2018 Ford Fusion Hybrid

Owner complaints

What owners report most

1. Electrical system10
2. Power train10
3. Unknown or other8
4. Service brakes7
5. Steering7
6. Wheels7
7. Air bags6
8. Engine4
9. Engine and engine cooling3
10. Seat belts3

Latest complaints

• Aug 5, 2026CA
  Air bags · Forward collision avoidance › Warnings · Unknown or other
  The leather-covered dashboard panel, in the approximately 4-6 inch section between the base of the windshield and the first seam across the dash, has shrunk, rippled, and pulled away from the underlying substrate. This area also houses the driver-assist camera housing and the defrost vent. The…

  The leather-covered dashboard panel, in the approximately 4-6 inch section between the base of the windshield and the first seam across the dash, has shrunk, rippled, and pulled away from the underlying substrate. This area also houses the driver-assist camera housing and the defrost vent. The vehicle was purchased new and has been Ford-maintained, professionally detailed, and garage-kept throughout ownership; the leather has been regularly cleaned and conditioned as part of routine dealership detailing, ruling out lack of care as a cause. The vehicle's build date is January 2018, which falls within the range covered by Ford Technical Service Bulletin 18-2283 ("Instrument Panel Sagging at the Windshield Glass"), issued for vehicles built between October 13, 2014 and February 2, 2018, describing the instrument panel sagging and separating near the windshield. I am filing this complaint because this appears to be a documented, recurring defect pattern affecting this vehicle's dash generation, rather than isolated cosmetic wear. Ford Customer Relations has twice declined goodwill assistance, citing the vehicle's age (just over 8 years) as the sole basis, without physical inspection or evaluation of the underlying condition. An independent repair estimate to replace the dash panel and remove/reinstall the windshield for access was quoted at approximately $3,100.

• Jun 30, 2026VA1 injury
  Service brakes

  The chrome trim on the parking brake switch started chipping. The sharp edge drew a drop of blood and small pieces attached to your fingers. Replaced the switch in June 2026

• Jun 16, 2026UTCrash2 injuries
  Air bags

  The air bags did not deploy on the front passenger side after a two car accident. There was an injury to the passenger of the car. Vehicle was inspected by police and there were no warning signs

• Aug 23, 2025TXCrash
  Electrical system · Service brakes · Steering
  I am reporting a serious safety issue with my 2018 Ford Fusion Hybrid SE that affects the braking system and related electronics: 1.The ABS stopped functioning previously. 2.Recently, the car displayed a “Brake Malfunction” warning for the first time, which appears when making sharp turns. 3.The…

  I am reporting a serious safety issue with my 2018 Ford Fusion Hybrid SE that affects the braking system and related electronics: 1.The ABS stopped functioning previously. 2.Recently, the car displayed a “Brake Malfunction” warning for the first time, which appears when making sharp turns. 3.The TPMS (tire pressure monitoring system) stopped working some time ago. These issues are extremely dangerous. The electronic brake booster and ABS module are critical for safe braking, especially in emergency situations. With the ABS and brake assist compromised, the pedal can suddenly become rock hard or soft, stopping distance increases dramatically, and traction control/ABS is unavailable during hard braking. I am concerned this is a systemic issue with the 2018 Ford Fusion Hybrid SE braking system and not isolated to my vehicle. This failure could put drivers, passengers, and others on the road at serious risk. I request that NHTSA investigate this issue for potential recall action to protect the safety of drivers nationwide.

• Feb 7, 2025OH
  Service brakes

  Leaking fluid, etc similar to recall on other 2018 Ford Fusions

• Feb 7, 2025OH
  Power train

  Bad bearings in hybrid transmission

• Dec 4, 2024MO
  Power train
  1. What component or system failed or malfunctioned, and is it available for inspection upon request? - The transmission has failed twice. The first time it was replaced by a licensed dealer. The second time is current. It is available for inspection upon request. 2. How was your safety or the…

  1. What component or system failed or malfunctioned, and is it available for inspection upon request? - The transmission has failed twice. The first time it was replaced by a licensed dealer. The second time is current. It is available for inspection upon request. 2. How was your safety or the safety of others put at risk? -We were stranded on the highway in Missouri. The second time the car failed was during winter weather with two small children, putting us at significant risk due to exposure to extreme cold and the dangers of being stuck on the side of the highway. 3. Has the problem been reproduced or confirmed by a dealer or independent service center? - Yes, the problem was confirmed by a dealer/service center after the first failure, and it has occurred again. 4. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives, or others? - Yes, it has been inspected by a dealer, but not by the manufacturer, police, or insurance representatives. 5. Were there any warning lamps, messages, or other symptoms of the problem prior to the failure, and when did they first appear? - Yes, the first time it failed we got an engine overheating error. The second time it failed we got the "wrench" error code. These warning signs occurred as the problem occurred and did not give us any time to get the car to safety.

• Nov 29, 2024AZ94,000 mi
  Engine and engine cooling
  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, the vehicle shuddered momentarily. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, where it was determined that the engine had failed due to…

  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while driving at an undisclosed speed, the vehicle shuddered momentarily. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, where it was determined that the engine had failed due to coolant intrusion. The contact was informed that the engine needed be replaced. The vehicle was not repaired. The contact related the failure to Ford Campaign Number: 21N12. The manufacturer was notified of the failure. A case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 94,000.

• Oct 4, 2024CA70,000 mi
  Power train
  The contact's mother owns a 2018 Ford Fusion Hybrid. The contact stated while his mother was pulling into a parking space, the vehicle abruptly stopped independently. The driver noticed that the vehicle had shifted to park(P) independently, and the gear shifter was stuck in park(P). An unknown…

  The contact's mother owns a 2018 Ford Fusion Hybrid. The contact stated while his mother was pulling into a parking space, the vehicle abruptly stopped independently. The driver noticed that the vehicle had shifted to park(P) independently, and the gear shifter was stuck in park(P). An unknown warning light was illuminated. The driver turned off and restarted the vehicle; however, the gear shifter remained stuck in park(P). An independent mechanic arrived on the scene but was unable to correct the failure. The vehicle was towed to an independent mechanic to be diagnosed. The vehicle was not yet diagnosed or repaired. The dealer was notified of the failure and advised the contact to schedule an appointment for diagnostic testing. The manufacturer was not notified of the failure. The failure mileage was approximately 70,000.

• Sep 29, 2024KY
  Power train
  In Mid-August I was sitting at a stop light about to turn left. I was about the 3rd car in line. The light turned, and the first car turned left, and we inched up the car in front of me was able to turn, and the traffic was clear enough for me to also make the turn. However, in the middle of the…

  In Mid-August I was sitting at a stop light about to turn left. I was about the 3rd car in line. The light turned, and the first car turned left, and we inched up the car in front of me was able to turn, and the traffic was clear enough for me to also make the turn. However, in the middle of the turn my car didn’t stall out but lost all acceleration. I was pushing the gas, but while the car coasted forward it didn’t begin the drive. However, I never lost power. It was like the car jumped from “Drive” into “Neutral” and I coasted through the turn. I hesitated slightly and then pushed on the gas. The engine made sound but no movement other than coasting. Finally, I felt a small jolt and the car started moving forward. I was able to clear the intersection and was back in Drive mode. At that time the “Engine Warning” light came up on the dash. The car was able to move, nothing else seemed to have a problem, breaks still worked, I pulled into a parking lot. I pulled over, parked, but did not turn the car off immediately. I was able to drive forward and back-up while in the parking lot, as well as make turns. After about a minute I turned the car off to see if the car would automatically “fix itself”. I waited about three minutes and then started the car again, and it started without any problem, but the Warning light was still on. I left the parking lot and was able to drive with the Engine Warning light was still on, but no problem with anything else. I drove about five miles toward home when the Warning light turned OFF. I drove to Oxmoor Ford for service, but the service department was closed. I then drove to AutoZone where they did an initial plug into see if they could find what caused the problem. They were not able to determine anything. I returned home and made the appointment for the Oxmoor Ford service center. The car service cost me $7371.17.

• Sep 18, 2024KY48,000 mi
  Power train
  The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, the transmission unexpectedly downshifted with the transmission warning light illuminated. The vehicle was able to restart; however, the failure recurred. The vehicle was taken to the dealer where it was…

  The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, the transmission unexpectedly downshifted with the transmission warning light illuminated. The vehicle was able to restart; however, the failure recurred. The vehicle was taken to the dealer where it was diagnosed with transmission failure. The contact was informed that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure, a case was opened, and the contact was referred to the NHSTA Hotline for assistance. The failure mileage was approximately 48,000.

• Jul 2, 2024FL133,898 mi
  Steering
  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while driving 2 MPH and making a U-turn, the steering wheel was loose and wiggling. The contact stated that the steering wheel turned 360 degrees. The steering wheel was uncontrollable. The “Uphill Park Assist” warning light was…

  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while driving 2 MPH and making a U-turn, the steering wheel was loose and wiggling. The contact stated that the steering wheel turned 360 degrees. The steering wheel was uncontrollable. The “Uphill Park Assist” warning light was illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 133,898.

• May 21, 2024NC190,000 mi
  Engine and engine cooling
  The contact owns a 2018 Ford Fusion Hybrid. The contact stated that coolant needed to be added to the coolant reservoir occasionally. While driving at various speeds, the engine overheated. Additionally, there was an abnormal rattling sound coming from the vehicle and the vehicle was slow to start.…

  The contact owns a 2018 Ford Fusion Hybrid. The contact stated that coolant needed to be added to the coolant reservoir occasionally. While driving at various speeds, the engine overheated. Additionally, there was an abnormal rattling sound coming from the vehicle and the vehicle was slow to start. The traction, engine, and air bag warning lights were illuminated. The vehicle was taken to an independent mechanic, who informed the contact that the head gasket had blown. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 190,000.

• May 2, 2024CA
  Back over prevention › Warnings · Electrical system · Service brakes

  Park Break engages on its on when the engine is turned off

• Mar 29, 2024MD160,300 mi
  Service brakes, hydraulic
  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while driving 45 MPH and depressing the brake pedal, the brake pedal went to the floorboard, and the vehicle failed to respond as needed. The brake warning light was illuminated. The contact engaged the electric parking brake and the…

  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while driving 45 MPH and depressing the brake pedal, the brake pedal went to the floorboard, and the vehicle failed to respond as needed. The brake warning light was illuminated. The contact engaged the electric parking brake and the vehicle stopped. The contact stated that upon inspecting the vehicle and determined that the brake line on the output of the ABS pump had failed. The contact stated that the front driver's side brake hose had previously ruptured and was replaced. The vehicle was taken to the dealer but was not diagnosed or repaired. The dealer informed the contact that the VIN was not included in a recall. The manufacturer was notified of the failure and informed the contact that the VIN was not included in NHTSA Campaign Number: 23V162000 (Service Brakes, Hydraulic). The failure mileage was approximately 160,300.

• Mar 20, 2024SC
  Wheels · Wheels › Lugs/nuts/bolts/studs
  In for a normal oil change and tire rotation. The lug nuts were swollen and had to be broke off and replaced. with the same one that were on my car. I did not no Ford had a lug nut problem until then. To find out that some people had to have cars towed because of the tire not being able to come…

  In for a normal oil change and tire rotation. The lug nuts were swollen and had to be broke off and replaced. with the same one that were on my car. I did not no Ford had a lug nut problem until then. To find out that some people had to have cars towed because of the tire not being able to come off. It is a saftey hazard. Ford know this and keeps making these lug nuts. Saying to replace every 50,000 miles at 160 dollars. this is crazy. I am sure there are many people who do not even know till it is too late. They should come up with a different design and replace them all. I travel 80 miles a day, and i rotate every 5,000 miles. i will be replacing them way too may times at this rate. this is unecessary.

• Mar 12, 2024NC118,000 mi
  Engine and engine cooling
  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while her husband was driving 35-40 MPH after an oil change had been performed on the vehicle, the check engine warning light illuminated. The vehicle was taken back to the mechanic, where it was diagnosed that there was a coolant…

  The contact owns a 2018 Ford Fusion Hybrid. The contact stated while her husband was driving 35-40 MPH after an oil change had been performed on the vehicle, the check engine warning light illuminated. The vehicle was taken back to the mechanic, where it was diagnosed that there was a coolant intrusion in the engine. The mechanic determined that the engine needed to be replaced. The vehicle was not repaired. An unknown dealer was notified of the failure. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 118,000.

• Mar 5, 2024MO65,000 mi
  Steering
  The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the steering was inoperable. The steering wheel detached from the steering column and the steering wheel was spinning at a 360-degree motion. The contact stated that there was no motion on the…

  The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the steering was inoperable. The steering wheel detached from the steering column and the steering wheel was spinning at a 360-degree motion. The contact stated that there was no motion on the tires. The vehicle was towed to an independent mechanic where it was diagnosed with a fractured steering bolt. The contact was advised that the extent of the failure had not been determined and could be provided only if the contact agreed to have repairs completed. The contact was informed of NHTSA Campaign Number: 18V167000(Steering). The vehicle was not repaired. The manufacturer was made aware of the failure and a case was filed. The contact was advised to report the failure to NHTSA. The failure mileage was approximately 65,000.

• Feb 28, 2024AZ
  Wheels · Wheels › Lugs/nuts/bolts/studs

  I recently had to replace all of the lug nuts on this car due to swelling. Ford said they were all faulty. There were no warnings about the problem. It was noticed in a routine service appointment. I was informed the risk could be that I would not be able to remove them if I experienced a flat tire, and therefore be left stranded.

• Feb 13, 2024ME
  Electrical system · Power train
  Driving down the road and suddenly all the lights came on and lost power steering there was no warning. Nothing. It stopped working. I then see something today in regards to this being an issue and when I contact ford about it was nothing we can do. Ford did not make this very public and I bet if…

  Driving down the road and suddenly all the lights came on and lost power steering there was no warning. Nothing. It stopped working. I then see something today in regards to this being an issue and when I contact ford about it was nothing we can do. Ford did not make this very public and I bet if you people expanded this to other newer models and made it public you might find more people that have had the same issue and thought it was just their car.

• Feb 9, 2024CA82,000 mi
  Electrical system › 12v/24v/48v battery
  The contact owns a 2018 Ford Fusion Hybrid. The contact stated that upon attempting to start the vehicle, the vehicle failed to start. The vehicle was jumpstarted. After jumpstarting the vehicle, the vehicle performed normally. However, the contact stated that the battery failure became a regular…

  The contact owns a 2018 Ford Fusion Hybrid. The contact stated that upon attempting to start the vehicle, the vehicle failed to start. The vehicle was jumpstarted. After jumpstarting the vehicle, the vehicle performed normally. However, the contact stated that the battery failure became a regular failure. The low battery warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 82,000.

• Dec 7, 2023SC180,000 mi
  Service brakes
  The contact owns a 2018 Ford Fusion Hybrid. The contact stated that after starting the vehicle and depressing the brake pedal, there was a grinding sound coming from the front brake pads. After shifting into drive, the message "Emergency Brake Failure, Vehicle Shutting Off" was displayed and the…

  The contact owns a 2018 Ford Fusion Hybrid. The contact stated that after starting the vehicle and depressing the brake pedal, there was a grinding sound coming from the front brake pads. After shifting into drive, the message "Emergency Brake Failure, Vehicle Shutting Off" was displayed and the vehicle turned off. After restarting the vehicle, the vehicle operated normally. The cause of the failure was not yet determined. The local dealer was notified of the failure. The manufacturer was not yet contacted. The failure mileage was 180,000.

• Sep 18, 2023FL
  Visibility/wiper
  I have a problem with the variable speed windshield wipers. This has occurred twice now in the past 2 weeks or so and I paid a little closer attention to the symptoms the second time (yesterday). When the problem occurs, the wipers have only ONE speed: LOW. The speed does not increase as the rain…

  I have a problem with the variable speed windshield wipers. This has occurred twice now in the past 2 weeks or so and I paid a little closer attention to the symptoms the second time (yesterday). When the problem occurs, the wipers have only ONE speed: LOW. The speed does not increase as the rain gets heavier AND you can not increase the speed by switching the selector to HIGH either. So.....as the rain gets heavier, the visibility gets REALLY bad and the only solution seems to be to slow WAY down, which is not a good thing to suddenly do on a "freeway". I was able to determine if I select OFF on the wiper control and then turn it back ON, the problem (sometimes) goes away and the wipers operate normally.......for a while. Of course, turning the wipers OFF during heavy rain isn't a good thing to do either. I am calling my Ford dealer today to make an appointment for service. Since the condition has been intermittent (so far), I fear that their answer might be "no trouble found" if they can't observe the failure themselves.

• Sep 11, 2023CA90,000 miCrash1 injury
  Air bags
  The contact owned a 2018 Ford Fusion. The contact stated that while driving at 40 MPH, she was rear-ended by another vehicle. The air bags did not deploy. A police report was filed, and injuries were reported. The contact was later treated for various bruising in an area hospital, as well as…

  The contact owned a 2018 Ford Fusion. The contact stated that while driving at 40 MPH, she was rear-ended by another vehicle. The air bags did not deploy. A police report was filed, and injuries were reported. The contact was later treated for various bruising in an area hospital, as well as receiving a CT scan and an x-ray of her left ankle. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic; instead, it was towed to a tow yard and deemed a total loss. The manufacturer was not notified of the failure. The failure mileage was 90,000.

• Aug 18, 2023CA68,000 mi
  Steering · Suspension › Front › Control arm › Lower ball joint
  The contact owns a 2018 Ford Fusion. The contact stated while driving 30 MPH, there was a clicking sound coming from the vehicle. There was no warning light illuminated. The vehicle was taken to the dealer and the fuel pump was replaced. On another occasion, while driving 40 MPH, the vehicle turned…

  The contact owns a 2018 Ford Fusion. The contact stated while driving 30 MPH, there was a clicking sound coming from the vehicle. There was no warning light illuminated. The vehicle was taken to the dealer and the fuel pump was replaced. On another occasion, while driving 40 MPH, the vehicle turned to the right independently. There was no warning light illuminated. The contact was able to steer the vehicle and drove into the curb where the vehicle came to a complete stop. The vehicle was towed to the dealer and the contact was informed that the front driver’s side ball joints had separated from the vehicle. The vehicle was deemed a total loss by the insurance company. The manufacturer was contacted, and a case was filed. The failure mileage was approximately 68,000.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Pedestrian alert sounds

  DP22005Opened Jan 27, 2023Closed Aug 7, 2023Recall 22V063000
  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…

  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

• Front Brake Jounce Hose Failures

  RQ22004Opened Aug 8, 2022Closed Mar 24, 2023Recall 23V162000
  On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the…

  On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturing on certain MY 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The result causes a brake fluid leak, lengthening the distance needing to stop the vehicle, increasing the risk of a crash.On March 10, 2023, Ford Motor Company (Ford) submitted to NHTSA Safety Recall 23V-162 (Ford Recall 23S12) to address front brake jounce hoses that may rupture. Ford found the rupture occurs from a localized failure of the internal reinforcement braid due to cyclic fatigue through tensile/bending and torsional inputs during suspension and steering articulations. The supplier for the front brake jounce hoses is Hitachi. This recall affects the subject vehicles equipped with non-hybrid engines and the suspect front brake jounce hoses (a total of 1,280,726 vehicles). The recall covers subject vehicles built from February 3, 2012 to July 19, 2017 when the suspect hoses were used in vehicle production. The remedy is for dealerships to replace both front brake jounce hoses with new hoses that have a revised braid material at no cost. The vehicles equipped with hybrid engines are excluded from the recall because the internal hose pressure is much lower due to the regenerative braking provided by the hybrid brake system. No failures of brake hoses on hybrid vehicles have been reported to ODI or Ford.Ford's actions address ODIs concerns at this time. Hybrid vehicles will be monitored for related failures. The agency reserves the right to take further action if warranted by new circumstances.The 103 ODI numbers cited above can be viewed at NHTSA.gov under the following ID numbers:11511014, 11510867, 11510318, 11509030, 11505993, 11504989, 11504400, 11502147, 11502082, 11501820, 11501283, 11498439, 11498296, 11496842, 11496335, 11494931, 11494851, 11494252, 11493001, 11492084, 11492070, 11491444, 11491274, 11488858, 11488027, 11487627, 11487416, 11487233, 11486150, 11484924, 11484526, 11484080, 11483948, 11483926, 11483739, 11483723, 11482773, 11482690, 11481077, 11480788, 11480294, 11480052, 11479338, 11479334, 11479252, 11479247, 11479187, 11479094, 11479048, 11478985, 11478953, 11478729, 11478216, 11476892, 11476282, 11470558, 11468994, 11467109, 11466294, 11462746, 11461217, 11456065, 11455367, 11444848, 11436419, 11436376, 11430685, 11428329, 11425083, 11421026, 11420738, 11420735, 11420298, 11418197, 11403926, 11397549, 11366991, 11366757, 11361016, 11359968, 11354569, 11352165, 11350344, 11348799, 11343929, 11343205, 11331947, 11329020, 11319596, 11310529, 11292271, 11288455, 11254787, 11253479, 11253244, 11234622, 11230669, 11230050, 11228240, 11221111, 11143630, 11129392 and 11120228.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10251952For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
• 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
• 10241627In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
• 10240743The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
• 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
• 10233681Some 2014-2020 Fusion and 2017-2019 Escape vehicles may be equipped with a 1.5L Ecoboost engine that uses a 50-tooth variable camshaft timing (VCT) intake and exhaust unit from the assembly plant or if a service long block was installed. VCT locking tool 303-1097 is not compatible with this system. If VCT system service is required, replace both the intake VCT (service part DS7Z-6256-F) and exhaust VCT (service part DS7Z-6256-G) as a pair. An interim loaner tool program has been established to enable these repairs. Contact 1-800-403-4844 (Monday-Friday 8:00am to 8:00pm EST; Saturday 8:00am to 3:00pm EST) to obtain this tool. A VCT locking tool compatible with the 50-tooth system is under development and will be sent to dealerships. Continue to monitor OASIS for additional information.
• 10233587Some 2018-2019 Edge/Continental, 2018 MKX and 2019 Nautilus vehicles built on or before 1-Aug-2019 and 2018-2019 Fusion/MKZ vehicles built on or before 15-Aug-2019 equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. To correct the condition, follow the Service Procedure steps to replace the oil pan with a new oil pan equipped with a press in place gasket.
• 10228876Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10225458Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
• 10225447Some 2015-2018 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure to replace the flexplate, transmission fluid pump, and torque converter.
• 10222788Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10218621Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10218617Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10217028Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
• 10214832Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
• 10214758Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10214126Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure to replace the long block engine assembly.
• 10212957Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
• 10211728Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
• 10211709Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10210941In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
• 10210816Some 2017-2021 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10210392Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10210391Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
• 10209209This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
• 10208146Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
• 10207136Some 2017-2020 Fusion/MKZ and 2017-2019 Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
• 10205694Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
• 10205482Some 2018-2021 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10203848Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
• 10203841Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10202708Some 2015-2020 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure steps to replace the flexplate, transmission fluid pump, and torque converter.
• 10201614Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10201050Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10201034Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10201019Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
• 10201013Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
• 10199536Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
• 10198605Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
• 10194428Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Every Ford Fusion Hybrid model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.