2014 Ford E-150
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Ford › E-150 › 2014
These records cover every 2014 Ford E-150. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
6 recalls name the 2014 Ford E-150. Newest first.
Mobility Specialists, Inc. (Mobility Specialists) is recalling certain 2014-2017 Ford E-150 and Transit vans modified to be equipped with Ricon S-Series and K-Series wheel chair lifts. The wheelchair lift positioning input cam may fail while the lift is in use, allowing the platform to travel higher than the vehicle's floor height.
Risk and remedy
Risk
If the wheelchair lift platform stops above the vehicle floor, the wheelchair user can tip inwards toward the vehicle when exiting the lift, increasing their risk of injury.
Remedy
Mobility Specialists, working with Ricon, has notified the owners. Ricon will provide instructions and materials for replacing defective parts. Owners may contact Ricon customer service at 1-800-322-2884.
MobilityWorks (WMK Inc.) is recalling certain model year 2006-2014 Ford E-150, E-250, and E-350 vans modified by MobilityWorks to be equipped with certain model S2005, S2010, S5005, S5010, S5505, and S5510 wheelchair lifts manufactured by Ricon Corporation. The affected lifts are equipped with folding link arms that may have pivot holes that are too big…
Risk and remedy
Risk
If the bearings move out of position, the stowed platform may have excessive movement resulting in failure of the platform mounting. This failure could cause the wheel chair lift platform to fall out of the vehicle when the doors are opened, increasing the risk of injury for the lift operator.
Remedy
MobilityWorks will notify owners, and Ricon dealers will inspect the link arms for damage or for displaced bearings. The platform will be inspected for cracks. Any damaged parts will be replaced, free of charge. The recall began on December 15, 2015. Owners may contact MobilityWorks customer service at 1-800-769-8267, or Ricon Customer Service at 1-800-322-2884. Note: These vehicles and wheelchair lifts were subject to a similar recall in 2014. All vehicles that received that recall remedy are still affected by this recall as well.
Cummings Mobility Conversion & Supply (Cummings) is recalling certain model year 2006-2014 Ford E-150, E-250, E-350, Chevrolet Express, 2006-2008 Dodge Sprinter, and 2009-2014 Mercedes-Benz Sprinter, and 2013 Ford Transit Connect vehicles manufactured January 1, 2006, to October 8, 2014, equipped with certain model S2005, S2010, S5005, S5010, S5505, and…
Risk and remedy
Risk
If the platform side plates crack, the lift platform can separate from the lift and come to rest against the vehicle's lift door. When the doors are opened, the platform may fall out, increasing the risk of injury to the lift operator.
Remedy
Cummings will notify owners to take buses to a Ricon dealer or service center who will install supplemental platform support bumpers. Any platform that has already started cracking will be replaced, free of charge. The recall began January 13, 2015. Owners may contact Cumming's customer service at 1-800-639-5438 or Ricon customer service at 1-800-322-2884. Cumming's number for this recall is 14E-041.
National Van Builders, Inc. (National Van) is recalling certain 2007-2014 Ford E-150 and E-250 vehicles manufactured February 26, 2007, to August 19, 2014, and equipped with certain model S2005, S2010, S5005, S5010, S5505, and S5510 wheelchair lifts manufactured by Ricon Corporation. The platform side plate of the affected wheelchair lifts may crack.
Risk and remedy
Risk
If the platform side plates crack, the lift platform can separate from the lift and come to rest against the vehicle's lift door. When the doors are opened, the platform may fall out, increasing the risk of injury to the lift operator.
Remedy
National Van will notify owners to take buses to a Ricon dealer or service center who will install supplemental platform support bumpers. Any platform that has already started cracking will be replaced, free of charge. The recall began on October 3, 2014. Owners may contact National Van customer service at 1-800-527-7477. National Van's number for this recall is Ricon2014.
WMK Inc., doing business as Mobility Works, Inc. (Mobility), is recalling certain model year 2013-2014 Mobility-modified Ford E-150, and E-250 transit buses manufactured December 1, 2013, through January 4, 2014, and equipped with certain Ricon S series and K series wheelchair lifts, with an optional armored pendant cable. The armored cable may be…
Risk and remedy
Risk
If the cable does not clear the wheel chair lift it may contact the power lug and if it does not have a nonconductive cover, or it has an improperly installed non-conductive cover, then a short circuit may occur that could result in a fire.
Remedy
Mobility will notify owners, and Ricon will send the owner a supplemental cover kit and instructions free of charge. The recall began on June 4, 2014. Owners may contact Mobility customer service at 1-800-769-8267, or Ricon Customer Service at 1-800-322-2884 or by e-mail at recall.admin@wabtec.com.
Landi Renzo USA is recalling certain model year 2011-2014 Ford E-150, E-250, and E-350 vehicles modified January 2, 2011, through February 24, 2014 to operate on compressed natural gas (CNG). In the affected vehicles, the left and right rear brackets that support the rear CNG cylinder may fail, allowing the cylinder to dislodge from the vehicle.
Risk and remedy
Risk
If the cylinder dislodges, a CNG leak may result, increasing the risk of a fire.
Remedy
Landi Renzo USA will notify owners, and dealers will inspect and replace the side arm brackets, as necessary, free of charge. The recall began on March 27, 2014. Owners may contact Landi Renzo USA at 1-855-526-3400.
Owner complaints
6 complaints
What owners report most
Latest complaints
- Steering
The van wanders back and forth at highway speeds (> 60mph). I had the front end alignment and suspension checked out - all ok. problem gets worse when pulling a 5000 lb camper - almost a safety issue.
- Service brakes
I only have 8000 miles on it, and the steering wheel IS shaking when I touch the brakes. It also has squeaked from the day I bought it. I took it back to the dealer, they didn't hear the squeak. It IS only when I back up.
- Service brakes
TL* the contact owns a 2014 ford E-I50. The contact stated that the front brake pad was grinding the rotor and caused the steering to pull to the left and right. The dealer shaved the rotor and replaced the pads, but the failure recurred a month later. The vehicle was taken back to the dealer where…
TL* the contact owns a 2014 ford E-I50. The contact stated that the front brake pad was grinding the rotor and caused the steering to pull to the left and right. The dealer shaved the rotor and replaced the pads, but the failure recurred a month later. The vehicle was taken back to the dealer where they shaved the rotor and replaced the pads again, but the failure recurred. When the vehicle was taken back to the dealer, the contact was informed that the vehicle was operating the way it should. The manufacturer was not made aware of the failure. The failure mileage was 11,426.
- Electrical system · Power train
When started 3 separate times 4X4 was engaged by itself just barely touched 4wheel drive switch and it went off also did it again when I was driving
- Visibility › Glass, side/rear
TL* the contact owns a 2015 (na) ford E-150. While the vehicle was in park, the contact heard a loud noise and noticed that the rear driver side window fractured. The vehicle was taken to a dealer. The technician diagnosed that all the rear windows needed to be replaced. The vehicle was repaired.…
TL* the contact owns a 2015 (na) ford E-150. While the vehicle was in park, the contact heard a loud noise and noticed that the rear driver side window fractured. The vehicle was taken to a dealer. The technician diagnosed that all the rear windows needed to be replaced. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was 23,000. updated 4/7/15*cn updated 04/09/15*jb
- Service brakes · Structure · Vehicle speed control › Accelerator pedal
On june 10, 2014 I left my office and traveled across the parking driveway at about 7 mph, a distance of about 150 feet where I attempted to stop(using my right foot on the brake) before making a right hand turn onto a busy fast moving street. At this point my foot hit the brake and accelerator at…
On june 10, 2014 I left my office and traveled across the parking driveway at about 7 mph, a distance of about 150 feet where I attempted to stop(using my right foot on the brake) before making a right hand turn onto a busy fast moving street. At this point my foot hit the brake and accelerator at the same time (they are extremely close) causing me to suddenly lurch forward toward the oncoming traffic coming from my left. fortunately I was able to quickly use my left foot to power brake and safely stop my vehicle. this was the third time in 250 miles of city driving my new vehicle that this had happened, but the first time I recorded the time and date of the incident, realizing there was a design issue. this IS a serious safety problem, I can see many rear end accidents being caused by this design. since I still own a 2004 ford E150 van, side by side measurement comparisons were easily made and I think I can see what has happened. the accelerator pedal has been raised about an inch and a quarter higher than my 2004 van and IS approximately one quarter inch closer to the brake pedal. In addition because of the large engine cowling, the brake pedal IS located mostly to the left of center of the center line of the steering wheel which forces the driver to effectively cross over awkwardly to hit the center of the brake pedal. This IS a very unnatural motion not required on any vehicles that I looked at before contacting you. If the brake pedal IS pushed down even slightly from the right hand side/edge of the brake pedal (normal habit by most drivers reviewing wear patterns on brake pedals of many vehicles at my office complex) the bottom of a man's right shoe will almost always be somewhat over the accelerator, and the potential for dual/simultaneous brake and accelerator pushing IS created. *js
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11008948While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10241547Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
- 10205022Torqshift Transmission - Malfunction indicator lamp (MIL) diagnostic trouble codes (DTCS) P0751, P0730 and/or P2700
- 102049974R75E Transmission - Grinding/Whine/Vibration/Gear Slippage - Serrvice Kit available
- 10183758Some 2009-2016 E-Series, F-Super Duty, 2009-2015 F-53 Motorhome and 2011-2015 F-59 Stripped Chassis vehicles equipped with a TorqShift transmission and a transmission built on or before 12/15/2015 may exhibit a MIL with DTCs P0751, P0730 and/or P2700
- 10164508Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
- 10164497For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
- 10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
- 10159489Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10155574Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
- 10138524The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10127405Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
- 10095154To help differentiate engine oil leaks from other possible sources, a new white-colored fluorescent engine oil dye IS available. Workshop manual (wsm), section 303-00 has been revised to reference the new white-colored dye. The new white fluorescent dye provides a distinct white glow to identify engine oil leaks. The new white fluorescent dye requires a pure uv diagnostic inspection lamp. The white-colored fluorescent dye and pure uv lamp are now in the rotunda catalog. Dye and lamp part numbers. Gasoline only dye: 1 ounce bottle 164-tp-33200601. Diesel only dye: 8 ounce bottle: 164-tp-3320-0008. Pure uv diagnostic inspection lamp 164-tp8695 or 164-r3748.
- 100810132009-2016 e-series difficulty programing trailer brake control (tbc) module.
- 100752624R75E TRANSMISSION - GRINDING/WHINE/VIBRATION/GEAR SLIPPAGE - SERVICE KIT AVAILABLE ISSUE A service kit has been released to assist with proper repair of the 4R75E transmission in 2008 Mark LT, 2008-2010 F-150, 2008-2010 / 2013-2014 E-Series, 2008-2011 Crown Victoria, Grand Marquis and Town Car vehicles that exhibit a grinding, whine-type noise, vibration and/or gear slippage while driving, or a loss of reverse resulting from a planetary gear assembly failure.
- 10057834Ford: no service action IS recommended for this condition. Please use at your discretion. Various 2010-2015 vehicles may experience a turbulence noise, similar to an helicopter noise, at highway speeds when the rear door window(s) or sunroof are open.
- 10056196Ford: when shifting between park, reverse and/or during 2-3 shift, an intermittent clunk occurs with a torqshift transmission. Model 2003-2014 f-super duty, e series, excursion, F-53 motorhome chassis, low cab forward.
- 10055312Ford: some model vehicles manual for powertrain control/emission diagnostic (pc/ed) has been updated regarding improved cooling fan circuit due to a lack of air conditioning, a malfunctioning indicator lamp (mil) and overheating.
Every Ford E-150 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.