2013 Mercedes-Benz ML350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › ML350 › 2013
These records cover every 2013 Mercedes-Benz ML350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2013 Mercedes-Benz ML350. Newest first.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…
Risk and remedy
Risk
An engine stall while driving increases the risk of a crash.
Remedy
Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…
Risk and remedy
Risk
The leaking oil in the presence of an ignition source can increase the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…
Risk and remedy
Risk
If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz is recalling certain accessory all-season floor mats sold for use in model year 2012 and 2013 Mercedes-Benz ML-Class vehicles. This all-season floor mat may not fully conform to the contour of the vehicle's floor plan as intended. Clearance between the mat and the gas pedal may be reduced, possibly allowing the pedal to become trapped.
Risk and remedy
Risk
This interference could prevent the gas pedal from retracting and the vehicle may not decelerate as expected when the driver lifts their foot from the gas pedal, which could increase the risk of a crash. Should the pedal become trapped, steady application of the brakes will allow the vehicle to be brought to a stop.
Remedy
Mercedes-Benz will notify owners, and dealers will replace the floor mats free of charge. Until replacement mats become available, consumers are advised to remove their floor mats from the vehicle. The safety recall began on December 21, 2012. Only vehicles equipped with the accessory floor mats are affected. Owners may contact Mercedes-Benz for more information at 1-800-367-6372.
Owner complaints
57 complaints2 involved a crash3 involved a fire3 injuries
What owners report most
Latest complaints
- Engine · Fuel/propulsion system
Vehicle: 2013 Mercedes-Benz ML350 BlueTEC (OM642 3.0L V6 Turbo Diesel) Current Mileage: Approx. 117,925 miles Dealer / Location: Mercedes-Benz of North Scottsdale (RO #260467) Summary of Safety Issue & Defect: The vehicle is experiencing an active liquid diesel fuel leak from a replacement fuel…
Vehicle: 2013 Mercedes-Benz ML350 BlueTEC (OM642 3.0L V6 Turbo Diesel) Current Mileage: Approx. 117,925 miles Dealer / Location: Mercedes-Benz of North Scottsdale (RO #260467) Summary of Safety Issue & Defect: The vehicle is experiencing an active liquid diesel fuel leak from a replacement fuel pump assembly that was previously installed by an authorized Mercedes-Benz dealership four years ago. Active diesel leaks directly over/near hot engine and exhaust components pose an acute, severe vehicle fire hazard and expose cabin occupants to toxic diesel fumes. Additionally, the vehicle exhibits a severe oil leak in the engine inner-V caused by prematurely degraded factory oil cooler seals (addressed in Mercedes TSB LI18.30-P-055434), along with an active DEF reductant heater circuit fault (DTC P20BD). The dealership confirmed the fuel leak but refused to rectify or honor Goodwill coverage for the prematurely failing fuel pump, presenting a repair quote exceeding $14,000. Active fuel component leaks present an unreasonable safety risk to vehicle occupants and surrounding traffic.
- Electrical system · Engine · Fuel/propulsion system
NHTSA VEHICLE SAFETY COMPLAINT SUPPORTING STATEMENT Vehicle: 2013 Mercedes-Benz ML350 I am submitting this complaint regarding a continuing safety concern involving water intrusion and electronic system damage in my 2013 Mercedes-Benz ML350. My vehicle was subject to a Mercedes-Benz recall…
NHTSA VEHICLE SAFETY COMPLAINT SUPPORTING STATEMENT Vehicle: 2013 Mercedes-Benz ML350 I am submitting this complaint regarding a continuing safety concern involving water intrusion and electronic system damage in my 2013 Mercedes-Benz ML350. My vehicle was subject to a Mercedes-Benz recall involving water intrusion and related components. Despite recall-related repairs being performed, moisture and water intrusion concerns remain unresolved. During the diagnostic process, Mercedes-Benz personnel identified evidence of water and humidity in areas associated with vehicle electronics and control modules. The vehicle has experienced repeated mechanical and electronic issues following discovery of the water intrusion condition. Multiple repair facilities have been involved, and I have incurred significant diagnostic and repair expenses while attempting to determine the full extent of the damage. The primary concern is not ordinary wear and tear. The concern is that water intrusion has affected vehicle systems and that the recall remedy has not resulted in a complete resolution of the condition. I am concerned that moisture exposure may continue to impact vehicle electronics, control modules, sensors, and other safety-related systems. Mercedes-Benz USA has been notified and a case has been opened. The dealership has also been involved. However, despite escalation requests and requests for management review, I have not received a meaningful resolution. The dealership continues directing me back to Mercedes-Benz USA while Mercedes-Benz USA has not provided a final management response. I respectfully request that NHTSA review whether the recall remedy adequately addressed the water intrusion condition and whether additional investigation is warranted regarding continuing moisture intrusion, electronic system exposure, and potential safety risks associated with this condition. I am prepared to provide repair orders, recall documentation, photographs, diagnostic findin
- Fuel/propulsion system
Re: My 2013 ML350- Intermittent Start/ Vehicle cutting off while in heavy traffic. Fuel Pump and Fuel modulator failed due to water collecting in the spare tire wheel-weld causing water intrusion into the fuel system. I paid out of pocket for this service twice, AND then found out from MB Tacoma…
Re: My 2013 ML350- Intermittent Start/ Vehicle cutting off while in heavy traffic. Fuel Pump and Fuel modulator failed due to water collecting in the spare tire wheel-weld causing water intrusion into the fuel system. I paid out of pocket for this service twice, AND then found out from MB Tacoma there was a RECALL with the exact same issue. I took the vehicle in to the closest dealer- Seattle Mercedes to handle the outstanding recall issues. I was advised to contact MERCEDES BENZ USA GOODWILL DEPARTMENT. My initial claim was approved, as I submitted ALL DOCUMENTATION of the repairs related to this issue. NOW, after 5 months of my RECALL REIMBURSEMENT CLAIM BEING BOUNCED AROUND by customer service agents that were not trained to handle recall issues- my dealership needed approval to process it. I even provided MB-USA w/a Bulletin # (FROM MB-USA) that clearly states to claim reimbursement IF THESE PARTS FAILED AND THE CUSTOMER PAID OUT OF POCKET.
- Engine · Fuel system, gasoline › Delivery › Fuel pump
The contact owns a 2013 Mercedes-Benz ML350. The contact stated that while driving approximately 40 - 45 MPH, the vehicle stalled in the middle lane. The driver was able to push the vehicle safely to the roadside. There were no warning lights illuminated. The vehicle was towed to the local dealer…
The contact owns a 2013 Mercedes-Benz ML350. The contact stated that while driving approximately 40 - 45 MPH, the vehicle stalled in the middle lane. The driver was able to push the vehicle safely to the roadside. There were no warning lights illuminated. The vehicle was towed to the local dealer, where it was diagnosed, and determined that the fuel pump needed to be replaced. The vehicle was repaired. The following day, it took two minutes to start the vehicle. The vehicle was drivable, but the vehicle eventually stalled while driving. The vehicle was towed to another local dealer, Mercedes-Benz of South Orlando (4301 Millenia Blvd, Orlando, FL 32839), where it was diagnosed with a faulty fuel sensor and control valve. The parts were replaced. The contact stated that the fuel pump was replaced four times, but the failure persisted. The manufacturer was contacted and escalated the failure was escalated to an engineer for assistance. The failure mileage was approximately 96,000.
- Electrical system · Fuel/propulsion system
Good morning ! I am an owner of a 2013 ML 350 . I live in San Diego ,CA ,92103 . I was driving my car on [XXX] and it was raining a lot . After around 30 miles I got to my destination parking area and my car died 20 feet away from the parking zone .I tried to reignite it but it wouldn’t start .…
Good morning ! I am an owner of a 2013 ML 350 . I live in San Diego ,CA ,92103 . I was driving my car on [XXX] and it was raining a lot . After around 30 miles I got to my destination parking area and my car died 20 feet away from the parking zone .I tried to reignite it but it wouldn’t start . I checked it with a OBD2 scanner and it was indicating a code U0109 - Lost communication with fuel pump control module . After looking into solutions and reasons for the issue online I came across a post regarding an existing recall with NHTSA with ID 22v955 regarding water intrusion in the spare wheel well portion of the trunk( The Wheel well is not water proofed and doesn’t have a drain port for water to escape ) . I proceeded with inspecting the area and of course it was full of water . The fuel pump control module is located in that area and it was damaged which shorted it and cause the malfunction of the vechile and the error code U0109 stated above . Tried calling Mercedes Benz but they confirmed about that specific recall but said my VIN is not part of it and I should file a claim or complain with you . I will attach proof and pictures of the water and the damaged component. My car now need to be towed and fixed on my expense because of Mercedes Benz negligence… Hopefully you can add my car to this recall and when this happens I would get some kind of reimbursement… Thank you for your time and understanding. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine
The engine locked up after blowing the top part of the engine off, fire shot out of the engine and quickly went out like a flam thrower. I was driving on the expressway when the accelerator would not work without any warning I didn’t have any issues with this truck. The car cut off immediately…
The engine locked up after blowing the top part of the engine off, fire shot out of the engine and quickly went out like a flam thrower. I was driving on the expressway when the accelerator would not work without any warning I didn’t have any issues with this truck. The car cut off immediately thank God I was able to coast to the side of the expressway because it stopped in the left lane on the expressway I was scared for our lives. The dealership has the truck and they said the engine is locked up. This morning s unacceptable for a car I’ve had for a year.
- Service brakes
Brake Booster failure, this vehicle is exhibiting the EXACT same symptoms as described in Recall Campaign: Campaign No. 2024050001, May 2024 TO: ALL MERCEDES-BENZ CENTERS SUBJECT: Model GL-Class, ML-Class, and R-Class (X164, W164 and 251 platform) Model Year 2006 – 2012 Inspect Brake Booster –…
Brake Booster failure, this vehicle is exhibiting the EXACT same symptoms as described in Recall Campaign: Campaign No. 2024050001, May 2024 TO: ALL MERCEDES-BENZ CENTERS SUBJECT: Model GL-Class, ML-Class, and R-Class (X164, W164 and 251 platform) Model Year 2006 – 2012 Inspect Brake Booster – without Pedal Rework Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2006-2012 ML-Class, GL-Class, and R-Class (164 and 251 platform) vehicles, the function of the brake booster might be affected due to advanced corrosion in the joint area of its housing. After extended time in the field and in conjunction with prolonged water exposure, this corrosion might lead to a vacuum leak at the brake booster. Loss of braking power puts me and everyone I am near while operating this vehicle in eminent danger!! This problem has been inspected and documented by Mercedes Benz of Macon Ga. 9-3-25 There were no warning lamps or messages present.
- Fuel/propulsion system
Fuel system failed carbon and shut off without any notification while driving two times put me at risk of getting hit both times as the vehicle was not in a safe spot. This has been confirmed at the dealership where my vehicle is at this point. It has been inspected by the dealership in Georgetown…
Fuel system failed carbon and shut off without any notification while driving two times put me at risk of getting hit both times as the vehicle was not in a safe spot. This has been confirmed at the dealership where my vehicle is at this point. It has been inspected by the dealership in Georgetown, Texas. Again, no warning lights just cut off two times while driving. I already had one recall fixed two times dealing with the fuel system and now it’s shutting off with no notice while I’m driving 60 70 mph and causing a dangerous safety hazard. Dealer stated… pressure regulator and control valve field as it is designed to maintain and regulate the amount fuel flowing into the engine.
- Fuel/propulsion system · Unknown or other
On [XXX], while driving on the highway about 30 miles from Columbus, Ohio my 2013 Mercedez Benz ML350 suddenly stalled and lost power. There was no prior warning. Luckily, we were in the outer lane with no car close behind us so my husband slowly guided the car to the side road. The car has since…
On [XXX], while driving on the highway about 30 miles from Columbus, Ohio my 2013 Mercedez Benz ML350 suddenly stalled and lost power. There was no prior warning. Luckily, we were in the outer lane with no car close behind us so my husband slowly guided the car to the side road. The car has since been towed and is currently at the Service Department at Mercedez Benz of North Olmsted, Ohio, 44070, for repairs. I have been informed by the Service Manager that they have identified the fuel pump to the problem and that it needs to be replaced. Coincidentally, this vehicle went for Maintenance Servicing at the same dealership and was returned to me on Monday December 16th. No problem with the fuel pump was identified or reported to me. This vehicle is available for inspection About 4 years ago, the exact same incident happened with this same vehicle where it suddenly stalled and completely lost power on the highway in the middle of nowhere on our way from Ohio to Iowa. There was no prior warning. Similarly, the car was towed to Mercedez Benz North Olmsted but per the same service manager their inspection revealed no problem and the car restarted on its own so nothing needed to be fixed. I am reporting this recurring problem with my vehicle because of the obvious safety risk of sudden stalling and power loss on the highway, the fact that 4 years ago when this happened Mercedez Benz should have recognized what the issue was and replaced the fuel pump but did nothing about it, and also due to the fact that many Mercedez Benz vehicles have experienced this same problem leading to multiple recalls including many 2013 ML 350s. I believe my vehicle has a defective fuel pump from the manufacturer just like the recalled vehicles and that my vehicle and many more need to be recalled INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Structure
The contact owns a 2013 Mercedes-Benz ML350. The contact stated that there was water on the floor below the front driver’s side. No warning lights were illuminated. The vehicle was towed to a local dealer because the battery was drained. The contact stated that while the vehicle was placed onto the…
The contact owns a 2013 Mercedes-Benz ML350. The contact stated that there was water on the floor below the front driver’s side. No warning lights were illuminated. The vehicle was towed to a local dealer because the battery was drained. The contact stated that while the vehicle was placed onto the tow truck, the contact and the hauler noticed that the vehicle continued to leak water. The contact advised the dealer that after the battery was replaced, the contact asked that the location of the leak be sought. The contact received the vehicle with the battery replaced; however, contact was informed that a diagnostic test was needed. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 74,000.
- Service brakes, hydraulic
The contact owns a 2013 Mercedes-Benz ML350. The contact stated while driving approximately 35 MPH as the contact depressed the brake pedal, he felt that the brake pedal was soft and he had to depress the pedal with more force to stop. No warning light was illuminated. The contact had taken the…
The contact owns a 2013 Mercedes-Benz ML350. The contact stated while driving approximately 35 MPH as the contact depressed the brake pedal, he felt that the brake pedal was soft and he had to depress the pedal with more force to stop. No warning light was illuminated. The contact had taken the vehicle to an independent mechanic where it was diagnosed and determined that the brake booster needed to be replaced. The vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 199,000.
- Engine
The contact owns a 2013 Mercedes-Benz ML350. The contact stated while adding washer fluid to the vehicle, the contact became aware that there was oil leaking from the upper timing chain covers down onto the alternator. The vehicle was taken to an independent mechanic, where it was determined that…
The contact owns a 2013 Mercedes-Benz ML350. The contact stated while adding washer fluid to the vehicle, the contact became aware that there was oil leaking from the upper timing chain covers down onto the alternator. The vehicle was taken to an independent mechanic, where it was determined that the upper timing chain covers needed to be removed and resealed. Additionally, the mechanic informed the contact that the oil needed to be cleaned off the engine and the alternator. The contact stated that upon investigating the failure, the contact became aware that the upper timing chain cover coating material did not allow the cover to seal properly. The vehicle was taken to the dealer to be repaired. The vehicle was repaired. The manufacturer was notified of the failure and a case was opened. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 66,000.
- Electrical system · Lane departure › Blind spot detection
Started to have an issue with the blind spot assist showing inoperable. Shortly after depending on the outside temperature the AC would start shutting off and on. The days the temperature was above 95 degrees the AC would suddenly stop working. Took the vehicle to the dealer for AC service. Dealer…
Started to have an issue with the blind spot assist showing inoperable. Shortly after depending on the outside temperature the AC would start shutting off and on. The days the temperature was above 95 degrees the AC would suddenly stop working. Took the vehicle to the dealer for AC service. Dealer reports the engine "back" wiring harness had been rubbing, exposing and chaffing the harness wires, and for safety concerns a complete harness replacement is necessary. When asked how was this possible since the harness clearance is a manufacture design. Was told it happens on these vehicles and currently there is no recall.
- Power train
The contact owns a 2013 Mercedes-Benz ML350. The contact stated while driving 20-25 MPH, the transmission shifted from second to third gear and was slipping. The contact stated that the transmission had previously been replaced; however, the failure recurred. The vehicle was taken to an independent…
The contact owns a 2013 Mercedes-Benz ML350. The contact stated while driving 20-25 MPH, the transmission shifted from second to third gear and was slipping. The contact stated that the transmission had previously been replaced; however, the failure recurred. The vehicle was taken to an independent mechanic, who diagnosed that there was water intrusion into the transmission and determined that the transmission coolant line, radiator, transmission, and transmission cooler needed to be replaced. The vehicle was not yet repaired and remained at the dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 136,000.
- Forward collision avoidance › Adaptive cruise control · Forward collision avoidance › Automatic emergency braking · Lane departure › Blind spot detection
Both the front distronic system,which controls adaptive cruise control and emergency braking, and the blind spot warning have failed. Failure of both systems is usually caused by water getting into the respective control units related to poor sealing allowing water to enter and causing the systems…
Both the front distronic system,which controls adaptive cruise control and emergency braking, and the blind spot warning have failed. Failure of both systems is usually caused by water getting into the respective control units related to poor sealing allowing water to enter and causing the systems to fail. I believe that these systems are critical to vehicle safety. The pre safe braking is essential to the safe operation of the vehicle. Blind spot warning failure is also a safety item on vehicles like these with large blind spot areas. Dealer has been no help other than repairs costing almost as much as the vehicle is worth. Very poor design and unsafe when these critical systems fail.
- Steering
Power Steering Motor snapped from the casing while driving. Seems like a defective casting.
- Service brakes
What component or system failed or malfunctioned, and is it available for inspection upon request? - Brake How was your safety or the safety of others put at risk? - Car didn't stop upon pressing on the brake pedel. Has the problem been reproduced or confirmed by a dealer or independent service…
What component or system failed or malfunctioned, and is it available for inspection upon request? - Brake How was your safety or the safety of others put at risk? - Car didn't stop upon pressing on the brake pedel. Has the problem been reproduced or confirmed by a dealer or independent service center? - Yes Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? -UNKNOWN Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? -No
- Unknown or other
I stopped to get gas at a club store & left on a full tank. Right after leaving the pump I pulled aside in the parking lot to get situated and after turning on the heater I began to drive away and then I started smelling something weird about the same time I noticed a thin cloud of white smoke and…
I stopped to get gas at a club store & left on a full tank. Right after leaving the pump I pulled aside in the parking lot to get situated and after turning on the heater I began to drive away and then I started smelling something weird about the same time I noticed a thin cloud of white smoke and I was looking around to see where it was coming from and then I saw more smoke coming up from behind my glove box and then I was looking for a place to move my car away from others and parked it, turned it off and dialed 911. My car my 2013 mercedes benz ML 350 started burning up less than 30 minutes after school drop off!!!! there was no warning light or warning beeping sound. Nothing! Just smoke and fire. This just happened 5 days ago and no inspection as yet but my auto insurance company was notified. I could have died. thank god I was not on the freeway.
- Electrical system
Turn signals stop working after driving a mile or so. If possible, I turn the car off and on. Turn signals work but fail again within a few miles. Hazard light work even when the turn signals fail. I’ve read this is a common issue searching the internet. Definitely a safety concern
- Lane departure › Blind spot detection
Blind spot inoperative message appeared while driving. Upon doing diagnosis with OBDII tester a fault was found with the left rear radar unit. There seem to be many social media accounts of these units failing due to water intrusion from apparently poor or defective water sealing. This may cause…
Blind spot inoperative message appeared while driving. Upon doing diagnosis with OBDII tester a fault was found with the left rear radar unit. There seem to be many social media accounts of these units failing due to water intrusion from apparently poor or defective water sealing. This may cause lane intrusion accidents due drivers being accustomed to the warning system working and notifying them of a vehicle in the blind spot. 2013 Mercedes Benz ML350 4Matic. Thank you for your consideration. Fault verified by OBDII tester. Vehicle not yet involved in an accident. Fault message was intermittent for several weeks before finally constant, Blind Spot Inoperative message stayed on.
- Service brakes
The brake booster failed while driving and I almost got in an accident. The brakes did not fully work and started pulsating almost like if the antilock system engaged. The brake booster was leaking air around the piston that attaches to the brake pedal. You could hear the air leaking when the pedal…
The brake booster failed while driving and I almost got in an accident. The brakes did not fully work and started pulsating almost like if the antilock system engaged. The brake booster was leaking air around the piston that attaches to the brake pedal. You could hear the air leaking when the pedal was pressed. It has been repaired at he MB dealer for about $2300. There were no indications of a malfunction, no lights or errors showed up.
- Suspension
The contact owns a 2013 Mercedes-Benz ML350. The contact stated that after starting the vehicle and shifting into drive(D), the vehicle would not accelerate above 15 MPH. The contact stated that the accelerator pedal was depressed; however, the vehicle failed to exceed 15 MPH. The contact pulled…
The contact owns a 2013 Mercedes-Benz ML350. The contact stated that after starting the vehicle and shifting into drive(D), the vehicle would not accelerate above 15 MPH. The contact stated that the accelerator pedal was depressed; however, the vehicle failed to exceed 15 MPH. The contact pulled over, stopped, turned off, and restarted the vehicle and was able to resume normal driving. The contact stated that the traction control warning light was illuminated. The contact stated that the failure was intermittent at first but became a recurring failure. The contact had taken the vehicle to a local dealer, who diagnosed and determined that oil had leaked from the reservoir oil cap onto the alternator and damaged the alternator. The vehicle had not been repaired. The manufacturer had been informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 18V272000 (Suspension). The failure mileage was approximately 125,000.
- Air bags
The contact owned a 2013 Mercedes Benz ML350. The contact stated that the vehicle was stopped waiting for traffic to pass when a second vehicle suddenly crashed into the front end of the vehicle. During the crash, the front end of the vehicle was severely damaged and the vehicle was destroyed but…
The contact owned a 2013 Mercedes Benz ML350. The contact stated that the vehicle was stopped waiting for traffic to pass when a second vehicle suddenly crashed into the front end of the vehicle. During the crash, the front end of the vehicle was severely damaged and the vehicle was destroyed but no airbags were deployed. No injuries were reported. A police report was taken at the scene and the vehicle was towed away. The cause of the failure was not yet determined. The manufacturer and local dealer were not yet notified of the incident. The failure mileage was 96,000.
- Unknown or other
2013 ml350 strong moldy smell in car when air conditioner IS running, change air /cabin filter several times smell stop for a whle and then come back. Check for water or leaking found nothing. If I good to the mercedes this going to cost me a lot of money for them look or to find the problem.
- Electrical system · Engine
2013 Mercedes Benz ML350 (W166) engine (m276) began misfiring. Palm Springs Mercedes Benz diagnosed faulty camshaft positioning sensor leaking engine oil into engine electrical harness which wicked through harness to ECU. Faulty (leaking) camshaft positioning sensor caused faulty harness, ECU, injectors, o2 sensors. Said common problem on these and other models and engines.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10219253Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) vehicles listed below, the particulate matter (PM) sensor could potentially fail and consequently activate the malfunction indicator light (MIL) with one of the fault codes mentioned below. As a result, the warranty for the PM sensor has been extended from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 10 years / 120,000 miles (whichever occurs first).
- 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10186144Armrest In Center Console (Front) Only Opens On One Side Or Not At All - Model Series 167
- 10184799Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10181195Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain MercedesBenz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or cause to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed. An authorized Mercedes-Benz dealer will install the AEM at a later date at no cost to the Owner/Lessee.
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167577Since 12/2012 (model 166) and since 06/2013 (model 242) the glass breakage loops are no longer in the side windows and rear window. Suitable interior protection ensures that the interior monitoring function continues to operate correctly.
- 10167565A flapping/rattling noise can be heard from the area of the center console towards the rear.
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167553Combination message: "Clean fuel filter" is displayed. The fault code 162500 (water level message - Bosch) or P226997 (water level message - Delphi) or 171600 (filter load - Bosch) is stored in the engine control unit.
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167549Thumping noises at the front axle when driving over road bumps
- 101675481. In vehicles up to VIN 166 ### #A 097760 without code 803, the following fault code is logged in the quick test: P1C9B00. The control unit 'Roll control' has a malfunction. 2. In vehicles up to VIN 166 ### #A 097760 with code 803 or vehicles as of VIN 166 ### #A 097761, the following fault code is logged in the quick test: P1C9564. The rotation direction valve of the torsion bar ''Front axle'' has a malfunction.
Every Mercedes-Benz ML350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.