2008 International 4400
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › International › 4400 › 2008
These records cover every 2008 International 4400. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2008 International 4400. Newest first.
Navistar, Inc. (Navistar) is recalling certain 2000-2003 International 8100, 2001-2003 International 9100i, 2001-2007 International 9400i, 2001-2010 International 9200i, 2002-2007, 2009 International 8500, 2003-2007, 2013 International 9900i, 2003-2018 International 8600, 2004, 2007 International 9900iX, 2008-2018 International ProStar, 2010-2011, 2013…
Risk and remedy
Risk
Low visibility or obstructed back up lights may not alert other drivers that the vehicle is backing up, increasing the risk of a crash.
Remedy
Dealers will replace the existing rear stop/turn signal lights, free of charge. Owner notification letters were mailed May 06, 2024. Owners may contact Navistar's customer service at 1-800-448-7825. Navistar's number for this recall is 23514.
On certain trucks, one or both rear axle housings may contain thinner material than what IS necessary for normal vehicle operation. over time, this thinner material may result in a fatigue failure of the rear axle housing, possibly in the location of the brake flange.
Risk and remedy
Risk
A crack in the brake flange location of the rear axle housing may result in a wheel end lockup or wheel separation possibly resulting in property damage, personal injury, or death.
Remedy
Dealers will inspect the vehicle's rear axles and, if necessary, replace the axle housings. the recall began on may 18, 2007. owners may contact international at 1-800-448-7815.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
- 10253979This document is to guide users to eliminate brake pedal rattle noise.
- 10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
- 10251409Suggested alignment target values when performing a vehicle axle alignment.
- 10246231J1939 Data Link Source Address Information
- 10243610How to request a horsepower quote; all International and Cummins engines
- 10243596General Wheel Speed Sensor Troubleshooting
- 10243595Diagnosis of chassis wander complaints.
- 10241555J1939 Data Link Source Address Information
- 10241554J1939 Data Link Troubleshooting
- 10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
- 10227455J1939 Data link source address information
- 10222490Pico Scope CCOS (Crankcase Separator Test)
- 10219330PicoScope Test One Channel RCT
- 10219325PicoScope Test Resistance and Ohmmeter
- 10219319PicoScope Test for Datalink (CAN) Health Shorts & opens
- 10219314PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
- 10209487Calculating pulses per mile (speedometer setting); only models equipped with International engines
- 10208432ECM Calibration for DPF Replacement; Applies to MaxxForce Engines
- 10208431J1939 Data Link Source Address Information
- 10204139Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- 10204137J1939 Data Link Troubleshooting
- 10204136Dual Drive Cab Throttle Position Harness for APS/IVS throttle pedals; only models with both left hand and right hand drive.
- 10204134WABCO Full Power Brake Diagnostic Code (DTC) Index
- 10202873How to program parameters after changing WABCO FPB ECU (Parking brake shows N/A)
- 10201758Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
- 10199915General wheel speed sensor troubleshooting
- 10198708Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- 10189743Suggested alignment target values when performing a vehicle axle alignment
- 10189741Frame Rail Straightness Inspection Procedure
- 10185108ECM Calibration for DPF Replacement; only trucks and busses built with 2007- 2009 MaxxForce DT/9/10. 2010-2012 MaxxForce DT/9/10, 2007-2009 MaxxForce V8, 2008-2009 MaxxForce 11/13 engines
- 10181960Cab Lean Concern
- 10179294Driveline Information Center and Troubleshooting Procedures
- 10179289Repair Procedures for Vehicles Struck by Lightning
- 10177096A/C Refrigerant and Oil Capacities
- 10173025Cleaning and Disinfecting Trucks and Buses
- 10172045J1939 Data Link Troubleshooting
- 10170952Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
- 10169879Key Codes and Key Cutting Information (Not for CV Series)
- 10166287Converting 4000 4 X 2 HPV Models with Hydraulic ABS Brakes to 4 X 4 Configuration may Increase Stopping Distance and is Not Approved by International Truck and Engine Corporation and Merritor Wabco
Every International 4400 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.