2016 Mercedes-Benz C300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › C300 › 2016
These records cover every 2016 Mercedes-Benz C300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
13 recalls name the 2016 Mercedes-Benz C300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 AMG G63, C300, E300, G550, AMG GT63, AMG GT53, 2019-2020 A220, GLA250, GLC300, 2016 C300, 2020 AMG A35, AMG C43, AMG C63, CLA250, E350, E450, GLB250, GLE450, GLS450, GLS580, S560, and SL550 vehicles equipped with a gasoline engine. During the manufacturing process, particles may have been trapped…
Risk and remedy
Risk
A fuel leak in the presence of an ignition source, such as hot engine or exhaust components, can increase the risk of a fire.
Remedy
Dealers will replace the fuel rail and fuel injectors, free of charge. Owner notification letters were mailed April 22, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for the recall is 2022030003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 Mercedes Benz C300, 2017-2019 C300 Cabrio, C300 Coupe, C63 Cabrio, 2015 C63S AMG, 2018-2019 C300, C350e, C63 AMG, C63S AMG Cabrio, 2018 C63 AMG Cabrio, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, E300, E400 Cabrio, E400 Coupe, 2019 CLS450, E450 Cabrio, and E450 Coupe rear-wheel drive vehicles. A…
Risk and remedy
Risk
A car that cannot be properly steered has an increased risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the steering rack, free of charge. The recall began August 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019080012.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2016-2017 C300 vehicles. The electrical contacts for the power steering electric motor may not have been properly welded, possibly resulting in a loss of electrical contact.
Risk and remedy
Risk
A loss of electrical contact will cause the electric power steering assist to deactivate, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the electric power steering rack, free of charge. The recall began June 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…
Risk and remedy
Risk
If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450…
Risk and remedy
Risk
If the starting current limiter overheats, the surrounding components can melt, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will install an additional fuse in the electrical line to the starter, free of charge. The recall began August 31, 2017. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2017080002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 GLC 300 SUV, GLC 300 4Matic SUV, C300 Sedan and C300 4Matic vehicles manufactured February 8, 2016, to May 18, 2016. The affected vehicles may be equipped with an Electronic Stability Program (ESP) control unit that may have been damaged before being installed.
Risk and remedy
Risk
A damaged ESP control unit may inadvertently activate the stability control altering the vehicle's path. Additionally, the electronic parking brake may not function. Either condition may increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the ESP Hydraulic control units, free of charge. The recall is expected to begin in October 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 C300 4Matic vehicles manufactured November 4, 2015, to March 1, 2016. In the affected vehicles, the electric power steering assist system may shutdown due to a software error.
Risk and remedy
Risk
If the vehicle experiences a loss of power steering assist, extra steering effort will be required at lower speeds, increasing the risk of a vehicle crash.
Remedy
MBUSA will notify owners, and dealers will update the software for the electric power steering control unit, free of charge. The recall began January 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 C300 vehicles manufactured December 11, 2015, to December 23, 2015, C300 4Matic vehicles manufactured December 12, 2015, to December 29, 2015, and C450 AMG 4Matic vehicles manufactured December 12, 2015, to December 22, 2015. The affected vehicles may be equipped with a panoramic sunroof…
Risk and remedy
Risk
If the panoramic glass detaches during vehicle operation, it can increase the risk of injury or crash.
Remedy
MBUSA will notify owners, and dealers will inspect the bonding of the rear sunroof glass panel, replacing it as necessary, free of charge. The recall began on April 12, 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
291 complaints7 involved a crash5 involved a fire8 injuries
What owners report most
Latest complaints
- Engine · Fuel/propulsion system
Hi, in the Fall of 2025 my 2016 Mercedes Benz C300 4 Matic, started giving off smelly fumes while my car was idling/ warming up. I registered a complaint with the Corporate Mercedes Benz Office USA, LLC in April 2026 @ 800-367-6372, after the dealership would not correct the issue free of charge.…
Hi, in the Fall of 2025 my 2016 Mercedes Benz C300 4 Matic, started giving off smelly fumes while my car was idling/ warming up. I registered a complaint with the Corporate Mercedes Benz Office USA, LLC in April 2026 @ 800-367-6372, after the dealership would not correct the issue free of charge. 1. Hose Clamp Replacement problems. 2. The raw fuel leakage produces strong gasoline odors inside the cabin- via the air filter, risk of car stalling and the smell could be leathal. 3. The problem was confirmed in a lawsuit. 4. The dealership would not repair the issue. 5. There were no warning lamps or messages on the dash board, the only essential issue were the smells, fumes, odors and lawsuit.
- Suspension
Vehicle: 2016 Mercedes-Benz C300, VIN [XXX], approximately 52014 miles. Purchased Certified Pre-Owned in 2017. All maintenance performed at authorized Mercedes-Benz dealerships. On XXX, during a routine B-Service at Mercedes-Benz of Easton ([XXX]), the technician found that the rear subframe (rear…
Vehicle: 2016 Mercedes-Benz C300, VIN [XXX], approximately 52014 miles. Purchased Certified Pre-Owned in 2017. All maintenance performed at authorized Mercedes-Benz dealerships. On XXX, during a routine B-Service at Mercedes-Benz of Easton ([XXX]), the technician found that the rear subframe (rear axle carrier) was rusted and perforated. The corroded area is located directly above the rear control arm. The technician stated on a recorded inspection video that the corrosion would continue to spread around that area until the control arm disconnects, and described it as a safety hazard. He recommended replacement of the part. Photos and video (technician shared video link - [XXX]) were taken during the inspection and are available. I was not notified of any corrosion in this area during previous dealer services, and the vehicle showed no symptoms that I noticed before this inspection. I am concerned that a structural suspension mounting component has corroded through on a vehicle of this age, and that if the control arm separates from the subframe, it could cause loss of control. I am reporting this so that NHTSA can determine whether it is a wider problem on this model. No crash, injury, or fire has occurred. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Structure › Body
Rear sub frame has rusted through and according to repair shop cannot be safely driven until repaired. Mercedes has granted extended warranty for sub frame rust through for the C300 up to model year 2015 so this is a known problem. My car is a 2016 and Mercedes will not offer the extended warranty.
- Suspension
Failed state safety inspection due to a severely corroded and rotted rear subframe, creating an immediate driving hazard.
- Structure
The contact owns a 2016 Mercedes-Benz C 300. The contact stated that while performing maintenance on the vehicle with the dealer, it was discovered that the rear subframe was severely rusted and perforated. The contact associated the failure with Technical Service Bulletin: MC-10232321-0001…
The contact owns a 2016 Mercedes-Benz C 300. The contact stated that while performing maintenance on the vehicle with the dealer, it was discovered that the rear subframe was severely rusted and perforated. The contact associated the failure with Technical Service Bulletin: MC-10232321-0001; extended warranty, but vehicle was not included. The manufacturer was contacted by phone and made aware of the failure. The failure mileage was approximately 84,616.
- Unknown or other
Vehicle has prematurely rusted subframe. It is a know manufacturer defect, for which the manufacturer is covering repair cost for owners of the preceding model, but refuses to acknowledge responsibility on this model. (W204 model covered — W205 Mercedes (only offered $500.00 on a repair they value at over $6,000.00.))
- Engine
NHTSA Safety Complaint – 2016 Mercedes-Benz C300 Vehicle: 2016 Mercedes-Benz C300 | Mileage: 74,662 miles What Happened I’m filing this complaint because my 2016 Mercedes-Benz C300 suffered a sudden, complete engine failure at 74,662 miles, and I believe it’s a safety risk that deserves…
NHTSA Safety Complaint – 2016 Mercedes-Benz C300 Vehicle: 2016 Mercedes-Benz C300 | Mileage: 74,662 miles What Happened I’m filing this complaint because my 2016 Mercedes-Benz C300 suffered a sudden, complete engine failure at 74,662 miles, and I believe it’s a safety risk that deserves investigation. I’ve owned this car since 2016 and followed every recommended service interval. All available warranties were purchased and maintained. The car showed absolutely no signs of trouble before this happened. Last week before filing, I was driving normally when the check engine light came on without any prior warning — no oil pressure light, no temperature alert, nothing else. Within minutes, the engine shut off completely. The car rolled to a stop and I noticed oil leaking from the front of the engine. It was towed to an authorized Mercedes-Benz dealership, where they confirmed the engine suffered a catastrophic internal failure and needs to be fully replaced. Why This Is a Safety Concern No advance warning. The check engine light appeared only minutes before the engine died. That’s not enough time to safely exit a highway or busy road. A sudden total engine failure at speed affects steering, braking assist, and reaction time — it could easily cause a serious accident. Engine failure at 74,662 miles is not normal. A complete engine failure on a well-maintained luxury vehicle at under 75,000 miles strongly suggests a manufacturing defect or design flaw, possibly affecting other vehicles of the same model year. Oil leak at engine front. The leak observed at failure likely points to a specific component or seal failure. If this is a design weakness, other 2016 C300 owners may be at risk without knowing it. What I’m Requesting 1.Open an investigation into the 2016 Mercedes-Benz C300 for sudden engine failure and inadequate warning systems. 2.Determine whether other owners have reported similar incidents. 3.Evaluate whether a safety recall is warranted.
- Electrical system · Fuel/propulsion system · Unknown or other
I’ve been driving my car since September when it was purchased I just got it from dealership 4/9/26 spent over $1100 and have been working like regular full time schedule, I wake up today 4/27/26 trying to work and car is stalling. Not sure what’s going on with these mechanics and technicians. I…
I’ve been driving my car since September when it was purchased I just got it from dealership 4/9/26 spent over $1100 and have been working like regular full time schedule, I wake up today 4/27/26 trying to work and car is stalling. Not sure what’s going on with these mechanics and technicians. I pay to dollar to ensure my family safety on the road here I am stuck without support due to my circumstances. Also, my car just idles the shuts off doesn’t turn mall the way on, magically a check engine light flashed then car just immediately stalled and won’t turn back over all the way.
- Structure › Body · Unknown or other
Panoramic sunroof fails to open/ close evenly due to binding issue and plastic track failure. One side binds while the other moves, causing glass to tilt and jam. Risk of dangerous injury including glass shattering, sudden detachment, distraction while driving, and water intrusion affecting airbags/electronics.
- Electrical system · Engine · Power train
My C300 MBZ, 2016 is experiencing the same symptoms as indicated in a recall, but my vehicle is not included in that recall. Camshaft: GENERAL REPAIR A cam is a rotating or sliding piece in a mechanical linkage used especially in transforming rotary motion into linear motion or vice versa. Cams act…
My C300 MBZ, 2016 is experiencing the same symptoms as indicated in a recall, but my vehicle is not included in that recall. Camshaft: GENERAL REPAIR A cam is a rotating or sliding piece in a mechanical linkage used especially in transforming rotary motion into linear motion or vice versa. Cams act as a vital component to your automobile's engine. A camshaft is a shaft to which a cam is fastened or of which a cam forms an integral part. Camshafts provide power to the cams which are vital for basic engine operation. The cost of fixing this approximately $10,000 per Mercerdes dealer and estimate from Keyes Mercerdes. The Brief: Mercedes-Benz issued a recall for some model cars tied to a faulty drive shaft.T he problem not only can cause vehicles to lose power but may elevate crash risk, according to the National Traffic Safety Administration. Owners of the affected vehicles can take them to their local dealership to receive free repairs, however per MBZ corporate 2016 C300 not included? Mercedes-Benz is recalling 24,092 cars connected to a drive shaft universal joint that may break, resulting in a sudden loss of drive power.
- Power train · Suspension
I am reporting a structural failure of the rear subframe (axle carrier) on my 2016 Mercedes-Benz C300 (W205). The component is exhibiting significant internal-to-external corrosion (perforation), specifically at the suspension mounting points. Safety Impact: The vehicle is currently exhibiting…
I am reporting a structural failure of the rear subframe (axle carrier) on my 2016 Mercedes-Benz C300 (W205). The component is exhibiting significant internal-to-external corrosion (perforation), specifically at the suspension mounting points. Safety Impact: The vehicle is currently exhibiting unstable handling and a 'skittish' 'swerving' sensation causing the car to 'fishtail' under braking during normal braking and at highway speeds, indicating a compromise in the structural integrity of the rear axle. This poses an immediate risk of a 'loss of directional control' should the suspension components fully detach from the corroded subframe. The Structural Integrity, Loss of Directional Control, Sudden Suspension Failure, and causes extremely dangerous Safety Hazard for my family and other on the road. The corrosion has compromised the mounting points of the rear suspension, creating a risk that the axle will detach while the vehicle is in motion, leading to a catastrophic loss of control. Context: Mercedes-Benz has acknowledged this defect in previous years (2008-2015) via a 20-year extended warranty and in Service Information S135.00-P-0009A. However, they have failed to include the 2016 W205 in the safety remedy despite identical failure modes and documented safety hazards. Currently, as of April 2026, a 2024/2025 federal court ruling [XXX] v. Mercedes-Benz) allowed a class-action lawsuit to proceed specifically covering 2010–2022 models—including the2016 C300 W205—alleging the exact same manufacturing defect. A thorough inspection of the undercarriage of the vehicle shows severe corrosion to the subframe as well as a cracked hub along the drive-train shaft and differential. I have submitted photos along with this Vehicle Complaint From to document the corrosion of the subframe and other defects associated with the devices and systems that transmit power from the engine or propulsion device to the wheels such as the cracks in hubs, shafts, differentials. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORM
- Unknown or other
A lot of times when I park even on flat surfaces my parking brake engages and It’s hell being able to leave because I have to turn the car off open the door close door start the again put in drive while my foot is on the brake and pull and push the parking brake button 4 times. Then I’m able to drive. This has been happening more frequently and there is an open recall for the parking brakes calLED ESP RECALL
- Unknown or other
Spontaneous explosion of sunroof while car is in motion on the expressway 83 and could have caused an accident while my daughter was driving
- Structure
The contact owns a 2016 Mercedes-Benz C300. The contact stated that while driving approximately 20 MPH and turning the steering wheel to the right or the left, there was an abnormal clicking sound coming from the rear of the vehicle. There was no warning light illuminated. The contact had taken the…
The contact owns a 2016 Mercedes-Benz C300. The contact stated that while driving approximately 20 MPH and turning the steering wheel to the right or the left, there was an abnormal clicking sound coming from the rear of the vehicle. There was no warning light illuminated. The contact had taken the vehicle to a local dealer where it was diagnosed and determined that the rear sub frame of the vehicle had severe corrosion and needed to be replaced. The contact was advised by a service technician that there had been a recall for corrosion failures, but the year and the model were not included. The vehicle was not repaired. The manufacturer was informed of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 130,000.
- Fuel/propulsion system
Strong fuel smell in cabin Can maybe cause a fire
- Engine · Fuel/propulsion system
fuel lines/ clamps defective causing a fuel leak. vehicle could catch on fire and fumes are extremely strong inside the cabin. issue confirmed by Mercedes dealer, mentioned there is an extended warranty up to 120,000 miles. rejected mine because i was at 120,300 miles. had to pay out of pocket. no…
fuel lines/ clamps defective causing a fuel leak. vehicle could catch on fire and fumes are extremely strong inside the cabin. issue confirmed by Mercedes dealer, mentioned there is an extended warranty up to 120,000 miles. rejected mine because i was at 120,300 miles. had to pay out of pocket. no warning lights or anything just the really strong smell of fuel and fuel range dropping. this is a very common issue thats known and should be a recall.
- Fuel system, gasoline
The contact owns a 2016 Mercedes-Benz C300. The contact stated that whenever the fuel tank was full, there was a fuel-burning odor coming from the engine and entered the vehicle through the A/C vents. In addition, when the vehicle was cold, the odor was entering the vehicle through the A/C vents.…
The contact owns a 2016 Mercedes-Benz C300. The contact stated that whenever the fuel tank was full, there was a fuel-burning odor coming from the engine and entered the vehicle through the A/C vents. In addition, when the vehicle was cold, the odor was entering the vehicle through the A/C vents. No warning lights were illuminated. The vehicle was taken to a collision center specializing in foreign vehicles, where it was diagnosed that the fuel rail and injectors had a fuel leak. The vehicle was not repaired. The contact stated that the failure persisted. Upon further investigation, the contact related the failure to NHTSA Campaign Number: 21V961000 (FUEL SYSTEM, GASOLINE). However, the VIN was not included. The contact stated that his mother owned the vehicle in the past and gave the vehicle to the contact two years ago. The contact's mother remembered receiving a recall letter; however, the contact's mother was unsure if the vehicle had been repaired in the past. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 60,000.
- Steering
I am writing to formally report the premature failure and subsequent replacement of the electronic rack and pinion on my 2016 Mercedes-Benz C300 4Matic sedan. This repair was performed at Sears Imported Autos on 4/19/2024, at a cost of $5,840.14. Invoice number at Sears Imported Autos is XXX. My…
I am writing to formally report the premature failure and subsequent replacement of the electronic rack and pinion on my 2016 Mercedes-Benz C300 4Matic sedan. This repair was performed at Sears Imported Autos on 4/19/2024, at a cost of $5,840.14. Invoice number at Sears Imported Autos is XXX. My vehicle, VIN [XXX] , had only 74,427 miles at the time of the failure. The failure of a critical steering component at such a low mileage is highly unusual and, I believe, directly attributable to a latent manufacturing defect. I have recently become aware of a prior recall (NHTSA Campaign Number 18V850000) concerning the electronic power steering rack on these EXACT vehicles. While I acknowledge that my vehicle VIN was not included in the official scope of the previous NHTSA recall, the nature and timing of my component's failure strongly mirror the documented issues of MY power steering failure. Mercedes-Benz USA Customer Care Center just informed me that my VIN does NOT qualify for the recall, but they did NOT say the failure on my car was a different part. The fact that the very same exact part failed so prematurely, a component that is expected to last for the lifetime of the vehicle under normal conditions, points to a systemic quality control issue beyond the scope of the original recall. The recall should be expanded to include my VIN and likely a few others. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine
Vehicle developed OBD-II code P052E related to crankcase ventilation/PCV system malfunction. Issue causes improper crankcase pressure, rough idle, oil vapor smells, and check engine light. Independent research shows this is a common failure on 2015–2017 Mercedes C300 models. Repair requires replacement of crankcase vent/PCV assembly. This appears to be a premature emissions system failure.
- Fuel/propulsion system
An independent service center diagnosed my car as having a fuel leak stemming from the fuel rail and fuel injectors. This is a fire hazard due to a gas leak. There is a gas smell in the interior cabin that I noticed approximately one month ago. I believe this pertains to NHTSA ID #21V961, and I would like NHTSA to consider including my VIN in this recall.
- Fuel/propulsion system · Unknown or other
My 2016 Mercedes Benz C300 started giving off funky fumes last year in 2024, now the fumes have turned into the smell of gas in 2025. Everytime that I call the dealership on Rockside Rd./ Broadway, located in Bedford Ohio, they give me an excuse as to why it's not their responsibility to correct the issue. What can I do?
- Engine
CHECK ENGINE LIGHT appeared on dash at approximately 72k miles. Had code read and diagnosed by certified mechanic and he had an active code P06DA00(this code signifies an electrical fault, open circuit, or high resistance in the circuit for the oil pump control valve on vehicles with two stage oil…
CHECK ENGINE LIGHT appeared on dash at approximately 72k miles. Had code read and diagnosed by certified mechanic and he had an active code P06DA00(this code signifies an electrical fault, open circuit, or high resistance in the circuit for the oil pump control valve on vehicles with two stage oil pump, which can lead to incorrect oil pressure, which can cause engine damage if not addressed). Vehicle was taken to Harriman Mercedes in New York. They did not acknowledge an active code but wanted to diagnose and repair a stored code for a small evap leak, which was rectified with a new gas cap. After prying about the P06DA00 code, they finally admitted it did have a stored code but to ignore it because it had something to do with domestic and foreign car engine computers issues. How do you ignore an active code with a potentially serious engine issue and told to ignore it. I know for a fact that this is a common problem with these 2.0L engines in these cars for many years.
- Fuel/propulsion system
It's ridiculous I took my car to the dealer (mercedes-benz of novi, mi) yesterday 2016 mercedes C300 4matic for extended warranty on low pressure fuel hose as the car cabin smells like gas fumes to the point where it got me dizzy and nauseous and threw me in bed for a day. When I arrived there I…
It's ridiculous I took my car to the dealer (mercedes-benz of novi, mi) yesterday 2016 mercedes C300 4matic for extended warranty on low pressure fuel hose as the car cabin smells like gas fumes to the point where it got me dizzy and nauseous and threw me in bed for a day. When I arrived there I was told yeah this IS common on these cars and warranty will take care of it. Got a call later saying it will not be covered as the 10 year extended warranty surpassed my car as my car production date IS 09/15, I was like please its only a couple month after and its a fire hazardous and health matter they were like no, now my car IS there and I have to pay them $850 to change an issue that was supposed to be taken care from the beginning from the manufacturer.
- Fuel system, gasoline
The contact owns a 2016 Mercedes-Benz C300. The contact stated that there was a gasoline odor inside and outside the vehicle on several occasions, while driving at various speeds and while parked. The contact stated that the vehicle failed to accelerate as needed. The contact stated that there was…
The contact owns a 2016 Mercedes-Benz C300. The contact stated that there was a gasoline odor inside and outside the vehicle on several occasions, while driving at various speeds and while parked. The contact stated that the vehicle failed to accelerate as needed. The contact stated that there was no warning light illuminated, the fuel consumption increased, with the fuel gauge lowered more quickly. The vehicle was taken to an independent mechanic who saw gasoline pooling near the fuel injector, and the coils were leaking between the fuel injector and the fuel rail, and the fuel rail or possibly the injector seals needed to be replaced. The vehicle was not repaired. The contact believed that the vehicle should be included in a recall. The manufacturer was notified of the failure. The failure mileage was approximately 98,000.
- Fuel system, gasoline
The contact owns a 2016 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the contact smelled a gasoline odor in the interior of the vehicle. No warning lights were illuminated. The vehicle was taken to the dealer, who determined that the fuel hose downstream of the…
The contact owns a 2016 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the contact smelled a gasoline odor in the interior of the vehicle. No warning lights were illuminated. The vehicle was taken to the dealer, who determined that the fuel hose downstream of the fuel pump was leaking. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 18V837000 (Fuel System, Gasoline); but the VIN was not included. The manufacturer was notified of the failure but provided no assistance. The failure mileage was unknown.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005276Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2018 C300 | Model year 2016-2018 GLC300 and E300 | ALL model year SLK/SLC300 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2018 C300 and 2016-2018 GLC300 and E300 vehicles. Model year 2015-2017 C300 | Model year 2019 GLC300 and E300 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required.
- 11000623Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2015-2018 (non-hybrid), and ALL model year 172 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for hybrid and model year 2015-2018 vehicles. Model year 2019 (Except model 172 and hybrid variants) Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 10253722Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10246281Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
- 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10243308Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10241531In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 0101D Solenoid valve, crankcase ventilation system Part(s): A 274 090 5600 80 Intake Line Assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilationvalve.) Where applicable, an ECU software update will be provided for certain vehicle variants. Time Allowed: Intake Line Assembly : 5 hours 40 minutes Software Update: 1 hour Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.
- 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
- 10235985This Service Campaign has been initiated because Daimler AG (DAG), the manufacturer of MercedesBenz vehicles, has determined that on the affected vehicles, an additional blind rivet is needed near the front left suspension strut. An authorized Mercedes-Benz dealer will add the additional blind rivet.
- 10235980The following part numbers should no longer be installed and any existing stock on hand must be returned to your facing PDC via Special Return, use Item Category SCM Authorized Part Return; include a copy of the NCA as your authorization to return these parts. This special return will not affect your return allowance and will not be accepted after the specified date. Substitution link were entered into Paragon. Please place orders to replenish your inventory, as needed.
- 10235977Recall Campaign stop-sale order for Fixed Glass Panel on Panoramic sunroof
- 10233783Complaint Loads induced at the steering wheel through pushing and pulling actions may cause creaking and cracking noises in the mechanical steering column. Cause Insufficient grease lubrication in the clamping area of the mechanical steering column. Remedy Grease the clamping area.
- 10231031Staining on door trim strips and top and bottom trim elements on rear side windows. Cause Damage to protective coating of door beltline trim strips, door upper trim strips and side window trim element. Remedy 1. Check if the problem cannot be rectified by polishing the trim bars with the polishing paste. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.
- 10217162Complaint Customer may have one or more of the following complaints: Vehicle location is shown incorrectly in the Navigation Display Navigation destination search is not possible Street names are not shown in Navigation display Apple Carplay is inoperable Cause Improper installation of navigation map data Remedy Follow these steps to delete and re-install map data: Re-format an empty USB drive to NTFS (do not use quick formatting option) Unzip the attached map data deletion file directly to the USB drive. Do not add a folder, only the root files should be shown on the USB drive Generate a pin for the Navigation Delete Database in Vedoc (see attached screenshot) Plug USB drive with map data delete file into the vehicle's USB port and follow instructions in the COMAND Display to delete the installed map data Once the originally installed map data is deleted, then install the newest available map data in Download Manager
- 10217157Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
- 10217154Complaint Thumping noise on rear axle shock absorber on rough road. Cause Until now the rear axle shock absorber support bushing was only available together with the rear axle shock absorber as a replacement part. In future, the rear axle shock absorber support bushing will be available individually as a replacement part to avoid any unnecessary shock absorber noise. Remedy For noise problems on the rear axle shock absorbers, please always make a noise diagnosis, for example using Chassis Ear to localize any sources of noise on shock absorbers or support bushings. If the noise originates from the upper part of the shock absorbers, it is enough to replace the support bushings. Otherwise the complete shock absorber including support bushing have to be replaced. The modified support bushings must be replaced in pairs the first time so that any mixed installation of old and new is reliably ruled out.
- 10209877Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy Follow guided tests as described.
- 10209874Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain MY 2015-2018 C-Class and GLC-Class (205 and 253 platform) vehicles, the software for the powertrain control unit may not correspond to the current production specifications. It is possible that the next maintenance interval is displayed to the user as a negative distance reading in the instrument cluster. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the powertrain control unit software.
- 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
- 10207205Complaint Seat heating on driver's seat and front passenger seat nonfunctional. The LEDs on the switches for the seat heating illuminate, but the seat heating mats do not get warm. Cause Faulty SCN coding of rear SAM. Remedy Perform SCN coding of rear SAM (BC_R). Commission seat heating control unit.
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
Every Mercedes-Benz C300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.