2015 Mercedes-Benz ML350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › ML350 › 2015
These records cover every 2015 Mercedes-Benz ML350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2015 Mercedes-Benz ML350. Newest first.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…
Risk and remedy
Risk
An engine stall while driving increases the risk of a crash.
Remedy
Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…
Risk and remedy
Risk
The leaking oil in the presence of an ignition source can increase the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2015 GL350 4Matic Blutec, GL450 4Matic, GL550 4Matic, ML250 Blutec, ML350, ML350 4Matic, ML400 4Matic and 2015-2016 GL63 AMG 4Matic vehicles manufactured September 29, 2014 through March 27, 2015. The affected vehicles have axle bolts on the front and/or rear drive axle carriers that may not…
Risk and remedy
Risk
If any of the remaining front or rear axle bolts fracture, the vehicle may be unstable, reducing the handling capability and increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the axle carrier bolts, free of charge. The recall is began February 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2015 ML250, ML350, ML350 4Matic, ML400 4Matic, ML63 AMG, and 2016 GLE450 AMG 4Matic vehicles manufactured from April 27, 2015, through May 19, 2015. The affected vehicles may have had the right rear seatbelt anchor bolt incorrectly installed.
Risk and remedy
Risk
In the event of a vehicle crash, the right rear seatbelt anchor bolt could fail to secure the passenger, increasing their risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect and, if necessary, correct the installation of the right rear seat belt anchor bolt, free of charge. The recall began on July 22, 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
52 complaints10 involved a crash4 injuries
What owners report most
Latest complaints
- Fuel/propulsion system
The failed/malfunctioning component appears to be the fuel pump controller / fuel pump control unit, and possibly the fuel pump system. The Mercedes-Benz dealer identified water/moisture-related damage and corrosion at the fuel pump controller area. The failed component should be available for…
The failed/malfunctioning component appears to be the fuel pump controller / fuel pump control unit, and possibly the fuel pump system. The Mercedes-Benz dealer identified water/moisture-related damage and corrosion at the fuel pump controller area. The failed component should be available for inspection if the dealer preserves the part during repair. I have requested that the dealer not discard the damaged component. My safety and the safety of others were put at risk because the fuel pump controller is related to fuel delivery. If it fails, the vehicle may not start, may lose fuel supply, or may stall while driving. This creates a safety risk, especially if the vehicle stalls in traffic, at an intersection, on a highway, or during normal driving. The problem has been confirmed by a Mercedes-Benz dealership. The dealership diagnosed water/moisture damage to the fuel pump controller area and provided an estimate of $768.22 for fuel pump controller replacement, plus $244.88 for the inspection fee. The dealer also indicated that this was the first inspection and that the fuel pump itself may also need further inspection or may have related damage. The vehicle/component has been inspected by a Mercedes-Benz dealership. Mercedes-Benz USA / the manufacturer’s representative has also reviewed the case through its goodwill process, but they refused to treat it as recall-related coverage. To my knowledge, the vehicle has not been inspected by police or insurance representatives. Prior to the current failure, the vehicle had starting/no-start related symptoms beginning around the middle of 2023. The engine could not start successfully at times. I do not recall receiving a clear warning lamp or message specifically identifying the fuel pump controller before the failure. However, the symptoms were consistent with a fuel delivery problem, and the dealer later confirmed water/moisture corrosion damage in the fuel pump controller area.
- Unknown or other
In July 2025, the sunroof panel had lifes and was flapping at highway speeds. I immediately contacted a Mercedes-Benz dealer to report the hazard. I was told they were unaware of such an issue and that I would have to pay for the repair out-of-pocket. Due to financial hardship, I could not afford…
In July 2025, the sunroof panel had lifes and was flapping at highway speeds. I immediately contacted a Mercedes-Benz dealer to report the hazard. I was told they were unaware of such an issue and that I would have to pay for the repair out-of-pocket. Due to financial hardship, I could not afford the repair at that time. in. In early February, while driving on the highway, the entire sunroof panel catastrophically detached and flew off the vehicle. This created an immediate and severe road hazard for other drivers. This incident matches the 'adhesive bonding failure' described in other Mercedes-Benz sunroof recalls (e.g., Recall 21V-197), but my specific VIN was not included in that list.
- Electrical system · Exterior lighting · Lane departure › Blind spot detection
In mid-trip as we were going down the highway went to change lanes and the turn signals were no longer functioning. No errors, no alerts, no warnings they just stopped working. After pulling over and turning off the vehicle and turning back on they work for a time then stop working again. After…
In mid-trip as we were going down the highway went to change lanes and the turn signals were no longer functioning. No errors, no alerts, no warnings they just stopped working. After pulling over and turning off the vehicle and turning back on they work for a time then stop working again. After researching with other owners of these and similar model Mercedes Benz vehicles this is a prevalent and highly dangerous safety issue that many many others have experienced.
- Engine
Cam Shaft replacement diagnosed after week and half visit to Mercedes Benz dealership for engine rattling at cold start up. We are left with a $10,000 repair after performing all scheduled maintenance at the Mercedes Benz dealership since owning in 2015.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2015 Mercedes-Benz ML350. The contact stated that while driving at various speeds, the vehicle shook abnormally before the vehicle lost automotive power. The contact was able to restart the vehicle and take the vehicle to a local dealer. The contact stated that the vehicle was…
The contact owns a 2015 Mercedes-Benz ML350. The contact stated that while driving at various speeds, the vehicle shook abnormally before the vehicle lost automotive power. The contact was able to restart the vehicle and take the vehicle to a local dealer. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline); however, the repair failed to prevent the failure. The contact stated that two weeks after the recall repair, the failure reoccurred. The check engine warning light was illuminated. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The vehicle was scanned by a local independent mechanic who retrieved DTC: P035413, A10D, P072102, U016886, V1FBD04, 94C3, V1DAV54, V1DBD31, P030085, and V142E31. The manufacturer was made aware of the failure. The failure mileage was approximately 88,000.
- Service brakes
I was in drive mode and was looking to park the car on the open spot on the street. Had engaged the reverse gear and was attempting to get in the parallel parking spot. While i was doing that, suddenly the wheel locked up and car stopped with a jerk/jolt. Then came warning that the parking brake…
I was in drive mode and was looking to park the car on the open spot on the street. Had engaged the reverse gear and was attempting to get in the parallel parking spot. While i was doing that, suddenly the wheel locked up and car stopped with a jerk/jolt. Then came warning that the parking brake was not working (Remember I had not engaged the parking brake as I was in drive mode). The locked up wheel would not move and I had great difficulty in making the car safe in the cross traffic. The issue here is parking brake cannot engage by itself. That has nothing to do with the age of the car, it is like the wheel cannot come off just because the car is old. This could have easily happened while the car was in motion at a higher speed, in that case with 1 wheel locked, a car would spin out of control in a moving traffic causing major damage to other vehicles and myself. Mercedes's rep claimed it was a maintenance item. Parking brake engaging by itself is a maintenance item?? We should put a notice to all customers and your life is in danger because the parking brake can engage by itself locking the wheel anywhere anytime. I am very apprehensive of this design which allows for auto lock of a wheel. It must be investigated and all the parking brake systems should be replaced as it can happen to anyone. Thank you
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2015 Mercedes-Benz ML350. The contact stated while reversing, the vehicle stalled and failed to restart. The vehicle was towed to the local mechanic who determined that the fuel pump was faulty and needed to be replaced. The fuel pump was replaced, and the vehicle was repaired.…
The contact owns a 2015 Mercedes-Benz ML350. The contact stated while reversing, the vehicle stalled and failed to restart. The vehicle was towed to the local mechanic who determined that the fuel pump was faulty and needed to be replaced. The fuel pump was replaced, and the vehicle was repaired. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The contact was informed that the VIN was included in NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 120,000.
- Unknown or other
The center console box will jot close. I have researched and this is a common problem with this car. You can not just replace the closure part it requires a whole new box. This is at a cost of 400.00plus dollars. This is obviously a defect.
- Engine
precense of some liquik oil from up motor litle meiby ist because change oil because i buy recently , i need observed ,ore time today i clean this area.
- Latches/locks/linkages › Doors › Latch
The contact owns a 2015 Mercedes Benz ML350. The contact stated that the rear driver’s side door failed to close properly after several attempts. The vehicle was taken to a dealer and the contact asked the mechanic to inspect the vehicle. The door failed to open after several attempts. The contact…
The contact owns a 2015 Mercedes Benz ML350. The contact stated that the rear driver’s side door failed to close properly after several attempts. The vehicle was taken to a dealer and the contact asked the mechanic to inspect the vehicle. The door failed to open after several attempts. The contact was provided an estimate for the repair. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 58,000.
- Power train
The contact owns a 2015 Mercedes-Benz ML350. The contact stated while reversing, there was an abnormal sound coming from the vehicle. No warning light was illuminated. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure and determined that the VIN was not included in a recall. The failure mileage was unknown.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2015 Mercedes-Benz ML350. The contact stated while driving at undisclosed speeds, the vehicle temporarily lost motive power before returning to normal driving functionality. There was no warning light illuminated. The vehicle was taken to a dealer and the contact was informed…
The contact owns a 2015 Mercedes-Benz ML350. The contact stated while driving at undisclosed speeds, the vehicle temporarily lost motive power before returning to normal driving functionality. There was no warning light illuminated. The vehicle was taken to a dealer and the contact was informed that the check engine light displayed after repairing the vehicle under NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline). The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 79,000.
- Suspension
In April 2023, while performing a rear brake service both right and left suspension springs were found with deteriorated suspension spring coating, corrosion and breakage of the coil springs. Suspension spring failure poses a safety hazard and risk of damage to other suspension components. It is…
In April 2023, while performing a rear brake service both right and left suspension springs were found with deteriorated suspension spring coating, corrosion and breakage of the coil springs. Suspension spring failure poses a safety hazard and risk of damage to other suspension components. It is unclear when exactly the springs broke but when the vehicle was inspected in Feb of 2022 there was no mention of spring breakage. The date of incident is the date I discovered the spring breaks. I only took a pic of the one spring but both were confirmed broken. MB dealership confirmed breakage. Communication with Mercedes Benz was not successful.
- Fuel system, diesel · Fuel system, gasoline
The contact owns a 2015 Mercedes-Benz ML350. The contact received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of…
The contact owns a 2015 Mercedes-Benz ML350. The contact received notification of NHTSA Campaign Number: 22V955000 (Fuel System, Diesel, Fuel System, Gasoline) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated while driving approximately 40 MPH, the vehicle started to lose motive power and was making an abnormal sputtering sound as if the vehicle was running out of gasoline. The contact stated that the vehicle stalled with the check engine warning light illuminated. The contact pulled over and was able restart the vehicle. The failure had become a recurring failure. The manufacturer had not been made aware of the failure. The failure mileage was approximately 104,000. Parts distribution disconnect.
- Engine
Engine stalled multiple times even though it has been serviced multiple times at multiple dealers.
- Engine
I took my car in for a different repair and they found this issue as well. "Diagnostic - Oil leak (Visual): front covers leaking oil down front of engine." The leak was due to a crack in the sealing cap. My car 2015 Mercedes ML350 4Matic is in the recall for 2018070015 but my VIN number was not…
I took my car in for a different repair and they found this issue as well. "Diagnostic - Oil leak (Visual): front covers leaking oil down front of engine." The leak was due to a crack in the sealing cap. My car 2015 Mercedes ML350 4Matic is in the recall for 2018070015 but my VIN number was not included in the recall although I am having the exact issues the recall covers. Recall 2018070015 "correct oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out."
- Engine · Fuel/propulsion system · Unknown or other
There is a recall for this significant safety risk. I contacted my local Mercedes Benz about recall remedy on 6 January 2023 and they confirmed the recall and said MB would issue steps to get this taken care of in the beginning of February. It is now 18 February 2023 and this has not happened and I have received no communication from MB and yet the safety risk still exists and could be life threatening.
- Engine · Fuel/propulsion system · Unknown or other
My viechle is loss of propulsion without warning on the freeway last week on a raining day. After brought the car to West Covina Dealer inspected the car is leaking water that has entered the spare wheel well, the accumulated water could intermittently contact the fuel pump control unit caused…
My viechle is loss of propulsion without warning on the freeway last week on a raining day. After brought the car to West Covina Dealer inspected the car is leaking water that has entered the spare wheel well, the accumulated water could intermittently contact the fuel pump control unit caused loss propulsion. And there are some circuit boards and wires damaged due to a water leak and not drive able. The West Covina MB dealer is refuse to fix until MBusa responsible for the cost. Please help what other option we have about this issue?
- Steering
Steering wheel tilt adjustment failed. Without adjustment it is impossible to steer the automobile safely due to hand placement for control. This is apparent especially when there are multiple drivers. There is not a manual over ride since the system is controled electrically
- Engine · Engine and engine cooling
The contact owns a 2015 Mercedes-Benz ML350. The contact stated while driving at an undisclosed speed, the engine seized without warning. The vehicle was towed to the local dealer where it was diagnosed there was a possible mechanical break down due to engine sludge, ignition varnish rust…
The contact owns a 2015 Mercedes-Benz ML350. The contact stated while driving at an undisclosed speed, the engine seized without warning. The vehicle was towed to the local dealer where it was diagnosed there was a possible mechanical break down due to engine sludge, ignition varnish rust, corrosion, dust, cracked rubber, dry rot, road chemicals, alterations or improper oil, coolant, fuel, or lubricants. The vehicle was not repaired. The manufacturer was not contacted. The approximate failure mileage was 70,273. The contact stated that they did not submit this complaint and the vehicle actually belongs to another individual.
- Air bags
takata airbags- call Mercedes Benz of Draper says it is not on their list????
- Structure › Body
Neither back doors on my 2015 ML350 lock. Even after you try to lock them from the inside anyone can open the doors from the outside. This is a huge safety hazard because someone could easily car jack the car while you are in it. I bought the car new from the local dealer and i have reported this…
Neither back doors on my 2015 ML350 lock. Even after you try to lock them from the inside anyone can open the doors from the outside. This is a huge safety hazard because someone could easily car jack the car while you are in it. I bought the car new from the local dealer and i have reported this to the dealership and they said it was a known problem and that acutuators on both doors needed to be replaced at a large cost to me. I wrote to Mercedes Corporate to report this and to ask for financial assistance in trying to get it corrected and was told to just report it to you. Thank you for any assistance that you can provide.
- Suspension
The contact owns a 2015 Mercedes-Benz ML350. The contact stated that while the vehicle was parked in the driveway, she noticed an unknown fluid leaking from the vehicle. Over time, the contact noticed that an unknown pink fluid had also started to leak form the vehicle. On one occasion while…
The contact owns a 2015 Mercedes-Benz ML350. The contact stated that while the vehicle was parked in the driveway, she noticed an unknown fluid leaking from the vehicle. Over time, the contact noticed that an unknown pink fluid had also started to leak form the vehicle. On one occasion while driving 25 MPH, the vehicle started to hesitate with an abnormal popping sound coming from the vehicle. The contact stated that dark blue smoke was coming from the vehicle. The vehicle eventually stalled without warning. The vehicle failed to restart for almost an hour. The vehicle eventually restarted after multiple attempts and was driven back to the residence. The following day, the vehicle was towed to the dealer where they discovered that water was leaking into the exhaust and had caused the failure. Upon investigation, the contact discovered NHTSA Campaign Number: 18V272000 (Suspension) which she linked to the failure. The manufacturer was notified of the failure and the contact was informed that the VIN was not under recall. The vehicle was not repaired. The failure mileage was unknown.
- Seat belts
The contact owns a 2015 Mercedes-Benz ML350. The contact stated that while the vehicle was parked and attempting to seat the child in the car seat, he noticed that the seat belt was loose. The contact checked the car seat and pushed the seat to one side and the seat belt unwound and retracted to…
The contact owns a 2015 Mercedes-Benz ML350. The contact stated that while the vehicle was parked and attempting to seat the child in the car seat, he noticed that the seat belt was loose. The contact checked the car seat and pushed the seat to one side and the seat belt unwound and retracted to the normal position. The contact had taken the vehicle to a local dealer who diagnosed that the seat belt latching system had failed and needed to be replaced. The vehicle was not repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 105,000.
- Air bags
The contact owned a 2015 Mercedes-Benz ML350. The contact stated that while driving approximately 40-45 mph in the rain, he drove over a puddle of water and hydroplaned on the highway and hit the jersey wall, went across the highway, and crashed into the guard rail. The air bags did not deploy.…
The contact owned a 2015 Mercedes-Benz ML350. The contact stated that while driving approximately 40-45 mph in the rain, he drove over a puddle of water and hydroplaned on the highway and hit the jersey wall, went across the highway, and crashed into the guard rail. The air bags did not deploy. There were no warning indicator lights illuminated. The contact sustained injuries to his shoulder and medical attention was provided. The passenger occupant sustained injuries to the vertebrae and medical attention was provided. A police report was filed. There was no reported fire. The vehicle was towed to an independent lot. The local dealer was contacted but the vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 120,000. The vehicle was deemed a total loss by the insurance company.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10186144Armrest In Center Console (Front) Only Opens On One Side Or Not At All - Model Series 167
- 10184799Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10181195Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain MercedesBenz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or cause to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed. An authorized Mercedes-Benz dealer will install the AEM at a later date at no cost to the Owner/Lessee.
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167577Since 12/2012 (model 166) and since 06/2013 (model 242) the glass breakage loops are no longer in the side windows and rear window. Suitable interior protection ensures that the interior monitoring function continues to operate correctly.
- 10167565A flapping/rattling noise can be heard from the area of the center console towards the rear.
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167553Combination message: "Clean fuel filter" is displayed. The fault code 162500 (water level message - Bosch) or P226997 (water level message - Delphi) or 171600 (filter load - Bosch) is stored in the engine control unit.
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167549Thumping noises at the front axle when driving over road bumps
Every Mercedes-Benz ML350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.