2021 Mercedes-Benz C 300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › C 300 › 2021
These records cover every 2021 Mercedes-Benz C 300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2021 Mercedes-Benz C 300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such…
Risk and remedy
Risk
An inoperable rearview camera display reduces the driver's rear view, increasing the risk of a crash.
Remedy
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed July 15, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022060007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 C300 Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63 AMG S Cabriolet, E450 Cabriolet, and E53 AMG Cabriolet vehicles. The rear headrests may be incorrectly mounted to the seatbacks.
Risk and remedy
Risk
Incorrectly mounted headrests could move or detach from the seat during a crash, increasing the risk of injury.
Remedy
Dealers will inspect the rear seatback guide bushings and replace them if necessary, free of charge. Owner notification letters were mailed July 16, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021060010.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 C-Class, E-Class, E-Class Coupe and Convertible, GLC, CLS, AMG GT 4-door Coupe and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. A faulty electrical contact within the seat position switch may prevent the driver and passenger air bags and seat belt force…
Risk and remedy
Risk
Air bags and seat belts that do not perform properly in a crash can increase the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the seat position switches, free of charge. Owner letters were mailed May 21, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040016.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2021 C300, 2017-2020 AMG C43, and AMG C63 vehicles. The front seat belts might not fully retract to their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Risk and remedy
Risk
If the seat belt does not fully retract, the occupant may find the operation of the seat belt inconvenient and not wear it, increasing the risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will check the retraction function of the front seat belts and adjust the damping foam within the B-pillars, as necessary, free of charge. The recall began February 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021020010.
Owner complaints
14 complaints
What owners report most
Latest complaints
- Engine
The contact owns a 2021 Mercedes-Benz C 300. The contact stated that while depressing the accelerator pedal, there was a loud knocking sound coming from the engine compartment while accelerating. There were no warning lights illuminated. The vehicle was taken to the dealer to be diagnosed, and it…
The contact owns a 2021 Mercedes-Benz C 300. The contact stated that while depressing the accelerator pedal, there was a loud knocking sound coming from the engine compartment while accelerating. There were no warning lights illuminated. The vehicle was taken to the dealer to be diagnosed, and it was determined that the spawn rod was fractured, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The contact stated that the engine was previously repaired because of the head gasket failure in 2024. The manufacturer was informed of the issue, and a case was opened. The failure mileage was approximately 88,000.
- Fuel system, gasoline
The contact owns a 2021 Mercedes Benz C. The contact stated that while driving on the highway, the vehicle began to lose power, riding rough. The check engine light illuminated. The vehicle was towed to the dealer where it was diagnosed with a fuel injection failure. The vehicle read diagnostic code P1CEF85. The manufacturer was made aware of the issue. The approximate failure mileage was 60,000.
- Visibility › Sun/moon roof assembly
I am reporting a safety defect involving the panoramic sunroof on my 2021Mercedes-Benz Coop vehicle. The panoramic sunroof has malfunctioned due to an apparent design or manufacturing defect. The sunroof fails to open / close and makes grinding or popping noises which malfunctioned unexpectedly.…
I am reporting a safety defect involving the panoramic sunroof on my 2021Mercedes-Benz Coop vehicle. The panoramic sunroof has malfunctioned due to an apparent design or manufacturing defect. The sunroof fails to open / close and makes grinding or popping noises which malfunctioned unexpectedly. This issue occurred without misuse and during normal operation of the vehicle. The defect creates a safety concern because it can distract the driver, allow water intrusion that may affect electrical components, and/or cause sudden glass or mechanical failure while driving. The vehicle has been taken to a Mercedes-Benz dealership for diagnosis and the issue was not resolved due to denied coverage. I was informed that the repair would be costly despite the issue appearing to be a known defect in Mercedes-Benz panoramic sunroof systems. I believe this defect may affect other Mercedes-Benz vehicles with panoramic sunroofs and should be investigated for a potential safety defect or recall.
- Engine
The contact owns a 2021 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the vehicle stalled and failed to exceed 30 MPH, with the check engine warning light illuminated. The vehicle did not require a restart. The contact also stated that while stopped at a traffic…
The contact owns a 2021 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the vehicle stalled and failed to exceed 30 MPH, with the check engine warning light illuminated. The vehicle did not require a restart. The contact also stated that while stopped at a traffic light, the vehicle was shaking abnormally. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that there was a misfire in cylinder #2. The contact was informed that the cylinder head needed to be replaced. The vehicle was not repaired. The vehicle was then taken to the dealer, where the same diagnostic information was provided, and the contact was informed that the cylinder head needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 86,078.
- Engine
2021 Mercedes-Benz C300 with M254 2.0L turbo engine experienced sudden cylinder head failure at 44,000 miles due to manufacturing porosity in the cylinder head and camshaft bore scoring. Dealer confirmed defect. This is a known, recurring issue on 2021–2023 M254 engines with multiple documented…
2021 Mercedes-Benz C300 with M254 2.0L turbo engine experienced sudden cylinder head failure at 44,000 miles due to manufacturing porosity in the cylinder head and camshaft bore scoring. Dealer confirmed defect. This is a known, recurring issue on 2021–2023 M254 engines with multiple documented failures under 50k miles. Sudden loss of compression and misfires create a safety risk of engine failure or fire while driving. TSB NUMBER LI07.16-P-074000 (February 2023, updated multiple times). This is a known production/early break-in issue with the M254 engine, not the result of owner misuse or delayed maintenance.
- Fuel/propulsion system
My car had a coolant leak last year a hose broke and I have a 2021. My son’s mercedes sis the same thing on 11/23/2025. I have researched ma y others with this same issue. There should be a recall on that hose or whatever the problem Is.
- Fuel/propulsion system
While driving car on Sunday 10/5, it suddenly failed to respond to gas pedal pressure. The car stopped accelerating and rather slowed to 15 MPH, almost causing a car from behind to hit me in the rear side.
- Engine · Power train
My C300 only had about 42,000 miles and was less than 5 years old. Just after the factory warranty expired, the engine was running rough and hot, and "check engine" light illuminated. My local garage quickly diagnosed the problem as a failed cylinder head, stated that it is common with Mercedes…
My C300 only had about 42,000 miles and was less than 5 years old. Just after the factory warranty expired, the engine was running rough and hot, and "check engine" light illuminated. My local garage quickly diagnosed the problem as a failed cylinder head, stated that it is common with Mercedes 4-cylinder engines from about 2017, and said Mercedes may cover it since it is a "known problem" and shouldn't happen with that mileage. I was charged $7,860 by my local Mercedes dealer, and despite multiple contacts with MercedezUSA, they refuse to acknowledge this is a problem or cover the cost, although in on-line the forums some people were arbitrarily reimbursed. There should be a recall to check for this obvious defect and should be covered. This defect can cause sudden engine failure and is a significant hazard to the driving public.
- Engine
Cylinder head needed to be replaced on the M264 engine at 35,000 miles. The replacement part is also known to be defective for the same reasons. This is a common defect known to the manufacturer and they have not issued a recall. My concern is that of a roadside breakdown that would endanger my wife and myself. Thank you for your consideration.
- Back over prevention › Sensing system › Camera
Rearview camera not displaying any image when transmission is put in reverse.
- Engine
the check Engine light fault code P012D12 The pressure sensor upstream of the turbocharger had a short circuit to positive. Found Kink wire on upstream pressure sensor. A short circuit to positive. Electrical Wire replaced.
- Electrical system · Engine
First day leasing the vehicle within 6 hours lights malfunction and malfunction warning on dash to seek workshop, vehicle was taken for inspection to original dealer (Mercedes Benz of Bakersfield). During inspection I added additional concerning complaints about passenger door not closing…
First day leasing the vehicle within 6 hours lights malfunction and malfunction warning on dash to seek workshop, vehicle was taken for inspection to original dealer (Mercedes Benz of Bakersfield). During inspection I added additional concerning complaints about passenger door not closing correctly/wind noise seeping through when closed, and hood not closing promptly. One month into leasing vehicle passenger window malfunction, took for inspection and repair to original dealer (MBofBakersfield). Concerned with caution for me, my family, and friends when in that vehicle for giving faulty signs so early. One year into leasing vehicle check coolant warning on dash, took for inspection to original dealer. I am now more concerned as it went form electrical to coolant components losing coolant with no reasoning from original dealer service other then a top off. Vehicle drive is rough. 1 year and 6 months into leasing vehicle, again check coolant warning on dash. Took in for inspection, gave no reasoning from original dealer service dept, other then a top off done. Vehicle drives rough. While driving 70mph, a vehicle behind was approaching quick when I went to excel to merge vehicle seemed to be slipping in gear/slow down. No warning lamps on, Quickly decided/managed to merged to next lane so vehicle behind didn’t hit us as we were slowing down With 2 children in the back seat. decided to exit to nearest exit to pull off as it felt unsafe to drive, as exiting and slowing down vehicle began to shake, knock, and make loud bangs. Managed to pull over, and check dash for messages for any type of warnings. No warning lamps, but many symptoms of a faulty unsafe vehicle. Had vehicle towed to original dealer service for diagnosis and report the unsafety incident that occurred with absolutely no warning lamps. Inspection lead to repair of engine but nothing done about no warning lamps/electrical system
- Engine
Piston Connecting Rod broke and left the engine making holes in both sides of the block; Mercedes Benz rejected any responsibility because the car has a branded title. Currently a new engine (brand new) is being installed, my concern is that what will happen if the new engine has the same defective part and blew up again.
- Air bags
The contact owns a 2021 Mercedes-Benz C300. The contact stated while driving at an unknown speed, there was a burning odor inside the vehicle. The contact stated the passenger side air bags was enabled warning light was illuminated. The contact also stated the vehicle made an abnormal noise. The…
The contact owns a 2021 Mercedes-Benz C300. The contact stated while driving at an unknown speed, there was a burning odor inside the vehicle. The contact stated the passenger side air bags was enabled warning light was illuminated. The contact also stated the vehicle made an abnormal noise. The contact took the vehicle to the local dealer but was unable to duplicate the failure. The manufacturer had not been informed of the failure. The failure mileage was unknown.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006710Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005314Complaint Yellow Coolant warning comes on in cluster Fault codes below are current or stored in MED41 P0A0500- The actuation of the circulation pump for the low-temperature circuit has an open circuit. P00B700- The coolant flow is too low. P0C7300- Circulation pump 1 for the low-temperature circuit has a malfunction. Cause Air may be trapped in the coolant circuit for transmission cooler Remedy Check coolant level. -If coolant level is low, locate source of leak and correct. -If coolant level is ok, perform procedure in attached instructions to bleed the coolant circuit to transmission cooler. 1. Allow cooling system to cool to ambient temperature. 2. Fill coolant reservoir completely. 3. Slightly open coolant connection shown in attachment (red arrow) to allow air to escape. 4. Once coolant flows out, close connection and correct coolant level. 5. Clear fault codes and check for further symptoms.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003218Complaint Complaints about shift quality in vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2. Cause If the shift adaptation is not performed as described under "Remedy", the adaptation values may not be saved correctly under certain circumstances. Remedy In vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2, it must be ensured that the adaptation of the shifts is performed only as described below. Acceleration upshifts may only be adapted in transmission mode "S" Acceleration downshifts may only be adapted in transmission mode "S" Coast down shifts may only be adapted in transmission mode "E"
- 11003212Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. 3. NOTE: Coding Parameter 'Shimmy' should be turned off and the actual value should read "Shimmy aus". With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11003205Complaint The driver's seat memory settings do not synchronize with the driver's user profile as described in the operator's manual. Driver's seat settings are not transferred to the vehicle. Cause The driver's seat does not support the profile synchronization feature on these vehicles. Remedy There is no remedy for this complaint. The vehicle is working as designed. Note: Do not replace any parts.
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 11000518Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 C-Class and S-Class vehicles (206, 223 platform), the software for the ISA control unit may not correspond with the latest series production configuration. The possibility exists that the function of the ISA may not be restricted with an active Malfunction Indicator Lamp. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the ISA control unit software in the affected vehicles.
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10252732This is to notify you of the Service Campaign OTA update for the MBUX control unit software in 14,559 Model Year (MY) 21-23 C-Class, S-Class, SL, EQS (206, 223, 232, 297 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 C-Class, S-Class, SL, and EQS vehicles (206, 223, 232, 297 platform), the MBUX System software does not correspond with the latest series production configuration. The MBUX control unit will receive an OTA update that includes functional improvements and new features such as: Dolby Atmos, video streaming, personalized images on the front passenger display, and additional commands for the MBUX Voice Assistant. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10251192Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 21-24 C-Class, EQE, EQS, GLC, GLE, GLS, S-Class, SL (206, 294, 295, 296, 297, 254, 167, 223, 232 platform) vehicles, the MBUX System software does not correspond with the latest series production configuration. The MBUX control unit will receive an OTA update that includes functional improvements and new features such as: Dolby Atmos, video streaming, personalized images on the front passenger display, and additional commands for the MBUX Voice Assistant. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
- 10249740Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
- 10248210Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, EQE, EQS, S-Class (206, 294/295, 296/297 and 223 platform) vehicles, the inductive charging system software does not correspond with the latest series production configuration. The inductive charging system will receive an OTA update that includes improvements for the wireless charging of the Apple iPhone 14 and subsequent generations with MagSafe. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this OTA software update.
- 10248206Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, EQE, EQS, S-Class (206, 294/295, 296/297 and 223 platform) vehicles, the inductive charging system software does not correspond with the latest series production configuration. The inductive charging system will receive an OTA update that includes improvements for the wireless charging of the Apple iPhone 14 and subsequent generations with MagSafe. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
Every Mercedes-Benz C 300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.