2017 Mercedes-Benz CLA250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › CLA250 › 2017
These records cover every 2017 Mercedes-Benz CLA250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
10 recalls name the 2017 Mercedes-Benz CLA250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 B250e, CLA250, 2017-2018 AMG CLA45, GLA250, and AMG GLA45 vehicles. The steering shaft bore hole for the universal joint bearing may allow excessive movement that, over time, could result in the separation of the bearing and universal joint.
Risk and remedy
Risk
A separated universal joint bearing can cause a loss of steering control and increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect, and as necessary, replace the steering shaft, free of charge. Owner notification letters were mailed July 23, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021060001.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2018 CLA250 and CLA250 4MATIC, and 2017-2018 CLA45 AMG vehicles. The Occupant Classification System (OCS) may have been improperly calibrated, which may prevent the proper deployment of the front passenger air bag.
Risk and remedy
Risk
In the event of a crash, if the air bag does not deploy as designed, the front seat passenger has an increased risk of an injury.
Remedy
MBUSA will notify owners, and dealers will replace the passenger seat cushion, free of charge. The recall began July 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060012.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450…
Risk and remedy
Risk
If the starting current limiter overheats, the surrounding components can melt, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will install an additional fuse in the electrical line to the starter, free of charge. The recall began August 31, 2017. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2017080002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 CLA250, CLA250 4Matic, E400 Coupe, E400 4Matic Coupe, E550 Coupe, E400 Cabriolet, E550 Cabriolet, E300, E300 4Matic, E400 Wagon, GLA250, and GLA250 4Matic vehicles. The pelvis air bag or the front passenger air bag inflator initiator may fail to ignite in the event of a crash.
Risk and remedy
Risk
If the pelvis airbag or the front passenger airbag does not deploy as intended in the event of a crash, the occupants have an increased risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the affected air bag modules, free of charge. The recall began March 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
28 complaints2 involved a crash2 injuries
What owners report most
Latest complaints
- Lane departure › Warning · Unknown or other
The check engine light on the vehicle came on and remained on each time the vehicle is running. An independent service center in an effort to fix the problem, ran a diagnostic test and found that the check engine light is on due to two codes. (1) P052E-71 crankcase ventilation system has a…
The check engine light on the vehicle came on and remained on each time the vehicle is running. An independent service center in an effort to fix the problem, ran a diagnostic test and found that the check engine light is on due to two codes. (1) P052E-71 crankcase ventilation system has a malfunction (PCV has failed, needs tube assembly). (2) P06DA-00 oil pump solenoid circuit failure. Additionally, the independent service center found a Mercedes-Benz USA, LLC News Channel Update Warranty to Mercedes-Benz Dealer Principals, General Managers, Sales Managers, Service Managers, Parts Managers dated August 25, 2023 regarding Emission Extended Warranty - Intake Line Assembly. Specifically, the partial-load ventilation valve (a part of the intake line assembly} may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp ('MIL'). A faulty partial-load ventilation valve might also increase exhaust gas emission. MBUSA fault code associated with the vehicle extended warranty from 4 years/50,000 miles to 15 years/150,000 miles is: P052E71 - Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction. Damage code 0101D - Solenoid valve crankcase ventilation system. Part(s) code A274090560080 - Intake Line assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilation valve). And an ECU software update will be provided for certain vehicle variants. This vehicle's vin number is not included in the list for the extended warranty even as this vehicle is experience the same malfunctions described in the extended warranty enumerating the same necessary repairs the independent service center has recommended for this vehicle. The intent here is to add this vehicle's vin number to the many other vehicles within the same model years whose warranties have been extended to the 15 years/150,000 miles warranty, so that the repairs can be performed with warranty
- Electrical system
What component or system failed or malfunctioned, and is it available for inspection upon request? The instrument cluster display intermittently failed, either showing incorrect information or going completely blank while driving. Yes, the component is still installed in the vehicle and available…
What component or system failed or malfunctioned, and is it available for inspection upon request? The instrument cluster display intermittently failed, either showing incorrect information or going completely blank while driving. Yes, the component is still installed in the vehicle and available for inspection upon request. How was your safety or the safety of others put at risk? When the display failed, I was unable to view critical information such as vehicle speed, warning lights, and engine performance data. This posed a significant safety risk, especially while navigating traffic. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes, the issue was reproduced and confirmed by a independent service center. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? No Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? There were no warning lamps or error messages prior to the failure. The issue first appeared June 20, 2025 and began occurring intermittently before worsening over time.
- Power train
Component or System That Failed or Malfunctioned: The component that failed was the partial-load ventilation valve, which is part of the engine’s crankcase ventilation system. This valve is responsible for regulating airflow and pressure within the crankcase during partial engine loads. A…
Component or System That Failed or Malfunctioned: The component that failed was the partial-load ventilation valve, which is part of the engine’s crankcase ventilation system. This valve is responsible for regulating airflow and pressure within the crankcase during partial engine loads. A malfunction in this valve can lead to increased engine pressure, oil leaks, and potential damage to engine components. The component is still available for inspection upon request. Safety Risk: The failure of the partial-load ventilation valve put my safety, and that of others, at risk in the following ways: •Engine stalling or reduced power while driving, especially during acceleration, which increases the risk of an accident. •In some cases, oil leakage caused by excess crankcase pressure could lead to engine compartment smoke or a potential fire hazard. •If the engine performance is compromised, it may suddenly lose power on highways or intersections, posing a serious risk. Problem Reproduced or Confirmed: Yes, the issue was confirmed. The technician verified the faulty valve during a diagnostic inspection after I noticed performance issues and warning messages. Inspected by Manufacturer, Dealer, or Others: Yes, the vehicle was inspected Warning Lamps, Messages, or Other Symptoms: Yes, there were warning signs prior to the failure: •Check Engine Light illuminated on the dashboard. •Engine running rough or hesitating, particularly during acceleration.
- Engine · Fuel/propulsion system
Approximately 6 months I noticed my vehicle began to emit an odor and is not responsive immediately when I press on the gas. During this time period a yellow check engine light appeared on my dashboard. My local mechanic recommended Christopher Motors in Warwick Rhode Island and German Motors in…
Approximately 6 months I noticed my vehicle began to emit an odor and is not responsive immediately when I press on the gas. During this time period a yellow check engine light appeared on my dashboard. My local mechanic recommended Christopher Motors in Warwick Rhode Island and German Motors in Providence, Rhode Island, who specializes in Mercedes. I scheduled an appointment and took the vehicle to Christophers Motors to get a diagnostics check for $130. Christopher motors did a diagnostic check and revealed that the car needs a crank shift ventilator that will cost approximately $1500-$1800 and could not guarantee if the service engine light would be removed. During this time I received a Vehicle Registration Suspension notification for the State of RI for a failed safety inspection. I was extremely stressed receiving this notification as I recently purchased this vehicle, and I am being told by the State of RI my car is unsafe to drive and my transportation for work is being removed. I had to contact the State of RI and advised that no one will fix the safety check engine light problem and I need a time extension to contact the Mercedes Dealer. I then scheduled an appointment with Mercedes, Warwick RI and was told that the part for this repair was back ordered and that there is an extended warranty on this repair. (Exhibit A). This immediately put my mind at ease, and I could see a solution to this two-month long problem. Then I was informed that the extended warranty is only for 14 models all within the same year as my vehicle. The Dealership also advised that Mercedes may add the recall for the CLA 250 in the future and I would be reimbursed for the repair. I then contacted Mercedes of USA by letter requesting that my vehicle experiencing the same design errors on the crankcase ventilation system be included in their extended warranty. Unfortunately they would not add my vehicle to the extended warranty and did not provide a detailed explanation.
- Electrical system · Latches/locks/linkages › Trunk lid › Latch
1. What component or system failed or malfunctioned, and is it available for inspection upon request? The trunk latch system failed, causing the trunk to open unexpectedly. Yes, the component is available for inspection upon request. 2.How was your safety or the safety of others put at risk? The…
1. What component or system failed or malfunctioned, and is it available for inspection upon request? The trunk latch system failed, causing the trunk to open unexpectedly. Yes, the component is available for inspection upon request. 2.How was your safety or the safety of others put at risk? The trunk opened while driving on [XXX], creating a significant blind spot. This occurred during high traffic conditions and forced me to move to the outer lane, which posed a risk to my safety and the safety of other drivers on the road. 3.Has the problem been reproduced or confirmed by a dealer or independent service center? Yes, the problem has been reported by many other owners as well, suggesting a widespread issue. Additionally, Elite Bmers & Benz in Spring, Texas, inspected the car but could not immediately identify the problem. They need to conduct further research to determine the cause. 4.Has the vehicle or component been inspected by the manufacturer, police, insurance representatives, or others? The vehicle was inspected by Elite Bmers & Benz in Spring, Texas. However, the problem could not be pinpointed immediately, and further research is needed. It has not yet been inspected by the manufacturer, police, or insurance representatives. 5.Were there any warning lamps, messages, or other symptoms of the problem prior to the failure, and when did they first appear? There were no warning lamps, messages, or other symptoms prior to the trunk opening unexpectedly. The problem occurred without any prior indication. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Visibility › Sun/moon roof assembly
The contact owns a 2017 Mercedes-Benz CLA250. The contact stated while driving 60 MPH, the contact heard a loud pop inside the vehicle. The vehicle was steered to the side of the road and the contact observed that the sunroof panel was missing. A Police Officer passing by stated that he observed…
The contact owns a 2017 Mercedes-Benz CLA250. The contact stated while driving 60 MPH, the contact heard a loud pop inside the vehicle. The vehicle was steered to the side of the road and the contact observed that the sunroof panel was missing. A Police Officer passing by stated that he observed that the panel had detached and land on the street. The vehicle was taken to a dealer where it was diagnosed that the panel needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 90,000.
- Structure
The contact owns a 2017 Mercedes-Benz CLA250. The contact stated while driving 68-70 MPH, the front roof panel separated from the vehicle and flew off. The contact related the failure to NHTSA Campaign Numbers: 23V854000 (Structure) and 21V197000 (Structure). The dealer was notified of the failure…
The contact owns a 2017 Mercedes-Benz CLA250. The contact stated while driving 68-70 MPH, the front roof panel separated from the vehicle and flew off. The contact related the failure to NHTSA Campaign Numbers: 23V854000 (Structure) and 21V197000 (Structure). The dealer was notified of the failure and informed the contact that the VIN was not included. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 134,000.
- Power train · Unknown or other
Just replaced water pump and still need to replace positive Crankcase ventilation system hose
- Air bags
The airbag spontaneously deployed while driving. No impact with any other vehicle and no previous damage.
- Wheels
Wheel Rim cracks in normal driving conditions.
- Steering
Hello, My 2017 CLA Mercedes was recalled April 1 2021. They said its a hole in the steering shaft and it can lead to noises and crash! Its been over 3 months and the manufacturer has not fixed my car. Everytime I call they don't have an update on when it's going to be fixed. I have my family who I…
Hello, My 2017 CLA Mercedes was recalled April 1 2021. They said its a hole in the steering shaft and it can lead to noises and crash! Its been over 3 months and the manufacturer has not fixed my car. Everytime I call they don't have an update on when it's going to be fixed. I have my family who I drive around in this car and I'm worried the steering might cause harm to us. We need assistance in getting this resolved. Thanks
- Visibility › Sun/moon roof assembly
The contact owns a 2017 Mercedes-Benz CLA250. The contact stated that on two separate occasions while driving at various speeds, the panoramic sunroof detached from the vehicle without warning. The contact stated that the roof remained exposed with the wires from the sunroof hanging from the…
The contact owns a 2017 Mercedes-Benz CLA250. The contact stated that on two separate occasions while driving at various speeds, the panoramic sunroof detached from the vehicle without warning. The contact stated that the roof remained exposed with the wires from the sunroof hanging from the ceiling. The contact had taken the vehicle to the dealer twice where the replacement part for the sunroof were ordered. An independent glass technician repaired the panoramic sunroof however, the failure persisted. The manufacturer was notified of the failure by email however, there was no response. The vehicle was not yet repaired. The approximate failure mileage was 61,500.
- Structure › Body
The Panoramic Sunroof Glass front cover has detached three times from my 2017 CLA 250 (VIN#[XXX]). The first time that it detached was with the previous owner and was repaired at a Mercedes dealership in Tampa Florida. It has since detached twice with ME and I have only owned it for 12 months.…
The Panoramic Sunroof Glass front cover has detached three times from my 2017 CLA 250 (VIN#[XXX]). The first time that it detached was with the previous owner and was repaired at a Mercedes dealership in Tampa Florida. It has since detached twice with ME and I have only owned it for 12 months. The first time that it detached with me, I was driving approximately 60 MPH on I-85 in Montgomery. AL. It blew off and could have definitely caused a VERY SERIOUS accident, but luckily no vehicles were behind me at the time 4/29/21. So I went to the local Montgomery, AL. Mercedes dealership, Jack Ingram, and they said that there was No RECALL and there was nothing that they could do. So I had to purchase my own replacement glass from Mercedes and have an auto glass repair co. install it. Fast-forward to 6/18/21, the newly installed roof glass blew off again as I was driving down S.R. 115 in Montgomery, AL. I was going 55 at the time. This time it blew off and several cars had to swerve to miss it. One vehicle did run over it a broke it in two. Traffic has to stop while I jumped out and picked it up from the ROW. I guess MercedesBenz USA will make this right once it flies off for the 4th time and seriously injures someone or worse. Can someone PLEASE help me with this issue? [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
- Engine
Upon startup in cold weather...strong odor of gasoline can be noticed in passenger compartment. Internet search shows this to be a problem with the fuel line connected to the high pressure fuel pump.
- Electrical system · Engine and engine cooling · Equipment › Electrical › Infotainment › Video (touch)screen/monitor/unit
TL* the contact owns a 2017 mercedes-benz cla250. The contact stated that soon after having her oil changed, a coolant warning light illuminated on the instrument panel. The contact then took the vehicle to an independent mechanic where coolant was added. The contact also mentioned that the home…
TL* the contact owns a 2017 mercedes-benz cla250. The contact stated that soon after having her oil changed, a coolant warning light illuminated on the instrument panel. The contact then took the vehicle to an independent mechanic where coolant was added. The contact also mentioned that the home screen would go blank intermittently while driving at various speeds. Upon investigation, the contact linked the failure to nhtsa campaign number: 17v114000 (electrical system, engine and engine cooling) however, the vin was not included. Neither the manufacturer nor the dealer were notified of the failure. The vehicle was not repaired. The failure mileage was unknown.
- Air bags
TL* the contact owns a 2017 mercedes-benz C300. The contact stated while driving at an unknown speed, a vehicle unexpectedly made a left turn into the front drivers side of her vehicle causing it to accelerate and jump the curb eventually coming to a stop. the contact stated the air bags did not…
TL* the contact owns a 2017 mercedes-benz C300. The contact stated while driving at an unknown speed, a vehicle unexpectedly made a left turn into the front drivers side of her vehicle causing it to accelerate and jump the curb eventually coming to a stop. the contact stated the air bags did not deploy however an air bag malfunction warning alert illuminated. The front passenger tire and the whole driver side was damaged. The contact sustained four broken teeth, eye damage, traumatic brain injury, shoulder damage, seizures, and speech damage that required medical attention. a police report was filed. The vehicle was deemed undrivable however repairable by the insurance company as the air bags did not deploy. The contact stated that the dealer stated that the air bags were not defective. The manufacturer was made aware of the failure however, offered no assistance. The failure mileage was 20,000.
- Electrical system · Engine
TL* the contact owns a 2017 mercedes-benz cla250. While driving 30 mph, the vehicle jerked and stalled, but was able to restart. All the warning indicators were illuminated on the instrument panel. Additionally, the radio turned off on several occasions. The vehicle was towed to open road of…
TL* the contact owns a 2017 mercedes-benz cla250. While driving 30 mph, the vehicle jerked and stalled, but was able to restart. All the warning indicators were illuminated on the instrument panel. Additionally, the radio turned off on several occasions. The vehicle was towed to open road of bridgewater (1250 US-22 bridgewater, nj 08807, 908-213-5841) where it was diagnosed that the software needed to be updated and the battery needed replacement. The vehicle was repaired, but the failure recurred. The manufacturer was not contacted. The failure mileage was 40,458.*jb
- Power train
While making a u turn on fl-881 forest hills blvd , the half shaft failed, causing transmission to dis engage... While oncoming traffic was heading toward me. attached copy of maps.
- Power train
Making a u turn , on 3 lane blvd, a complete transmission failure happened and coasted to halt. Upon halt, transmission would not engage, drive or reverse. had there been heavy on coming traffic, I would have been t-boned currently the vehicle IS with dealership under repair and evaluation.
- Unknown or other
I was driving on the toll road when out of no where I here a loud boom and crackle above my head. Almost like a firework when it goes off. I thought it was a gun shot. When I looked up my panoramic sunroof was gone. Nothing was driving in front of or beside me. Nothing hit my car. However mercedes…
I was driving on the toll road when out of no where I here a loud boom and crackle above my head. Almost like a firework when it goes off. I thought it was a gun shot. When I looked up my panoramic sunroof was gone. Nothing was driving in front of or beside me. Nothing hit my car. However mercedes says it's impossible and something hit it, but my insurance won't pay for the sunroof repair because of class action lawsuits. They say it IS mercedes responsibility. However, mercedes basically called me a liar and refuses to replace the panoramic sunroof. They want to charge me $3200 to repair it.
- Air bags
TL* the contact owns a 2017 mercedes-benz cla250. The contact received notification of nhtsa campaign number: 17v627000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair as the recall…
TL* the contact owns a 2017 mercedes-benz cla250. The contact received notification of nhtsa campaign number: 17v627000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair as the recall notice was received over six months ago. The dealer (mercedes-benz of tacoma, 1701 alexander ave e c, fife, wa 98424) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was contacted several times and was unable to confirm when the parts were to become available. The contact had not experienced a failure. Vin tool confirms parts not available.
- Unknown or other · Visibility › Glass, side/rear
Rear window exploded after turning on rear defrost, vehicle was stationary when rear window exploded.
- Air bags
TL* the contact owns a 2017 mercedes-benz cla250. The contact received notification of nhtsa campaign number: 17v627000 (air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz…
TL* the contact owns a 2017 mercedes-benz cla250. The contact received notification of nhtsa campaign number: 17v627000 (air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of silver spring in silver spring, maryland was made aware of the recall and stated that the parts were unavailable. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Electrical system · Steering · Wheels
Sensor malfunctions, battery power loss with complete electrical shutdown, faulty wire harnesses, locked up steering wheel while in motion on freeway, head unit defaults, faulty tires with blistering, countless recalls.
- Air bags
TL* the contact leased a 2017 mercedes-benz cla250. The contact stated that the vehicle was included in nhtsa campaign number: 17v62700 (air bags). The contact stated that if the air bags deployed, it would cause injury to her family. The contact called a local dealer (mercedes-benz of palm beach…
TL* the contact leased a 2017 mercedes-benz cla250. The contact stated that the vehicle was included in nhtsa campaign number: 17v62700 (air bags). The contact stated that if the air bags deployed, it would cause injury to her family. The contact called a local dealer (mercedes-benz of palm beach, 400 okeechobee blvd, west palm beach, fl 33409) and was informed that the parts were not available. The vehicle was not diagnosed or repaired. The manufacturer was notified of the issue and informed the contact that the parts were not available. The contact had not experienced a failure. Vin tool confirms parts not available.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10246281Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205841Spare wheel.
- 10205257Model indicator index.
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205237The COMAND unit does not start or the display remains dark.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205218New roller blind with blind bearing does not fit in previous panoramic with old roof mechanisms or blind guide rails.
- 10205200Parktronic inoperable.
- 10205156Intial startup not possible after replacement of transmisson 725.0 or of electrohydraulic controller unit.
- 10205154Gasket may settle causing a slight oil leak.
- 10199675Vibrations/ humming when moving off or maneuvering with the wheels turned
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186132Humming/ vibrations/ noises from the area of the rear axle while maneuvering or when moving off
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179907Engine diagnosis warning lamp activated - Fault code P012800
- 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
- 10178737MBUX multimedia system: "Favorites" and "Recent destinations" not available
- 10178713Headlamps fogged
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10172683Information Label on Tire Sealant
- 10171637Retrofitted front door exit lamps with logo projection flicker
Every Mercedes-Benz CLA250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.