out twice while driving, causing extremely unsafe circumstances that could put multiple people in danger. After doing some research this is a common issue with Ford Fusions which is putting a lot of people in danger since it is a loss of steering issue. My wheel completely locked up while driving on the highway, how is this part not recalled yet? There are two separate safety recalls dealing with steering issues but the rack and pinion is not specifically mentioned so it is not covered under recall. This is extremely unsafe. Please look into this. Thank you.

• May 15, 2025AZFire
  Electrical system
  While driving roughly 5mph leaving from being parked for over 1.5 hours the hybrid battery caught/ control module caught on fire. Causing part of the truck carpet to catch fire. Since there was someone in the backseat that quickly felt the heat they turned the car off and stopped. The fire was put…

  While driving roughly 5mph leaving from being parked for over 1.5 hours the hybrid battery caught/ control module caught on fire. Causing part of the truck carpet to catch fire. Since there was someone in the backseat that quickly felt the heat they turned the car off and stopped. The fire was put out. We end having it towed to the ford dealership that could not identify the reason it caught on fire. This is a known issue but the recall only affected 2 days of production.

• Mar 17, 2025MN11,768 mi
  Electrical system
  The contact owns a 2017 Ford Fusion. The contact stated while using the key fob to start the vehicle, the heat on the front driver's seat and steering wheel failed to operate as intended. The contact manually depressed the button to turn on the heat. There was no warning light illuminated. The…

  The contact owns a 2017 Ford Fusion. The contact stated while using the key fob to start the vehicle, the heat on the front driver's seat and steering wheel failed to operate as intended. The contact manually depressed the button to turn on the heat. There was no warning light illuminated. The dealer was contacted and diagnosed that the instrument cluster and APIM needed to be replaced. The vehicle was repaired. The contact stated that the failure persisted. The vehicle was taken to a second dealer, White Bear Lincoln, Inc. (3425 Hwy 61 N, St Paul, MN 55110) who diagnosed that the instrument cluster and APIM needed to be replaced. The vehicle was repaired. The contact stated that the failure persisted. The manufacturer was notified of the failure but denied assistance in covering the cost of the repair. The contact was informed that the warranty had expired and was referred to the NHTSA Hotline to report the failure. The failure mileage was 11,768.

• Aug 29, 2024TX21,600 mi
  Air bags · Steering
  The contact owns a 2017 Ford Fusion Hybrid. The contact stated while making a left turn, the steering wheel made a complete 360-degree turn; however, the vehicle failed to respond as needed. Additionally, the horn and the buttons on the steering wheel became inoperable. The contact pushed up on the…

  The contact owns a 2017 Ford Fusion Hybrid. The contact stated while making a left turn, the steering wheel made a complete 360-degree turn; however, the vehicle failed to respond as needed. Additionally, the horn and the buttons on the steering wheel became inoperable. The contact pushed up on the steering wheel, applying a lot of pressure, to steer the vehicle while turning. Additionally, when the vehicle was started, the air bag warning light illuminated. The vehicle was not diagnosed or repaired. The contact believed that the failures were associated with NHTSA Campaign Number: 18V167000 (Steering). The manufacturer was notified of the failure. The failure mileage was approximately 21,600.

• Jul 3, 2024TN180,000 mi
  Engine · Power train
  The contact owns a 2017 Ford Fusion Hybrid. The contact stated that while driving 40 MPH, the vehicle shut off unexpectedly. The message that the engine was overheating was displayed. The check engine warning light was illuminated. The RED Triangle Symbol (Master Warning Light) was illuminated. The…

  The contact owns a 2017 Ford Fusion Hybrid. The contact stated that while driving 40 MPH, the vehicle shut off unexpectedly. The message that the engine was overheating was displayed. The check engine warning light was illuminated. The RED Triangle Symbol (Master Warning Light) was illuminated. The vehicle was towed to an independent mechanic, who determined that the transmission was leaking and that the hybrid system, battery, and engine needed to be replaced. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was contacted, and the contact was informed there were no open recalls on the VIN related to the failure. The contact was then referred to the NHTSA Hotline to report the failure. The approximate failure mileage was 180,000.

• Apr 1, 2024INCrash4 injuries
  Air bags · Unknown or other
  Airbags failed to deploy at 30-40 mph head on collision. Vehicle had an airbag light come up, was inspected by Ford and the RCM module was replaced as directed by manual. Airbags were also inspected at the time. Lights were cleared after the replacement. Was the car not reading the speed at the…

  Airbags failed to deploy at 30-40 mph head on collision. Vehicle had an airbag light come up, was inspected by Ford and the RCM module was replaced as directed by manual. Airbags were also inspected at the time. Lights were cleared after the replacement. Was the car not reading the speed at the time of the accident? My wife and 2 toddlers were in the vehicle at the time of the accident. I have a wrist injury and whiplash. Injuries could have been worse if it was a vehicle of twice the size or a semi.

• Mar 7, 2024MI104,000 mi
  Power train
  The contact owns a 2017 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, the contact heard a loud grinding sound coming from the vehicle. The vehicle was taken to the dealer where it was diagnosed with a failed transmission bearing and that the transmission needed to be…

  The contact owns a 2017 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, the contact heard a loud grinding sound coming from the vehicle. The vehicle was taken to the dealer where it was diagnosed with a failed transmission bearing and that the transmission needed to be replaced. The vehicle was not repaired. The contact was informed about TSB: 22-2396 however, the contact was informed that the vehicle could not be repaired under the TSB. The manufacturer was made aware of the failure and the contact was advised to report the failure to the NHTSA Hotline. The failure mileage was approximately 104,000.

• Mar 6, 2024PA100,000 mi
  Steering

  The contact owns a 2017 Ford Fusion Hybrid. The contact stated that the steering wheel had fractured. The contact stated that due to the failure, the steering wheel had an abnormal up and down movement. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 100,000.

• Dec 24, 2023CA
  Service brakes

  Brake service lights comes on. Noticed softer feel when pressing on brakes and longer distance needed to come to complete stop. There were no noticeable changes in driving habits before the maintenance light came on. Diagnostics were done 02/2023 at Sacramento Downtown Ford and was told to replace a brake hose.

• Nov 22, 2023AZ94,000 mi
  Power train
  The contact owns a 2017 Ford Fusion. The contact stated that the gear shifter failed to move out of park. The vehicle had been towed to the dealer. The dealer diagnosed that the transmission range control module had failed. The gear shifter was replaced; however, the failure persisted. The contact…

  The contact owns a 2017 Ford Fusion. The contact stated that the gear shifter failed to move out of park. The vehicle had been towed to the dealer. The dealer diagnosed that the transmission range control module had failed. The gear shifter was replaced; however, the failure persisted. The contact was informed that the transmission range control module needed to be replaced but was not yet replaced. The contact learned that the failure was related to NHTSA Campaign Number: 22V413000 (Power Train) however, the VIN was not included. The manufacturer was made aware of the failure and confirmed that the VIN was not included in the recall. The approximate failure mileage was 94,000.

• Nov 21, 2023FL111,760 mi
  Electrical system · Power train
  I purchased a used car from a dealership in Orlando, FL, on May 5th this year. The vehicle has been experiencing a recurring issue of a battery drain, and despite multiple visits to authorized Ford service centers and leaving the car with the dealership for repairs, the problem persists. My ability…

  I purchased a used car from a dealership in Orlando, FL, on May 5th this year. The vehicle has been experiencing a recurring issue of a battery drain, and despite multiple visits to authorized Ford service centers and leaving the car with the dealership for repairs, the problem persists. My ability as a customer to work and move around has been severely affected. The dealership claims no liability, but evidence suggests they were aware of the issue before selling the car. The service advisor admitted the problem existed before the purchase, providing repair orders from a different Ford location as proof. Currently, Ford is requesting 15 additional hours of labor for diagnosis, but the dealership refuses to approve it, leaving me with a non-functional vehicle. I suspect the vehicle's Power Control Module needs reprogramming due to a recall (Customer Satisfaction Program 17B38), but the VIN lookup shows no recalls associated with the car despite the model, year, plant city, build dates, as well as the reason for the recall matching. I, as the customer, am unable to use the purchased product, and Ford refuses to provide me with a response or any resolution as they “will not do anything until those 15 hours of labor = $3000 are not approved”, at the same time, financial constraints prevent me from approving the needed labor hours for diagnosis. Customer Satisfaction Program 17B38 Reason for this program: In some of the affected vehicles, if the ignition is briefly powered on and off, the PCM may not complete the shutdown process. As a result, the PCM will remain powered which results in excessive current draw and can lead to a drained battery. Affected vehicles Vehicle: Fusion Model Year: 2017 Plant City: Hermosillo Build Dates: 10/16/2015 - 08/02/2017

• Oct 11, 2023CA
  Engine
  CVT Transmission Vehicle purchased 4/15/19 with 38,000 miles Transmission was bad and was replaced under warranty by Ford on 8/13/2021 @ 77,099 miles. Noise is back and I took vehicle to dealer for diagnosis 10/10/2023. Diagnosis: Hybrid Electric Unit Motor went out/Transmission is bad and…

  CVT Transmission Vehicle purchased 4/15/19 with 38,000 miles Transmission was bad and was replaced under warranty by Ford on 8/13/2021 @ 77,099 miles. Noise is back and I took vehicle to dealer for diagnosis 10/10/2023. Diagnosis: Hybrid Electric Unit Motor went out/Transmission is bad and needs to be replaced @ 115,023 miles I have only driven the car $67,076 on this new transmission. This does not seem right. Dealership says I am out of "dealer warranty" and that I must pay out of pocket $7k

• Oct 11, 2023CA115,000 mi
  Power train
  The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, she heard an abnormal sound at the hood of the vehicle. No warning lights was illuminated. The vehicle was taken to the dealer where it was diagnosed that the transmission failed and needed to be…

  The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed, she heard an abnormal sound at the hood of the vehicle. No warning lights was illuminated. The vehicle was taken to the dealer where it was diagnosed that the transmission failed and needed to be replaced. The vehicle was repaired however, the contact stated that two years later the failure recurred. The manufacturer was notified of the failure and the contact was informed that there were no programs to assist with the repair. The failure mileage was approximately 115,000.

• Oct 4, 2023FL
  Power train

  Torque convertor weld studs fail the torque convertor will not be connected to the engine flexplate and the vechile will lose the ability to move, increasing the risk for a crash.

• Sep 28, 2023SC
  Suspension
  While shopping for Ford fusion hybrids, I notice they all displayed abnormal tire wear, specifically on the inside edge of the rear tires. After purchasing a 2017 fusion hybrid I have seen a significant tire wear issue on the rear inside edge of my tires causing premature tire replacement. I have…

  While shopping for Ford fusion hybrids, I notice they all displayed abnormal tire wear, specifically on the inside edge of the rear tires. After purchasing a 2017 fusion hybrid I have seen a significant tire wear issue on the rear inside edge of my tires causing premature tire replacement. I have had the wheel alignment checked and was told it was good. this seems to be an issue with this model. For someone that does not inspect or maintain tires this could lead to a tire blow out at speed. I have had put 3 sets of tires on the vehicle over the last 3 years.

• Sep 27, 2023FL
  Electrical system · Power train · Unknown or other

  1. Gear shift jammed (from 3 months of owning my car, until now -4 yrs). 2. Stop Safely Now Caution Light on. Vechile stops, then shuts off, can't turn it back on until about 20 minutes, Maybe Transmission? I am highly displeased! The transmission started to kick when this "Stop Safely Light" appeared. I could have been in a car accident.

• Aug 7, 2023SC
  Service brakes · Steering

  While traveling down the road, suddenly the steering gets hard to turn and the antilock brake system goes out. Usually, you can correct the problem by stomping on the brake or turning the car off and back on. Several warnings come up including Advancetrac failure. It’s a very dangerous situation when your power steering goes out while traveling down the road. This same issue has occurred more than 5 times.

• Jul 13, 2023TX
  Tires
  I bought 4 tires on 05/13/2023 from discount tire. Exactly 40 days (06/22/2023) from purchase, the sidewall of pssanger side rear tire blew out driving down a busy street with causing other vehicles to make advasive moves to avoid a collission. Discount tire replaced the tire with a different make…

  I bought 4 tires on 05/13/2023 from discount tire. Exactly 40 days (06/22/2023) from purchase, the sidewall of pssanger side rear tire blew out driving down a busy street with causing other vehicles to make advasive moves to avoid a collission. Discount tire replaced the tire with a different make of tire while stating that the bravuris 5 IS no longer made nor sold. Exactly 21 days later (07/13/2023) the second tire (driver rear) blew out the same way the first one did. Both tires blew in the exact same spot on the tire - close to the "safety warning" location on the tire. the first instance I was traveling at 35mph and luckily avoided a collision, the 2ND time I was traveling at 10mph turning a corner-again luckily I was able to avoid a collision. From the time the tires were purchased until the 2ND tire blew out, the vehicle had only been driven about 500-550 miles total.

• Jul 13, 2023VA
  Wheels

  The lug nuts on the wheels swell nd tcannot be removed. This, in turn, causes an extreme danger when trying to change a flat tire on the side of the road.

• Jul 5, 2023IL
  Electrical system · Service brakes
  What component or system failed or malfunctioned, and is it available for inspection upon request? The component that failed is the vacuum pump in a ford hybrid car model 2017. Yes is available for inspection. How was your safety or the safety of others put at risk?Is a big risk for me and others…

  What component or system failed or malfunctioned, and is it available for inspection upon request? The component that failed is the vacuum pump in a ford hybrid car model 2017. Yes is available for inspection. How was your safety or the safety of others put at risk?Is a big risk for me and others because is related to the brake system Has the problem been reproduced or confirmed by a dealer or independent service center? Yes the problem was diagnosed and confirmed by Ford car agency in SLP Mexico Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? No only by the Ford agency in SLP Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? Yes a red message was showed indicating review brake system, and the brake hand be activated when I was driving, I got this message at April 18th 2023, I pay to the ford car agency to review and they indicated that it was a sensor that dos not work so they reprogrammed it, then on June 27th the warning message appear again, then I reach the ford car agency and now they are telling me that the vacuum pump is failing and needs to be replaced

• Jun 15, 2023IA
  Unknown or other

  Trunk unlatches itself when car is unlocked, has happened when backing out of driveway, it doesn’t do it for a few weeks then starts back up again,

• May 31, 2023KY
  Service brakes
  Some months ago the check brakes light came on. I went to the brake shop and they said there was a little wear on the rear brake pads so they replaced them and cleaned all the brakes and filled the fluid. I was fine for a a while then a few months ago the check brakes light reappeared. at that…

  Some months ago the check brakes light came on. I went to the brake shop and they said there was a little wear on the rear brake pads so they replaced them and cleaned all the brakes and filled the fluid. I was fine for a a while then a few months ago the check brakes light reappeared. at that time I saw ford was recalling my car model for faulty brake lines. I called ford and the local dealer and they said my car IS not recalled yet. I also emailed ford with the same reply. now I notice IS I park my car where the front IS elevated the brakes are very loose and I have to pump them to stop when I put the car in reverse.

• May 17, 2023MDCrash
  Air bags · Electrical system · Seat belts
  On or about January 2023, I noticed the airbag light come on my vehicle's dashboard. I didn't notice anything else that may have suggested what was wrong or what caused the light to come on. On February 6, 2023, I took the car to a Ford dealership to be inspected (the car had less than 60,000…

  On or about January 2023, I noticed the airbag light come on my vehicle's dashboard. I didn't notice anything else that may have suggested what was wrong or what caused the light to come on. On February 6, 2023, I took the car to a Ford dealership to be inspected (the car had less than 60,000 miles and was about 6 years old at the time). After an inspection, I was told that the "Restraint Control Module" (RCM) had failed and that the part I needed was on national backorder. I asked the sales person if this meant that my airbags wouldn't deploy in an accident. His answer was unclear, and he said that "the airbags would at least not deploy unintentionally". On May 6, 2023, I was involved in an accident and the airbags did NOT deploy. I am unsure if there was enough force during the accident that would have caused the airbags to deploy, or whether they should have deployed but did not due to the bad RCM component. Today, May 17, 2023, my car is currently being repaired at an auto body shop. I called Ford's customer service because I am concerned about driving with potentially non-working airbags. I was told that the part I need (HS7Z14B321H) is still on national backorder and may take at least two more months to be back in stock. Ford recommended filing a report with NHTSA. I feel that the car is not safe to drive and I am concerned for the safety of myself and passengers. Please let me know if you have any additional questions or recommend any solutions to resolve this situation. Thank you for your time.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Pedestrian alert sounds

  DP22005Opened Jan 27, 2023Closed Aug 7, 2023Recall 22V063000
  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…

  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

• Front Brake Jounce Hose Failures

  RQ22004Opened Aug 8, 2022Closed Mar 24, 2023Recall 23V162000
  On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the…

  On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturing on certain MY 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The result causes a brake fluid leak, lengthening the distance needing to stop the vehicle, increasing the risk of a crash.On March 10, 2023, Ford Motor Company (Ford) submitted to NHTSA Safety Recall 23V-162 (Ford Recall 23S12) to address front brake jounce hoses that may rupture. Ford found the rupture occurs from a localized failure of the internal reinforcement braid due to cyclic fatigue through tensile/bending and torsional inputs during suspension and steering articulations. The supplier for the front brake jounce hoses is Hitachi. This recall affects the subject vehicles equipped with non-hybrid engines and the suspect front brake jounce hoses (a total of 1,280,726 vehicles). The recall covers subject vehicles built from February 3, 2012 to July 19, 2017 when the suspect hoses were used in vehicle production. The remedy is for dealerships to replace both front brake jounce hoses with new hoses that have a revised braid material at no cost. The vehicles equipped with hybrid engines are excluded from the recall because the internal hose pressure is much lower due to the regenerative braking provided by the hybrid brake system. No failures of brake hoses on hybrid vehicles have been reported to ODI or Ford.Ford's actions address ODIs concerns at this time. Hybrid vehicles will be monitored for related failures. The agency reserves the right to take further action if warranted by new circumstances.The 103 ODI numbers cited above can be viewed at NHTSA.gov under the following ID numbers:11511014, 11510867, 11510318, 11509030, 11505993, 11504989, 11504400, 11502147, 11502082, 11501820, 11501283, 11498439, 11498296, 11496842, 11496335, 11494931, 11494851, 11494252, 11493001, 11492084, 11492070, 11491444, 11491274, 11488858, 11488027, 11487627, 11487416, 11487233, 11486150, 11484924, 11484526, 11484080, 11483948, 11483926, 11483739, 11483723, 11482773, 11482690, 11481077, 11480788, 11480294, 11480052, 11479338, 11479334, 11479252, 11479247, 11479187, 11479094, 11479048, 11478985, 11478953, 11478729, 11478216, 11476892, 11476282, 11470558, 11468994, 11467109, 11466294, 11462746, 11461217, 11456065, 11455367, 11444848, 11436419, 11436376, 11430685, 11428329, 11425083, 11421026, 11420738, 11420735, 11420298, 11418197, 11403926, 11397549, 11366991, 11366757, 11361016, 11359968, 11354569, 11352165, 11350344, 11348799, 11343929, 11343205, 11331947, 11329020, 11319596, 11310529, 11292271, 11288455, 11254787, 11253479, 11253244, 11234622, 11230669, 11230050, 11228240, 11221111, 11143630, 11129392 and 11120228.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10251952For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
• 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
• 10244801This article supersedes TSB 22-2181 to update the Service Procedure and Part List. Some 2015-2017 Edge, 2016-2017 MKX, 2017 Fusion/MKZ/Continental vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion. To correct the condition, follow the Service Procedure to replace the valve covers and replace the factory oil pan with a press in place gasket style oil pan.
• 10241627In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
• 10240743The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
• 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
• 10233681Some 2014-2020 Fusion and 2017-2019 Escape vehicles may be equipped with a 1.5L Ecoboost engine that uses a 50-tooth variable camshaft timing (VCT) intake and exhaust unit from the assembly plant or if a service long block was installed. VCT locking tool 303-1097 is not compatible with this system. If VCT system service is required, replace both the intake VCT (service part DS7Z-6256-F) and exhaust VCT (service part DS7Z-6256-G) as a pair. An interim loaner tool program has been established to enable these repairs. Contact 1-800-403-4844 (Monday-Friday 8:00am to 8:00pm EST; Saturday 8:00am to 3:00pm EST) to obtain this tool. A VCT locking tool compatible with the 50-tooth system is under development and will be sent to dealerships. Continue to monitor OASIS for additional information.
• 10228876Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10225458Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
• 10225447Some 2015-2018 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure to replace the flexplate, transmission fluid pump, and torque converter.
• 10224795Some 2015-2017 Edge, 2016-2017 MKX, 2017 Fusion/MKZ/Continental vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine vehicles may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
• 10222788Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10218621Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10218617Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10217028Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
• 10214832Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
• 10214758Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10214126Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure to replace the long block engine assembly.
• 10212957Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
• 10211728Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
• 10211709Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10210941In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
• 10210816Some 2017-2021 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10210392Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10210391Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
• 10209209This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
• 10208146Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
• 10207136Some 2017-2020 Fusion/MKZ and 2017-2019 Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
• 10205694Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
• 10203848Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
• 10203841Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10203840Some 2017 MKZ and Fusion vehicles equipped with memory seats and built on or before 03-Jun-2016 may exhibit a discharged battery or a battery drain condition. Before performing normal diagnostics, reprogram the driver door module (DDM) to the latest calibration using the Integrated Diagnostic System (IDS). Use causal part 14B291 and applicable labor operations from Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10202708Some 2015-2020 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure steps to replace the flexplate, transmission fluid pump, and torque converter.
• 10201614Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10201582Some 2016-2017 Ford and Lincoln vehicles with a new body control module (BCM) installed may exhibit a programming error when using IDS versions 122.03 through 123.01 stating 'Data Corrupt' or 'Configuration Failed, would you like to retry?'. IDS scan tool version 123.02 contains a fix for this programming error. Install IDS version 123.02 or later from PTS > Rotunda tab > Diagnostic Tool Support > Download Software. Once installed, perform the BCM programmable module installation (PMI). Refer to Workshop Manual (WSM), Section 419-10 > Removal and Installation.
• 10201050Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10201034Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10201024Some 2016-2017 Ford and Lincoln vehicles with a new Body Control Module (BCM) installed may exhibit a programming error using IDS v122.03 and newer stating "Data Corrupt" or Configuration Failed, would you like to retry?. A temporary work around has been released to complete the BCM programming process. Uninstall IDS from the computer. Run the IDS clean up utility tool located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Install IDS v122.01 (122_FULL) by copying the following link into an internet address bar https://www.fordservicecontent.com/Ford_Content/IDS/SoftwareUpdates/IDS-122.01_full.exe. Retry the BCM Programmable Module Installation (PMI) using IDS level 122.01. Monitor OASIS for updates.
• 10201019Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
• 10201013Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Every Ford Fusion Hybrid model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.