2016 Mercedes-Benz CLA250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › CLA250 › 2016
These records cover every 2016 Mercedes-Benz CLA250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2016 Mercedes-Benz CLA250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2018 CLA250 and CLA250 4MATIC, and 2017-2018 CLA45 AMG vehicles. The Occupant Classification System (OCS) may have been improperly calibrated, which may prevent the proper deployment of the front passenger air bag.
Risk and remedy
Risk
In the event of a crash, if the air bag does not deploy as designed, the front seat passenger has an increased risk of an injury.
Remedy
MBUSA will notify owners, and dealers will replace the passenger seat cushion, free of charge. The recall began July 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060012.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…
Risk and remedy
Risk
If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450…
Risk and remedy
Risk
If the starting current limiter overheats, the surrounding components can melt, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will install an additional fuse in the electrical line to the starter, free of charge. The recall began August 31, 2017. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2017080002.
Owner complaints
67 complaints5 involved a crash1 involved a fire4 injuries1 deaths
What owners report most
Latest complaints
- Air bags · Electrical system · Steering
While turning my steering wheel during normal operation, I heard what appeared to be a popping or snapping sound from inside the steering wheel. Immediately afterward, my horn stopped working, all steering-wheel control buttons became inoperative, and the airbag warning light illuminated with the…
While turning my steering wheel during normal operation, I heard what appeared to be a popping or snapping sound from inside the steering wheel. Immediately afterward, my horn stopped working, all steering-wheel control buttons became inoperative, and the airbag warning light illuminated with the message “Front Left Malfunction – Service Required.” All these failures occurred suddenly and at approximately the same time, without any prior warning or symptoms. The instrument cluster still lights up, but I can no longer access the mileage display using the steering-wheel controls. The last mileage I recall was approximately 80,000 miles. These symptoms suggest a possible steering-column clock spring failure, although the exact cause has not yet been professionally diagnosed. I am particularly concerned because NHTSA recall 17V627000 previously addressed a safety risk involving the steering-column clock spring and driver’s airbag system. Mercedes-Benz lists this recall as completed for my vehicle. However, the recall remedy did not routinely replace the clock spring, and my vehicle has now experienced symptoms consistent with its failure. This vehicle was also purchased as a Mercedes-Benz Certified Pre-Owned vehicle with an extended warranty and was represented as having undergone a comprehensive inspection, including safety-related systems. My concern is that a clock spring or related steering-column electrical component may fail suddenly, disabling the horn and potentially compromising the driver’s airbag, even after the previous recall remedy was completed. I request that NHTSA investigate whether similar failures are occurring in other vehicles, whether an ongoing safety defect exists, and whether additional corrective action or an expanded recall may be warranted.
- Fuel/propulsion system
My 2016 Mercedes-Benz CLA 250 has a check engine light for code P052E, which points to a broken crankcase ventilation valve. My car has only 59,000 miles on it, but this same exact part already broke once before and was replaced under the original warranty. Now, the replacement part has failed too.…
My 2016 Mercedes-Benz CLA 250 has a check engine light for code P052E, which points to a broken crankcase ventilation valve. My car has only 59,000 miles on it, but this same exact part already broke once before and was replaced under the original warranty. Now, the replacement part has failed too. This proves the part is defective and keeps breaking. Mercedes-Benz already knows this part is defective. They gave a free 15-year or 150,000-mile extended warranty to fix this exact issue for free on the C-Class and other longitudinal M274 engine platforms. However, they are actively denying coverage for my CLA 250's M270 engine variant, despite the two vehicles sharing nearly identical engine blocks, matching subcomponents, and the exact same broken part. Because of this unfair engine code technicality, Mercedes-Benz is forcing CLA owners to pay thousands of dollars out of pocket for a recurring problem they fix for free on a C-Class. I urge the NHTSA to look into this engine loophole and force Mercedes-Benz to include the M270 engine variants under the 15-year/150,000-mile free repair program.
- Unknown or other
I believe that my vehicle is subject to Recall Campaign # 21V197000. The vehicle is a 2016 Mercedes-Benz CLA250. I've had to have this part ( Front Stationary Roof panel) adhered 5 times in the last 10 months. Mercedes refuses to acknowledge the above campaign #. Not only is this a safety risk to…
I believe that my vehicle is subject to Recall Campaign # 21V197000. The vehicle is a 2016 Mercedes-Benz CLA250. I've had to have this part ( Front Stationary Roof panel) adhered 5 times in the last 10 months. Mercedes refuses to acknowledge the above campaign #. Not only is this a safety risk to my self and other drivers, there is risk of water damage any electrical components. When this issue was brought to their attention I was told this was VIN specific and no recalls were attached to this vehicle. The photos are from 2 separate incidents. There are no warning lights. My vehicle has had at least 2 unbiased inspections and available upon requet.
- Air bags · Steering
My mechanic said that he believes there is a recall on a recalled part this was previously repaired per Mercedes notice of safety recall dated April 2018. The recall remedy provided by the manufacturer has failed to permanently fix the safety defect, and the vehicle remains unsafe to drive. "On…
My mechanic said that he believes there is a recall on a recalled part this was previously repaired per Mercedes notice of safety recall dated April 2018. The recall remedy provided by the manufacturer has failed to permanently fix the safety defect, and the vehicle remains unsafe to drive. "On certain Model Year (“MY”) 2014-2017 B-Class electric, MY 2012-2018 C-Class, MY 2012-2017 E-Class, MY 2014-2018 CLA, MY 2015-2018 GLA, MY 2016-2018 GLC, and MY 2013-2015 GLK-Class vehicles, an electrostatic discharge, when combined with a broken steering column module clock spring and an insufficient grounding of the steering components, could lead to an inadvertent deployment of the driver airbag. An inadvertent driver airbag deployment may cause a risk of injury to the driver and might increase the risk of a crash." Currently my airbag and horn do not work as a result of this defect and Mercedes said there is no current safety recalls, however this is the exact issue that was replaced and fixed before I purchased it. They want to charge me a $300 diagnostic fee, (when my mechanic has already looked at it), I am not wanting to pay the dealership for an issue that is clearly related to the recall issue that was not properly fixed. My car is a safety issue to myself and anyone if I drive it, my horn does not work, so that makes it hard to prevent accidents and my airbag, upon reading further online, could potentially deploy and CAUSE and accident.
- Air bags · Steering
My mechanic said that he believes there is a recall on a recalled part this was previously repaired per Mercedes notice of safety recall dated April 2018. The recall remedy provided by the manufacturer has failed to permanently fix the safety defect, and the vehicle remains unsafe to drive. "On…
My mechanic said that he believes there is a recall on a recalled part this was previously repaired per Mercedes notice of safety recall dated April 2018. The recall remedy provided by the manufacturer has failed to permanently fix the safety defect, and the vehicle remains unsafe to drive. "On certain Model Year (“MY”) 2014-2017 B-Class electric, MY 2012-2018 C-Class, MY 2012-2017 E-Class, MY 2014-2018 CLA, MY 2015-2018 GLA, MY 2016-2018 GLC, and MY 2013-2015 GLK-Class vehicles, an electrostatic discharge, when combined with a broken steering column module clock spring and an insufficient grounding of the steering components, could lead to an inadvertent deployment of the driver airbag. An inadvertent driver airbag deployment may cause a risk of injury to the driver and might increase the risk of a crash." Currently my airbag and horn do not work as a result of this defect and Mercedes said there is no current safety recalls, however this is the exact issue that was replaced and fixed before I purchased it. They want to charge me a $300 diagnostic fee, (when my mechanic has already looked at it), I am not wanting to pay the dealership for an issue that is clearly related to the recall issue that was not properly fixed. My car is a safety issue to myself and anyone if I drive it, my horn does not work, so that makes it hard to prevent accidents and my airbag, upon reading further online, could potentially deploy and CAUSE and accident.
- Structure › Body › Roof and pillars
My vehicle is exhibiting the same problem as MB Recall Campaign #2021070010 but my MB Vin is not included in the recall even though my make/model of car is on the list. This MB recall campaign is to replace the front stationary sunroof panel. According to recall,"The panoramic sunroof may not have…
My vehicle is exhibiting the same problem as MB Recall Campaign #2021070010 but my MB Vin is not included in the recall even though my make/model of car is on the list. This MB recall campaign is to replace the front stationary sunroof panel. According to recall,"The panoramic sunroof may not have been bonded correctly to the vehicle. The adhesion of the front panel might partially or fully detach from the vehicle increasing the risk/injury to other road users." This campaign which was updated 9/3/2021 should include ALL vehicles on the recall list that exhibit this issue. I contacted an authorized MB dealer show quoted me $2225.41 for a repair that we know is known DEFECT. PLEASE HELP!
- Structure › Body · Unknown or other · Visibility/wiper
Factory window tint of the back window & the driver/passenger side(s) windows are bubbling and peeling causing visual impairment while operating motor vehicle. Examples of impairment are backing the vehicle and changing lanes & these affected areas are blurry. Panaramic Sunroof does not seal properly when closed. Factory vehicle paint bubbling and peeling causing depreciation of the vehicle.
- Unknown or other
The incident that occurred is that my sunroof exploded on me while I was driving. There was know one in front of me nor next to me. Nothing hitting it to cause this, it just exploded.
- Structure › Body
Hi there - I know my vin number doesn't recall the front stationary roof panel replacement but this came to my attention as I saw that the panel has faded the top coating and the edges have some very thin cracks I will say. I was not aware of such a thing but googling the issue I found out that…
Hi there - I know my vin number doesn't recall the front stationary roof panel replacement but this came to my attention as I saw that the panel has faded the top coating and the edges have some very thin cracks I will say. I was not aware of such a thing but googling the issue I found out that NHTSA did start a campaign for this particular safety issue last year. Campaign No. 2024010012, March 2024. My Mercedes falls completely on the requirements for repairing/replacing this front panel as the model, year, and type of material of this panel but yet no recall with my vin number. Just wondering if this is a mistake or something else that I don't know. For now I haven't driven the car for the safety concerns until I have any explanations. Your response in this matter will be very appreciated ! Thank you, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system · Seats · Unknown or other
My 2016 CLA 250 having multiple electrical and driving issues that are not recalled. I’ve researched online and found most of these issues are common. 1. Dashboard screen and radio console lights turn off completely. USB connection triggers electrical symptoms. Front and Back seat window control…
My 2016 CLA 250 having multiple electrical and driving issues that are not recalled. I’ve researched online and found most of these issues are common. 1. Dashboard screen and radio console lights turn off completely. USB connection triggers electrical symptoms. Front and Back seat window control (driver) triggers electrical symptoms and sometimes corrects the problems. Trunk opens by itself while parked and/or stopped at red lights. The instrument cluster has times multiple warning lights turn on and stay on. At times the fuel needle drops completely down as if I have no fuel in the car. The instrument cluster lights stay on after I have turned the car off and locked it as if the system is confused. I have more issues but those are a few to name. I also have video and pictures to prove these things happen randomly then the vehicle can go back to operating normally. I’ve taken it to service and all they have done is reset the warnings.
- Engine and engine cooling
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer where it was diagnosed with a failed thermostat. The contact was informed that the thermostat needed to be…
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer where it was diagnosed with a failed thermostat. The contact was informed that the thermostat needed to be replaced. The vehicle was not repaired. The vehicle was driven to the residence. The contact performed an inspection on the vehicle and determined there was a melted hole in the air intake valve. The contact stated that the dealer had not provided information of the condition of the melted air intake valve. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 116,000.
- Electrical system · Engine · Unknown or other
Check engine light with error code P052E. From my research, this is a very common issue with this engine and one that either has been recalled or is planning to be recalled. According to some online forums for Mercedes Benz, Mercedes is being sued over this problem and has issued an extended…
Check engine light with error code P052E. From my research, this is a very common issue with this engine and one that either has been recalled or is planning to be recalled. According to some online forums for Mercedes Benz, Mercedes is being sued over this problem and has issued an extended warranty on certain models because of how common this problem has become. The list of models needs to be expanded to include other models experiencing the same problem.
- Electrical system · Engine · Fuel/propulsion system
Vehicle Performance Issues - Detailed Timeline [XXX] •First issue occurred: the car wouldn’t start at a store. Engine turned over, failed to start. •After sitting overnight, it would start but stall after 10 minutes of driving. •Parked the car and began using alternative transportation. •Diagnostic…
Vehicle Performance Issues - Detailed Timeline [XXX] •First issue occurred: the car wouldn’t start at a store. Engine turned over, failed to start. •After sitting overnight, it would start but stall after 10 minutes of driving. •Parked the car and began using alternative transportation. •Diagnostic tests by three mechanics revealed the following codes: oP0087: Fuel Rail/System Pressure Too Low. oP052E: Crankcase Ventilation (PCV). [XXX] •Picked up the car from Midland Mercedes after repairs. Paid $3,069.16 for crankcase ventilation service. •Mercedes Customer Summary Report had no reference to any fuel-related issues or the P0087 code. •Drove 10 minutes to a gas station; the car wouldn’t start, repeating the same issue of why I brought it in to have repaired. •Returned to the shop; Said a New Code came up and replaced the fuel pump: oCost of part: $670.47 (no labor charged). I refused to pay $2200! [XXX] •Finally after 3 months! I got my car and drove back to San Angelo on half a tank, avoiding stops to prevent starting problems. I now had PTSD! •Filled the tank upon arrival; no issues that day. [XXX] •On the way to work, turned on the heat and noticed: oA strong gas odor inside the car. oThe radio volume control wasn’t working, and the ECO mode indicator wasn’t functioning as usual. [XXX] Filled the gas tank halfway to reduce the gas smell. •1st start up cycle immediately after getting gas, no issue. •2nd start up cycle , the dashboard lights started flickering and all indicator lights came on. Traction control warning along with message to check the owner’s manual. Can not accelerate. Check engine light stays on. •3rd cycle start up, all lights turned off except the check engine light. •4th cycle start up, no check engine light This occurs every time I get fuel. I only get $10 at a time. Noticing the pattern, I coded the car. A new code came up. •P2187: System Too Lean at Idle (Bank 1). INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine
My car has slipped into neutral twice while driving. Once while turning left from red light and once while sitting still at red light.
- Engine
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer where it was diagnosed that the regulator valve had failed and needed to be replaced. The vehicle was not…
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer where it was diagnosed that the regulator valve had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 50,000.
- Electrical system · Power train
When we are driving the transmission slip intro neutral ramdomly message appear « do not shift in gear, visit dealer » we need to stop the car on the high way put it in park and after in drive . Its happen really often and my wife d’ont want to drive it any more because its to dangerous with kid, we need a solution
- Visibility › Sun/moon roof assembly
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated that while driving at approximately 55 MPH, there was a loud explosion coming from the vehicle. The contact later pulled over, and upon inspection, discovered that the sunroof glass had shattered. The contact stated that there was no…
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated that while driving at approximately 55 MPH, there was a loud explosion coming from the vehicle. The contact later pulled over, and upon inspection, discovered that the sunroof glass had shattered. The contact stated that there was no impact to the sunroof that could have caused the sunroof glass to shatter. The vehicle was taken to an auto glass retailer, who installed a plastic cover over the sunroof; however, the sunroof glass was not replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 125,000.
- Unknown or other
Mercedes CLA 250 2016 rear differential breakdown Making noise
- Engine · Fuel/propulsion system · Unknown or other
I HAVE 2 MECEDES WITH THE SAME ISSUE PER MERCEDES BENZ OF USA INSPECTION CAUSING ENGINE LIGHT TO BE TRIGGERED PER DIAGNOSIS TESTING RAN ON BOTH CARS. 2015 VIN [XXXXX] GLA 250 4 MATIC-P052E71 2016 VIN [XXXXX0 2013 CLA 250 MATIC -P052E71 I WAS TOLD BY A MERCEDES SERVICES ADVISIOR THAT BOTH CARS HAVE…
I HAVE 2 MECEDES WITH THE SAME ISSUE PER MERCEDES BENZ OF USA INSPECTION CAUSING ENGINE LIGHT TO BE TRIGGERED PER DIAGNOSIS TESTING RAN ON BOTH CARS. 2015 VIN [XXXXX] GLA 250 4 MATIC-P052E71 2016 VIN [XXXXX0 2013 CLA 250 MATIC -P052E71 I WAS TOLD BY A MERCEDES SERVICES ADVISIOR THAT BOTH CARS HAVE THE SAME ENGINE FOR A 2015GLA AND A 2016 CLA - BOTH Due to both cars stalling in traffic on multiple time when driving I took both to the shop to run further testing to discover both had the same engine light trigger which is the CRANKSHAFT (AKA) OIL SEPERATOR (AKA)INTAKE TUBE DUE TO THIS BOTH CARS HAVE SUFFERED AN ISSUE WHEN TAKING EMMISSION TEST - MERCEDES DIGNOSIS TESTING CODES -P052E71 - CRANKSHAFT VENILATION MALFUNCTION - CAR WILL NOT PASS EMMISSION TEST AND THIS PART DEFECTS ALSO CAUSES CAR TO STALL THAT CAN POSSIBLE CAUSE ACCIDENT THIS PART COMPLETE REPAIR COULD COST UP TO $2500-$3000 FOR PARTS AND LABOR PART NUMBER -270-090-07-00 (CRANKSHAFT) THE ENGINE LIGHT ISSUE TRIGGERED BY CRANKSHAFT AND WILL NOT PASS EMMISSION TESTING DUE TO THIS Description of this part below: Crankcase Ventilation is the process of venting or removing blow-by from an engine's crankcase to prevent excessive pressure build-up within the engine. Blow-by gases are mixed with oil mist and other contaminants that can harm an engine's internal components and contaminate the environment. How does the crankshaft ventilation work- When the vehicle is moving, airflow across the open end of the tube creates suction (a "draught" or draft) that pulls gases out of the crankcase. To prevent too much vacuum being created, the blow-by gases are replaced by fresh air using a device called a breather. The breather is often located in the oil cap the engine misfires, you may have trouble getting your vehicle up to speed. Misfires often happen when your vehicle is under load while accelerating. This can result in slow or sluggish acceleration or a jerking motion while pressing down on acc
- Seat belts
The right passenger seat belt is faulty.
- Structure › Body · Unknown or other
There is a service recall campaign for my model car but dealer/mercedes usa doesn't have the recall linking my car to it from my VIN. Campaign number is P-RC-2021070010. It is to replace the front stationary sunroof panel because it may not have been bonded correctly and could fly off and hit someone. My vehicle did have this same part rattle in 2017 during a cross-country trip.
- Fuel/propulsion system
Subject: Urgent Safety Concern Regarding Recall Campaign #2022030003 for 2016 CLA250 VIN# xxx Date: August 16, 2023 To Whom It May Concern, I am writing to express my deep concern and dissatisfaction regarding a recent incident involving my 2016 CLA250, VIN# xxx, which has raised serious safety…
Subject: Urgent Safety Concern Regarding Recall Campaign #2022030003 for 2016 CLA250 VIN# xxx Date: August 16, 2023 To Whom It May Concern, I am writing to express my deep concern and dissatisfaction regarding a recent incident involving my 2016 CLA250, VIN# xxx, which has raised serious safety issues for both myself and my passengers. Between July 15, 2023, and August 14, 2023, I experienced a distressing loss of power while commuting to work. The incident occurred while I was traveling in the high-speed lane on the highway, almost resulting in a major accident that could have led to severe injuries or even loss of life. During this period, the check engine light on my vehicle illuminated and subsequently turned off. Fearing for our safety, I promptly sought a vehicle diagnostic assessment at the Firestone Service center on August 15, 2023. The diagnostic codes returned indicated a "Fuel/Rail Low Power" issue. To my dismay, I learned that a recall (Campaign #2022030003) had been issued by the manufacturer for the exact problem I encountered. With this information in hand, I diligently contacted the local Mercedes dealership to address the recall. However, I was informed that my vehicle's VIN# was not included in the recall list. This contradicts the diagnostic assessment carried out by Firestone, which clearly indicated the need for intervention due to the "Fuel/Rail Low Power" issue. Given the alarming circumstances and the potential risks associated with this safety concern, I implore you to investigate and rectify this situation promptly. It is evident from the diagnostic results obtained from Firestone that my 2016 CLA VIN# xxx should be included in the recall list to ensure the safety of all occupants. I trust that the National Highway Traffic Safety Administration (NHTSA) plays a pivotal role in safeguarding the well-being of motorists and passengers across the nation. I kindly request your urgent attention to this matter to prevent any further incide
- Air bags
May 3, 2023 - I had pulled back into my driveway approximately at 8:45 AM after leaving a couple of minutes before to run errands. I turned the car off and went inside of my house for less than five minutes. I got back into my car, started the vehicle and the airbag exploded unexpectedly while I…
May 3, 2023 - I had pulled back into my driveway approximately at 8:45 AM after leaving a couple of minutes before to run errands. I turned the car off and went inside of my house for less than five minutes. I got back into my car, started the vehicle and the airbag exploded unexpectedly while I was in my driveway. Of course, I was shocked and confused as to what had happened. My husband was inside the house and came out to check on me. I received surface burns on both of my forearms, my left pinky finger was bent in an unnatural position and part of my left pinky fingernail was missing. It was a true blessing that I was in my driveway and not driving on the open road. I went to the doctor a few hours later to get checked out, where it was confirmed by x-rays that I had fractured my left pinky finger, which made it very difficult to do my job. I was traumatized from this incident to say the least. My car sat at the end of my driveway in the same place where the airbag deployed until May 10th. May 9, 2023 - I made my first call to Mercedez Benz USA Care to report what had happened with my Mercedes 2016 CLA250 the previous week and for them to advise me as to what I shoud do. I was advised by MBUSA care representative to have my car towed to an authorized Mercedes Benz Dealership in Kansas City. Because of the late hour of the business day, I decided to have the car towed to the dealership the next day. May 10, 2023 - The vehicle was towed to an authorized Mercedes dealer, Aristocrat Motors in Kansas City. From what I've been told, my vehicle was inspected some time during the last half of June. Because this is considered a legal matter by MBUSA, I have not received any further communication from them. My car has been in "lock down" at the dealership since in was towed there on May 10th. I have reached out to the referral manager at MBUSA on countless occasions via both telephone and email. We have made three car payments and have no car to drive.
- Visibility › Sun/moon roof assembly
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated that while driving at approximately 70 MPH, the vehicle made an abnormal sound. The contact noticed that the moonroof had fractured in half and then detached. The contact related the failure to NHTSA Campaign Number: 21V197000…
The contact owns a 2016 Mercedes-Benz CLA250. The contact stated that while driving at approximately 70 MPH, the vehicle made an abnormal sound. The contact noticed that the moonroof had fractured in half and then detached. The contact related the failure to NHTSA Campaign Number: 21V197000 (Structure). The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 80,000.
- Fuel system, gasoline
The contact owned a 2016 Mercedes-Benz CLA250. The contact stated that while idling or driving at various speeds, she noticed a fuel odor throughout the vehicle. The fuel warning light illuminated indicating low fuel level. The ABS warning light was intermittently illuminated. Additionally, the…
The contact owned a 2016 Mercedes-Benz CLA250. The contact stated that while idling or driving at various speeds, she noticed a fuel odor throughout the vehicle. The fuel warning light illuminated indicating low fuel level. The ABS warning light was intermittently illuminated. Additionally, the contact stated that after refueling the vehicle, the fuel gauge remained on empty. The vehicle was not diagnosed or repaired. The dealer was notified of the failure and an appointment was scheduled. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 62,000.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10246281Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205841Spare wheel.
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205237The COMAND unit does not start or the display remains dark.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205218New roller blind with blind bearing does not fit in previous panoramic with old roof mechanisms or blind guide rails.
- 10205200Parktronic inoperable.
- 10205156Intial startup not possible after replacement of transmisson 725.0 or of electrohydraulic controller unit.
- 10205154Gasket may settle causing a slight oil leak.
- 10199675Vibrations/ humming when moving off or maneuvering with the wheels turned
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179907Engine diagnosis warning lamp activated - Fault code P012800
- 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
- 10178713Headlamps fogged
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10172683Information Label on Tire Sealant
- 10171637Retrofitted front door exit lamps with logo projection flicker
- 10169602Replace Steering Gear Bolts
- 10169599Squeaking Noise from Exhaust Gas Flap
- 10167551Vehicle wanders to the left or right.
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167518Creaking noises in area of center console
Every Mercedes-Benz CLA250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.