2009 Mercedes Benz C300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes Benz › C300 › 2009
These records cover every 2009 Mercedes Benz C300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2009 Mercedes Benz C300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2010 E350, 2014 G550, 2008-2009 C300, 2008 C350, 2009 CLK550, 2007 SL550, SLK280, and 2008 SLK350 vehicles. Various control units may have been updated with incorrect software configuration during a service repair. This can result in various system failures, such as loss of drive power, reduced exterior…
Risk and remedy
Risk
Various system failures, such as loss of drive power, reduced exterior lighting, or loss of dynamic control functions including stability and traction control, can increase the risk of a crash.
Remedy
Dealers will update the software configuration on the affected control units, free of charge. Owner notification letters were mailed May 3, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 C250, C250 Coupe, C350 Coupe 4Matic, C300 4Matic, C350, C350 Coupe, C63 AMG, C63 Coupe, E350 Cabrio, E350 Coupe, E550 Cabrio, E350 Coupe 4Matic, E550 Coupe, GLK350 4Matic, GLK250 Bluetec 4Matic, GLK350, SLS Coupe, SLS AMG GT Coupe, and SLS Roadster vehicles sold, or ever registered, in the states of…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. Mercedes issued an interim notification to owners on February 23, 2018. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…
Risk and remedy
Risk
If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2008-2011 C300 Sedan, C300 4matic Sedan, C350 Sedan, C63 AMG Sedan vehicles, 2010-2011 GLK350, GLK350 4-Matic and E350 Coupe vehicles, 2011 SLS AMG, E350 Convertible, E550 Coupe and E550 Convertible vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag modules, free of charge. Owners were sent an interim notification October 2016. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2009-2010 ML320 BlueTec 4Matic, GL320 BlueTec 4Matic and R320 CDI 4Matic, 2011 E350 Cabriolet and E550 Cabriolet, 2009-2011 ML350, ML350 4Matic, ML550 4Matic, ML63 AMG, and C63 AMG, 2010-2011 ML450 4Matic Hybrid, E350 Coupe, E350 4Matic, E550 Coupe, E550 4Matic, and E63 AMG, 2011-2012 GL350…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
MBUSA will their notify owners, and Fiat Chrysler will notify the affected Chrysler owners. Dealers for the respective brands will replace the driver's frontal air bag module, free of charge. This recall began November 2016. Mercedes-Benz owners may contact MBUSA customer service at 1-800-367-6372 and Chrysler owners may contact Fiat Chrysler customer service at 1-800-853-1403.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2008-2009 C300 Sedan, C300 4Matic, C63 AMG, and C350 vehicles, and 2010 GLK350 and GLK350 4Matic vehicles. Due to a manufacturing error, the air bag control unit may corrode and cause the control unit to malfunction.
Risk and remedy
Risk
The malfunctioning air bag control unit may cause the air bags to unexpectedly deploy increasing the risk of injury and the possibility of a vehicle crash. Alternatively, the air bag control unit malfunction may cause the air bags to not deploy in the event of a crash necessitating air bag deployment, increasing the risk of occupant injury.
Remedy
MBUSA will notify owners, and dealers will inspect the air bag control unit and replace it, as necessary, free of charge. Mercedes-Benz issued an interim notification to owners on December 23, 2015. The recall began on March 14, 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (Mercedes) is recalling certain model year 2008-2011 C300, C300 4Matic, C350, and C63 AMG vehicles manufactured January 26, 2007, through July 13, 2011. In the affected vehicles, a poor electrical ground connection may result in the dimming or failure of the tail lights.
Risk and remedy
Risk
Dimming or failure of the tail lights reduces the ability to warn other motorists of the driver's intentions of stopping or turning, increasing the risk of a crash.
Remedy
Mercedes will notify owners, and dealers will replace the bulb holders if not previously updated and replace any corroded connectors, free of charge. The recall began on August, 18, 2014. Owners may contact Mercedes at 1-800-367-6372.
Owner complaints
576 complaints14 involved a crash18 involved a fire13 injuries
What owners report most
Latest complaints
- Air bags · Electrical system · Exterior lighting
I have messages on my instrument panel stating I have airbag malfunction going on I also have tail lights that are not working and after trying to replace the bulbs it still don't work so obviously it's the light bulb panel so I went and looked at recalls and says that these are all recalls on my car but that they were fixed. so I don't know why I have them all bad again so I need to know what to do
- Electrical system
The contact owns a 2009 Mercedes-Benz C300. The contact stated that while starting the vehicle, the check engine, seat belt, and air bag warning lights illuminated. Additionally, the headlights and navigation lights failed to activate for a while. There was burning odor inside the vehicle with the…
The contact owns a 2009 Mercedes-Benz C300. The contact stated that while starting the vehicle, the check engine, seat belt, and air bag warning lights illuminated. Additionally, the headlights and navigation lights failed to activate for a while. There was burning odor inside the vehicle with the heat activated or turned off. The contact also stated the vehicle failed to start for three days before eventually being able to start. The contact attempted to charge the battery, which resulted in a visible spark. The vehicle was taken to a dealer where it was diagnosed with a sound module and the Signal Acquisition Module (SAM) failures. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 217,000.
- Structure › Body
Vehicle inspection by independent service center indicated that a new rear frame was necessary. This was the second communication to nhtsa on this issue. This automobile (2009 c300) is inoperable due to this Mercedes rear frame defect .
- Steering
The problem is that the steering wheel locking mechanism has failed. The vehicle could not be started or driven. It required a flatbed tow to an authorized Mercedes repair facility. It was diagnosed as the steering mechanism, requiring replacement. The cost for this repair is $1400.00. I…
The problem is that the steering wheel locking mechanism has failed. The vehicle could not be started or driven. It required a flatbed tow to an authorized Mercedes repair facility. It was diagnosed as the steering mechanism, requiring replacement. The cost for this repair is $1400.00. I researched this problem on the MB website and it stated that this issue was common. I feel that this is a safety issue and should be repaired free of charge or at a significant discount. The car is currently being repaired, and I can forward any relevant documentation to you once the repair is complete.
- Electrical system
While driving the car on [XXX] at 9pm on sunday, [XXX] in lane two during a heavy rain a audible clicking noise came from the drivers side front of the dash instrument cluster area and all of the lights on the car simultaneously turned off without ever touching the light switch i was unable to…
While driving the car on [XXX] at 9pm on sunday, [XXX] in lane two during a heavy rain a audible clicking noise came from the drivers side front of the dash instrument cluster area and all of the lights on the car simultaneously turned off without ever touching the light switch i was unable to see the road in front of the vehicle also the windshield wipers quit working and the radio and navigation display went off and closed and opened and closed( turned off and then on and off again) the instrument cluster went dark as well, luckily i was able to turn the steering and apply the brakes and steer the vehicle onto the shoulder of the road and come to a complete stop after several attempts to turn the headlights back on i determined that the vehicle was not safe to drive , and had the vehicle towed to a reputable mechanic, and upon diagnosis he contacted me and stated that the drivers side front signal acquisition module A. K. A. the (sam) module had failed due to water intrusion into the fuse panel sam module area , the mechanic stated that i should file an incident /complaint form with your office , upon searching the MERCEDES BENZ forums and sites on the www i found many customers with a broad range of models (w204)approximately this same year model have identical complaints and nothing has been done by MB usa to remedy the problem, i believe this matter to be a major safety concern and i am wondering why this matter hasnt been taken into consideration by your agency and by MB usa as a safety recall to replace the failing modules and retrofit the fuse panel sam module area to prevent water intrusion thats causing the obvious safety concern and possible liability on the part of the MB/ DAIMLER corporation. it seems this is clearly a problem and it needs fixed we are terrified to drive the vehicle for fear of a repeat incident. Sincerely the [XXX] family INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system · Exterior lighting · Unknown or other
Check Right Tail and Brake Lamps warning light will not go off for months. They are working fine but the light won't go off. Googling on MB World, it shows Mercedes is aware of this problem and a recall is needed to get it corrected being safety issue with warning lights not working properly. See…
Check Right Tail and Brake Lamps warning light will not go off for months. They are working fine but the light won't go off. Googling on MB World, it shows Mercedes is aware of this problem and a recall is needed to get it corrected being safety issue with warning lights not working properly. See all info. below from owners, conversations and work done by dealers, etc. People note it is a middle school education problem. Please alert me when the recall is confirmed to get this important problem fixed. [XXX] Thank you, [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Service brakes
Went to the Mercedes dealership service department to replace the rear subframe that suddenly broke while I was driving due to extreme rust/corrosion. The dealership stated that it was being covered under the extended warranty due to the recall related to the rust/corrosion issue with the…
Went to the Mercedes dealership service department to replace the rear subframe that suddenly broke while I was driving due to extreme rust/corrosion. The dealership stated that it was being covered under the extended warranty due to the recall related to the rust/corrosion issue with the subframe. I was advised by the mechanic that the brake lines will need to be replaced due to extreme rust/corrosion in the rear at the same exact location of the rear subframe, making the vehicle very dangerous to drive because the brake lines could break at any moment and cause sudden brake failure. I was quoted a very significant amount to replace the rusted brake lines and per the dealership, it will not be covered under any extended warranty and/or recall.
- Structure
The contact owns a 2009 Mercedes-Benz C300. The contact stated that while driving at various speeds, the rear end of the vehicle would fishtail and become extremely unstable while driving over a bump in the road or while turning. Upon inspection, the contact discovered that the subframe was…
The contact owns a 2009 Mercedes-Benz C300. The contact stated that while driving at various speeds, the rear end of the vehicle would fishtail and become extremely unstable while driving over a bump in the road or while turning. Upon inspection, the contact discovered that the subframe was severely rusted. The cause of the failure was not determined, and the vehicle was not yet repaired. The local dealer was notified of the failure. The manufacturer was not contacted. The failure mileage was 201,000.
- Electrical system · Power train · Steering
I drove my car to get lunch. Came back out to go back to work and the car would not start. Would not even turn over. My Radio did not turn on and I couldn't even roll my windows back up. Luckily they were only cracked open a small amount. My steering wheel cannot be turned, it's locked in it's…
I drove my car to get lunch. Came back out to go back to work and the car would not start. Would not even turn over. My Radio did not turn on and I couldn't even roll my windows back up. Luckily they were only cracked open a small amount. My steering wheel cannot be turned, it's locked in it's current position. I am told the ESL (Electronic Steering Lock) and possibly the EIS is the cause of this problem. The display on the dash says "Take your key from ignition" and that is all I get. Had to have my car towed and now I have a dead car with the windows partially open that I cannot close.
- Electrical system · Exterior lighting
Headlight harness on drivers and passenger side is melting and my lights are flickering. I was advised to night drive my vehicle at night, because it could start an electrical fire. This is caused by heat from the lights.
- Electrical system · Exterior lighting · Service brakes
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving and activating the turn signals, the taillights were inoperable. Additionally, the contact stated while driving and depressing the brake pedal to come to a stop, the brake lights were significantly dimmed except for the…
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving and activating the turn signals, the taillights were inoperable. Additionally, the contact stated while driving and depressing the brake pedal to come to a stop, the brake lights were significantly dimmed except for the third brake light. The vehicle was taken to the dealer, where it was diagnosed with electrical failure. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 14V177000 (Exterior Lighting); however, the VIN was not included. The manufacturer was notified of the failure and informed the contact that they could not assist because the VIN was not included in the recall. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was unknown.
- Steering · Structure › Body · Suspension
The entire rear subframe of any W205 body model including but not limited to the C class from 2009-2014, CL class, SL, class ETC. suffers admittedly from MB USA, premature rust, deterioration etc. there is an active recall for these same models in Canada and all of Europe but not the USA. My garage…
The entire rear subframe of any W205 body model including but not limited to the C class from 2009-2014, CL class, SL, class ETC. suffers admittedly from MB USA, premature rust, deterioration etc. there is an active recall for these same models in Canada and all of Europe but not the USA. My garage kept 2009 C300 has suffered extensive rear end damage from a factory defect that Mercedes refuses to recognize in the Continental U.S. but will admit the same issues occurred in the EU and Canada. Keeler Mercedes, USA, of Colonie New York, stated they completed my subframe repair under the MB rear subframe extended warranty. The vehicle was driven home and inspected only to find out Keeler Mercedes of NY did NOT replace this crucial safety component under MB-USA extended warranty issued for this defect. This is pure negligence. When asked why the subframe wasn’t replaced as the work order stated it did, they stated “a mix up in paper work” I believe Mercedes-Benz USA and Keeler Mercedes of New York conspired together to push this massive safety defect aside and lie about completing the work in fear of the payment from warranty not being worth the labor hours required by the technicians. This oversight COULD have been a multi million dollar lawsuit if any injury was sustained after said repairs were done in belief the vehicle was safe to drive. Keeler Mercedes’ has also had this vehicle in their possession from June 14th 2024, to todays date, July 5th 2024 with no word on when repairs to subframe will be completed. Subframe replacement stated on MB website states it is an 8 hour labor job. We’re on day 18 now. MAJOR safety issue and shady dealing by dealership
- Air bags · Air bags › Srs malfunction warning lamp/light · Engine
The contact owns a 2009 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the "SRS System Requires Service" was displayed. The air bag and check engine warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the vapor…
The contact owns a 2009 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the "SRS System Requires Service" was displayed. The air bag and check engine warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the vapor canister shutoff valve but had not provided a diagnosis for the SRS system. The vehicle was repaired. The manufacturer was notified of the failure, and a case was opened. The failure mileage was 99,000.
- Suspension
After noticing brake fluid leaking I took my car to a local automotive shop and when he raised it to checkout the break line when he found the leak from the rust . he noticed a more serious problem that the subframe was rusted out on each side. He told me to contact Mercedes immediately because the car is unsafe to drive.
- Electrical system
Last week just before Thanksgiving my car of 134,000 miles wouldn't start. Had it towed to my mechanic only to find out like so many others that the Electronic Steering Module(ESL) is 1,500.00 defective. Yet with this being a common issue there is no recall. guess I'm going to a Toyota.
- Suspension
As I was driving from work, I noticed that when I started using the brakes I starting hearing a metal sound coming from the back, the day after I looked down and realized a whole part from the sub frame was completely broken and the part is corroded.
- Suspension · Unknown or other
The caption and case number is Sowa et al v. Mercedes-Benz USA, LLC et al., [XXX] MBUSA has extended the warranty on the rear subframe of several vehicles. The link to this in on your website: [XXX] One the last page of the PDF file on your website it states: When will customer letters be mailed…
The caption and case number is Sowa et al v. Mercedes-Benz USA, LLC et al., [XXX] MBUSA has extended the warranty on the rear subframe of several vehicles. The link to this in on your website: [XXX] One the last page of the PDF file on your website it states: When will customer letters be mailed for this warranty extension? The warranty extension customer notifications are scheduled for mailing on: March 10, 2023, and continue in waves through May 19. We have three cars in my family that are in this "extended warranty" at three different households. No letter was received at any of the three households regarding any of the three cars. If you look up the three cars Vin #'s, all three have no recalls on them and nothing relating to an extended warranty on a rear subframe. So, MBUSA, has brilliantly side stepped issuing a recall which would come up on a Vin $ search. They have not sent out the letters of notification. So, almost all owners will not be aware of the deadly impending time bomb they are driving. As these cars age further the ones that have yet to fail will fail and people will die. I called today, 10/24/2023 Reference # for the call [XXX] to let the NHTSA know the above and that if you allowed MBUSA to NOT issue a recall because they agreed to send letters of notification - well they did not do that and people are at risk. This seems like a loophole to me. No recall, we will extend the warranty and then not let anyone know much lower cost than recall and fixing. The NHTSA - should get the contact information for all the customers affected and hire a third party to send the notices and have MBUSA billed for that service. This would ensure people are notified. I was advised by the NHTSA staff on my call to file a claim with the BBB. That seems ridiculous. I will keep a copy of this filing; so, I can send it to the news channels to show how the NHTSA given due notice did nothing. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine and engine cooling · Exterior lighting › Turn signal
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, she became aware that the coolant level was low. The contact added coolant to the reservoir. The contact stated that the coolant reservoir burst open. The vehicle was towed to an independent…
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, she became aware that the coolant level was low. The contact added coolant to the reservoir. The contact stated that the coolant reservoir burst open. The vehicle was towed to an independent mechanic who replaced the coolant and hose. The vehicle was taken to the local dealer but was not diagnosed or repaired. The vehicle was repaired, but the failure recurred. Additionally, the indicator lights became inoperable. The check engine warning light was illuminated. The contact stated the failure was associated with NHTSA Campaign Number: 22V168000 (Exterior Lighting, Electronic Stability Control, Engine and Engine Cooling). The manufacturer was contacted, but no assistance was provided. The failure mileage was unknown.
- Suspension · Unknown or other
Was told by a mechanic that there is a safety recall for sub frames on Mercedes vehicles. After an inspection the mechanic noted that it was suggested to replace due to a recall on the c-class models. After looking up the VIN it suggested that a 2009 does not have a recall - same sub frame issue.
- Electronic stability control (esc) · Engine and engine cooling · Exterior lighting
The contact owns a 2009 Mercedes-Benz C300. The contact stated that the coolant warning light was frequently illuminated due to low coolant. The vehicle was taken to an independent mechanic where the engine hose and other engine parts were replaced. Despite the repair, the coolant light returned…
The contact owns a 2009 Mercedes-Benz C300. The contact stated that the coolant warning light was frequently illuminated due to low coolant. The vehicle was taken to an independent mechanic where the engine hose and other engine parts were replaced. Despite the repair, the coolant light returned soon after the initial repair. The contact then took the vehicle to a dealer where the failure was linked to NHTSA Campaign Number: 22V168000 (Exterior Lighting, Electronic Stability Control, Engine and Engine Cooling); however, the VIN was not included in the recall. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was unknown.
- Electronic stability control (esc) · Engine and engine cooling · Exterior lighting
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving approximately 65 MPH, the instrument cluster started flickering and the vehicle stalled. The contact stated that the power steering and brakes were operable. The contact pulled off the highway and shifted the vehicle into…
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving approximately 65 MPH, the instrument cluster started flickering and the vehicle stalled. The contact stated that the power steering and brakes were operable. The contact pulled off the highway and shifted the vehicle into park(P). The vehicle failed to restart and was towed to the dealer. The vehicle was not yet diagnosed or repaired. The manufacturer had been informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 22V168000 (Exterior Lighting, Electronic Stability Control, Engine and Engine Cooling) however, the VIN was not included. The failure mileage was approximately 119,000.
- Air bags · Electrical system · Suspension
i was driving in the highway 50 mph and i was braking and my car slipped in the other line of the highway and almost had and accident !!!! and cars switched off when driving almost had incident!!!! i saw that many people have the say problem like me about rusted component please do something because people are losing their lifes.
- Structure › Body
This car I have owned since brand new and I am the original owner. This car has never been used in winter despite I live in New York and always has been maintained in very good condition however, this car has developed noises from the rear when driven. I took the car to my trusted mechanic and he found out that the rear subframe has corrosion making it unsafe to drive.
- Electrical system · Exterior lighting
While driving and when parked the headlights flicker on and off. I have no headlights while driving at night, during adverse weather conditions and during dawn hours. I could crash into other drivers, or they could crash into me because they can’t see me. When a parking bulb blows it fuses and melts everything together causing the replacement of the entire headlight unit, this has happened twice.
- Structure › Frame and members
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving at various speeds, the vehicle would sway from side to side as an abnormal clonking noise would emit from the vehicle without warning. The vehicle was taken to an independent mechanic where they discovered that the…
The contact owns a 2009 Mercedes-Benz C300. The contact stated while driving at various speeds, the vehicle would sway from side to side as an abnormal clonking noise would emit from the vehicle without warning. The vehicle was taken to an independent mechanic where they discovered that the subframe had cracked due to severe corrosion. The dealer was contacted about the failure, and she was given an estimate for the repair. The manufacturer was also notified of the failure and the contact was given a case number. The vehicle had yet to be repaired. The failure mileage was 94,200.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Loss of rear lighting assembly
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish…
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ
- Loss of rear tail light functionality
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed…
ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10235996Additional information around the recent recall announcement affecting approximately 705,983 Mercedes-Benz passenger vehicles involving Takata driver-side airbags containing PSDl-5 type inflators
- 10235983Daimler AG (DAG) has decided that a supplier production error in the SRS control unit could lead to a failure of the SRS control unit. This malfunction of the SRS control unit would illuminate the SRS warning lamp and subsequently deactivate the SRS components. Additionally, in the event one specific electrical connection is interrupted, several SRS components could inadvertently deploy, increasing the risk for injury.
- 10235978Recall Campaign announcement for Takata driver airbags.
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
- 10205265Outside mirror fogged.
- 10205239"Anti-theft protection activated".
- 10205237The COMAND unit does not start or the display remains dark.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205225Headlamps fogged.
- 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
- 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
- 10181124Harsh engagement when changing gear range from P to D or R
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167560Fault message in display - Right rear turn signal light inoperative
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167552Engine does not start, or various fault messages in instrument cluster immediately after engine start and servo assistance is reduced. The following display messages may appear: - Red message "Power Steering Malfunction - See Operator's Manual" including acoustic warning - Red or yellow message "ESP / ABS Currently Unavailable - See Owner's Manual", sometimes with acoustic warning - White message about tire pressure monitor or run flat indicator: "Tire Pressure Loss Warning Defective" or "Tire Pressure Monitor Defective" In addition, the indicator lamps of the following systems may light up: - Brakes / ABS / ESP / ESP Off / engine diagnosis Furthermore: - The chassis CAN is partially or completely disrupted - Several control units (e.g. the electric power steering, ESP, engine etc.) cannot be interrogated or are not listed in the quick test - Various CAN communication errors from other control units may be logged (see list "Control unit / Fault code")
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
- 10167536Model X204 (GLK 250 BT) with AMG Styling Package 321. Model Year 2013 Install Tire Fit Kit, Replace Monroney Label
- 10167532A production fault means that the telematics DVD A 166 827 14 00 cannot be used. Because of this the previous telematics DVDs A 204 827 03 65 and A 204 827 10 65 must continue to be used for control unit programming. If required, these are still available for ordering. With XENTRY DVD 03/2014 a new telematics DVD with part number A 166 827 21 00 is being shipped. This telematics DVD replaces the previous telematics DVDs.
- 10167525Apple products (iPhone or iPod) are not charged via the serial USB interface of the COMAND Online control unit (A40/3) in the stowage compartment of the center console.
- 10167510The vehicle cannot be started The vehicle may start by itself shortly after the startup attempt with a delay, as the relay can be late closing. and/or The gear selection is displayed, but no gear is engaged. Gear selection is not possible. and/or Rear window wiper inoperative. and/or Various fault codes concerning disrupted communication paths are stored and/or the corresponding control units are not displayed in the quick test. Affected control units include the transmission control unit, electronic ignition lock, driver SAM, engine control unit, Lane Keeping Assist, Distronic.
Every Mercedes Benz C300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.