2025 Chrysler Pacifica Plug-In Hybrid

Recalls

1 recall names the 2025 Chrysler Pacifica Plug-In Hybrid. Newest first.

• Service brakes, hydraulic › Critical fasteners

  Mar 27, 2025NHTSA 25V1910008 vehicles

  Chrysler (FCA US, LLC) is recalling certain 2025 Chrysler Pacifica Plug-In Hybrid Electric (PHEV) vehicles. The bolts securing the front brake caliper bracket may not be tightened properly, which can result in reduced steering control, a brake fluid leak, and a loss of front brake function.

  Risk and remedy

  Risk

  Reduced steering control, a brake fluid leak, and loss of front brake function increase the risk of a crash.

  Remedy

  Dealers will inspect and replace the front brake caliper brackets and bolts, as necessary, free of charge. Owner notification letters were mailed April 10, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 27C.

  Full recall details →

Owner complaints

Latest complaints

• Aug 19, 2026FL
  Electrical system
  The contact rented a 2025 Chrysler Pacifica Hybrid from Budget Car Rental (2176 Main St, Dunedin, FL 34698). The contact stated that while driving approximately 55 MPH, the contact believed that the vehicle was being tracked via Bluetooth throughout a trip from Florida to Kansas City to New York…

  The contact rented a 2025 Chrysler Pacifica Hybrid from Budget Car Rental (2176 Main St, Dunedin, FL 34698). The contact stated that while driving approximately 55 MPH, the contact believed that the vehicle was being tracked via Bluetooth throughout a trip from Florida to Kansas City to New York and back to Florida, as the vehicle was surrounded by other vehicles with suggestive and personalized license plates. The contact reported the issue to the Florida Department of Law Enforcement. The manufacturer was not notified of the issue.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11011774Backup Camera Poor Image Quality Inspection
• 11010748Reverse View Camera Inoperative After Recent Repair
• 11010693SWITCH Multifunction Before replacing the steering column control module (SCCM) due to DTC U0212 active, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure all the switches' and airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from wipers is requested, if turn signal, blindspot and lane assistant work. 5.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. If there are no DTC's, physical defects, wipers inop, nor turn signal inop, then SCCM does not need to be replaced Before replacing the steering column control module (SCCM) due to DTC U0212 active, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure all the switches' and airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from wipers is requested, if turn signal, blindspot and lane assistant work. 5.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. If there are no DTC's, physical defects, wipers inop, nor turn signal inop, then SCCM does not need to be replaced.
• 11010511Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
• 11010258"Flash: Powertrain Control Module (PCM) Updates Customers may experience the following: Vehicle may enter Auto Park Mode during an Engine Stop Start (ESS) event. The driver will be notified that the vehicle is entering Auto Park Mode by the blinking D on the shifter for three blinks and then automatically shifting into Park. To shift out of Park, the driver will have to press down on the brake pedal and cycle the ignition back to START, and move the shifter into the desired position This bulletin involves reprogramming the PCM with the latest available software."
• 11009570Switch and bezel - front door
• 11009559Module - inverter
• 11009541MODULE Air Bag Control For vehicles with B2208, B00B5 or U0151 conditions, before replacing the ORC Module, check the circuit wiring and connector first for any Open or Shorted conditions and check vehicle for low-voltage conditions.
• 11008260Isolator - spring
• 11007087Warranty Newsletter Volume 10 Issue 8_ID
• 11007085ACC Sensor Blinded, ACC Unavailable Service Required FCW Unavailable Service Required, Adaptive Cruise Control (ACC) system disabled, Loss of Advanced Driver Assist System (ADAS) Features Messages Displayed on the Instrument Panel Cluster (IPC)
• 11005199CAN Star Block Connector Customer finds MIL light on and technician finds DTC for loss of communication on one or more modules. In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.
• 11004949Malfunction Indicator Lamp on, Diagnostic Trouble Code (DTC) P0EDD-00 Hybrid/EV battery Pack B Deterioration
• 11002752Motor - blower with wheel

Every Chrysler Pacifica Plug-In Hybrid model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.