2018 Mercedes-Benz Cla 250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › Cla 250 › 2018
These records cover every 2018 Mercedes-Benz Cla 250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
9 recalls name the 2018 Mercedes-Benz Cla 250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2018 CLA250 and CLA250 4MATIC, and 2017-2018 CLA45 AMG vehicles. The Occupant Classification System (OCS) may have been improperly calibrated, which may prevent the proper deployment of the front passenger air bag.
Risk and remedy
Risk
In the event of a crash, if the air bag does not deploy as designed, the front seat passenger has an increased risk of an injury.
Remedy
MBUSA will notify owners, and dealers will replace the passenger seat cushion, free of charge. The recall began July 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060012.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2018 CLA250 and CLA250 4MATIC vehicles. The tail lights and the side marker lights may flicker or fail, affecting the vehicle's visibility.
Risk and remedy
Risk
Reduced visibility increases the risk of crash.
Remedy
MBUSA will notify owners, and dealers will replace the affected light bulb sockets, free of charge. The recall began April 5, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019030009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 Mercedes-Benz CLA250, CLA250 4Matic, and CLA45 AMG 4Matic vehicles. The Occupant Classification System (OCS) may not be properly calibrated, resulting in the front passenger air bag not being deactivated if a child seat is in the front seat.
Risk and remedy
Risk
If a child seat is in the front seat and the passenger air bag is not deactivated, in the event of a crash, it can increase the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the front passenger seat cushion, free of charge. The recall began January 2, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018120001.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Owner complaints
41 complaints2 involved a crash1 involved a fire2 injuries
What owners report most
Latest complaints
- Unknown or other
Roof Panel flew off on highway, not safe for anyone if this happens can cause accidents. It is available for inspection. This incident has happened to other cars of my same make and model and has been confirmed.
- Unknown or other
Panel flew off on the highway it was terrifying.
- Air bags
After a hard impact car continued to go then when came to a stop the air bags deployed which resulted in injuring my left arm
- Structure › Body
Water coming into the car through the floor
- Electrical system › Instrument cluster/panel
The instrument cluster gauges start giving in accurate information and the whole dash start turning on and off. I found hundreds of people posting complaints about this issue with the 2018 mercedes cla 250 but mercedes refuses to acknowledge this issue and put out a recall probably out of greed and…
The instrument cluster gauges start giving in accurate information and the whole dash start turning on and off. I found hundreds of people posting complaints about this issue with the 2018 mercedes cla 250 but mercedes refuses to acknowledge this issue and put out a recall probably out of greed and to not loose money. This is a dangerous issue. Mercedes wants to charge people appropriately $3,000 for parts and labor to fix this issue which is ridiculous. Please look into this. There needs to be a recall. This is dangerous especially for the people that cant afford this repair.
- Engine
Corrosion of the fuel system (on a Flex Fuel rated vehicle that had used E85 blend regularly) causing sudden loss of power, misfires, lack of acceleration The vehicle experience sudden loss of power, multiple misfires, and potential damage to the engine. Had the vehicle been on the highway or…
Corrosion of the fuel system (on a Flex Fuel rated vehicle that had used E85 blend regularly) causing sudden loss of power, misfires, lack of acceleration The vehicle experience sudden loss of power, multiple misfires, and potential damage to the engine. Had the vehicle been on the highway or attempting to merge with traffic this could have resulted in an accident See attached dealer diagnosis and replacement of multiple fuel injectors, fuel pump, and fuel rail. The dealer service manager stated (but did not document) that this was probably caused by using E85, despite the fact that the vehicle is rated for E85/flex fuel There were no warnings or indications prior to the incident
- Electrical system
I have sent the below email over 100 times to Mercedes To whom it may concern, I am writing regarding the purchase of a CLA250 4matic in December. I had a 120 point inspection done that did not show any issues with this car. As I was driving down a dark road around 1 am, my life was thrown in…
I have sent the below email over 100 times to Mercedes To whom it may concern, I am writing regarding the purchase of a CLA250 4matic in December. I had a 120 point inspection done that did not show any issues with this car. As I was driving down a dark road around 1 am, my life was thrown in danger as the command shaft shut off and I could not see the dashboard or any lights in the vehicle. I was alone and on a dark road. After sitting for 15 minutes, I was able to get a light to come on and drove to my destination. On my way home, the lights were acting erratic and the brake lights, bright lights, engine lights, gas gauge, rpm gauge and caution lights were flickering the entire time. The car had no problems starting, however this continued to happen. I parked the car for several days and after starting it again, the dashboard was black, I could not see to put it in park. I tried several days later and got the lights to come on and after driving through the light, the parking brake was thrown in place as I was driving, almost ejecting me from this vehicle. I immediately turned around and parked the car for over a week until bringing it to your service location at Atlanta South. The car put my life in danger, almost ejecting me out of the car. Thankfully I was not on the highway driving higher speeds or I would have been killed.. I am asking for Mercedes Benz to cover the entire amount for the command which I was told during service check was defective and wiring issues within the command. The cost is over $2,900. I believe this is a manufacturing defect whether you have any recalls on it or not. I will file a safety recall complaint with the NHTSA Nation vehicle recall for these vehicles of this make and model advising that you could be killed while driving this car without further recall. I have had other Mercedes benz vehicles and never had this problem. This is a matter of life or death. The car is currently parked at the dealer after inspection.
- Air bags
The contact owns a 2018 Mercedes-Benz CLA250. The contact stated that while driving and turning the steering wheel to the left, there was an abnormal clicking sound coming from the vehicle. Additionally, the electrical features on the steering wheel failed to operate as needed. The contact stated…
The contact owns a 2018 Mercedes-Benz CLA250. The contact stated that while driving and turning the steering wheel to the left, there was an abnormal clicking sound coming from the vehicle. Additionally, the electrical features on the steering wheel failed to operate as needed. The contact stated that several days later, the same failure returned with air bag and a "Front Left Malfunction - Service Required" message displayed on the instrument panel. The contact spoke to her mechanically inclined brother and was informed that the failure was likely related to a defective clock spring. Upon investigation, the contact discovered NHTSA Campaign Number: 17V627000 (Air Bags) ,which the contact linked to the failure. The contact went to the local dealer's website and communicated with an agent through the Live Chat feature. The contact was informed that the vehicle was not included in the recall. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
- Air bags
My clock spring is no longer working, it made all the buttons on my steering wheel stop working and i am afraid the airbag will deploy at random since there was a recall on cla models 2015-2018. I own a Mercedes cla 250 2018 but it is not showing a recall on my specific vehicle. Not only that but…
My clock spring is no longer working, it made all the buttons on my steering wheel stop working and i am afraid the airbag will deploy at random since there was a recall on cla models 2015-2018. I own a Mercedes cla 250 2018 but it is not showing a recall on my specific vehicle. Not only that but they no longer sell just the clock spring for my car, im assuming because of the recall. I am scared that my airbag will randomly deploy while im driving or that it will not deploy at all in case of an accident. It was diagnosed by an independent mechanic There was no other messages except when my left side airbag service needed message popped up
- Engine
P052E Check Engine light on. Same part is defective on other models that use the same parts. My car is not included in the recall.
- Electrical system
The panoramic sunroof opens and closes but will not shut completely in the back. When calling around for a quote mechanics were aware of the issue occurring with this specific make model and class of vehicle.
- Unknown or other
When you start off at a slow speed, the rear end of the car starts making a knocking noise. We had it inspected by Mercedes-Benz and they said that it is the rear differential.
- Fuel/propulsion system
Crank venting system. Wheel looses power. Oil us getting into sensors.
- Air bags · Steering
My car clock spring has went out, and it affects my car airbag deploy. I see it’s a problem with the Mercedes Cla250. It’s very dangerous it causes your horn not to work as well!
- Visibility › Sun/moon roof assembly
The contact owns a 2018 Mercedes-Benz CLA250. The contact stated that while the vehicle was parked, the sunroof switch was enabled to open the sunroof; however, the sunroof failed to open as intended. The contact stated that the left side of the sunroof did not open as intended. The vehicle was…
The contact owns a 2018 Mercedes-Benz CLA250. The contact stated that while the vehicle was parked, the sunroof switch was enabled to open the sunroof; however, the sunroof failed to open as intended. The contact stated that the left side of the sunroof did not open as intended. The vehicle was taken to the dealer where it was diagnosed with sunroof assembly failure. The contact was informed that the sunroof assembly needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was unknown. The VIN was unavailable.
- Structure › Body
Within 2 weeks after purchasing this vehicle the front stationary roof panel flew off the car. I noticed it when I parked at work in the parking lot. I do not know where the panel is. I retraced my route and did not see it anywhere. I work less than 2 miles from work with no turns. I am very…
Within 2 weeks after purchasing this vehicle the front stationary roof panel flew off the car. I noticed it when I parked at work in the parking lot. I do not know where the panel is. I retraced my route and did not see it anywhere. I work less than 2 miles from work with no turns. I am very concerned that the panel may cause water damage/leaking and even be a danger / damage to another drivers safety. I went to MB they said that there was no recall. They said that I should file claim to repair it. Claim and repair done be MB. NOW the same thing happened again. The panel has flown off again while I was driving on the highway around 3:00pm the panel nowhere to be found. MB said file a claim. 2 repair companies said the glue /sealant could be the issue. There were no notifications that this would happen. Pictures have been taken for both incidents. Upon referencing Vehicle Compliance & Analysis there is a recall Campaign Description: 23P2197658 NHTSA ID 23V854 I am having a difficult time getting my vehicle repaired without having to file another claim or paying for it myself.
- Structure
The contact owns a 2018 Mercedes-Benz CLA250. The contact stated that while the vehicle was at the car wash, water entered through the overhead center console. The vehicle was taken to the dealer, where it was determined that the front roof panel needed to be replaced and resealed. The vehicle was…
The contact owns a 2018 Mercedes-Benz CLA250. The contact stated that while the vehicle was at the car wash, water entered through the overhead center console. The vehicle was taken to the dealer, where it was determined that the front roof panel needed to be replaced and resealed. The vehicle was not repaired. The manufacturer was made aware of the failure but informed the contact that there was no recall associated with the VIN. The failure mileage was approximately 61,050.
- Seats · Structure › Body · Unknown or other
Water comes in the car and fills the back seat floors with water. I think its comming in from the frame.
- Engine
Check engine code PO52E - Positive Crankcase Ventilation regulator valve performance. Needs to be recalled
- Engine · Unknown or other
I am driving around 55K miles in this car, and my check engine light comes up. I head to a local place to get a code check. The guy looks it up and tells me this is pretty much with EVERY Mercedes CLA around that mile point.. So, I look up on reddit and other forums, and it's exactly what he said.…
I am driving around 55K miles in this car, and my check engine light comes up. I head to a local place to get a code check. The guy looks it up and tells me this is pretty much with EVERY Mercedes CLA around that mile point.. So, I look up on reddit and other forums, and it's exactly what he said. Pretty much the PCV valve is faulty and costs around $1800-2500 to fix after 50-60K miles which causes emission problems and other safety concerns if not taken care of. It makes no sense how this is not a recall. Of what I read, Mercedes knows all about this and has done nothing, just leaving the drivers to take care of a problem that they did nothing to cause. I am not sure if this is for the NHTSA or what, but it is kind of unacceptable.
- Power train
My 2018 Mercedes-Benz CLA250 4MATIC is experiencing a knocking noise from the rear differential at low speeds. The issue poses potential driving hazards, including possible loss of control and increased wear on drivetrain components. The noise may indicate a failing differential, which could…
My 2018 Mercedes-Benz CLA250 4MATIC is experiencing a knocking noise from the rear differential at low speeds. The issue poses potential driving hazards, including possible loss of control and increased wear on drivetrain components. The noise may indicate a failing differential, which could suddenly fail while driving. I have contacted the dealer, but no specific recalls or factory service announcements have been identified for this problem. This appears to be a common issue reported by other owners. At the recommendation of the service technician, I replaced the rear solenoid, at the cost of $400, but no improvement. A rebuild of the rear differential was the recommendation.
- Air bags
Air says it will malfunction nothing has happened but wish for it to be repaired before an accident
- Structure › Body
roof front panel coating peeling off - there has been a recall for this issue on most mercedes benz of my year - not just my model- seems to consistently be an issue for the front panel between windshield and sunroof- https://static.nhtsa.gov/odi/rcl/2021/RCMN-21V197-6244.pdf my specific VIN wasnt…
roof front panel coating peeling off - there has been a recall for this issue on most mercedes benz of my year - not just my model- seems to consistently be an issue for the front panel between windshield and sunroof- https://static.nhtsa.gov/odi/rcl/2021/RCMN-21V197-6244.pdf my specific VIN wasnt included in the recall but i am having the exact same issue- Mercedes told me to reach out to NHTSA to see about getting my VIN batch included in recall or re-issue broader recall to include my VIN # - they will not replace otherwise - so many people online have same issue as me and obviously it was enough of a hazard that the first recall was issued but there are more cars affected by it than what was covered.
- Electrical system · Lane departure › Assist · Lane departure › Warning
Vehicle cluster lights go black while driving...dangerous due to no fuel gauge..no speed gauge... no speedometor..no seat belt warning and no blinkers to exit highway safely....there is a danger of crashing as vehicles goes hesitant during black periods...this is an ongoing problem with Mercedes as…
Vehicle cluster lights go black while driving...dangerous due to no fuel gauge..no speed gauge... no speedometor..no seat belt warning and no blinkers to exit highway safely....there is a danger of crashing as vehicles goes hesitant during black periods...this is an ongoing problem with Mercedes as documented for numerous years with numerous vehicle's and different models. The safety of my driving this vehicle has come down to your ethics.. Does Mercedes value their customer [I think not] or does the safety of Highway Patrol ignore this dangerous and catastrophe accident waiting to happen.? I really hope someone will be helpful and I do really appreciate your time to this issue...
- Electrical system
The cluster panel lights that indicate speed, fuel, brakes, lights, turn signal, engine light, high beams and all other components of safety of car continue to black out altogether or flash on and off continuous while driving. Safety is an issue if your driving and cluster panel blacks out. You do…
The cluster panel lights that indicate speed, fuel, brakes, lights, turn signal, engine light, high beams and all other components of safety of car continue to black out altogether or flash on and off continuous while driving. Safety is an issue if your driving and cluster panel blacks out. You do not know the speed your driving at and no turn signals work. The problem was reported to Mercedes and the software was reset. The problem continues to happen while driving and is dangerous on highways as speedometer and turn signals do not work. Gas gage spins from full to empty and brake and engine lights flash on and off or cluster again goes black. There are or have never been warnings. While driving it just happens. This has been happening on and off for a few months. Mercedes does not know the cause.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10246281Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205841Spare wheel.
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205237The COMAND unit does not start or the display remains dark.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205218New roller blind with blind bearing does not fit in previous panoramic with old roof mechanisms or blind guide rails.
- 10205200Parktronic inoperable.
- 10205156Intial startup not possible after replacement of transmisson 725.0 or of electrohydraulic controller unit.
- 10205154Gasket may settle causing a slight oil leak.
- 10199675Vibrations/ humming when moving off or maneuvering with the wheels turned
- 10189400Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year 2018-2019 C and E-Class vehicles (205/238 platforms), an incorrect activated carbon filter might have been installed. In this case, the vehicle may not meet emission and certification requirements. MBUSA will conduct a voluntary Emission Recall Campaign in which an authorized Mercedes- Benz dealer will check the activated carbon filter, and replace it, if necessary.
- 10186132Humming/ vibrations/ noises from the area of the rear axle while maneuvering or when moving off
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179907Engine diagnosis warning lamp activated - Fault code P012800
- 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
- 10178737MBUX multimedia system: "Favorites" and "Recent destinations" not available
- 10178715Headlamps fogged
- 10178713Headlamps fogged
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10172683Information Label on Tire Sealant
- 10171637Retrofitted front door exit lamps with logo projection flicker
Every Mercedes-Benz Cla 250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.