2011 Ford F-450 SD
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Ford › F-450 SD › 2011
These records cover every 2011 Ford F-450 SD. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2011 Ford F-450 SD. Newest first.
Ford Motor Company (Ford) is recalling certain model year 2011-2015 Ford F-350, F-450, and F-550 trucks manufactured February 22, 2010, to January 30, 2015, and equipped with ambulance or fire engine preparation packages. The affected vehicles may detect an incorrect Exhaust Gas Temperature Sensor (EGT) fault indicating that the vehicle is too hot…
Risk and remedy
Risk
Engine shut down and a subsequent cool down period may delay medical treatment or assistance to those needing it, increasing their risk of injury.
Remedy
Ford will notify owners, and dealers will update the Powertrain Control Module (PCM) software, free of charge. The recall began on April 22, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S09.
Palfleet Truck Equipment Company, LLC (Palfleet) is recalling certain model year 2009-2013 Ford F-350, F-450, and F-550 super duty vehicles modified by Palfleet and equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Risk and remedy
Risk
The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy
Palfleet will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began on July 29, 2014. Owners may contact Palfleet customer service at 1- 502-376-2458.
Iowa Mold Tooling Co., Inc. will notify owners and dealers to inspect the Muncie PTO pressure switch to determine if it is from the range of defective switches and if required, remove the pressure switch assembly and put a plug in the port where the PTO switch had been installed. This switch was never being utilized. This will be done free of charge. The…
Risk and remedy
Risk
The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy
Iowa Mold Tooling Co., Inc. will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began on July 28, 2014. Owners may contact Iowa Mold Tooling Co., Inc. at 1-800-247-5958.
Stahl is recalling certain model year 2009-2014 Ford F-350 Super Duty, F-450 Super Duty, and F-550 Super Duty vehicles modified by Stahl and equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Risk and remedy
Risk
The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy
Stahl will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. Owners may contact Stahl customer service at 1-800-277-8245, or Muncie at 1-800-367-7867.
Utility Truck Equipment Company, LLC (Utility Truck) is recalling certain model year 2010-2013 UTLI41A, 2011 UTLN41, and 2012 UTLN46 aerial trucks manufactured December 2010 to September 2013 equipped with certain Muncie Power Products PTO Assemblies installed on 2010-2013 Ford F-350, F-450 and F-550 vehicles. In the affected vehicles, oil may leak from…
Risk and remedy
Risk
The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy
Utility Truck will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began in June 2014. Owners may contact Utility Truck customer service at 1-254-857-8813.
Somerset Welding & Steel, doing business as J&J Truck equipment (J&J), is recalling certain model year 2009-2013 Ford F-350, F-450, and F-550 Super Duty chassis with 6.8L gasoline engines modified by J&J to be equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal…
Risk and remedy
Risk
The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy
Somerset will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began August 2014. Owner's may contact Somerset customer service at 1-800-777-2671.
Ford IS recalling certain model year 2011 ford F-150, F-250, F-350, F-450, F-550, edge, and lincoln MKX trucks manufactured from october 25, 2010, through november 20, 2010. these vehicles were inspected using integrated diagnostic system (ids) that had a custom software routine to read the suspect body control module (bcm) serial number. Based on the…
Risk and remedy
Risk
If an electrical short develops, an overheating condition may occur which could result in a vehicle fire.
Remedy
Dealer will inspect the body control module and if necessary replace it free of charge. the safety recall began on march 7, 2011. owners may contact ford motor company customer relationship center at 1-866-436-7332.
Ford IS recalling certain model year 2011 F-150, F-250, F-350, F-450, F-550, edge and lincoln MKX vehicles. during a six-day production period, the supplier of the body control module manufactured modules that may have the potential for an internal short.
Risk and remedy
Risk
If an electrical short develops, an overheating condition may occur which can result in an unattended vehicle fire.
Remedy
Dealer will replace the body control module if necessary free of charge. the safety recall began on january 11, 2011. owners may contact ford at 1-866-436-7332.
Owner complaints
6 complaints1 involved a fire
What owners report most
Latest complaints
- Engine · Power train · Vehicle speed control
When traveling down the hiway,sometimes you will lose power. you will feel a jerk. the engine IS still running but no power to the wheels. pretty scary when you are trying to pass a vehicle on the interstate. you try to pull over to the side of the road. you have no means of movement. you can…
When traveling down the hiway,sometimes you will lose power. you will feel a jerk. the engine IS still running but no power to the wheels. pretty scary when you are trying to pass a vehicle on the interstate. you try to pull over to the side of the road. you have no means of movement. you can now turn off the vehicle and put it in neutral and restart the engine,you can now continue down the hiway until it happens again. this has happened multiple times. we have driven with our horse trailer down to arizona 3 times and this has happened 3-4 times each way. ford dealer where purchased has no clue what IS causing this. this vehicle was purchased brand new. we have had this problem since new.
- Fuel/propulsion system
6.7 diesel fuel injector hold down clamp broke and fuel injector blew out of cylinder head spraying fuel all over engine compartment. vehicle was always serviced by authorized ford dealers per schedule. Vehicle in motion on highway. Has 98,000 miles on it, but IS a few months over the 5 year…
6.7 diesel fuel injector hold down clamp broke and fuel injector blew out of cylinder head spraying fuel all over engine compartment. vehicle was always serviced by authorized ford dealers per schedule. Vehicle in motion on highway. Has 98,000 miles on it, but IS a few months over the 5 year powertrain warranty. local ford tech says its a common problem for this engine, and ford has recognized it and IS making engineering changes to replacement parts. This may be, but having a high pressure fuel system blow apart on the road IS not common for me. And of course no warranty coverage so I have to cover all costs. I have no notification from anyone about recalls or tsbs effecting the vehicle.
- Engine
TL* the contact owns a 2011 ford F-450 sd. While driving at any speed, the vehicle stalled without warning and the service engine warning light illuminated. The vehicle was able to restart. The failure recurred numerous times. The dealer diagnosed that the turbo needed to be replaced. The vehicle…
TL* the contact owns a 2011 ford F-450 sd. While driving at any speed, the vehicle stalled without warning and the service engine warning light illuminated. The vehicle was able to restart. The failure recurred numerous times. The dealer diagnosed that the turbo needed to be replaced. The vehicle was repaired, but the failure recurred a week later. The vehicle was not included in nhtsa campaign number: 10v659000 (structure). The manufacturer was made aware of the failure. The failure mileage was 77,000.
- Fuel/propulsion system · Service brakes · Steering
Truck was pulling my 16K 5TH wheel camper over the passes between montana and idaho in tow haul mode up and down. These are only 4,200 foot passes but steep. Usually in 6TH gear but sometimes 4TH going 50-55; oil temps show as 220 to 239 then the big fan kicks in to cool it. on one of the…
Truck was pulling my 16K 5TH wheel camper over the passes between montana and idaho in tow haul mode up and down. These are only 4,200 foot passes but steep. Usually in 6TH gear but sometimes 4TH going 50-55; oil temps show as 220 to 239 then the big fan kicks in to cool it. on one of the smaller passes, shortly after I crested the hill the truck sharply down shifted (i think it skipped 4TH and went into 3RD. Immediately thereafter the "check engine" light came on, ?tool? Emblem showed on dash, "low power" notice showed on dash, and I barely had time to get halfway off the road before I lost power steering and brakes. This could have been a horrific disaster on just about any other interstate highway location, let alone two lane roads that we have been with our truck/trailer. As it was, it was one very scary ten seconds. I had no power steering or brakes. later I learned that if it happens again that I should keep it above 5 mph to get off road and lined up, then stomp on brakes because you only have one chance. on the side of the road, "?check engine" light IS red, but no other warning lights now. I can get no revs out of engine. I turn off key and shut down. Check fluids underneath, and under hood all IS well. Try phone - no coverage. Closest town IS 16 miles. restart engine after 5 minutes. it was about 60 outside at the top of the pass, and I can now rev engine, but engine light IS on. Head to town, get cell coverage on next rise and call ahead to nearest ford dealer for directions. another pass IS between us - 4TH of july, a taller one than the shutdown event. idaho dealer ([xxx], lake city ford) kindly squeezes me in. See engine light on. Tech [xxx] sees light and runs scan and sees no record of any codes in any systems. What the?? Next morning, ford told dealer that there IS no way that a code did not register if the light was on. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *tr
- Engine and engine cooling › Engine › Diesel · Engine and engine cooling › Exhaust system
TL* the contact owns a 2011 ford F-450 sd. The contact stated while driving approximately 55 mph the engine stalled with an illumination of the warning indicator. The vehicle failed to restart and was towed to an authorized dealer for diagnostic testing. The failure was contributed to a faulty egt…
TL* the contact owns a 2011 ford F-450 sd. The contact stated while driving approximately 55 mph the engine stalled with an illumination of the warning indicator. The vehicle failed to restart and was towed to an authorized dealer for diagnostic testing. The failure was contributed to a faulty egt exhaust temperature sensor. The vehicle was repaired. The manufacturer was notified of the problem. The approximate failure mileage was 82,500. *tr
- Engine and engine cooling
Vehicle fire. the vehicle and all warning lights were off when the fire started. updated 03/21/12 *bf updated 04/30/12*bf updated 05/09/12 *bf updated 05/12/2012 *js
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Vehicle Commanded Engine Shutdown
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package…
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10249483Certain 2011-2012 Model Year F-Series Super Duty Vehicles Equipped with a 6.7L Diesel Engine State Inspection and Maintenance Test Failure Due to DTCs P2073 and/or P2074 Adding owner letter and corrected dealer bulletin. First Part submitted 11/01/23
- 10248068Certain 2011-2012 Model Year F-Series Super Duty Vehicles Equipped with 6.7L Diesel Engine State Inspection and Maintenance Testing Failure Due to DTCs P2073 and/or P2074
- 10244684Customer Satisfaction Program 22N14 Supplement #1 Certain 2011-2012 Model Year F-Series Super Duty Vehicles Equipped with a 6.7L Diesel Engine - State Inspection and Maintenance Test Failure Due to DTCs P2073 and/or P2074
- 102377892011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26C (80F) and may increase to 1200 RPM at -40 C (-40F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
- 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
- 10228867Some 2011-2022 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 F (65 C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
- 10222521Certain 2011-2012 Model Year F-Series Super Duty Vehicles Equipped with a 6.7L Diesel Engine Powertrain Control Module Reprograming for Inspection and Maintenance Testing
- 10211955Certain 2011-2014 Model Year Super Duty Vehicles Equipped with a 6.7L Diesel Engine Exhaust Gas Recirculation Cooler with Diagnostic Trouble Codes P0401 and/or P2457 - In some of the affected vehicles, customers may experience an illuminated malfunction indicator light due to the EGR cooler becoming plugged with hydrocarbon or soot at high mileage. Diagnostic trouble codes (DTCs) for EGR cooler efficiency below threshold (DTC P0401) and/or insufficient EGR flow at idle (DTC P2457) are stored when the malfunction indicator light is illuminated.
- 102093842011-2022 F-Super Duty and 2016-2023 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26C (80F) and may increase to 1200 RPM at -40 C (-40F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
- 10209377Some 2011-2012 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P2073 and/or P2074 stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.
- 10206863Customer Satisfaction Program 21M04 Certain 2011-2014 Model Year Super Duty Vehicles Equipped with a 6.7L Diesel Engine Exhaust Gas Recirculation Cooler with Diagnostic Trouble Codes P0401 and/or P2457
- 10205475Some 20112014 F-Super Duty vehicles equipped with 6.7L diesel engine may experience an exhaust leak due to broken exhaust manifold studs. New parts have been released to service this condition. Replace the exhaust manifold on the side with a broken stud. On cylinders 1,2,3,5,6 and 7 use stud part number W715713-S431. If replacing the studs on cylinders 4 and/or 8 use stud part number W717172-S900 and replace both studs and install new spacers and heat shields on the affected side(s). Refer to Workshop Manual, Section 303-01. Part numbers: heat shield left side, FC3Z-9Y427-A and DC3Z-9A462-B for the right side. Spacer part number FC3Z-00810-A. Exhaust manifold part numbers: DC3Z-9430-A (right) and DC3Z-9431-A (left). Exhaust Manifold Gasket FC3Z-9448-A. Exhaust Manifold Nut W701706-S430.
- 102050296.7L Diesel - fuel knock at idle with malfunction indicator lamp (MIL) Illulminated with multiple diagnostic trouble codes (DTCS)
- 10205022Torqshift Transmission - Malfunction indicator lamp (MIL) diagnostic trouble codes (DTCS) P0751, P0730 and/or P2700
- 102050146.7L Diesel - Fuel knock at idle with malfunction indicat or lamp (MIL) Illuminated with multiple diagnostic trouble codes (DTCSF)
- 102049996.7L Malfunction indicator Lamp (MIL) Illuminatedc with diagnostic trouble codes (DTCS p208E, p218F, p204F
- 1020498749 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C
- 1020498649 CFR Part 579.5 Monthly Communications - January 2016
- 10204983Exterior Mirror - Tubular stainless steel west cpast style mirror - Loose mounting bracket
- 10194421Some 2011-2021 vehicles equipped with a diesel engine may have engine oil in the exhaust after turbocharger replacement for various reasons. To correct the condition, remove the exhaust and stand the exhaust up with the turbocharger inlet side facing down using a suitable drain pan. Allow the exhaust to drain for at least 24 hours and reinstall. Do not perform a manual exhaust regeneration.
- 10186678Some 2005-2021 F-Super Duty 4x4 vehicles operated in extreme dust, mud or tar sand conditions may exhibit accelerated 4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet
- 101865672011-2021 F-Super Duty and 2016-2021 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit a high/elevated idle condition. During prolonged idle time, vehicles may experience this high/elevated idle to reduce buildup of unburned hydrocarbons from the SCR system. The powertrain control module (PCM) estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 revolutions per minute (rpms) for ambient temperatures near 26C (80F) and may increase to as high as 1200 rpms at -40 C (-40F). These elevated idle periods can last from 20-40 minutes, depending on ambient temperatures. During power take off (PTO) use and already using idle set point control, the elevated speed is disabled. It is required that the operator monitor the vehicle and adhere to the Exhaust Filter warning messages.
- 10179325Some 2011-2020 F-Super Duty, 2015-2019 Transit, 2016-2021 F-650/F-750 and 2018-2020 F-150 vehicles equipped with a 6.7L, 3.2L or 3.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P207F, P20EE, P229F, P2201 and/or P24AE. This may be a result of using aftermarket cleaning liquids or tools for the exhaust gas recirculation (EGR) cooler or intake. Ford does not recommend the cleaning of diesel intakes or EGR coolers using any aftermarket tool that injects a cleaning foam or liquid substance into the EGR cooler or intake. Using these types of fluids can result in sodium poisoning of the NOx and particulate matter (PM) sensors resulting in degraded operation and permanent damage to the after treatment system. Use of these cleaning tools may void the emissions warranty of the hot end after treatment exhaust system and the attached emissions sensors.
- 10170992Some 2005-2020 F-Super Duty 4x4 vehicles operated in extreme dust, mud or tar sand conditions may exhibit accelerated 4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet
- 10164598Some remanufactured 6.7L diesel engines recently installed in 2011-2014 F-Super Duty vehicles may exhibit a lack of power with engine oil temperature (EOT) exceeding 125C (257F) under loads. This may also be accompanied by REDUCED ENGINE POWER being displayed in the message center and the coolant temperature gauge indicating H. This symptom may be due to a missing metering cup plug in the upper oil pan causing reduced oil flow through the oil cooler. Remanufactured engines built on 1-Mar-2019 and through 13-May-2019 may be affected. If a vehicle exhibits this concern, use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Include the engine serial number and engine build date in the report. The dealership may be contacted for further details and possible repair direction.
- 10164508Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
- 10163595Customer Satisfaction Program 18M05 Certain 2011-2012 Model Year F-450 and F-550 Vehicles Equipped with a 6.7L Engine Turbocharger Extended Warranty Coverage
- 10162082Some 2011-2019 F-Super Duty vehicles equipped with a 6.7L engine may come in for scheduled maintenance on the engine mounted fuel filter. When reconnecting a fuel line quick connect fitting back onto the engine mounted fuel filter housing, push the connector all the way onto the fuel filter connection port. For some vehicles, you may need to depress a retainer clip to lock the quick connect port into place. Once the fitting is latched fully onto the connection port, pull straight backward on the fuel line to verify it is fully latched onto the connection port. Do not bend the fuel line connection when pulling to verify it is connected. Refer to Workshop Manual sections 310-00 for details on quick connect fittings.
- 10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
- 10160885Some 2005-2019 F-Super Duty 4x4 vehicles operated in extreme dust, mud or tar sand conditions may exhibit accelerated 4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet
- 10160871Some 2011-2016 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a lack of power and/or illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0299 in the powertrain control module (PCM). This may be due to the charge air cooler (CAC) outlet tube assembly becoming disconnected at the throttle body or a separation at the CAC tube crimp clamp. To resolve this concern, follow the Service Procedure steps to replace the CAC outlet tube assembly.Follow the service procedure steps to correct the condition.
- 10159494SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
- 10156889Some 2011-2019 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking/tapping noise traced to the reductant injector.
- 10155577Some 2011-2019 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking/tapping noise traced to the reductant injector.
- 10153984Certain 2011-2012 Model Year 6.7L F-450-F-550 Chassis Cab Vehicles Over 14K GVWR - NOx Sensor Extended Warranty Coverage
- 10152467Some 2011-2019 F-Super Duty, 2015-2019 Transit, 2016-2019 F-650/F-750 and 2018 F-150 vehicles equipped with a 6.7L, 3.2L or 3.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P207F, P20EE, P229F, P2201 and/or P24AE. This may be a result of using aftermarket cleaning liquids or tools for the exhaust gas recirculation (EGR) cooler or intake. Ford does not recommend the cleaning of diesel intakes or EGR coolers using any aftermarket tool that injects a cleaning foam or liquid substance into the EGR cooler or intake. Using these types of fluids can result in sodium poisoning of the NOx and particulate matter (PM) sensors resulting in degraded operation and permanent damage to the aftertreatment system. Use of these cleaning tools may void the emissions warranty of the hot end aftertreatment exhaust system and the attached emissions sensors.
- 10148818This SKU is a front upper ball joint. The Customer communication requested return of unsold inventory to inspect for ball studs with excessive rotational friction in the ball joint assembly. Excessive friction in the ball joint assembly may cause a perceptible increase in steering effort.
- 10144202When performing diagnostics for DTCs P2201, P2452, P2459, P246C and/or P2463, a manual regeneration and diesel particulate filter (DPF) parameter reset using the appropriate scan tool may need to be performed. To perform the manual regeneration, go to the Toolbox tab > Powertrain > Service Functions > Diesel Particulate Regeneration System > DPF Manual Regeneration. The scan tool may indicate that a regeneration of the DPF is not recommended at this time, selecting YES on this screen will allow the regeneration process to complete. To perform the DPF parameter reset, go to the Toolbox tab > Powertrain > Service Functions > Diesel Particulate Regeneration System > DPF Parameter Reset.
- 10140328Some 2011-2018 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 ?F (65 ?C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
Every Ford F-450 SD model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.