2014 Ford Fusion Hybrid

Recalls

1 recall names the 2014 Ford Fusion Hybrid. Newest first.

• Equipment › Electrical

  Sep 10, 2018NHTSA 18V59200049,197 vehicles

  Ford Motor Company (Ford) is recalling certain 120V Convenience charge cords that were supplied with and sold for use with 2013-2015 Ford C-Max Energi and Fusion Energi vehicles and 2012-2015 Ford Focus Electric vehicles. Cords with part numbers FM58-10B706-AA, FM58-10B706-AB, FM58-10B706-AC, FM58-10B706-AD, FM58-10B706-AE and FM58-10B706-AF were…

  Risk and remedy

  Risk

  An overheated cord can increase the risk of a fire.

  Remedy

  Ford will notify owners, and dealers will replace the current cord with a new 120V convenience cord with a thermistor, free of charge. The recall began January 18, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S24.

  Full recall details →

Owner complaints

What owners report most

1. Steering14
2. Power train12
3. Service brakes11
4. Electrical system10
5. Engine7
6. Unknown or other5
7. Structure4
8. Seat belts4
9. Air bags3
10. Fuel/propulsion system3

Latest complaints

• Oct 31, 2025CA
  Service brakes
  Brake lights stay on even after turning off car. According to my research the problem is a brake pedal bumper that deteriorated. I actually found the rubber piece on the floor. Prior to finding out my brakes remained on, the red engine light turned on. I checked recalls for this problem, and there…

  Brake lights stay on even after turning off car. According to my research the problem is a brake pedal bumper that deteriorated. I actually found the rubber piece on the floor. Prior to finding out my brakes remained on, the red engine light turned on. I checked recalls for this problem, and there was one, but it was only valid for high humidity States. I live in California so I didn't qualify. Now, due to not knowing what the red light was about, and it being smog time, I cleared the engine light. Well, I didn't know that disqualifies my smog test because other codes were erased.now I have a car that is battery disconnect since I can't drive it due to not smog certified. All because of a rubber brake part falling off. I?called my dealer if it was covered by recall, they said no, even though there IS a recall for humid areas. I don't live in a humid area. So my case shows that it DOES NOT have to be humidity related. It's just a cheap quality part. I'm hoping this changes to include ALL areas. Thank you.

• Sep 10, 2025MD
  Back over prevention
  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that the rearview camera displayed a distorted image while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, which prevented the driver from safely operating the vehicle. The vehicle…

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that the rearview camera displayed a distorted image while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, which prevented the driver from safely operating the vehicle. The vehicle was not diagnosed or repaired. The contact stated that the failure persisted. The manufacturer was notified of the failure. The failure mileage was unknown.

• Mar 11, 2025OH96,000 mi
  Steering
  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that while turning to the left or right, the steering wheel was sticking. While driving at slow speeds in colder temperatures in a parking lot, the steering became inoperable. The steering wheel was difficult to turn. The message…

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that while turning to the left or right, the steering wheel was sticking. While driving at slow speeds in colder temperatures in a parking lot, the steering became inoperable. The steering wheel was difficult to turn. The message “Please pull over for Safety” was displayed. The contact turned off and restarted the vehicle. There were no warning lights illuminated. The contact stated that the failure was related to NHTSA Campaign Number: 19V632000 (Steering). The vehicle was taken to an independent mechanic who provided the contact with undisclosed error codes. The vehicle was taken to an undisclosed local dealer, where the codes were cleared, and the dealer informed the contact that the steering assembly needed to be replaced. The vehicle was reset, but the failure recurred. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 96,000.

• Oct 11, 2024NC76,000 mi
  Power train

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated while driving 20 MPH, there was an abnormal sound coming from the front of the vehicle. The vehicle was driven to the dealer to be diagnosed. The contact was informed that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and a case was opened. The failure mileage was approximately 76,000.

• Mar 3, 2023FL139,412 mi
  Power train
  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that while the engine was idling, there was an abnormal metal scraping sound coming from the vehicle. The vehicle was taken to the local dealer who diagnosed that metal shavings were discovered inside the transmission fluid, and that…

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that while the engine was idling, there was an abnormal metal scraping sound coming from the vehicle. The vehicle was taken to the local dealer who diagnosed that metal shavings were discovered inside the transmission fluid, and that the transmission needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 139,412.

• Aug 19, 2022IL117,000 mi
  Power train
  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that the vehicle rolled after parking. The gear shifter failed to move. The powertrain malfunction warning light was illuminated. The contact received notification of NHTSA Campaign Number: 22V413000 (Power Train) however, the part to…

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated that the vehicle rolled after parking. The gear shifter failed to move. The powertrain malfunction warning light was illuminated. The contact received notification of NHTSA Campaign Number: 22V413000 (Power Train) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The approximate failure mileage was 117,000. VIN tool confirms parts not available.

• Jun 1, 2022MS133,000 mi
  Power train
  The contact owns a 2014 Ford Fusion Hybrid. The contact stated while the vehicle was stationary, he was unable to move the gear shifter out of park(P). The contact stated no warning light was illuminated. The contact was able to temporarily repair the end of the shifter cable with a dog leash and…

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated while the vehicle was stationary, he was unable to move the gear shifter out of park(P). The contact stated no warning light was illuminated. The contact was able to temporarily repair the end of the shifter cable with a dog leash and drove to his residence. The contact called the local dealer and made them aware of the failure. The vehicle was not diagnosed or repaired. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 18V471000 (Power Train) and 19V362000 (Power Train) however, the VIN was not included. The manufacturer had not been informed of the failure. The failure mileage was approximately 133,000.

• May 9, 2022NY140,000 mi
  Steering
  The contact owns a 2014 Ford Fusion Hybrid. The contact stated while driving approximately 70 MPH, the vehicle jerked sharply to the right while the power steering assist warning light and other unknown warning lights illuminated. The contact mentioned that the power steering failed to function as…

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated while driving approximately 70 MPH, the vehicle jerked sharply to the right while the power steering assist warning light and other unknown warning lights illuminated. The contact mentioned that the power steering failed to function as needed. The vehicle was taken to the dealer but was not yet diagnosed. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 140,000.

• May 6, 2022GA129,000 mi
  Engine and engine cooling
  The contact owns a 2014 Ford Fusion Hybrid. The contact stated while driving at various speeds, the vehicle would start overheating after 15 minutes of driving. The contact stated that the engine temperature warning light was illuminated. The vehicle was taken to an independent mechanic to be…

  The contact owns a 2014 Ford Fusion Hybrid. The contact stated while driving at various speeds, the vehicle would start overheating after 15 minutes of driving. The contact stated that the engine temperature warning light was illuminated. The vehicle was taken to an independent mechanic to be diagnosed. The contact was informed that the transmission and water pump needed to be replaced. The vehicle was not repaired. The local dealer was contacted and notified of the failure; however, the contact was informed that the VIN was not under recall. The contact researched online and saw several complaints regarding the failure his vehicle had experienced. The manufacturer was not notified of the failure. The failure mileage was 129,000.

• Aug 11, 2020OK90,000 mi
  Steering
  TL* the contact owns a 2014 ford fusion hybrid. The contact stated that as she was pulling out of a bank parking, several unknown warning lights illuminated. The steering wheel ceased. The vehicle was taken to stuteville ford of atoka, llc (1601 s mississippi ave, atoka, ok 74525), and was…

  TL* the contact owns a 2014 ford fusion hybrid. The contact stated that as she was pulling out of a bank parking, several unknown warning lights illuminated. The steering wheel ceased. The vehicle was taken to stuteville ford of atoka, llc (1601 s mississippi ave, atoka, ok 74525), and was diagnosed that the power steering control module failed and needed to be replaced. The vehicle was not repaired. The contact mentioned that her husband was able to move the steering wheel and drove the vehicle to her residence. The manufacturer was made aware of the failure. The failure mileage was approximately 90,000.*dt*jb

• Jul 25, 2019TX111,000 mi
  Power train · Vehicle speed control
  TL* the contact owns a 2014 ford fusion hybrid. While driving 80 mph with the cruise control activated, the contact heard an abnormal noise and saw multiple unknown warning indicators illuminated. While attempting to park the vehicle on the side of the road and shifting the gear into park, the…

  TL* the contact owns a 2014 ford fusion hybrid. While driving 80 mph with the cruise control activated, the contact heard an abnormal noise and saw multiple unknown warning indicators illuminated. While attempting to park the vehicle on the side of the road and shifting the gear into park, the vehicle failed to stop and kept moving forward. The contact associated the failure with nhtsa campaign number: 18v471000 (power train). the contact had to apply the emergency brake to stop the vehicle. The vehicle was towed to the contact's residence and then towed to automax ford (located at 3301 e central texas expy, killeen, tx 76543, (888) 927-7951). The vehicle was not diagnosed or repaired. The manufacturer was notified. The failure mileage was 111,000.

• Jun 15, 2019OR49,700 mi
  Service brakes
  Leaving home in the morning, car started and ran normally, 1 block later, pressed brake pedal and it went all the way to the floor. had to really stand on it to stop the car. brake system, ABS, traction control, parking brake warning lights and messages all activated. parking brake locked up and…

  Leaving home in the morning, car started and ran normally, 1 block later, pressed brake pedal and it went all the way to the floor. had to really stand on it to stop the car. brake system, ABS, traction control, parking brake warning lights and messages all activated. parking brake locked up and the car had to be towed to dealer. replaced parking brake switch, rear brake pads, and rodent-chewed wiring. worked fine for a couple months. then, driving close to home about 35 mph, brakes failed again. standing on brake pedal stopped car in (estimated) double normal distance. all brake-related warning lights and messages activated, plus service rear park assist message. parking brake locked up. towed to dealer. service writer saw lights and messages, but techs later couldn't find malfunction, no codes set. dealership made no repairs, sent me home with a car I am afraid to drive. when asked if this IS a known issue, they pretended not to know, and didn't plan to contact ford about it. in my opinion, a software or electrical problem that causes the car to lose braking IS a pretty serious design flaw. according to nthsa database and internet forums, this IS a known issue, and something needs to be done before someone gets killed. at the very least, good-faith buyers should not be left holding the bag.

• Jun 8, 2019IN90,800 mi
  Unknown or other

  I was driving on the highway when my car shut off. No warning, it just shut off. I had to coast to the side of the road. After I put the car in park, it started back up with no problem.

• May 28, 2019FL100 mi
  Electrical system · Visibility/wiper

  The rear view backup camera fails. I have taken this vehicle to multiple dealerships totaling at least a dozen times for repair. The dealer has repeatedly been unable to repair this problem.

• Apr 25, 2019NV37,474 mi
  Structure › Body

  Front driver's door failed to latch. There IS no way to secure the door closed. This IS a life-threatening driving safety issue and theft issue there IS a recall already in place however my vin falls out of the previously announced range. The recall should be reopened and expanded.

• Apr 14, 2019TN
  Steering

  I was not informed by the manufacturer about this recall or when and how to get it repaired. I had to find out online myself when I was searching my vin.

• Apr 1, 2019NY
  Fuel/propulsion system · Unknown or other

  Emission recall14e02 which states vet may be equipped with an improperly functioning on-board emission-related diagnostic system that does not meet california standards and regulations, which also apply in massachusetts, maine, new york and vermont. Disabled emission-related monitors are unable to warn of an emission control malfunction. Vehicle when being operated smells and causes occupants to choke.

• Mar 28, 2019MA55,000 mi
  Power train
  TL* the contact owns a 2014 ford fusion hybrid. While driving at any speed, the transmission made a grinding noise. The vehicle was taken to kelly ford (420 cabot street, beverly, ma 01915, (888) 865-9541) where it was diagnosed that the gear shift was faulty and the transmission axle was leaking.…

  TL* the contact owns a 2014 ford fusion hybrid. While driving at any speed, the transmission made a grinding noise. The vehicle was taken to kelly ford (420 cabot street, beverly, ma 01915, (888) 865-9541) where it was diagnosed that the gear shift was faulty and the transmission axle was leaking. The dealer stated that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and stated that the vehicle's warranty had expired; therefore, they would not assist with the repair. The failure mileage was 55,000.

• Jan 27, 2019MD90,000 mi
  Power train

  This vehicle started overheating and the radiator IS leaking and it has been in for service regularly and nothing IS ever found. This IS an issue a lot of people have yet there IS no recall under my vin. I can not drive the car and it goes to limp mode, this car IS barely 5 years old

• Jan 23, 2019MD90,000 mi
  Structure › Body

  The hood will not open and it IS jammed and nothing was wrong with it before, the pieces are cheap and they shouldn't break like that

• Dec 21, 2018SC112,550 mi
  Vehicle speed control › Accelerator pedal

  Gas pedal completely broke off while I was driving in heat traffic on a rainy morning. no one at ford or the dealership shows any interest in replacing the defective plastic gas pedal; not to mention what happened. they act as though this IS a normal malfunction. *tr

• Nov 16, 2018CA72,000 mi
  Structure › Body

  TL* the contact owns a 2014 ford fusion hybrid. While accelerating from a stop, the contact heard a thumping noise. The vehicle was taken to an independent mechanic who determined that all three motor mounts were damaged and needed replacement. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The dealer was not notified. The approximate failure mileage was 72,000. *Tt*jb

• Jul 20, 2018MA130,000 mi
  Power train
  TL* the contact owns a 2014 ford fusion hybrid. While driving approximately 15 mph, the transmission failed. Prior to the failure, a loud "thump" sound was heard coming from the transmission. The contact immediately shifted the vehicle into first gear to "catch" the appropriate gear. Directly…

  TL* the contact owns a 2014 ford fusion hybrid. While driving approximately 15 mph, the transmission failed. Prior to the failure, a loud "thump" sound was heard coming from the transmission. The contact immediately shifted the vehicle into first gear to "catch" the appropriate gear. Directly afterwards, the emergency warning indicator illuminated and the "stop engine" message appeared. The vehicle was towed to an independent mechanic where the mechanic stated that the "wheels spin freely" and that the wheels would not remain in the park position. Imperial ford (8 uxbridge rd, mendon, mass, 01756, (888) 814-8373) was made aware of the failure. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 130,000.

• Jun 13, 2018IL35,000 mi
  Electrical system · Visibility/wiper
  The vehicle 'temporarily lost communication with the climate control ' basically the touchscreen freezes and none of the buttons on the center console work. Unable to turn on heat or air conditioning. The windows lock and can not be rolled up or down. This has happened while driving down free way…

  The vehicle 'temporarily lost communication with the climate control ' basically the touchscreen freezes and none of the buttons on the center console work. Unable to turn on heat or air conditioning. The windows lock and can not be rolled up or down. This has happened while driving down free way and also parked at start up. this occurrence has happened more than once. Sometimes the car will some how go back to normal after a day. The latest the vehicle has lost communication for 4 days. they say you can't leave a kid in the car while you go into a store, but ford can make it where I can't roll my widows down while driving and I have 2 kids in the car and it's 90 out. Even more when it's winter time and the widow fogs up while driving there IS no way to clear windows. To me it IS a safety hazard to not be able to at least roll your windows down or up because an issue happens with the vehicle communication.

• Apr 6, 2018CA
  Engine
  My car was making a load noise so I took it to a mechanic who referred me to the dealer because of the complexity of the vehicle. towed the car to morgan hill ford store in morgan hill california and was told that the engine was no good, that the motor bolts dislodged and melted causing the bolts…

  My car was making a load noise so I took it to a mechanic who referred me to the dealer because of the complexity of the vehicle. towed the car to morgan hill ford store in morgan hill california and was told that the engine was no good, that the motor bolts dislodged and melted causing the bolts to shred; the dealer service person ryan advised that the shredded metal got into the oil and went through my entire engine causing the engine fail. My car was only 3.5 years old, 90,000 miles but frequent oil changes with the extended maintenance package. There was no hint that the car was having issues, no engine light, nor the check oil light. I have a 2013 ford fusion that was recalled for faulty engine bolts.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Pedestrian alert sounds

  DP22005Opened Jan 27, 2023Closed Aug 7, 2023Recall 22V063000
  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…

  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

• Front Brake Jounce Hose Failures

  RQ22004Opened Aug 8, 2022Closed Mar 24, 2023Recall 23V162000
  On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the…

  On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturing on certain MY 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The result causes a brake fluid leak, lengthening the distance needing to stop the vehicle, increasing the risk of a crash.On March 10, 2023, Ford Motor Company (Ford) submitted to NHTSA Safety Recall 23V-162 (Ford Recall 23S12) to address front brake jounce hoses that may rupture. Ford found the rupture occurs from a localized failure of the internal reinforcement braid due to cyclic fatigue through tensile/bending and torsional inputs during suspension and steering articulations. The supplier for the front brake jounce hoses is Hitachi. This recall affects the subject vehicles equipped with non-hybrid engines and the suspect front brake jounce hoses (a total of 1,280,726 vehicles). The recall covers subject vehicles built from February 3, 2012 to July 19, 2017 when the suspect hoses were used in vehicle production. The remedy is for dealerships to replace both front brake jounce hoses with new hoses that have a revised braid material at no cost. The vehicles equipped with hybrid engines are excluded from the recall because the internal hose pressure is much lower due to the regenerative braking provided by the hybrid brake system. No failures of brake hoses on hybrid vehicles have been reported to ODI or Ford.Ford's actions address ODIs concerns at this time. Hybrid vehicles will be monitored for related failures. The agency reserves the right to take further action if warranted by new circumstances.The 103 ODI numbers cited above can be viewed at NHTSA.gov under the following ID numbers:11511014, 11510867, 11510318, 11509030, 11505993, 11504989, 11504400, 11502147, 11502082, 11501820, 11501283, 11498439, 11498296, 11496842, 11496335, 11494931, 11494851, 11494252, 11493001, 11492084, 11492070, 11491444, 11491274, 11488858, 11488027, 11487627, 11487416, 11487233, 11486150, 11484924, 11484526, 11484080, 11483948, 11483926, 11483739, 11483723, 11482773, 11482690, 11481077, 11480788, 11480294, 11480052, 11479338, 11479334, 11479252, 11479247, 11479187, 11479094, 11479048, 11478985, 11478953, 11478729, 11478216, 11476892, 11476282, 11470558, 11468994, 11467109, 11466294, 11462746, 11461217, 11456065, 11455367, 11444848, 11436419, 11436376, 11430685, 11428329, 11425083, 11421026, 11420738, 11420735, 11420298, 11418197, 11403926, 11397549, 11366991, 11366757, 11361016, 11359968, 11354569, 11352165, 11350344, 11348799, 11343929, 11343205, 11331947, 11329020, 11319596, 11310529, 11292271, 11288455, 11254787, 11253479, 11253244, 11234622, 11230669, 11230050, 11228240, 11221111, 11143630, 11129392 and 11120228.

• Desiccated Air Bag Inflator Rupture

  EA21002Opened Sep 17, 2021Open
  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…

  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

• Door Latch Failures

  RQ19005Opened Dec 19, 2019Closed Feb 7, 2022Recall 20V331000
  In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs…

  In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs reported the failure occurred after the latch had been remedied under a prior recall which involved fracture of the latch pawl spring tab due to thermally induced cyclic fatigue. Other VOQs alleged a similar failure in vehicles not previously recalled. A latch with a fractured pawl spring tab typically results in a ?door will not close? condition, however in certain somewhat rare circumstances, may result in the door coming open while driving. In response to ODI?s investigation, Ford has announced three field actions, as discussed below.On March 23, 2020, Ford submitted Safety Recall 20V-177 (Ford 20S15), a regional recall campaign to address door latch failures in vehicles not previously recalled under Safety Recalls 15V-246, 16V-643 and 17V-210. The recall affects vehicles currently or ever registered in certain high ambient temperature states (see 20V-177 for affected states). As a remedy, Ford will replace all four door latches free of charge.On August 24, 2020, Ford issued a non-safety regional field action (Ford 20R01) to address door latch failures on the same model/MY vehicles not covered under 20V-177 (i.e., not currently/ever registered in affected states). According to Ford, spring tab failure rates for vehicles covered by this action are about half that of the 20V-177 vehicles. Under this action, dealers will replace all door latches, free of charge, if either; a) the vehicle exhibits a related latch concern, or b) if the vehicle owner expresses a concern about the latches in their vehicles. Details can be found under NHTSA TSB No. 10190990, a copy of which is available in this investigative file available at NHTSA.gov.On June 8, 2020, Ford submitted Safety Recall 20V-331 (Ford 20S30) addressing vehicles previously remedied under NHTSA Recalls 15V-246, 16V-643 and 17V-210, where the repair may not have been properly completed, specifically not all of the door latches were replaced, or replaced correctly. This recall involves an inspection of the latches, with the option for a consumer self-inspection; owners could view the date codes on their latches (and confirm child safety locks are present on the rear doors) and then submit the information to Ford?s mobile app or website. A dealership inspection option was also available. Any vehicle found to have unreplaced defective latches requires the replacement of all door latches as directed by Ford.Regarding the 4,494 reports cited above, 1,485 involve scope-related failures (with 13% alleging door opening), and the remaining 3,009 reports involving remedy concerns (with 18% alleging door opening - note ODI was unable to verify the allegations of door opening). The three ODI injuries were all relatively minor. Ford?s reported injury incidences include one (unconfirmed) report of an ejection, three minor injuries with the others involving undisclosed injuries. Ford?s crashes involved two (unconfirmed) crashes alleging the incident door contacted another vehicle and three involving doors striking other property.The recalled vehicles include MY 2011-2015 Ford Fiesta, 2013-2016 Ford Fusion and Lincoln MKZ, 2015 Ford Mustang and Lincoln MKC, 2013-2015 Ford Escape and Ford C-MAX, 2012-2015 Ford Focus and 2014-2016 Ford Transit Connect.Ford's actions address ODI's concerns at this time. ODI will take further action if warranted by new information. The reference (OD

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
• 10233681Some 2014-2020 Fusion and 2017-2019 Escape vehicles may be equipped with a 1.5L Ecoboost engine that uses a 50-tooth variable camshaft timing (VCT) intake and exhaust unit from the assembly plant or if a service long block was installed. VCT locking tool 303-1097 is not compatible with this system. If VCT system service is required, replace both the intake VCT (service part DS7Z-6256-F) and exhaust VCT (service part DS7Z-6256-G) as a pair. An interim loaner tool program has been established to enable these repairs. Contact 1-800-403-4844 (Monday-Friday 8:00am to 8:00pm EST; Saturday 8:00am to 3:00pm EST) to obtain this tool. A VCT locking tool compatible with the 50-tooth system is under development and will be sent to dealerships. Continue to monitor OASIS for additional information.
• 10228876Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10226752Some 2013-2016 Escape/Fusion/MKZ vehicles may display an error message when updating the All Wheel Drive-ATC Barcode using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing.
• 10225458Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
• 10222788Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10218621Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10218617Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10214758Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10212957Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
• 10211728Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
• 10211709Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
• 10210730Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
• 10210392Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10209209This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
• 10204994Online automotive service information system for March 2016
• 10203848Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
• 10201614Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
• 10201034Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10199536Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
• 10194434Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
• 10189767Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
• 10181933This article supersedes 17-2225 to update the vehicle model years affected and Service Procedure. Some 2013-2014 Fusion and 2013-2020 MKZ vehicles may exhibit unintended exterior mirror movement in wet weather conditions. This may be due to water intrusion into the exterior mirror connector. To correct the condition, follow the Service Procedure steps to remove the 16 pin connector and install two weather tight 8 pin connectors.
• 10180428Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
• 10177863This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
• 10177123Some 2013-2016 Fusion/MKZ/C-MAX vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.
• 10176123Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
• 10175895Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
• 101719622013-2018 C-Max, 2013-2020 Fusion Hybrid/MKZ Hybrid vehicles may exhibit a MIL with Diagnostic Trouble Code (DTC) P0340 and/or P0344. This may occur due to excessive moisture build up in the engine oil. Excess moisture occurs when the vehicle is driven short distances and/or less than 6,000 combined miles per year. To correct the condition, replace the camshaft position sensor (CMP) and change the engine oil. Advise the customer to perform more frequent oil changes and allow the internal combustion engine to reach operating temperature when running to prevent reoccurrence. Refer to the owners guide - maintenance - engine oil check - operating in cold climates and short driving cycles.
• 10162068Some 2013-2017 C-Max/Fusion/MKZ Hybrid/Energi vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1450, P0456, P0457, P04EE and/or P04EF. This may be due to the sealing capability of the canister purge valve. To correct the condition, follow the Service Procedure steps to update the PCM software and replace the canister purge valve.
• 10144195Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
• 10074788Summary to be provided on a future date.
• 10058607Lincoln/ford: advance trac lamp or malfunction indicator lamp (mil) will be on with various diagnostic trouble codes (dtc) regarding evaporative emissions leak detection control module and possible replacement, if corrosion IS found. Model 2013-15 fusion, MKZ hybrid.
• 10058600Ford: when some vehicles are in EV mode or gas engine IS off, there IS a decreased, in performance and audio, of the subwoofer and needs latest calibration using ids version 96.02 or higher. Model 2014-16 fusion.
• 10058599Ford: decreased subwoofer performance or volume on fusion titanium hybrids. Update the audio digital signal processing module to correct problem
• 10057834Ford: no service action IS recommended for this condition. Please use at your discretion. Various 2010-2015 vehicles may experience a turbulence noise, similar to an helicopter noise, at highway speeds when the rear door window(s) or sunroof are open.
• 10056430Ford/lincoln: accompanied by the cmdtcs p1a18, p1a19, p0aee or p0bcd, the service engine soon lamp (energi) or wrench lamp (hybrid) will illuminate on some vehicles. Model 2013-2014 c-max, fusion, MKZ.
• 10056421Ford/lincoln: due to an adherence failure of rtv sealant, there IS a transmission fluid leakage, in some vehicles, from damper housing to transmission case joint. Model 2013 c-max, 2013-14 fusion, MKZ.
• 10056195Lincoln/ford: an investigation by engineers IS being done due to discharge from 12 volt battery and inspections of water pump connectors for corrosion or damage. Model 2013-2014 c-max, fusion hybrid, MKZ hybrid.
• 10056140Lincoln/ford: accompanied by cmdtc p1a18, p1a19, p0aee or p0bcd, the wrench lamp (hybrid) or service engine soon light may illuminate and the powertrain control module (pcm) needs to be reprogram to latest calibration. Model 2013-2014 fusion, MKZ.

Every Ford Fusion Hybrid model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.