2017 Mercedes-Benz C 300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › C 300 › 2017
These records cover every 2017 Mercedes-Benz C 300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
15 recalls name the 2017 Mercedes-Benz C 300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2021 C300, 2017-2020 AMG C43, and AMG C63 vehicles. The front seat belts might not fully retract to their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Risk and remedy
Risk
If the seat belt does not fully retract, the occupant may find the operation of the seat belt inconvenient and not wear it, increasing the risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will check the retraction function of the front seat belts and adjust the damping foam within the B-pillars, as necessary, free of charge. The recall began February 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021020010.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC (Mercedes) is recalling certain 2017-2018 Mercedes-Benz C300 Cabriolet, C300 Coupe, AMG C43 Coupe, C300 4MATIC Cabriolet, C300 4MATIC Coupe, AMG C43 Cabriolet, AMG C63 Cabriolet, AMG C63 Coupe, AMG C63 S Cabriolet and AMG C63 S Coupe vehicles and 2018 Mercedes-Benz E400 Coupe, E400 Cabriolet, E400 4MATIC Cabriolet and E400 4MATIC…
Risk and remedy
Risk
If the seatback does not properly lock, in the event of a crash, the seatbacks may fold forward, increasing the risk of injury.
Remedy
Mercedes will notify owners, and dealers will inspect the locking of the seatback on the affected vehicles and replace the seatback lock, as necessary, free of charge. An interim owner letter was mailed on April 12, 2019 to notify owners. Owners will receive a second notification when the remedy is available. Owners may contact Mercedes-Benz customer service at 1-800-367-6372. MBUSA's number for this recall is 2019040007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 Mercedes Benz C300, 2017-2019 C300 Cabrio, C300 Coupe, C63 Cabrio, 2015 C63S AMG, 2018-2019 C300, C350e, C63 AMG, C63S AMG Cabrio, 2018 C63 AMG Cabrio, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, E300, E400 Cabrio, E400 Coupe, 2019 CLS450, E450 Cabrio, and E450 Coupe rear-wheel drive vehicles. A…
Risk and remedy
Risk
A car that cannot be properly steered has an increased risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the steering rack, free of charge. The recall began August 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019080012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2018 Mercedes C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63S AMG Cabriolet, and C63 AMG Cabriolet vehicles. Due to a bonding issue introduced in the production process, the rear beltline trim may separate from the vehicle.
Risk and remedy
Risk
If the beltline trim were to separate from the vehicle while driving, it could become a road hazard, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the rear beltline trim and replace the trim if necessary, free of charge. The recall began on September 21, 2018. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2018 C43 AMG 4Matic Coupe, C300 Coupe, C300 4Matic Coupe, C300 4Matic Cabriolet, C300 Cabriolet, C43 AMG 4Matic Cabriolet and C63S AMG Cabriolet, 2017 C63 AMG Cabriolet, C63S AMG Coupe and C63 AMG Coupe, 2018 E400 Coupe and E400 4Matic Coupe vehicles. The seatbacks of the front seats may not properly…
Risk and remedy
Risk
If the seatback does not properly lock, in the event of a crash, the seatbacks may fold forward, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the locking of the seatbacks, replacing the seatbacks lock, as necessary, free of charge. The recall is expected to begin May 25, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018040007.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2016-2017 C300 vehicles. The electrical contacts for the power steering electric motor may not have been properly welded, possibly resulting in a loss of electrical contact.
Risk and remedy
Risk
A loss of electrical contact will cause the electric power steering assist to deactivate, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the electric power steering rack, free of charge. The recall began June 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 C300, C300 4Matic, C300 Coupe, C300 Coupe 4Matic, C43 AMG, C43 AMG Coupe, C43 AMG Cabrio, C63 AMG, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, C63S Cabrio, GLC300, GLC300 4Matic, GLC43 AMG, S550, S550 4Matic, S550e, S600, S63 AMG 4Matic, S65, Mercedes-Maybach S550 4Matic, and Mercedes-Maybach S600…
Risk and remedy
Risk
If the front seat seatbelt pretensioners do not function properly, the seat occupants may not be adequately restrained in the event of a crash, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the front seat belts, free of charge. The recall began October 13, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450…
Risk and remedy
Risk
If the starting current limiter overheats, the surrounding components can melt, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will install an additional fuse in the electrical line to the starter, free of charge. The recall began August 31, 2017. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2017080002.
Owner complaints
216 complaints10 involved a crash3 involved a fire17 injuries
What owners report most
Latest complaints
- Unknown or other
The convertible roof gets stuck partially in open or closed position. It has to be forced closed. The vehicle is always garaged and the convertible was used very carefully but still has been troublesome from the beginning
- Engine
2017 Mercedes c300 the switchover valve in the diagnostic module of the evaporative emission control system is jammed open. This issue was called for recall for models 2018 or later, but 2017 was not part of it.
- Electrical system · Engine · Fuel system, gasoline
The contact owns a 2017 Mercedes-Benz C300. While driving at approximately 15 mph, the contact observed smoke emanating from under the hood. The vehicle was driven to her work location and parked. Upon exiting the vehicle and opening the hood, she observed orange flames coming from the engine…
The contact owns a 2017 Mercedes-Benz C300. While driving at approximately 15 mph, the contact observed smoke emanating from under the hood. The vehicle was driven to her work location and parked. Upon exiting the vehicle and opening the hood, she observed orange flames coming from the engine compartment. A parking attendant extinguished the fire, and a police and/or fire report was filed. The vehicle was towed to a dealer and diagnosed with a fuel line leak that caused the engine harness to come apart. The leaking fuel hose from the high-pressure fuel pump caused damage to the high-pressure pump, engine harness, vacuum transducer, and coolant feed line from the thermostat to the firewall. The following components needed replacement: high-pressure fuel pump, rubber fuel hose, engine harness, pressure transducer, and intake manifold. The vehicle was repaired. Five months later, the contact experienced another failure she believes was associated with the engine fire. While parked and attempting to start the vehicle, it did not start. The vehicle was towed to a dealer and diagnosed with a faulty starter that needed replacement. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 65,422.
- Fuel/propulsion system
strong evident fuel/ gas smell when driving and when the car is in park after driving.
- Engine
Check engine light for P052E which has been coming and going off for years now. Now the check engine light is there permanently. I spoke to Mercedes Benz customer service and requested for them to fix the problem now that the light is on permanently but they refuse to fix it because the car has…
Check engine light for P052E which has been coming and going off for years now. Now the check engine light is there permanently. I spoke to Mercedes Benz customer service and requested for them to fix the problem now that the light is on permanently but they refuse to fix it because the car has 222,000 miles on it. This should be a recall from the manufacturer not an extended warranty coverage. The Mercedes dealer in Valencia California told me they now only do a software update and put a plug cap on the sensor and want to charge me $850 even though this should be a recall
- Fuel/propulsion system
UNKNOWN it was just one day I started my car and turned the A/C on and I started getting this strong gasoline smell. I went on like a saw there is a recall for this problem for the M274 engines.
- Structure › Body
While driving home from work, without any warning or blunt force the sunroof exploded and shattered glass was everywhere
- Seat belts
any action on Case 11699173 ?
- Seat belts
Case already called in 11699173 - Stuck Seatbelt in B Pillar of 2017 Mercedes Benz 2 door hard top coupe. Seat belt will not come out of A pillar rendering seatbelt totally inoperable This VIN comes up negative under recall 21V03200 Case filed with MBUSA 18991593 still unresolved. Dealership is…
Case already called in 11699173 - Stuck Seatbelt in B Pillar of 2017 Mercedes Benz 2 door hard top coupe. Seat belt will not come out of A pillar rendering seatbelt totally inoperable This VIN comes up negative under recall 21V03200 Case filed with MBUSA 18991593 still unresolved. Dealership is claiming a $2,200 Seatbelt Assembly is needed. now warning lights. The seatbelt was " lazy " and didn't smoothly retract prior to this incident when parked, door closed, the belt retracted with a loud motorized noise and now will not retract at all from A Pillar - Please follow up with on this Case # already called in over a week ago
- Seat belts
The contact owns a 2017 Mercedes-Benz C300. The contact stated that upon arriving at his destination and exiting the vehicle, the driver’s side seat belt retracted and became stuck in the retracted position. As a result, the contact was unable to use the driver's side seat belt. No warning lights…
The contact owns a 2017 Mercedes-Benz C300. The contact stated that upon arriving at his destination and exiting the vehicle, the driver’s side seat belt retracted and became stuck in the retracted position. As a result, the contact was unable to use the driver's side seat belt. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the seat belt assembly. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 21V032000 (Seat Belts), but the VIN was not included. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 67,000.
- Fuel/propulsion system
Cabin smells heavily like fuel and has a check engine light possibly a fuel leak
- Structure
The contact owns a 2017 Mercedes-Benz C300. The contact stated that while driving 65 MPH on the highway, the contact heard a popping sound coming from an unknown part of the vehicle. The contact pulled over to the side of the road, exited the vehicle, and became aware that the roof panel had…
The contact owns a 2017 Mercedes-Benz C300. The contact stated that while driving 65 MPH on the highway, the contact heard a popping sound coming from an unknown part of the vehicle. The contact pulled over to the side of the road, exited the vehicle, and became aware that the roof panel had shuddered. The contact stated there was no glass in the vehicle. No injuries were sustained. The contact stated that the failure had occurred on two occasions. The vehicle was not taken to an independent mechanic or the dealer to be diagnosed. The vehicle was taken to the dealer by the previous owner to be repaired under NHTSA Campaign Number: 21V197000 (STRUCTURE); however, the recall repair failed to prevent the failure. The manufacturer was notified of the failure and informed the contact that there was no recall related to the failure. The manufacturer offered the contact a trade for the vehicle. The failure mileage was 105,000.
- Electrical system · Engine · Structure › Body
I am reporting a serious vehicle safety hazard caused by improper and unsafe repair work performed by USA Platinum Motor, located at 1221 California Lane #126B, Arlington, TX. I brought my 2017 Mercedes-Benz C300 in for a cold start rattle with no warning lights or prior issues. The shop diagnosed…
I am reporting a serious vehicle safety hazard caused by improper and unsafe repair work performed by USA Platinum Motor, located at 1221 California Lane #126B, Arlington, TX. I brought my 2017 Mercedes-Benz C300 in for a cold start rattle with no warning lights or prior issues. The shop diagnosed a loose timing chain and I authorized the repair. After the repairs, the vehicle was returned with critical safety defects, including a loose fuel pump, unsecured fuel line, missing bolts, and improperly reassembled engine components. Shortly after pickup, the car experienced loss of acceleration on the interstate, a strong odor of fuel, and a sudden loss of power, creating a dangerous and life-threatening situation. The vehicle had to be towed back to the shop. The manager, who is not a certified mechanic, admitted he personally “fixed” the issue by tightening the fuel pump himself. A Mercedes-Benz diagnostic inspection later confirmed multiple severe assembly errors, including missing fasteners, unsecured oil cooler, disconnected vent lines, and other safety-related defects in the fuel and cooling systems. These unsafe and negligent repairs created an extreme fire hazard, engine instability, and risk of sudden failure while driving. I am requesting a formal NHTSA investigation into this matter to ensure vehicle safety compliance and to prevent similar incidents affecting other consumers.
- Structure › Body
This is the same as recall for NHTSA ID: 21V-197. The panel flew off my 2017 Mercedes C300 W205. My vin number is not included in the recall. This is a safety issue and will need to be replaced.
- Structure › Body
Sunroof detachment Sunroof fell off while driving
- Communication › Auto crash notification · Electrical system › Software
See attached document for complaint.
- Unknown or other
Sunroof front trim for mercedes-benz glc300 IS all scratched but mercedes benz says it IS not covered by them.
- Structure
The contact owns a 2017 Mercedes-Benz C300. The contact stated that while driving at 60 MPH, the contact became aware that an unknown part had detached from the vehicle. The contact stated that after stopping to refuel the vehicle, it was discovered that the roof panel was missing. The vehicle was…
The contact owns a 2017 Mercedes-Benz C300. The contact stated that while driving at 60 MPH, the contact became aware that an unknown part had detached from the vehicle. The contact stated that after stopping to refuel the vehicle, it was discovered that the roof panel was missing. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact related the failure to NHTSA Campaign Number: 23V854000 (Structure); however, the VIN was not included in the recall. The manufacturer was not made aware of the failure. The failure mileage was approximately 129,000.
- Structure › Body · Unknown or other
The sunroof exploded spontaneously while driving to a destination. When the incident happened, I was stopped at a red light. I panicked as it sounded like gunshots hitting my car. I pulled over to the nearest safest destination to inspect the car. This put the safety of myself at risk and others at…
The sunroof exploded spontaneously while driving to a destination. When the incident happened, I was stopped at a red light. I panicked as it sounded like gunshots hitting my car. I pulled over to the nearest safest destination to inspect the car. This put the safety of myself at risk and others at risk who were driving along the sides and/or behind me. This incident was confirmed by a dealer, as I went to Mercedes Benz Sugar Land on the following day of the incident and was quoted around $3,700 to have it repaired. The vehicle not been inspected by police and/or insurance. There were no warning signs that this could have happened besides the fact that Mercedes Benz USA is currently under an active lawsuit for this happening to several other drivers. I do believe that this is a manufacturing defect affecting safety, as similar incidents involving Mercedes-Benz panoramic sunroofs, which may indicate a wider defect trend.
- Air bags · Suspension · Unknown or other
In October 2024, the rear subframe was replaced due to rust perforation in the area of the suspension arm mounting bracket. I had no warning. The car was in for routine service at Mercedes Benz of New London. It had rusted from the inside out and was considered unsafe to drive by the Mercedes…
In October 2024, the rear subframe was replaced due to rust perforation in the area of the suspension arm mounting bracket. I had no warning. The car was in for routine service at Mercedes Benz of New London. It had rusted from the inside out and was considered unsafe to drive by the Mercedes service advisor. I could have had a serious accident! I had no choice but to replace the subframe as it is my only vehicle. Shockingly I learned many others have had this issue with various Mercedes models/years and that Mercedes Benz knows of this serious safety problem and there is a class action lawsuit pending but subframe replacement is not covered under warranty by Mercedes Benz, so the cost was mine to bear.
- Unknown or other
My car caught on fire due to AC malfunction
- Seat belts
The contact owns a 2017 Mercedes-Benz C300. The contact stated that both the front driver’s side seat belt and front passenger's side seat belt had failed to retract as needed. There was no warning light illuminated. Additionally, the contact stated that the seat belts buckles would unintendedly…
The contact owns a 2017 Mercedes-Benz C300. The contact stated that both the front driver’s side seat belt and front passenger's side seat belt had failed to retract as needed. There was no warning light illuminated. Additionally, the contact stated that the seat belts buckles would unintendedly lodge under the seats. The vehicle was taken to the local dealer, but was not diagnosed or repaired. The contact related the failure to NHTSA Campaign Number: 21V032000(Seat Belts); however, the VIN was not included. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was unknown.
- Electrical system · Unknown or other
The sunroof is very glitchy and this is common in all Benz I have had a few different Benz and they all eventually have this same issue with their panoramic sunroof. Sometimes it opens half way life one side is up and the other side is closed and other times it will open fully but not close and…
The sunroof is very glitchy and this is common in all Benz I have had a few different Benz and they all eventually have this same issue with their panoramic sunroof. Sometimes it opens half way life one side is up and the other side is closed and other times it will open fully but not close and other times it won’t open at all. This is a common problem that many Benz owners have stated this in the Benz forums all over. This is a safety issue due to unexpected weather conditions if it rains and it’s stuck inside gets damage and owners get wet which is also a distraction and may cause accidents. Please investigate this issue thoroughly. Their sunroofs should be recalled and extended warranties placed on them automatically by Mercedes Benz due to this being a very common issue in all model’s panorama sunroofs particularly C300s year 2017 thank you for looking into this matter.
- Steering · Suspension
unknown
- Electrical system · Engine
ESP control unit software Recall 2016090002 Recall 2017110002 Recall 2020080016 And my car shows there’s cero recall active but is giving me problem showing code: U0121 u1110 U0122 B227d U0423 B227d
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005276Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2018 C300 | Model year 2016-2018 GLC300 and E300 | ALL model year SLK/SLC300 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2018 C300 and 2016-2018 GLC300 and E300 vehicles. Model year 2015-2017 C300 | Model year 2019 GLC300 and E300 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required.
- 11000623Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2015-2018 (non-hybrid), and ALL model year 172 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for hybrid and model year 2015-2018 vehicles. Model year 2019 (Except model 172 and hybrid variants) Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 10253722Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10246281Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10243308Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10241531In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 0101D Solenoid valve, crankcase ventilation system Part(s): A 274 090 5600 80 Intake Line Assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilationvalve.) Where applicable, an ECU software update will be provided for certain vehicle variants. Time Allowed: Intake Line Assembly : 5 hours 40 minutes Software Update: 1 hour Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.
- 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
- 10233783Complaint Loads induced at the steering wheel through pushing and pulling actions may cause creaking and cracking noises in the mechanical steering column. Cause Insufficient grease lubrication in the clamping area of the mechanical steering column. Remedy Grease the clamping area.
- 10231031Staining on door trim strips and top and bottom trim elements on rear side windows. Cause Damage to protective coating of door beltline trim strips, door upper trim strips and side window trim element. Remedy 1. Check if the problem cannot be rectified by polishing the trim bars with the polishing paste. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.
- 10217162Complaint Customer may have one or more of the following complaints: Vehicle location is shown incorrectly in the Navigation Display Navigation destination search is not possible Street names are not shown in Navigation display Apple Carplay is inoperable Cause Improper installation of navigation map data Remedy Follow these steps to delete and re-install map data: Re-format an empty USB drive to NTFS (do not use quick formatting option) Unzip the attached map data deletion file directly to the USB drive. Do not add a folder, only the root files should be shown on the USB drive Generate a pin for the Navigation Delete Database in Vedoc (see attached screenshot) Plug USB drive with map data delete file into the vehicle's USB port and follow instructions in the COMAND Display to delete the installed map data Once the originally installed map data is deleted, then install the newest available map data in Download Manager
- 10217157Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
- 10217154Complaint Thumping noise on rear axle shock absorber on rough road. Cause Until now the rear axle shock absorber support bushing was only available together with the rear axle shock absorber as a replacement part. In future, the rear axle shock absorber support bushing will be available individually as a replacement part to avoid any unnecessary shock absorber noise. Remedy For noise problems on the rear axle shock absorbers, please always make a noise diagnosis, for example using Chassis Ear to localize any sources of noise on shock absorbers or support bushings. If the noise originates from the upper part of the shock absorbers, it is enough to replace the support bushings. Otherwise the complete shock absorber including support bushing have to be replaced. The modified support bushings must be replaced in pairs the first time so that any mixed installation of old and new is reliably ruled out.
- 10215212Complaint Customer may have one or more of the following complaints: Vehicle location is shown incorrectly in the Navigation Display Navigation destination search is not possible Street names are not shown in Navigation display Apple Carplay is inoperable Cause Improper installation of navigation map data Remedy Follow these steps to delete and re-install map data: Re-format an empty USB drive to NTFS (do not use quick formatting option) Unzip the attached map data deletion file directly to the USB drive. Do not add a folder, only the root files should be shown on the USB drive Generate a pin for the Navigation Delete Database in Vedoc (see attached screenshot) Plug USB drive with map data delete file into the vehicle's USB port and follow instructions in the COMAND Display to delete the installed map data Once the originally installed map data is deleted, then install the newest available map data in Download Manager
- 10209877Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy Follow guided tests as described.
- 10209874Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain MY 2015-2018 C-Class and GLC-Class (205 and 253 platform) vehicles, the software for the powertrain control unit may not correspond to the current production specifications. It is possible that the next maintenance interval is displayed to the user as a negative distance reading in the instrument cluster. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the powertrain control unit software.
Every Mercedes-Benz C 300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.