2014 Mercedes-Benz ML350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › ML350 › 2014
These records cover every 2014 Mercedes-Benz ML350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2014 Mercedes-Benz ML350. Newest first.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…
Risk and remedy
Risk
An engine stall while driving increases the risk of a crash.
Remedy
Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…
Risk and remedy
Risk
The leaking oil in the presence of an ignition source can increase the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…
Risk and remedy
Risk
If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
68 complaints7 involved a crash2 involved a fire3 injuries
What owners report most
Latest complaints
- Exterior lighting
Turn signals stop functioning during drive cycles. This functionality is lost for the remainder of the current drive cycle and can be restored with a key cycle. It does not occur every drive cycles and is unpredictable.
- Visibility › Sun/moon roof assembly
The contact owns a 2014 MERCEDES-BENZ E350. The contact stated while driving 60 MPH on the freeway, there was a popping noise coming from the sunroof and discovered it was shattered. The vehicle was not taken to the dealer or an independent mechanic for diganoses .The vehicle was not repaired The manufacturer was not notified of the failure. The approximate failure mileage was 108,000 .
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2014 Mercedes-Benz ML350. The contact stated that while driving at 35 MPH and accelerating above 40 MPH, the vehicle failed to accelerate above 40 MPH before it lost automotive power. The vehicle was driven back to the residence. The vehicle was diagnosed by the dealer, and the…
The contact owns a 2014 Mercedes-Benz ML350. The contact stated that while driving at 35 MPH and accelerating above 40 MPH, the vehicle failed to accelerate above 40 MPH before it lost automotive power. The vehicle was driven back to the residence. The vehicle was diagnosed by the dealer, and the failure was associated with NHTSA Campaign Number: 22V955000 (FUEL SYSTEM, DIESEL, FUEL SYSTEM, GASOLINE); however, the VIN was not associated with the recall repair. The vehicle was repaired out of pocket. The manufacturer was notified of the failure. The failure mileage was 115,000.
- Unknown or other
Today at 1/27/25 630 pm my vehicle caught fire.i was told that the vehicle was subject to the Active Curve System (Recall 18V272) and Fuel Pump (Recall 23V010).
- Service brakes
It seems that this vehicle was not included in a brake booster recall which included this model from 2005 through 2015. The brakes are not working properly, and brake fluid has entered the master brake cylinder damaging the seal. It is extremely unsafe to operate this vehicle in this condition. Somehow, this vehicle was not included in the recall, but definitely should have been.
- Fuel/propulsion system
As we were driving 50mph, the car stalled and lost all power. The dashboard lights all lit up and the car wouldn't start. I don't get unnerved easily and it was fairly intense not being able to move your car out of traffic. After about 5 mins, the car would start again only to stop a minute or so…
As we were driving 50mph, the car stalled and lost all power. The dashboard lights all lit up and the car wouldn't start. I don't get unnerved easily and it was fairly intense not being able to move your car out of traffic. After about 5 mins, the car would start again only to stop a minute or so later. After taking the car to the dealer, the issue stemmed from the fuel pump electronics board getting wet in the spare tire wheel well where water was accumulating. This was part of the recall and the dealer installed a drain and replaced the board. HOWEVER, this issue again happened nearly one year later in our next rainy season. After taking it to the dealer, they said WE would need to replace the electronics board ourselves. We asked about the recall and they said they fixed the issue by installing the drain plug and there was nothing else they could do for us. Even the service adjuster was upset and very sympathetic to our plight as the car was obviously not fixed. Even though the drain plug was installed, the water was still acumulating in the wheel well. It seems apparent to me, and several others who have complained about the same issue, that the recall fix has not addressed the main issue of why the water is coming in and why it's still not draining. Unfortunately we're going to have to fork over $1200 to have it fixed. My ask to the NHTSA is that this issue be readdressed with Mercedes. I would like them to be notified that the recall does not address the underlying issues and the solution they provided does not fix the problem. I appreciate your time in considering this.
- Electrical system · Lane departure › Blind spot detection
Vehicle: 2014 Mercedes-Benz ML350 VIN: [XXX] I have experienced repeated failures of the Blind Spot Assist / driver-assist system since purchasing this vehicle. When I first purchased the ML350 in Texas, the vehicle already showed warning messages (“Blind Spot Assist Inoperative / Pre-Safe…
Vehicle: 2014 Mercedes-Benz ML350 VIN: [XXX] I have experienced repeated failures of the Blind Spot Assist / driver-assist system since purchasing this vehicle. When I first purchased the ML350 in Texas, the vehicle already showed warning messages (“Blind Spot Assist Inoperative / Pre-Safe Function Limited”). The dealer attempted repairs before delivery, but the defect persisted. After moving to New York, the problem continued. On June 26, 2023, I took the vehicle to The Automaster Mercedes-Benz in Shelburne, VT. Their diagnosis confirmed water intrusion into the blind spot radar sensors, consistent with Mercedes-Benz TSB LI54.71-P-056477. Both left and right sensors and wiring require replacement. This is a safety defect because Blind Spot Assist and Pre-Safe features are disabled without warning, increasing risk of collision when changing lanes. Many other owners have reported the same issue, and Mercedes has issued a TSB acknowledging the defect, but no recall has been provided. I request that NHTSA investigate this recurring safety problem and require Mercedes-Benz to provide coverage or a recall for affected vehicles. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Air bags
Driver side airbag malfunction without notice .serious bodily injury incase of an accident.
- Lane departure › Blind spot detection
The contact owns a 2014 Mercedes-Benz ML350. The contact stated that upon starting the vehicle, the blind spot warning light illuminated. The contact was unable to identify if another vehicle was nearby. The vehicle was taken to an independent mechanic who determined that the blind spot detection…
The contact owns a 2014 Mercedes-Benz ML350. The contact stated that upon starting the vehicle, the blind spot warning light illuminated. The contact was unable to identify if another vehicle was nearby. The vehicle was taken to an independent mechanic who determined that the blind spot detection system was inoperative. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 170,001.
- Electrical system · Engine · Lane departure › Blind spot detection
I purchased a used Mercedes-Benz from Freehold Mitsubishi in early 2024. Within hours, serious safety issues appeared, including a check engine light, cylinder misfire, EVAP leak, traction control failure, and blind spot assist malfunction. The vehicle’s ECM and wiring harness were later found…
I purchased a used Mercedes-Benz from Freehold Mitsubishi in early 2024. Within hours, serious safety issues appeared, including a check engine light, cylinder misfire, EVAP leak, traction control failure, and blind spot assist malfunction. The vehicle’s ECM and wiring harness were later found damaged due to oil leaks and electrical shorts. Despite multiple repair attempts, the vehicle was returned in worse condition and remains unsafe to drive. I am reporting these issues due to their potential risk to vehicle safety.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2014 Mercedes-Benz ML350. The contact stated while the vehicle was idling in the driveway, the vehicle stalled. The contact stated that AAA added fuel to the vehicle, and the vehicle was able to restart and operated as needed. The contact stated that the vehicle was taken to the…
The contact owns a 2014 Mercedes-Benz ML350. The contact stated while the vehicle was idling in the driveway, the vehicle stalled. The contact stated that AAA added fuel to the vehicle, and the vehicle was able to restart and operated as needed. The contact stated that the vehicle was taken to the dealer for the recall repair of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline), and the dealer installed a water drain plug on the vehicle. The contact stated that the check engine warning light was later intermittently illuminated. The vehicle was taken to Complete Performance, where it was diagnosed with fuel pressure failure. The contact replaced the gas cap; however, the failure persisted. Additionally, the contact stated while driving 45 MPH, the vehicle stalled while there was sufficient fuel in the fuel tank. The contact was able to pull over to the side of the road. The vehicle was able to restart after fuel was added to the vehicle. An unknown dealer was notified of the failure and informed the contact that the fuel pump was not previously replaced during the recall repair of NHTSA Campaign Number: 22V955000( Fuel System, Diesel, Fuel System, Gasoline). The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 60,000.
- Electrical system · Engine · Fuel/propulsion system
I purchased my car used at the Mercedes dealership in Tyler Texas June 2023. I took all my savings and paid cash and was told that the car was impeccable shape and there were no current issues and all the service records were up to date. November 2023 is when everything started happening and my…
I purchased my car used at the Mercedes dealership in Tyler Texas June 2023. I took all my savings and paid cash and was told that the car was impeccable shape and there were no current issues and all the service records were up to date. November 2023 is when everything started happening and my engine light came on. It was revealed to me by a service tech that I was sold the vehicle with an existing major oil leak /seals broke. Etc. SEE Attached invoices. I have endured driving down the road and my car just giving out and losing power steering. The car has been sputtering and there have been misfires, fauled fuel injectors, coils, s and spark plugs, oil leaks, fuel pump leaking gasoline in the engine and smoke coming from the hood. I thought my car was going to start on fire it smelled like a hot electrical wires and gasoline. My nerves are frayed from this car because of how many times it has broke down. I have missed work because of the car, I'm behind on my home bills, I missed my airline flight to see my sick father, I have had to pay for rental cars, all due to this vehicle. I am very concerned for my safety in this vehicle and I would like the vehicle fixed at the expense of Mercedes or my money back. Thank you, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Tires
I purchased four brand new "GoodYear" tires with this location in February 2024. Within two months of this purchase, I experienced two flat tires in which both times I had to pay $87 and some change. Addtionally, within a year, two of the tires became bald, indicating premature wear. Tragically…
I purchased four brand new "GoodYear" tires with this location in February 2024. Within two months of this purchase, I experienced two flat tires in which both times I had to pay $87 and some change. Addtionally, within a year, two of the tires became bald, indicating premature wear. Tragically, this month, the bald tires contributed to a car accident, resulting in damages of my vehicle and loss of time from work. This incident has caused significant distress and has raised serious concerns about the quality of the tires and the services provided from this location. I have attempted to resolve this matter directly with the service center and cooperate office. To this day, no adequate response has been addressed to resolve my concerns. I'm glad to live to be able to tell my story and advocate for others!!! Tire Size 255/50R19`
- Electrical system · Fuel/propulsion system
ML350 engine stalled while driving on an expressway and would not turn back on. ML350 needed to be towed where it was determined that water accumulated in the spare tire wheel well, leading to the fuel pump short circuiting. This is directly related to NHTSA campaign 22V955000. That recall repair…
ML350 engine stalled while driving on an expressway and would not turn back on. ML350 needed to be towed where it was determined that water accumulated in the spare tire wheel well, leading to the fuel pump short circuiting. This is directly related to NHTSA campaign 22V955000. That recall repair was completed prior to this incident. Per the technician, the recall repair installed a water drain plug to prevent the water accumulation. This repair effectively failed - the drain plugs malfunctioned and were not allowing water to drain. MBUSA deny’s responsibility for the failing drain plug - stating that the trunk weatherstripping is the root cause, not the failing drain plug. This is an unacceptable response and worth of the recall being expanded. The fuel pump control unit can still short out if MBUSA’s poor excuse of a recall fix fails as it did with mine.
- Electrical system › Instrument cluster/panel
See attached document for complaint
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2014 Mercedes-Benz ML350. The contact had received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The vehicle was taken to a dealer and the recall repair was performed. Soon after the recall repair, while the contact's wife was…
The contact owns a 2014 Mercedes-Benz ML350. The contact had received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The vehicle was taken to a dealer and the recall repair was performed. Soon after the recall repair, while the contact's wife was driving 25 MPH, the vehicle stalled. The contact was unaware if any warning lights had illuminated during the failure. The vehicle was towed to an independent mechanic where it was discovered that there was moisture in the spare tire wheel well. The moisture damaged the fuel pump control unit which was linked to the recall. The contact attempted to reach the manufacturer but was unsuccessful. The vehicle was taken back to the dealer but was not repaired and remained in dealer possession. The failure mileage was unknown.
- Engine · Fuel/propulsion system · Unknown or other
I bought my vehicle into Mercedes Benz for a recall related to water collection in spare tire well which can cause a fuel pump control malfunction, NHTSA recall # 22V955. A few days ago, my vehicle could not start and I found water in my spare tire well. My OBD scanner tells me it is related to the…
I bought my vehicle into Mercedes Benz for a recall related to water collection in spare tire well which can cause a fuel pump control malfunction, NHTSA recall # 22V955. A few days ago, my vehicle could not start and I found water in my spare tire well. My OBD scanner tells me it is related to the fuel pump. I informed Mercedes Benz and they would not fix it. Obviously the work performed did not correct the recall. I'm writing here hoping I can get connected to the right channel to get this resolved as my vehicle is currently unusable. Thanks.
- Electrical system · Engine · Power train
Blind spot assists and turn signals go out without warning. This model should have been included in the previous recall for timing. Having the same issues as other recalled cars.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2014 Mercedes-Benz ML350. The contact stated while driving at various speeds, the vehicle hesitated while accelerating and sometimes sputtered before accelerating. The contact stated that there was water inside the spare tire wheel well. The vehicle was taken to the local dealer…
The contact owns a 2014 Mercedes-Benz ML350. The contact stated while driving at various speeds, the vehicle hesitated while accelerating and sometimes sputtered before accelerating. The contact stated that there was water inside the spare tire wheel well. The vehicle was taken to the local dealer to be repaired under NHTSA Campaign Number: 22V955000 (Fuel System, Gasoline, Fuel System, Diesel). During the recall repair the water drainage plug was installed but the fuel pump was not replaced even though the vehicle had experienced the failure listed in the recall. The manufacturer was notified of the issue but no assistance was offered. The failure mileage was 185,000.
- Seats
Traveling on my way home from Arizona and as my back was hurting turned on heated seats…I also had air conditioning running due to dogs in back seat…I started noticing what felt like a pinching sensation where my butt and legs meet…Stopped thr car at next rest area and noticed butt really hurt when…
Traveling on my way home from Arizona and as my back was hurting turned on heated seats…I also had air conditioning running due to dogs in back seat…I started noticing what felt like a pinching sensation where my butt and legs meet…Stopped thr car at next rest area and noticed butt really hurt when I slid out of car…felt back there and area and hurt like heck..got into my Rv that a friend was driving and looked at it!! 2nd degree blisters/burns from heated seats!! I thought “what the heck?”as I didn’t have any marks on the seat!! Clearly the temperature spiked and causes the burns!’ I looked it up and see that MB has had a long history of this…and major litigation. But no recall!! I have pictures!! (But for obvious reasons can’t send here) I had a miserable ride home and the pain continues! It is embarrassing but I want to make sure other unsuspecting people don’t have this happen! Plus, I want it fixed…!
- Electrical system · Engine · Unknown or other
I am writing in regards to my 2014 ML 350 Suv. The check engine light came on and upon taking it to the mercedes dealership, I was told the issue is that the camshaft adjusters have failed and need to be replaced. The cost quoted is over $11,000 to repair. Upon further investigation I found…
I am writing in regards to my 2014 ML 350 Suv. The check engine light came on and upon taking it to the mercedes dealership, I was told the issue is that the camshaft adjusters have failed and need to be replaced. The cost quoted is over $11,000 to repair. Upon further investigation I found reports on multiple lawsuits for the Mercedes C series for the same year (2012-2014) that resulted also in a recall whereby customers were given a recall to replace at no charge the camshaft adjusters up to 120k miles. My car only has 83k and I am told by two independent mechanics that the camshaft adjuster should not be failing like this and that this has been an ongoing issue with Mercedes. The safety issue is that I am told by independent mechanics that what could happen over time is that I could be driving and the entire engine/power just shuts off. This could even happen at high speeds on the highway. The mercedes dealer tells me there is no safety issues that could result from camshaft adjuster problems which doesn't appear to be true as per the other independent mechanics. I request further investigation into this issue because as per the independent mechanics its the "same engine" as the 2012-2014 that are under the recall . I'm requesting a recall on this for my car that Mercedes pays for. This should not be failing especially in a car with only 83k on it . If the C series 2012-2014 received recall on this part then I also think my ML 350 should be covered. Mercedes customer service tells me they cannot pay for the repair, they said I could file complaint for recall through NHTSA Thank you .
- Electrical system · Engine
Known defect with timing issues that give code P0016. All cars should be part of this recall regardless of mileage on a known defect. This repair is extremely expensive and wouldn’t be needed if built correctly.
- Structure › Body
Power Sun ROOF is coming off the tracks of the roof which it is attach to. I feel this is an extreme safety hazard because I believe it will eventually come off my vehicle and cause a serious accident flying into another vehicle or even a pedestrian. This was fixed by Mercedes Benz [ BENZE…
Power Sun ROOF is coming off the tracks of the roof which it is attach to. I feel this is an extreme safety hazard because I believe it will eventually come off my vehicle and cause a serious accident flying into another vehicle or even a pedestrian. This was fixed by Mercedes Benz [ BENZE BUSCH of NJ ] back in to 2018 and now it is doing it again.I Contacted the dealer again about this and they refuse to repair saying Vehicle is out of warranty.I also contacted Mercedes Benz corporate Headquarters and they refuse to acknowledge the problem.Obviously this is a defect in the vehicle. I researched that they have had similar problems with other vehicles SUN ROOF problems and they acknowledge those facts and repaired them. I previously filed a complaint with the NHTSA ID #11478665 but it seems that you didn't have all the facts. Please look into this matter again now that you do. Thank YOU
- Electrical system
The contact owns a 2014 Mercedes-Benz ML350. The contact stated that while at a stop light, the vehicle lost motive and electric power and stalled without warning. The contact restarted the vehicle, but the vehicle failed to remain running. The vehicle was towed to an independent mechanic and the…
The contact owns a 2014 Mercedes-Benz ML350. The contact stated that while at a stop light, the vehicle lost motive and electric power and stalled without warning. The contact restarted the vehicle, but the vehicle failed to remain running. The vehicle was towed to an independent mechanic and the contact was informed that water had intruded into the rear of the vehicle causing electrical failures. The vehicle was not repaired because the Insurance Company deemed the vehicle a total loss. The manufacturer was contacted but offered no assistance. The failure mileage was 60,000. The contact stated that the interior of the vehicle has to be dried out first in order to assess the damage to the electrical system. The contact noted the failure mileage was 60379.
- Unknown or other
Unknown
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10219253Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) vehicles listed below, the particulate matter (PM) sensor could potentially fail and consequently activate the malfunction indicator light (MIL) with one of the fault codes mentioned below. As a result, the warranty for the PM sensor has been extended from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 10 years / 120,000 miles (whichever occurs first).
- 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10186144Armrest In Center Console (Front) Only Opens On One Side Or Not At All - Model Series 167
- 10184799Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10181195Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain MercedesBenz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or cause to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed. An authorized Mercedes-Benz dealer will install the AEM at a later date at no cost to the Owner/Lessee.
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167577Since 12/2012 (model 166) and since 06/2013 (model 242) the glass breakage loops are no longer in the side windows and rear window. Suitable interior protection ensures that the interior monitoring function continues to operate correctly.
- 10167565A flapping/rattling noise can be heard from the area of the center console towards the rear.
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167553Combination message: "Clean fuel filter" is displayed. The fault code 162500 (water level message - Bosch) or P226997 (water level message - Delphi) or 171600 (filter load - Bosch) is stored in the engine control unit.
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167549Thumping noises at the front axle when driving over road bumps
- 101675481. In vehicles up to VIN 166 ### #A 097760 without code 803, the following fault code is logged in the quick test: P1C9B00. The control unit 'Roll control' has a malfunction. 2. In vehicles up to VIN 166 ### #A 097760 with code 803 or vehicles as of VIN 166 ### #A 097761, the following fault code is logged in the quick test: P1C9564. The rotation direction valve of the torsion bar ''Front axle'' has a malfunction.
Every Mercedes-Benz ML350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.