2006 Nissan Xterra
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Nissan › Xterra › 2006
These records cover every 2006 Nissan Xterra. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2006 Nissan Xterra. Newest first.
Nissan IS recalling certain model year 2004-2006 armada, titan, infiniti QX56 and model year 2005-2006 frontier, pathfinder and xterra vehicles. the intelligent power distribution module (ipdm) assembly contains an engine control module (ecm) relay that has a diode for electrical current noise reduction. The ecm relay may allow silicon vapor to form and…
Risk and remedy
Risk
This could cause engine stalling increasing the risk of a crash.
Remedy
Dealers will replace the ecm relay inside the ipdm assembly. This service will be performed free of charge. the safety recall began on december 6, 2010. owners may contact nissan at 1-800-647-7261.
Nissan IS recalling certain front and rear lower links, p/nos. 54501Zq00a, 54500zq00a, 551a1zq00a, 551a0zq00a , 54501ea00a, 54500ea00a, 551a1ea500, 551a0ea500, 54501zr00a, and 54500zr00a, sold between november 25, 2009 and may 14, 2010 as replacement parts for model year 2004 through 2010 titan, armada, and QX56, and model years 2005 through 2010 frontier…
Risk and remedy
Risk
If the collar weld separates, the vehicle handling will deteriorate, possibly resulting in a vehicle crash.
Remedy
Nissan will notify owners and dealers will replace any affected lower link free of charge. the safety recall began on july 12, 2010. owners may contact nissan at 1-800-647-7261.
Nissan IS recalling certain model year 2006 and model year 2008 frontier, xterra and pathfinder vehicles. the molded fuel tank shells can deform, causing the fuel sender float arm to contact an embossment molded into the tank shell causing the instrument panel fuel gauge to show that the vehicle has approximately one quarter tank when the fuel tank IS…
Risk and remedy
Risk
This could cause the vehicle to run out of gas and stall in traffic, increasing the risk of a crash.
Remedy
Dealers will replace the fuel level sending unit inside the fuel tank with a new one that has a modified float arm. this service will be performed free of charge. the safety recall IS expected to begin on or before march 22, 2010. owners may contact nissan at 1-800-647-7261.
Nissan IS recalling 242,720 my 2005-2009 pathfinder, frontier and xterra vehicles originally sold in or currently registered in the states of connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin…
Risk and remedy
Risk
This issue could result in the non-deployment of the driver and passenger front air bags in a crash, increasing the risk of personal injury.
Remedy
Dealers will replace the front czs with a redesigned sensor. the recall began on january 26, 2009. owners in the other states will receive extended warranty coverage for the sensor to 10 years. these owners will be notified of the warranty extension by mail and will receive a sticker to place in their warranty booklet explaining the extended warranty coverage. owners may contact nissan at 1-800-647-7261.
Certain hopkins aftermarket trailer brake control connection harnesses sold for use on certain models of nissan vehicles which are listed above. the internal part numbers within hopkins are: 1010476025, 1040376025, 1110476025, 1170376025, 1290376025, 1010476035, 1040376035, 1110476035, 1170376035, and 1290376035. a wire may have been placed in an…
Risk and remedy
Risk
This harness would result in power from the trailer brake controller going to the towing vehicle dash light circuit rather than the trailer brakes. this result would be the lack of trailer braking when the towing vehicle brakes were applied. it would also result in the towing vehicles dash lights being activated when the vehicle brakes were applied. the failure of the application of the trailer brake could result in reduced ability to stop and contribute to a possible crash.
Remedy
Hopkins will notify owners and replace the original harness with a revised harness free of charge. the recall began august 17, 2007. owners can contact hopkins at 800-835-0129.
Owner complaints
780 complaints12 involved a crash3 involved a fire19 injuries1 deaths
What owners report most
Latest complaints
- Power train · Seat belts · Service brakes
I have a lot of ticking and stalling lights are blinking I think it’s may be the transmission and I smell gas inside the vehicle.
- Tires
17
- Air bags
The contact owns a 2006 Nissan Xterra. The contact stated that there was an abnormal sound coming from the front passenger's side air bag intermittently. The front passenger's side air bag warning light was illuminated. The vehicle was taken to the dealer, where the contact was provided a cost for…
The contact owns a 2006 Nissan Xterra. The contact stated that there was an abnormal sound coming from the front passenger's side air bag intermittently. The front passenger's side air bag warning light was illuminated. The vehicle was taken to the dealer, where the contact was provided a cost for a diagnostic test. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 145,000.
- Engine
The timing chain has caused my vehicle to die on me in the middle of a busy highway I was almost hit by a few cars. I had to drive my car going only 40 mph all the way becasue that IS all it would do. It has a very loud noise and it IS unsafe to drive on the road anymore. I have read and nissan…
The timing chain has caused my vehicle to die on me in the middle of a busy highway I was almost hit by a few cars. I had to drive my car going only 40 mph all the way becasue that IS all it would do. It has a very loud noise and it IS unsafe to drive on the road anymore. I have read and nissan should replace these because alot of people have had problems with them yes my car IS available for imspection I have regular kept maintenence on it no there were no warning lamps at all just loud noise and then no compression
- Air bags
The contact owns a 2006 Nissan Xterra. The contact received notification of NHTSA Campaign Number: 23E012000 (Air Bags) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of…
The contact owns a 2006 Nissan Xterra. The contact received notification of NHTSA Campaign Number: 23E012000 (Air Bags) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and confirmed parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
- Air bags
The contact owns a 2006 Nissan Xterra. The contact received notification of NHTSA Campaign Number: 23E012000 (Air Bags) however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed that parts were not yet available. The contact stated that the…
The contact owns a 2006 Nissan Xterra. The contact received notification of NHTSA Campaign Number: 23E012000 (Air Bags) however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was contacted and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
- Engine · Service brakes
Timing chains making noises and I have change my oil and it still making the noise...
- Electrical system · Fuel/propulsion system · Power train
Car just shut off in traffic loosing all power and braking causing me to crash into the back of a stopped car at a red-light. After inspection from a mechanic shop, they informed me that something in the computer had fried causing the car to shut off, and it had also caused the transmission control unit module to go bad making the car not drive able.
- Engine
Engine noise: - Noise coming from time belt support - The timing chain guide wore out fast. - Timing chain guide inner plastic wore out causing chain to rely metal bracket then the metal causing noise and eventually break the the timing chain.
- Fuel/propulsion system
Check engine light is on and fuel gauge does not work Can go from full to empty Stays on empty even though I know there is gasoline in tank Has caused us to run out of gas middle of nowhere
- Engine and engine cooling › Exhaust system › Emission control › Catalytic convertor
The contact owns a 2006 Nissan Xterra. The contact stated while driving 20 MPH, the vehicle was shaking. The vehicle was taken to an independent mechanic, who replaced the catalytic converter; however, the failure recurred. The vehicle was towed back to the independent mechanic, who diagnosed that…
The contact owns a 2006 Nissan Xterra. The contact stated while driving 20 MPH, the vehicle was shaking. The vehicle was taken to an independent mechanic, who replaced the catalytic converter; however, the failure recurred. The vehicle was towed back to the independent mechanic, who diagnosed that there was an engine misfire and the other catalytic converter needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 136,900.
- Unknown or other
On the invoice/receipt the part of automobile is Plenium Seal CK WP. The remarks/labor description on invoice indicates repairing vacuum hose at read of throttle. My car simply stalled while driving on a main busy street. Fortunately, it was on a holiday (Feb 21, 2022) and there were no school…
On the invoice/receipt the part of automobile is Plenium Seal CK WP. The remarks/labor description on invoice indicates repairing vacuum hose at read of throttle. My car simply stalled while driving on a main busy street. Fortunately, it was on a holiday (Feb 21, 2022) and there were no school crossings on this day!. I was shaken up, anxious. There was a nearby (with in a quarter mile or so) an independent auto repair/service shop and I was able to have them fix the issue. I feel this is a safety issue, as this could have been worse, and stalled while driving on the freeway. I will be writing to the manufacturer to inform them what has happened. There were no other warning signs prior to the vehicle stalling while driving.
- Electrical system › Instrument panel › Fuel gauge
The contact owns a 2006 Nissan Xterra. The contact stated while driving 60 MPH, the vehicle lost motive power and stalled with the fuel level warning light illuminated. The fuel gauge failed to operate as needed. The vehicle was towed to a parking lot. The vehicle was not taken to a dealer nor independent mechanic. The manufacturer was not informed of the failure. The failure mileage was 159,000.
- Engine
My engine self destruct because Nissan used cheap made plastic tensioners that shredded metal into my engine causing it to self destruct. Nissan knew about this problem and continued installing these tensioners from 2005-2015. I could have crashed into anything while driving or someone could have…
My engine self destruct because Nissan used cheap made plastic tensioners that shredded metal into my engine causing it to self destruct. Nissan knew about this problem and continued installing these tensioners from 2005-2015. I could have crashed into anything while driving or someone could have hit me if my engine would’ve died while driving. My safety was not prioritized by Nissan. The warning light was a whining noise coming from the engine while startup and pressing on the gas pedal. So they knew the problem existed but didn’t care.
- Power train
The transmission was destroyed because a factory default with the radiator leaking antifreeze and transmission fluid into the transmission causing my transmission to self destruct. my safety was not safe since Nissan knew about the defect and I could have ceased into Anything at any time. There was no warning lights it just self destruct. Nissan has done nothing to inspect their failure. It is a well known problem.
- Electrical system · Fuel/propulsion system
When I turn the key in the on position all lights come on and the motor does turn over. I took it to the dealer and they replaced the starter and a week later it does the same so I ran a diagnostic test and p0181 code and 3RD coil pack misfire comes on. When I contact nissan mechanic he said there was a recall on the ipdm and thats why I'm contacting you all
- Air bags · Seat belts
Got into accident with my 2006 nissan xterra off road. Was driving at 8:05 pm at 30 mph down ponce de leon passing 207 in st. Augustine florida. A 2016 nissan pathfinder was stopped while traffic was moving I tried to avoid the nissan, no time to brake, it clipped the backside of the pathfinder…
Got into accident with my 2006 nissan xterra off road. Was driving at 8:05 pm at 30 mph down ponce de leon passing 207 in st. Augustine florida. A 2016 nissan pathfinder was stopped while traffic was moving I tried to avoid the nissan, no time to brake, it clipped the backside of the pathfinder with my xterra. My driver side and passenger airbag went off. (Exploded?) it broke my passengers arm and unknown object in passengers eye. Airbags blown out destroyed my dash air bag IS ripped like it had a baby. Both my passenger and driver side seat belts both released the seat belts they didn't lock during the accident usually they lock and won't release my driver side IS not locking in place as the passenger. Days after the accident my passenger had her (2003 nissan sentra)recalled for the takata recall , inspected was positive for the recall and replaced it was describing the situation for this accident I was told by a lawyer to report this to nhtsa. Suspected takata airbags. I pulled the vin no recall I bought this truck maybe a month prior. I'm completely unknown of this situation. Insurance company wanted to total the xterra I took it home I still have the vehicle inside with airbags both insurance companies are progressive the driver V02 had no license the officer was too busy to proceed with the investigation of how the accident happened. The damages was not bad to break a bone with an airbag at the speed and impact this car accident had.
- Power train
TL* the contact owns a 2006 nissan xterra. The contact stated that the vehicle loss motive power while driving. The contact stated that while attempting to move from a stop, the vehicle failed to accelerate. The contact stated that the vehicle revved up between 2,000 - 3,000 rpm however, the…
TL* the contact owns a 2006 nissan xterra. The contact stated that the vehicle loss motive power while driving. The contact stated that while attempting to move from a stop, the vehicle failed to accelerate. The contact stated that the vehicle revved up between 2,000 - 3,000 rpm however, the vehicle failed to respond with the check engine warning light illuminated. The vehicle was taken to and independent mechanic and was diagnosed that coolant had leaked into the transmission and that the transmission failed due to the coolant contamination. The mechanic informed the contact that the transmission and radiator needed to be replaced. The vehicle was not repaired. Neither a dealer nor the manufacturer were contacted or notified of the failure. The failure mileage was 111,000.
- Electrical system · Fuel/propulsion system · Unknown or other
The gas gauge doesn't work
- Engine · Unknown or other
Transmission started jerking and radiator blew at the same time
- Unknown or other
There was a safety recall for radiators in nissan xterras in 2019 , I was never informed about this recall or service bulletins even though nissan knows I own the vehicle in their database also there IS an electrical problem with the ipdm box which IS defective according to the nissan pages on…
There was a safety recall for radiators in nissan xterras in 2019 , I was never informed about this recall or service bulletins even though nissan knows I own the vehicle in their database also there IS an electrical problem with the ipdm box which IS defective according to the nissan pages on facebook and other sites, where the white ipdm box IS defective and causes power loss and lights not working along with car stalling while driving, it IS apparently a defect and the cost to replace it IS over I was never notified of the xterra transmission cooler defect or recall back in 2019, ive owned this xterra since 2008 and its been to the dealer for another previous recall, also there IS a problem with the white ipdm box, (fuse box) which should be investigated, per the nissan owners facebook page, and other blogs the ipdm causes stalling and shutdowns of all functions in the 2005-2014 nissans, consumers are having to pay upwards of $600 to the dealership for these defective ipdm boxes, there IS a known defect which was recalled years ago about a relay for that box, I believe my xterra relay was fixed, but I am having a problem with the vdc/ slip light coming on and my headlights go on and off while driving at night. According to the websites it has to do with the white ipdm box underneath where the wires are harnessed, this needs to be adressed it IS a safety hazzard while driving on the highway or in town because the vehicle IS totally disabled and will cause injury/death ive been reading nissan pages to find out why my lights are going on and off, ive repalced the camshaft and crankshaft pos sensors, nissans previous recall for a diode apparantly this didnt fix it, it just masked the situation, read up on newx.org about this problem
- Electrical system · Engine · Power train
Radiator failed, coolant mixed/leaked into the transmission fluid and caused the transmission to fail. Gas gauge quit working properly
- Fuel system, gasoline
TL* the contact owns a 2006 nissan xterra. The contact stated that while driving at 15 mph, the accelerator pedal was depressed and the check engine warning light illuminated. The vehicle was taken to the dealer riverside nissan (8330 indiana ave, riverside, ca 92504) where it was diagnosed and…
TL* the contact owns a 2006 nissan xterra. The contact stated that while driving at 15 mph, the accelerator pedal was depressed and the check engine warning light illuminated. The vehicle was taken to the dealer riverside nissan (8330 indiana ave, riverside, ca 92504) where it was diagnosed and determined that the fuel level sending unit failed and needed to be replaced. The vehicle was not repaired. The contact mentioned nhtsa campaign number: 10v075000 (fuel system, gasoline) as a possible solution to the failure however, the vin was not included. The manufacturer was made aware of the failure. The manufacturer confirmed that there was no recalls associated with the vin. The failure mileage was approximately 80,000.
- Power train
I was required to replace the oem radiator due to appearance of cross-contamination between automatic transmission fluid and engine coolant. the discovery was made early enough to avoid being stranded. it IS unknown whether the amount of contamination that preceded the replacement has caused…
I was required to replace the oem radiator due to appearance of cross-contamination between automatic transmission fluid and engine coolant. the discovery was made early enough to avoid being stranded. it IS unknown whether the amount of contamination that preceded the replacement has caused permanent damage, but the vehicle IS functioning normally as of this moment. I am aware that nissan has been challenged on the topic of extended warranty support and/or recall for this issue over a span of years, and this report IS filed to add a data point.
- Engine · Unknown or other
Vehicle has stalled multiple times, both in motion and parked. There were no warning signals, strange noises, or other indicators to point to the issue. Additionally, when trying to use the obd port to diagnose the issue, the obd port will not read and only gives an error. *tr
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Transmission Failures
On February 29, 2012 the National Highway Traffic Safety Administration (NHTSA) received a letter petitioning the agency to conduct a defect investigation into MY 2005-2010 Nissan Pathfinder, Frontier, and Xterra vehicles [the subject vehicles] for automatic transmission failures related to failed transmission…
On February 29, 2012 the National Highway Traffic Safety Administration (NHTSA) received a letter petitioning the agency to conduct a defect investigation into MY 2005-2010 Nissan Pathfinder, Frontier, and Xterra vehicles [the subject vehicles] for automatic transmission failures related to failed transmission coolers.NHTSA conducted a comprehensive review of data related to this subject. Our report, documenting this review, is available in the document file for this defect petition.It will also be published in the Federal Register. Of the 2,505 referenced complaints, 638 relate to a potential hazard (unable to maintain speed, no motive power, engine stall) and 1,867 concern customer satisfaction issues including, but not limited to, repair cost, vehicle shudder and shake, and engine overheating.Taking into account the allocation of agency resources and priorities and the likelihood that additional investigation would result in a finding that an unreasonable risk to highway safety exists, we conclude that further investigation is not warranted and deny the petition.ODI Complaint ID numbers are referenced on the next page.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007001VOLUNTARY SAFETY RECALL CAMPAIGN 2005-2013 FRONTIER, PATHFINDER, AND XTERRA; DRIVER AIR BAG COVER CAMPAIGN ID #: PC945 and PC948 APPLIED VEHICLES: 2005-2013 Frontier (D40) 2005-2012 Pathfinder (R51) 2005-2013 Xterra (N50) Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2005-2012 Pathfinder, and 2005-2013 Frontier and Xterra vehicles to inspect and, if necessary, replace the Driver Air Bag Cover. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC945 and PC948 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealers inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
- 11004962VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004961CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004960CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001201WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001194REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001191WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10243708DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10239062SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
- 1023906012 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
- 10235710INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
- 10235707VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10233896ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232658REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232657WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232656WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232652DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10208946CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10206391STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10192821SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Nissan electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
- 10192805IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
- 10192801SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
- 10192727SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
- 10192691IF YOU CONFIRM: A remanufactured automatic transmission supplied by ATC Drivetrain is installed in an APPLIED VEHICLE AND CONSULT-III plus (C-III plus) is not able to communicate with the TCM through Diagnosis (One System) OR C-III plus is able to communicate with the TCM, but the TCM part number?s (P/N) sixth digit is a "5", "6", or "7" (for example, 31020-7xxxx). NOTE: To determine if an applied vehicle is equipped with an ATC Drivetrain remanufactured A/T, see page 3. ACTION: Refer to the Flow Chart on page 2. See this bulletin for further detail.
- 10192677SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
- 10192638SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
- 10192591SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
- 10192524SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
- 10192513SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
- 10192506IF YOU CONFIRM: Squeal/Squeak noise from the front brakes: While moving forward or reverse, with very light brake application (pedal pressure), after the vehicle has been sitting, typically overnight ("cold" brakes), at speeds less than 10 MPH, while traveling straight or turning. ACTION: Replace the hardware on both front brake calipers with the kit listed in the Parts Information in this bulletin. See this bulletin for further detail.
- 10192474SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
- 10192394SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
- 10192326SERVICE INFORMATION The specifications for the intake and exhaust valves and valve lifter service parts have been changed. * The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not shown). These service parts will require that the valve and valve lifter be replaced at the same time. See this bulletin for further details.
- 10192305SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
- 10192233Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
- 10192231SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
- 10192217If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
- 10192216SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
- 10192192As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
- 10192145SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
Every Nissan Xterra model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.