2008 Mercedes Benz C300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes Benz › C300 › 2008
These records cover every 2008 Mercedes Benz C300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2008 Mercedes Benz C300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2010 E350, 2014 G550, 2008-2009 C300, 2008 C350, 2009 CLK550, 2007 SL550, SLK280, and 2008 SLK350 vehicles. Various control units may have been updated with incorrect software configuration during a service repair. This can result in various system failures, such as loss of drive power, reduced exterior…
Risk and remedy
Risk
Various system failures, such as loss of drive power, reduced exterior lighting, or loss of dynamic control functions including stability and traction control, can increase the risk of a crash.
Remedy
Dealers will update the software configuration on the affected control units, free of charge. Owner notification letters were mailed May 3, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…
Risk and remedy
Risk
If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2008-2011 C300 Sedan, C300 4matic Sedan, C350 Sedan, C63 AMG Sedan vehicles, 2010-2011 GLK350, GLK350 4-Matic and E350 Coupe vehicles, 2011 SLS AMG, E350 Convertible, E550 Coupe and E550 Convertible vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag modules, free of charge. Owners were sent an interim notification October 2016. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2009-2010 ML320 BlueTec 4Matic, GL320 BlueTec 4Matic and R320 CDI 4Matic, 2011 E350 Cabriolet and E550 Cabriolet, 2009-2011 ML350, ML350 4Matic, ML550 4Matic, ML63 AMG, and C63 AMG, 2010-2011 ML450 4Matic Hybrid, E350 Coupe, E350 4Matic, E550 Coupe, E550 4Matic, and E63 AMG, 2011-2012 GL350…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
MBUSA will their notify owners, and Fiat Chrysler will notify the affected Chrysler owners. Dealers for the respective brands will replace the driver's frontal air bag module, free of charge. This recall began November 2016. Mercedes-Benz owners may contact MBUSA customer service at 1-800-367-6372 and Chrysler owners may contact Fiat Chrysler customer service at 1-800-853-1403.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2008-2009 C300 Sedan, C300 4Matic, C63 AMG, and C350 vehicles, and 2010 GLK350 and GLK350 4Matic vehicles. Due to a manufacturing error, the air bag control unit may corrode and cause the control unit to malfunction.
Risk and remedy
Risk
The malfunctioning air bag control unit may cause the air bags to unexpectedly deploy increasing the risk of injury and the possibility of a vehicle crash. Alternatively, the air bag control unit malfunction may cause the air bags to not deploy in the event of a crash necessitating air bag deployment, increasing the risk of occupant injury.
Remedy
MBUSA will notify owners, and dealers will inspect the air bag control unit and replace it, as necessary, free of charge. Mercedes-Benz issued an interim notification to owners on December 23, 2015. The recall began on March 14, 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (Mercedes) is recalling certain model year 2008-2011 C300, C300 4Matic, C350, and C63 AMG vehicles manufactured January 26, 2007, through July 13, 2011. In the affected vehicles, a poor electrical ground connection may result in the dimming or failure of the tail lights.
Risk and remedy
Risk
Dimming or failure of the tail lights reduces the ability to warn other motorists of the driver's intentions of stopping or turning, increasing the risk of a crash.
Remedy
Mercedes will notify owners, and dealers will replace the bulb holders if not previously updated and replace any corroded connectors, free of charge. The recall began on August, 18, 2014. Owners may contact Mercedes at 1-800-367-6372.
Owner complaints
672 complaints20 involved a crash16 involved a fire27 injuries
What owners report most
Latest complaints
- Service brakes, hydraulic
The contact owns a 2008 Mercedes-Benz C300. The contact stated that while depressing the brake pedal, attempting to stop, the vehicle failed to respond as intended and causing the contact to drive through a stop sign, then merge onto the interstate independently. The driver's side rear tire was…
The contact owns a 2008 Mercedes-Benz C300. The contact stated that while depressing the brake pedal, attempting to stop, the vehicle failed to respond as intended and causing the contact to drive through a stop sign, then merge onto the interstate independently. The driver's side rear tire was leaking brake fluid. The check brake system warning light illuminated. The vehicle was towed to a dealer, where it was diagnosed that the brake line was corroded. The vehicle was repaired under warranty for the subframe prior to the failure; however, the brake lines were not covered and needed replacement. The vehicle was then towed to an independent mechanic where the brake lines were pending replacement; however, the mechanic was waiting for parts. The manufacturer was notified of the failure and offered no assistance. The approximate failure mileage was 164,000.
- Electrical system · Exterior lighting
The contact owns a 2008 Mercedes-Benz C300. The contact stated while at the car wash and attempting to wash the vehicle, there was popping sound coming from the vehicle, and the contact saw smoke coming from the speakers and called the Fire Department however, no damages were found. The vehicle was…
The contact owns a 2008 Mercedes-Benz C300. The contact stated while at the car wash and attempting to wash the vehicle, there was popping sound coming from the vehicle, and the contact saw smoke coming from the speakers and called the Fire Department however, no damages were found. The vehicle was taken to the residence and an independent mechanic inspected the vehicle but found no issues with the vehicle. The trunk was opened, and the contact became aware of water inside the taillight housings. No warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic to be diagnosed. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 180,000.
- Service brakes
Certified Mercedes dealership confirmed that the subframe of my 2008 C300 is rusted and needs to be replaced which is under warranty. However, they are unwilling and do not acknowledge that the brake lines are also rusted and need to be replaced which is CAUSED by the rusted subframe. I first…
Certified Mercedes dealership confirmed that the subframe of my 2008 C300 is rusted and needs to be replaced which is under warranty. However, they are unwilling and do not acknowledge that the brake lines are also rusted and need to be replaced which is CAUSED by the rusted subframe. I first consulted my local mechanic shop who specializes in Mercedes repairs, and he told me about the issues of the corroding subframe and the rested brake lines. He also mentioned that he has helped and directed many Mercedes owners to call Mercedes customer service to voice my concerns as well as confirm the warranty of the subframe.
- Electrical system
The contact owns a 2008 Mercedes-Benz C300. The contact stated that upon turning off the vehicle, there was an abnormal clicking sound coming from the vehicle. There was no warning light illuminated. The contact stated that the following day, the vehicle failed to start after several attempts and…
The contact owns a 2008 Mercedes-Benz C300. The contact stated that upon turning off the vehicle, there was an abnormal clicking sound coming from the vehicle. There was no warning light illuminated. The contact stated that the following day, the vehicle failed to start after several attempts and required a jumpstart. The contact replaced the battery; however, the failure persisted. The contact disconnected the battery to prevent the battery from draining. The dealer and the manufacturer were not yet notified of the failure. The vehicle was not repaired. The failure mileage was approximately 200,000.
- Engine and engine cooling
The contact owns a 2008 Mercedes-Benz C300. The contact stated while driving 45 MPH and depressing the accelerator pedal, the vehicle slowed down independently and lost automotive power. The contact stated that the vehicle remained in the intersection while awaiting tow services. The contact stated…
The contact owns a 2008 Mercedes-Benz C300. The contact stated while driving 45 MPH and depressing the accelerator pedal, the vehicle slowed down independently and lost automotive power. The contact stated that the vehicle remained in the intersection while awaiting tow services. The contact stated that her boyfriend and son helped to push the vehicle to the right side of the roadway. The contact smelled a burning odor but was unsure where the odor was coming from. No warning light was illuminated. The contact stated that an independent mechanic was contacted. The vehicle was towed to an independent mechanic where it was diagnosed that the ECU was damaged and needed to be replaced. The vehicle was repaired. The contact related the failure to NHTSA Campaign Number: 24V704000 (ENGINE AND ENGINE COOLING); however, the VIN was not included in the recall. The manufacturer was not notified of the failure. The approximate failure mileage was 110,000.
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2008 Mercedes Benz C300. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 125,985, and at the time of registration, it was discovered that the mileage was 128,917.
- Steering
On [XXX] the car refused to start due to the electronic steering lock failure. The car was towed to the nearest Mercedes Benz Dealer at Stevens Creek Blvd, San Jose CA 95129. An inspection was done and Mercedes Benz wanted $3457.66 to replace the Steering Lock. This item is a recall item in other…
On [XXX] the car refused to start due to the electronic steering lock failure. The car was towed to the nearest Mercedes Benz Dealer at Stevens Creek Blvd, San Jose CA 95129. An inspection was done and Mercedes Benz wanted $3457.66 to replace the Steering Lock. This item is a recall item in other years of the C300 Mercedes Benz. Google shows: Mercedes-Benz has issued a recall for the Mercedes- Benz C-Class models, including the C300, due to potential steering lock issues. The recall specifically affects 2015- 2016 C300 models, as well as other C-Class variations like the 2017-2019 C300 Cabrio and Coupe. The recall is due to a potential problem with the Electronic Steering Lock (ESL) module, which is responsible for locking and unlocking the steering wheel. A faulty ESL module can prevent the steering wheel from unlocking, causing the vehicle to be unable to start. We feel that the recall should also apply to the C300 2008 model as it is exactly the same issue and completely incapacitates the car and is a danger to the public as involves the electronic steering. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system · Exterior lighting · Power train
The vehicle has been loosing power during driving. Acceleration will die, then power will return. In addition exterior lighting will also malfunction or not work. As well ans other items associate with power or the unit that controls the power of those items After taking the vehicle in multiple…
The vehicle has been loosing power during driving. Acceleration will die, then power will return. In addition exterior lighting will also malfunction or not work. As well ans other items associate with power or the unit that controls the power of those items After taking the vehicle in multiple times we had been told and looked up about the recall. Multiple are in place but the recall regarding the electrical/ power train / lighting r/t units in place and this recall sounds spot on with issues the vehicle is having .
- Electrical system · Steering
The contact owns a 2008 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the steering wheel failed to turn in the intended direction. The contact stated that a message to remove the ignition key was displayed. The vehicle was driven to the residence. The contact…
The contact owns a 2008 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the steering wheel failed to turn in the intended direction. The contact stated that a message to remove the ignition key was displayed. The vehicle was driven to the residence. The contact stated that later, while starting the vehicle, the vehicle failed to start as intended. In addition, the contact stated the steering wheel had seized. The contact inspected the battery and determined there was no failure with the battery. The vehicle was taken to the dealer; however, the vehicle was not diagnosed. The contact was requested to pay a diagnostic fee and declined. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to take the vehicle to the dealer for a diagnostic test. The failure mileage was approximately 90,000.
- Engine · Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
The contact owns a 2008 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. Additionally, the check engine warning light was illuminated. The vehicle was taken to the dealer where…
The contact owns a 2008 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. Additionally, the check engine warning light was illuminated. The vehicle was taken to the dealer where it was diagnosed with an intake manifold failure. The contact was informed that the intake manifold needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 152,151.
- Electrical system · Engine
Camshaft adjuster solenoid leaked oil into wiring harness, caused vehicle to go into limp mode and not accelerate/shift gears. This is a known problem with the m272 engine, this vin did not show up on the recall list.
- Steering
ESL failed suddenly. This appears to be a common problem with C300 MB. As such it should be part and f a recall as the expense to replace is over $2000.
- Service brakes
I honestly don’t know how Mercedes could have used such a cheap metal mix in their brake lines. Every single c300 made before 2012 is at extreme risk of brake failure every winter, the lines rust very easily and cause ruptures to happen as soon as you need to use your brakes in emergency. If you slam your foot on the brakes for a 2008-2009 Mercedes, you are putting your life at risk.
- Air bags
The airbag headrests opened up randomly without being involved in an accident!
- Air bags
The contact owned a 2008 Mercedes-Benz C300. The contact received notification of NHTSA Campaign Numbers: 16V081000 (Air Bags) and 16V363000 (Air Bags) and would like to be removed from the recall distribution list. The local dealer was not contacted. The manufacturer was contacted.
- Air bags · Exterior lighting
The contact owns a 2008 Mercedes-Benz C300. The contact stated after the vehicle was taken to the dealer for an unknown recall repair, the air bag warning light remained illuminated. The contact also became aware that the driver’s side headlight was inoperable. The vehicle was taken back to the…
The contact owns a 2008 Mercedes-Benz C300. The contact stated after the vehicle was taken to the dealer for an unknown recall repair, the air bag warning light remained illuminated. The contact also became aware that the driver’s side headlight was inoperable. The vehicle was taken back to the dealer where it was diagnosed with a detached headlamp wiring harness. The dealer recommended that driver’s and passenger’s side headlamps be replaced. Additionally, the taillights remained illuminated after turning off the vehicle. The vehicle was not repaired. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was unknown.
- Suspension
My rear suspension, right lower control arm I believe it's called. Snapped out of the subframe do to corrosion . My hole rear subframe is getting worse, eating up by corrosion
- Air bags · Electrical system · Seat belts
Car has been in and out of the shop. Initially I have been contacting Mercedes about airbag messages and continued message of SRS Malfunction on dashboard. Airbags had been recalled and supposedly replaced on multiple occasions. This SRS continues to remain even after repair or being seen for this…
Car has been in and out of the shop. Initially I have been contacting Mercedes about airbag messages and continued message of SRS Malfunction on dashboard. Airbags had been recalled and supposedly replaced on multiple occasions. This SRS continues to remain even after repair or being seen for this issue only for other components to have failed and me having to pay for those in the process. The SRS Malfunction remains an issue until the next issue is affected. Recently an entire Electronic SAM Module Component was replaced as the culprit only to have more issues and the SRS remained. Mercedes has contended that each time they saw the vehicle the the SRS Malfunction was not the problems while other documents were repaired such as battery and SAM. In the meantime since then the car has stalled, components that were working are no longer inoperable. There was a recall that was applied to only specific vehicles of my model year which state the SRS Malfunction was to be replaced and made whole. I never received one of those notices and I will note that my vehicle obviously was affected and should also have this component replaced as it fits the same model year and make of the issues Mercedes has repaired already on affected vehicles. This issue has been on going for several years and Mercedes has failed to rectify this component that makes it dangerous and causes safety concerns for us with the understanding that their note on their website about the SRS Malfunction appeared to me a cop out for them to not be responsible for the fix and recall thsr may have affected more vehicles than its originally accessed number. Instead of fixing this issue they continually find other repairs they indicate as the issue only to end up right back with the same SRS Malfunction and stalling issues with vehicle once again and want to use excuse of car's age as issue and failing to acknowledge and address the SRS Malfunction. Your system would not allow file upload. I can still provide
- Electrical system
The contact owns a 2008 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, the vehicle lost motive power. The contact stated that an unknown warning light was illuminated. The contact was able to restart the vehicle and drove the vehicle a short distance before the…
The contact owns a 2008 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, the vehicle lost motive power. The contact stated that an unknown warning light was illuminated. The contact was able to restart the vehicle and drove the vehicle a short distance before the vehicle lost motive power again. The vehicle was towed to the residence. The contact stated while the vehicle was sitting in the driveway, the vehicle independently started and accelerated. The contact stated that the battery terminals were disconnected. The vehicle was towed to the dealer where it was diagnosed with failed wiring harness. The contact was informed that the wiring harness needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure but did not assist. The failure mileage was approximately 171,846.
- Suspension
My car has a rotten rear subframe and has holes in it and the dealer doesn't want to repair it and Mercedes announced that it had a 20 year extended warranty. I'm from Manchester, New Hampshire. They inspected it and say they can't change it for free. The warranty doesn't cover it. I don't know what's going on. with that
- Electrical system · Engine · Steering
Car worked fine, all the sudden it wouldn't turn over, I would put the key in and turn it and nothing would happen, I was stuck and had to catch a ride, lucky that I was able, a car company that is supposedly reliable shouldn't allow there cars to completely give out on people during the middle of…
Car worked fine, all the sudden it wouldn't turn over, I would put the key in and turn it and nothing would happen, I was stuck and had to catch a ride, lucky that I was able, a car company that is supposedly reliable shouldn't allow there cars to completely give out on people during the middle of winter storms and not take ownership, when the customer has taken good care of the car. Talked to several mechanics and turned out it was the Electronic Steering Lock (ESL) module that had malfunctioned probably due to the software and electrical. Due to this only the Benz dealerships can repair, I had to tow it to a dealership and was charged around $2000 after haggling over the price. Terrible experience and should be recalled by MB, I have seen many complaints about this online and was very disappointed there wasn't a cheaper solution. Was both a safety issue, inconvenient and very costly.
- Suspension
rear subframe corrodes and detaches from car. a class action lawsuit has been filed in georgia and california. this effects many mercedes models. dealer stated the lawsuit extends to 08 models as well.
- Service brakes
Brake Booster vacuum leak causing it to not brake properly. Requires more pedal pressure to come to a stop. Extremely dangerous
- Unknown or other
Recalls need to be fixed.
- Air bags
My car had the Takata airbags that were recalled. It says the recalls were repaired but my vehicle is saying that the driver-side airbag has malfunctioned. I haven't been in any accidents. So I contacted Mercedes and they could not find verification that the previous open recalls were ever fixed.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Loss of rear lighting assembly
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish…
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
- Loss of rear tail light functionality
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed…
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10235996Additional information around the recent recall announcement affecting approximately 705,983 Mercedes-Benz passenger vehicles involving Takata driver-side airbags containing PSDl-5 type inflators
- 10235983Daimler AG (DAG) has decided that a supplier production error in the SRS control unit could lead to a failure of the SRS control unit. This malfunction of the SRS control unit would illuminate the SRS warning lamp and subsequently deactivate the SRS components. Additionally, in the event one specific electrical connection is interrupted, several SRS components could inadvertently deploy, increasing the risk for injury.
- 10235978Recall Campaign announcement for Takata driver airbags.
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
- 10205265Outside mirror fogged.
- 10205239"Anti-theft protection activated".
- 10205233Mobile phone cotacts are not transferred completely.
- 10205225Headlamps fogged.
- 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
- 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
- 10181124Harsh engagement when changing gear range from P to D or R
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167560Fault message in display - Right rear turn signal light inoperative
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167552Engine does not start, or various fault messages in instrument cluster immediately after engine start and servo assistance is reduced. The following display messages may appear: - Red message "Power Steering Malfunction - See Operator's Manual" including acoustic warning - Red or yellow message "ESP / ABS Currently Unavailable - See Owner's Manual", sometimes with acoustic warning - White message about tire pressure monitor or run flat indicator: "Tire Pressure Loss Warning Defective" or "Tire Pressure Monitor Defective" In addition, the indicator lamps of the following systems may light up: - Brakes / ABS / ESP / ESP Off / engine diagnosis Furthermore: - The chassis CAN is partially or completely disrupted - Several control units (e.g. the electric power steering, ESP, engine etc.) cannot be interrogated or are not listed in the quick test - Various CAN communication errors from other control units may be logged (see list "Control unit / Fault code")
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
- 10167536Model X204 (GLK 250 BT) with AMG Styling Package 321. Model Year 2013 Install Tire Fit Kit, Replace Monroney Label
- 10167532A production fault means that the telematics DVD A 166 827 14 00 cannot be used. Because of this the previous telematics DVDs A 204 827 03 65 and A 204 827 10 65 must continue to be used for control unit programming. If required, these are still available for ordering. With XENTRY DVD 03/2014 a new telematics DVD with part number A 166 827 21 00 is being shipped. This telematics DVD replaces the previous telematics DVDs.
- 10167525Apple products (iPhone or iPod) are not charged via the serial USB interface of the COMAND Online control unit (A40/3) in the stowage compartment of the center console.
- 10167510The vehicle cannot be started The vehicle may start by itself shortly after the startup attempt with a delay, as the relay can be late closing. and/or The gear selection is displayed, but no gear is engaged. Gear selection is not possible. and/or Rear window wiper inoperative. and/or Various fault codes concerning disrupted communication paths are stored and/or the corresponding control units are not displayed in the quick test. Affected control units include the transmission control unit, electronic ignition lock, driver SAM, engine control unit, Lane Keeping Assist, Distronic.
- 10167489Noise: A rattling noise may be heard from the area of the chain drive for approx. 2-5 seconds after engine start. And/or: Fault code entries in engine control unit: SIM271DE20: P001177 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. P001762 The position of the exhaust camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. The signal comparison is faulty. P001192 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The function or the instruction is faulty. P001195 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The mechanical setup is not OK. P001477 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. P001492 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The function or the instruction is faulty. P001495 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The mechanical setup is not OK. P001600 The position of the intake camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. P001662 The position of the intake camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. The signal comparison is faulty. P001700 The position of the exhaust camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft.
- 10167040This Service Campaign has been initiated because Daimler AG (DAG), the manufacturer of Mercedes-Benz vehicles, has determined that the mbrace software does not correspond to current production configuration. An authorized Mercedes-Benz dealer will update the mbrace control module software at the next workshop visit.
Every Mercedes Benz C300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.