2007 MINI Cooper
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › MINI › Cooper › 2007
These records cover every 2007 MINI Cooper. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2007 MINI Cooper. Newest first.
BMW of North America, LLC (BMW) is recalling certain 2008-2014 MINI Clubman Cooper, Clubman Cooper S, Clubman John Cooper Works, and 2007-2013 MINI Hardtop 2-Door Cooper, Cooper S, and John Cooper Works vehicles sold, or ever registered, in Alaska, Colorado, Connecticut, Delaware, Illinois, Indiana, Iowa, Kansas, Kentucky, Maine, Maryland, Massachusetts…
Risk and remedy
Risk
An electrical short-circuit can increase the risk of a fire.
Remedy
Dealers will inspect the sunroof drains, interior footwell area, and FRM and, depending upon the results of the inspection, certain components will be replaced. Owner notification letters were mailed May 13, 2024. Owners may contact BMW customer service at 1-866-825-1525.
Owner complaints
118 complaints3 involved a crash10 involved a fire2 injuries
What owners report most
Latest complaints
- Electrical system · Exterior lighting · Visibility/wiper
An authorized manufacturer dealership performed an official safety recall remedy regarding the Footwell Module (FRM) under Campaign 610523 (Repair Order #922462) on a 2007 Mini Cooper. The vehicle was subsequently returned to the consumer in a completely non-compliant, unroadworthy, and highly…
An authorized manufacturer dealership performed an official safety recall remedy regarding the Footwell Module (FRM) under Campaign 610523 (Repair Order #922462) on a 2007 Mini Cooper. The vehicle was subsequently returned to the consumer in a completely non-compliant, unroadworthy, and highly hazardous condition with primary vehicle electronics and safety lighting disabled. Specifically, the low-beam headlights, passenger-side high-beam headlight, all rear tail lights, and the vehicle's electrical sunroof system are entirely non-functional, leaving only a single driver-side high-beam operational. The technician’s service invoices explicitly document a control module programming failure that was bypassed without verifying physical lighting or electronic circuit operations. Due to an administrative records error by the service center, the facility contacted local law enforcement to execute an unannounced welfare check at the consumer's secure residence, actively disrupting a highly sensitive personal safety perimeter involving a domestic violence restraining order. Following the forced immediate pickup of the vehicle, the consumer was subjected to a highly dangerous, 130-mile interstate drive entirely after dark with zero operational front or rear outline safety illumination, creating an extreme and life-threatening physical hazard to the vehicle occupants and surrounding traffic. The service facility has failed to provide a functional or compliant recall remedy and closed out the safety recall electronically despite the critical safety components remaining disabled.
- Electrical system · Unknown or other
I recently purchased a used MINI Cooper with incomplete NHTSA Safety Recall 23V-337 involving the Footwell Control Module (FRM). The previous owner did not complete the recall remedy. The vehicle's turn signals and brake lights are currently inoperative. The FRM controls various vehicle lighting…
I recently purchased a used MINI Cooper with incomplete NHTSA Safety Recall 23V-337 involving the Footwell Control Module (FRM). The previous owner did not complete the recall remedy. The vehicle's turn signals and brake lights are currently inoperative. The FRM controls various vehicle lighting functions and is the component involved in Recall 23V-337. Because I purchased the vehicle with these conditions already present, I do not know what warning lamps, messages, or symptoms occurred before the failures. The loss of both turn signals and brake lights creates a significant safety risk because other motorists cannot be properly notified when the vehicle is turning, changing lanes, slowing, or stopping. Additionally, Recall 23V-337 states that corrosion of the FRM can potentially result in a short circuit and, in rare cases, a thermal event that could increase the risk of injury. The vehicle has not yet been inspected to determine whether the current lighting failures are directly caused by the recalled FRM, but the recall remains incomplete and the vehicle is available for inspection. I contacted BMW/MINI seeking completion of the recall. I was informed that it must be performed by an authorized MINI dealer. There is no authorized MINI dealer in Montana, and the nearest facility is approximately 500 miles away. BMW/MINI declined transportation assistance, mobile repair, or authorization for a closer BMW dealer or qualified repair facility. Although the vehicle can move under its own power, driving approximately 500 miles without brake lights or turn signals, while it also has an outstanding recall involving a potential electrical short circuit and thermal event, presents a serious safety concern. I am actively attempting to complete the recall and am requesting NHTSA review the safety issue and BMW/MINI's lack of a practical means for safely accessing the recall remedy.
- Electrical system · Exterior lighting · Fuel/propulsion system
What happened: Vehicle has experienced failure of the Footwell Control Module (FRM) and associated wiring harness in the driver footwell area, consistent with NHTSA Recall 23V-337. Symptoms: • Exterior lights (headlights / taillights) remain illuminated far longer than normal after vehicle…
What happened: Vehicle has experienced failure of the Footwell Control Module (FRM) and associated wiring harness in the driver footwell area, consistent with NHTSA Recall 23V-337. Symptoms: • Exterior lights (headlights / taillights) remain illuminated far longer than normal after vehicle shutoff, sometimes not turning off at all. • Inspection revealed melted wiring, melted connector plugs and receptacles for headlight/taillight circuits. • Water was found in driver side footwell in the past / under carpet padding. Carpet pad is saturated. This is the same failure mode described in Recall 23V-337: "Due to a number of contributing factors, over time, the FRM could become susceptible to corrosion. Eventually, the corrosion could potentially result in a short circuit, resulting in a potential thermal event which could increase the risk of a fire or injury." Safety risk: Melted wiring and connectors create short circuit and thermal event risk, including fire risk while vehicle is parked and unattended. Lights failing to shut off creates dead battery / loss of exterior lighting control. I am concerned about vehicle fire. My vehicle shows evidence of having caught fire at the headlight and receptacle point. Recall history: Vehicle is included in NHTSA Campaign 23V-337000 (MINI Recall 23V-337 - Footwell Module Moisture/Water Intrusion). I was told remedy is still being developed / parts unavailable, or that additional wiring harness damage beyond the FRM itself is not fully covered. Dealer has inspected the vehicle and has completely disregarded the recall, which was the reason why I brought it in and have quoted me customer pay estimates for repairs covered under the recall. I am filing this to document that Recall 23V-337 failure has resulted in melted wiring harness components beyond just the FRM module, and to request NHTSA evaluate whether the current recall remedy fully addresses wiring harness damage caused by prolonged FRM corrosion / lights staying on.
- Electrical system
The authorized dealer performed a non-compliant remedy for Safety Recall 23V-337. The initial repair resulted in melted wires and a charred connector due to high resistance. The dealer's subsequent re-repair utilized an un-staggered cluster of approximately 8 inline crimp connectors in a single…
The authorized dealer performed a non-compliant remedy for Safety Recall 23V-337. The initial repair resulted in melted wires and a charred connector due to high resistance. The dealer's subsequent re-repair utilized an un-staggered cluster of approximately 8 inline crimp connectors in a single tight bundle.This directly violates BMW Factory Repair Standard ISTA/AIR 61 13, which explicitly mandates: 'Arrange individual interfaces in an offset manner when repairing multiple cables. The wiring harness thus does not become too thick at the repaired point.' By failing to offset the splices, the dealership created a thick, bunched thermal mass that traps heat and strains the circuits, leaving an active passenger cabin fire hazard intact. Delivery has been officially refused
- Electrical system
The contact owns a 2007 Mini Cooper. The contact stated that while driving at an undisclosed speed, the engine seized. No warning lights were illuminated. The vehicle was towed to the residence. The contact, who was an independent mechanic, researched and diagnosed the failure with water damage to…
The contact owns a 2007 Mini Cooper. The contact stated that while driving at an undisclosed speed, the engine seized. No warning lights were illuminated. The vehicle was towed to the residence. The contact, who was an independent mechanic, researched and diagnosed the failure with water damage to the junction box electronics. The manufacturer was made aware of the failure but provided no assistance. The contact referenced an unknown recall that had a similar failure description; however, the VIN was not under recall. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 116,000.
- Air bags · Electrical system
The airbag warning light randomly remains on. From what I understand this is a known issue as there has been previous recalls by Mini. This could potentially mean the airbag system is faulty and non-operational. Based on online searches, it seems like a lot of there problem are wiring problems…
The airbag warning light randomly remains on. From what I understand this is a known issue as there has been previous recalls by Mini. This could potentially mean the airbag system is faulty and non-operational. Based on online searches, it seems like a lot of there problem are wiring problems though, bad connections. The previous recalls should be extended further, as there are other cars with the same problem, like mine.
- Air bags · Seats
On almost all r56 model mini coopers the passenger seat occupancy sensor has a major malfunction that causes it to fail and pop up an airbag sensor light even when someone is sitting in the seat, Mini USA did not issue a recall but rather a reimbursement form for owners in 2017 the last year of…
On almost all r56 model mini coopers the passenger seat occupancy sensor has a major malfunction that causes it to fail and pop up an airbag sensor light even when someone is sitting in the seat, Mini USA did not issue a recall but rather a reimbursement form for owners in 2017 the last year of production for that car and did not publicly disclose this. I feel as though this should be a recall as it is common enough for bypass devices to be normal for this car
- Engine
[XXX]. Mini Cooper 2007-2013: Recalls and TSB. My car is part of a recall under MINI Recall for Timing Chains. I understand now it was settled as part of a class action lawsuit that extended the warranty. I always take my car to a dealer and now after mileage they told me that they want me to…
[XXX]. Mini Cooper 2007-2013: Recalls and TSB. My car is part of a recall under MINI Recall for Timing Chains. I understand now it was settled as part of a class action lawsuit that extended the warranty. I always take my car to a dealer and now after mileage they told me that they want me to pay out of my pocket. My car is a 2007 S. My mileage is 105,000K miles. The recall notice is for the year of my car and they are saying my car is too old and the mileage. This recall is for the year of my car so I am not understanding. Upon inspection by the dealer, it and needs to be replaced and cost $4,100.00. I don't have that kind of money. . My name is [XXX], [XXX]., [XXX], [XXX]. Phone #[XXX]. The dealership is Mini Cooper 1660 E.Spring Street, Long Beach Ca 90806. I never received this recall notice and knew of this only because I took my car to the dealer for something else related for the 3rd time.
- Electrical system
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The…
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated the key fob failed to lock and unlock the vehicle, causing the contact to manually lock and unlock the vehicle. The contact also stated that the radio would change stations or power off independently. The vehicle had been taken to an electrician who referred the contact to the dealer. The dealer was contacted. The manufacturer was made aware of the failure. The failure mileage was 153,000. VIN tool confirms parts not available.
- Electrical system
The open recall for this vehicle has been open for 15 months now. Meanwhile my wife's car remains broken down with a bad footwell module due to the exact reason the recall is being issued. I contacted mini and they said I'd have to pay for repairs out of pocket and apply for reimbursement after…
The open recall for this vehicle has been open for 15 months now. Meanwhile my wife's car remains broken down with a bad footwell module due to the exact reason the recall is being issued. I contacted mini and they said I'd have to pay for repairs out of pocket and apply for reimbursement after they come up with a remedy. I have issues with this for a few reasons. First, the repair is costly. Second, it's already been over a year since the recall has been issued, and still no remedy so who knows when they'll actually have one. Third, they said that even if I pay for repairs out of pocket there's no guarantee I'd get reimbursed for them. In my opinion, for something as serious as this recall, the manufacturer should be on the clock to determine the remedy and repair customers cars. It would be nice if BMW/Mini would get some pressure to get this resolved so the my wife and the thousands of other people affected by this can enjoy the vehicles they spent their hard earned money on without worry that it might spontaneously burst into flames.
- Electrical system
The contact owns a 2007 Mini Cooper. The contact stated while operating the vehicle, the check engine, ABS, and Dynamic Stability Control (DSC) warning lights remained illuminated, and the vehicle lost motive power and stalled. The vehicle was taken to the local mechanic who diagnosed that the foot…
The contact owns a 2007 Mini Cooper. The contact stated while operating the vehicle, the check engine, ABS, and Dynamic Stability Control (DSC) warning lights remained illuminated, and the vehicle lost motive power and stalled. The vehicle was taken to the local mechanic who diagnosed that the foot well control module was faulty and needed to be replaced. The vehicle was not yet repaired. The local dealer was notified of the failure and the contact was informed that the VIN was not included in NHTSA Campaign Number: 23V337000 (Electrical System). The contact stated that the vehicle had experienced the failure listed in the recall. The manufacturer was not yet contacted. The failure mileage was 130,000.
- Electrical system · Fuel/propulsion system · Service brakes
The vehicle has been presenting issues with breaks, electrical issues, turning off while driving, misfires, air bags don't work, ADAS sometimes don't work, the vehicle chokes and has difficulty running at times, among other issues. There has been a recall since last year and I've tried contacting…
The vehicle has been presenting issues with breaks, electrical issues, turning off while driving, misfires, air bags don't work, ADAS sometimes don't work, the vehicle chokes and has difficulty running at times, among other issues. There has been a recall since last year and I've tried contacting the manufacturer multiple times, but the issue has not been fixed yet. All of these problems are a great safety hazard for me and my family while on the road.
- Electrical system · Exterior lighting
My Mini Cooper was rendered unsafe to drive as most of the exterior lights (i.e., headlights, brake lights, turn signals) stopped working--all at once. A local mechanic verified that the electrical short resulted from a severely corroded Footwell Control Module, which is the subject of the recall…
My Mini Cooper was rendered unsafe to drive as most of the exterior lights (i.e., headlights, brake lights, turn signals) stopped working--all at once. A local mechanic verified that the electrical short resulted from a severely corroded Footwell Control Module, which is the subject of the recall (Recall No. 23V-337, July 2023) for which a "Remedy is Unavailable." When contacted, a case management specialist of BMW of North America could tell me only that a remedy is not yet available. Again, the car is unsafe to drive as it lacks exterior lighting. As such, I am forced to purchase another vehicle as the Mini Cooper sits unusable.
- Electrical system
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable…
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
- Air bags
[XXX] . Airbag sensor recall. My car is part of a recall under MINI Recall 23V-xxx: Footwell Module. I took my car to a dealer and they told me that they would not repair it because my car is a 2007. My mileage is 102,000K miles. The notice says Im covered but they say im not. The recall…
[XXX] . Airbag sensor recall. My car is part of a recall under MINI Recall 23V-xxx: Footwell Module. I took my car to a dealer and they told me that they would not repair it because my car is a 2007. My mileage is 102,000K miles. The notice says Im covered but they say im not. The recall notice is for the year of my car and they are saying my car is too old. This recall is for the year of my car so I am not understanding. A light comes on that shows the passenger airbag. Upon inspection by the dealer, it is a faulty seat mat sensor and needs to be replaced and cost $2,120.56. I dont have that kind of money. This should be addressed under the recall. My name is [XXX] , [XXX] . Phone [XXX] . The dealership is Mini Cooper Downtown Los Angeles. 6333 S Almeda Los Angeles Ca 90001. I never received this recall notice and knew of this only because the light indicator came on. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
- Electrical system
I was notified in July 2023 by NHTSA of the potential failure of the Footwell Control Module and subsequent potential "thermal event which could increase the risk of a fire of injury." Apparently, a fix for this issue has not been developed yet. I am afraid to keep my car in the garage, which is attached to my house. 7 months. Does BMW engineering really not know how to replace this poorly-designed component?
- Air bags · Seat belts
Seat belt warning for passenger seat stays on despite buckling the seat belt. I suspect the air bag deployment is therefore not functioning.
- Electrical system
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
- Electrical system
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2007 Mini Cooper. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
- Air bags · Seat belts
Restraint System Malfunction Fault in passenger-restraint system effecting airbag, belt tensioner or belt-force limiter. Having to replace passenger seat or sensor to indicate I have a passenger so the airbag will deploy. It looks like there may have been a recall for this in the past according to an article I found, but my VIN does not come up as needing this item replaced. Cost is approximately $800.
- Engine
On 2014 a Class Action Lawsuit was filed against BMW OF NORTH AMERICA for claims regarding MINI COOPER models. Answering your questions as follows: -The failing component was the timing chain tensioner -Yes, engine stalled at any speed -No, dealer did not acknowledge the real problem -No, dealer…
On 2014 a Class Action Lawsuit was filed against BMW OF NORTH AMERICA for claims regarding MINI COOPER models. Answering your questions as follows: -The failing component was the timing chain tensioner -Yes, engine stalled at any speed -No, dealer did not acknowledge the real problem -No, dealer did not told me about the Class Action Lawsuit, did not advice me of any preventive repair or to install a new timing chain tensioner, when the component failed dealer told me that the problem was a jumping timing chain ; the same excuse as in the lawsuit. -There was only an engine light, not any other warning light There were two repairs, the first for $ 2,629.10 on 6/18/2016 the second for $ 3,354.93 on 1/13/2017 dealer had a two years parts and labor warranty that didn't honor and in 2016 the lawsuit was active and not of my knowledge. My question is: if the production numbers engraved on the timing chain tensioner cylinder face match or are part of the production batch from the factory for which the class action lawsuit took place ? Numbers top line: 7565868 80-02 Lower line: IV/ IS GERMANY 3 1 0 This is looks like half cero All components (parts) and the vehicle are available for inspection. Once engine is out of timing pistons will hit the valves (interference engine), in my engine broke at least one valve seat, pieces fell into combustion chamber getting stuck between pistons and cylinder walls scratching these, result lost of compression, engine die. Engine was beyond any repair, and still was charged for. Lawsuit for vehicles manufactured goes to April 2007 mine was February 2007 Neither the MINI COOPER dealer or BMW North America corporate offices paid any attention to my complaint.
- Air bags
There is a warning light of airbag. But it havent reported when i purchased by a previous owner and carfax as well
- Air bags · Seat belts
2007 mini cooper s airbag light with warning on navigation screen saying seat belt tensioner or belt force limiter has a problem and passenger airbag is off. Odometer is 76,000 when problem started.
- Engine
TL* the contact owns a 2007 MINI cooper. The contact stated while at a standstill, the vehicle began to emit smoke from the engine compartment. The contact stated check engine warning light was illuminated. The vehicle was taken to local dealer schomp MINI (1001 plum valley ln, highlands ranch, co…
TL* the contact owns a 2007 MINI cooper. The contact stated while at a standstill, the vehicle began to emit smoke from the engine compartment. The contact stated check engine warning light was illuminated. The vehicle was taken to local dealer schomp MINI (1001 plum valley ln, highlands ranch, co 80129 (303) 872-5752) where it was diagnosed that the thermal housing needed to be replaced. Upon investigation, the contact associated the failure with nhtsa campaign number: 18v248000 (engine and engine cooling) however the vin was not included. the vehicle was not repaired. the manufacturer had not been informed of failure. The failure mileage was approximately 138,867.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10245428Cavity protection applied to underside of the hood is leaking out onto the wheel arch trim and grille.
- 10244507MINI electrical systems have continued to develop over the past few years. As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle discharged battery complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.
- 10216756N12 Tank leak diagnostic module (DMTL) pump:limited warranty extension to 10 years/120,000 miles
- 10206696New RDC wheel electronics will be introduced with future generation MINI models. The new wheel electronics are identified as Huf Generation 5. These new wheel electronics will need to be programmed using the new tool when replaced or when depressurized (0 psi) for more than 2 minutes.
- 10179827OC3 SEAT OCCUPANCY MAT - LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES: Component-Specific Limited Warranty Extension For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (MINI USA) is extending the limited warranty for the front passenger's OC3 seat occupancy mat (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.
- 10171506CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.
- 10162461Air Conditioning System Leak Testing. The customer complains of poor or no air conditioning cooling. After further diagnosis, the system is found to be low or empty of a refrigerant charge, but when using an electronic leak detector, no leak can be found. CAUSE: In most cases, an electronic leak detector is not sufficient for identifying small leaks in the system. Electronic leak detectors can give false alarms and can lead to an improper diagnosis of small leaks. A leak cannot be located exactly if accessibility is impaired (in the case of the expansion valve, evaporator or condenser).
- 10162460Service Action: Checking or Replacing the Door Sill Trim Strips. The door sill trim strips are deformed and/or peeling up at the corners. CAUSE: Insufficient surface preparation of the door sill.
- 10153778OC3 seat occupancy mat: limited warranty extension to 10 years/120.
- 10152680"MANUAL TRANSMISSION - STIFF DIAGONAL GEARSHIFT LEVER MOVEMENT. The customer may complain of a ""stiff diagonal shift"" (e.g., N-R, R-N, 2-3/3-2 or 4-5/5-4). Also, in some cases, gears cannot be selected, or the selector gear does not go into the neutral position. CAUSE 1. The deflection lever circlip of the gearshift mechanism is damaged or missing. 2. Possible corrosion at the gearshift mechanism (shift cables or transmission gearshift unit)"
- 10151349Bluetooth Connection Failures This Service Information bulletin supersedes SI M84 01 14 dated February 2016.. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware
- 10151347Delay in Automatic Driving Light Switching on/off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes. Shut-off period varies based on detected situation. This is normal operational behavior.
- 10151222"N12 Tank Leak Diagnostic Module (DMTL) Pump: Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION This updated version of this bulletin now includes the addition of the model year 2009 R55, R56 and R57 MINI Cooper vehicles with the N12 engine. For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the Tank Leak Diagnostic Module (DMTL) Pump to: 10 years/120,000 miles as determined by the vehicle's original in-service date Component #1: This ""component specific"" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the MINI New Passenger Car Limited Warranty. GRUSB0116-04 This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release for the additional MY 2009 vehicles."
- 10151060This Service Information bulletin supersedes SI M84 01 14 dated November 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: z Apple iPhones z Samsung S6 and the S6 Edge. Connectivity failure examples are: z Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. z Contact List incomplete z General connection failures z Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) z Samsung S6 and S6 Edge device firmware
- 10150985?OC3 SEAT OCCUPANCY MAT: LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. This Service Information bulletin supersedes SI 01 11 16 dated December 2016.
- 10150357?SUBJECT DWA (Anti-theft Alarm System): False Alarm Is Triggered Intermittently. When the vehicle is parked and locked (DWA active), the alarm system is triggered intermittently. One or more of the following conditions may trigger the alarm system: Sun roof in the tilted/open position, Window partially open, Excessive local noise (for example, near an airport, on a busy road, or in heavy rain) CAUSE Normal sensitivity of the interior ultrasonic sensor.
- 10150356"Discharged Battery: Energy Diagnosis Must Be Performed. MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle ""discharged battery"" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To properly repair the vehicle the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. The procedure below will guide the technician to properly repairing the vehicle and getting paid for a warranty claim. CAUSE Discharged battery."
- 10150347During Engine Oil Service a Small O-Ring Is Found in the Oil Filter Housing. No customer complaint has been received. During the scheduled engine oil service, the technician notices a black rubber o-ring lying on the bottom of the engine oil filter housing. The o-ring has been dislodged from the non-return valve inside the engine oil filter housing. No subsequent engine damage occurs from the dislodged o-ring. Engine oil filter housing (1) Rubber o-ring (2) The material dimensions of the rubber o-ring are not satisfactory, allowing it to become dislodged from its installation location.
- 10150309Squeaking Noise from Front Seat. A noise may be heard from the front driver's seat back when the customer applies sideways pressure during cornering. CAUSE Surface corrosion on the metal seat back frame can make a squeaking noise when rubbing against the foam rubber padding of the seat back.
- 10150308Bonnet Lock Difficult to Open or Close. The bonnet lock fails to operate correctly and is difficult to open or close. CAUSE Corrosion in the bonnet lock assembly
- 10150305Adjusting Rear Camber. Rear camber cannot be adjusted properly. CAUSE Repair instructions not followed properly
- 10150301DMTL Pump: Warranty Extension to 10 Years/120,000 Miles. On affected vehicles, the Tank Leak Diagnostic Module (DMTL) pump can fail. Some vehicles will have the Service Engine Soon lamp illuminated, but the vehicle's drivability and engine performance will not be reduced by this DMTL pump malfunction.
- 10150241Incorrect Customer Relations Telephone Number Is Saved in the Vehicle. The customer is not connected to MINI Customer Relations after dialing the number displayed in the vehicle Kombi or radio. CAUSE During the Pre-Delivery Inspection (PDI), the incorrect telephone number is being written into the vehicle. INFORMATION 1. When performing the PDI test plan, it is extremely important that you select MINI if the ISID is configured for both BMW and MINI. 2. After completion of the PDI test plan, verify that the customer relations number stored in the vehicle is correct. 3. The correct customer relations phone number is 1(866) 275-6464. 4. If the number stored in the vehicle is incorrect and the correct test plan was used, contact your 3g Administrator and have him or her verify the number stored in the ISID. 5.This picture shows the correct number stored in the Combox control unit. Note: To read out telephone number:
- 10150237?N18 Engine: FC 2BF2 Rail Pressure Sensor Is Stored in DME Fault Memory. The customer states that the Service Engine Soon lamp is illuminated and the following fault is stored in the DME: FC 2BF2 Rail pressure sensor, workspace: pressure too high CAUSE A DME calibration error in the fuel pressure diagnostics results in an increased sensitivity.
- 10150203N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5 C
- 10150091"DWA (Anti-theft Alarm System): False Alarm Is Triggered Intermittently. INFORMATION Parts replacement will not solve the problem if one or more of the conditions described in the situation above caused the alarm to trigger. The sensitivity of the interior ultrasonic sensor cannot be reduced. If the customer wishes to park the vehicle with the sunroof tilted, the window partially open, and/or in an area with excessive local noise, the interior sensor must be switched off by using the following procedure: Press the lock button on the remote control twice in succession. The LEDs flash in short succession for approx. 2 seconds. The interior ultrasonic sensor is switched off until the vehicle is unlocked and locked the next time. NOTE: This information can be found in the Owner's Manual in the ""Controls"" section under ""Switching off the tilt alarm sensor and interior movement detector."""
- 10150046Clicking Noise from Front Axle Brakes.
- 10149623"Discharged Battery: Energy Diagnosis Must Be Performed. MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle ""discharged battery"" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To repair the vehicle properly the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair. CAUSE Discharged battery."
- 10149621Whistling Noise from the Water Pump Area. A whistling or squealing noise is heard from the engine at idle and/or at higher engine speeds. CAUSE 1. Noise is caused by the water pump. 2. Noise is caused by the friction wheel of the belt tensioner.
- 10149507Red or Blue Cap Missing from Temperature Control Wheel. The customer states the red or blue cap is missing from the temperature control wheel of the heat and air conditioning control panel.
- 10149504"MINI GP: Choice of Tire Option Agreement and Alternate Tire Retrofit. The Kumho 215/40 R17 Ecsta V700 sport tire performance optimization results in vehicle operation limitations, specifically when operated in cold climates or on wet, slushy or snow-covered roads. If your MINI JCW GP owner prefers a set of tires that better fits his/her driving style and climate, these owners can swap out the factory-original equipment (OE) Kumho 215/40 R17 Ecsta V700 sport tires for a set of the following MINI approved alternate tires: ??205/45R17 84W John Cooper Works performance run-flat tires Please refer to the attached MINI Product Planning & Strategy Bulletin M-20-0313-0012, ""MINI John Cooper Works GP Unleashed,"" for more information, including the required ""choice of tire option"" agreement form."
- 10149500Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
- 10149464"N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: FC 2D9B Knock Sensor, Signal While performing test plan B1214 M KNOCK SENSOR, the following error message will be displayed: ""An error has occurred during execution of a service program. Fault code: 61/3."" This error in the test plan will not allow diagnosis to continue. The test plan error will be repaired with ISTA/D 2.36.0. CAUSE A DME calibration error in the knock sensor diagnostics results in an increased sensitivity threshold to cold temperatures."
- 10149332Erroneous "Service due" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.
- 10148447iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
- 10148441N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
- 10148391N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.
- 10148358Automatic Deactivation of Recirculation Mode. The customer states the recirculation display goes out, even though the recirculation button was switched on. CAUSE The automatic recirculation air deactivation feature was introduced in July 2012. Note: If the customer dislikes this feature, it can be deactivated by using the following steps.
- 10148349Erroneous "Service due" Message Although Brake Lining Thickness is Above Minimum Specification. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.
- 10148346N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software
Every MINI Cooper model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.