2015 Ford Fiesta
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Ford › Fiesta › 2015
These records cover every 2015 Ford Fiesta. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2015 Ford Fiesta. Newest first.
Ford Motor Company (Ford) is recalling certain 2015 Fiesta, 2016 Fusion, and 2016 Lincoln MKZ vehicles sold, or ever registered in Alabama, Arkansas, Arizona, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, New Mexico, Nevada, Oklahoma, Oregon, South Carolina, Texas, Utah, Washington, Puerto Rico, American Samoa, Guam, the Northern Mariana…
Risk and remedy
Risk
Vehicle doors opening unexpectedly while driving can increase the risk of a crash or injury.
Remedy
Dealers will inspect the door latch date codes and if necessary, replace all four side door latches, free of charge. Owner notification letters were mailed December 20, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S15. This recall is an expansion of NHTSA recall number 20V-177.
Ford Motor Company (Ford) is recalling certain 2014-2015 Fiesta, 2014-2016 Fusion and Lincoln MKZ vehicles sold, or ever registered in Alabama, Arkansas, Arizona, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, New Mexico, Nevada, Oklahoma, Oregon, South Carolina, Texas, Utah, Washington, Puerto Rico, American Samoa, Guam, the Northern Mariana…
Risk and remedy
Risk
A door that is not securely latched could open while the vehicle is in motion, increasing the risk of injury to a vehicle occupant.
Remedy
Ford will notify owners, and Ford or Lincoln dealers will replace the side door latches, free of charge. The recall began September 21, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S15.
Ford Motor Company (Ford) is recalling certain 2014 Escape, 2014-2015 Fiesta ST, 2013-2014 Fusion and 2013-2015 Transit Connect vehicles equipped with 1.6L GTDI engines. If the vehicle is started and driven with an insufficient level of coolant within the engine cooling system, the engine cylinder head may overheat, crack and leak oil.
Risk and remedy
Risk
If the cylinder head cracks and leaks oil, the oil may contact a hot engine or exhaust component, increasing the risk of a fire.
Remedy
Ford will notify owners, and dealers will install a coolant level sensor and the supporting hardware and software, free of charge. Interim notices informing owners of the safety risk were mailed April 21, 2017. The recall began on January 5, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S09.
Ford Motor Company (Ford) notified the agency on January 8, 2015, that they are recalling certain model year 2014 Ford Escape vehicles manufactured April 15, 2014, to May 8, 2014, and 2015 Lincoln MKC vehicles manufactured April 21, 2014, to May 15, 2014. On April 30, 2015, Ford expanded the recall to cover an additional 45,505 vehicles, including certain…
Risk and remedy
Risk
If the fuel pump fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will replace the fuel pump, free of charge. The recall began on February 27, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S30.
Owner complaints
259 complaints16 involved a crash24 injuries
What owners report most
Latest complaints
- Electrical system · Power train · Vehicle speed control
Vehicle turned off on highway, jerks while shifting, and transmission hot light turns on
- Fuel/propulsion system
Car sputters everytime I put gas in it. Sometimes shuts off. It’s every time I put gas. I’m not filling up the gas tank because I notice if I do fill it up. It gives me more problems .. occurring problem
- Power train
The contact stated that the vehicle was taken to the dealer for recall repairs; however the issue persisted. After the repairs, while mother was driving on the highway, the vehicle stalled. The clutch became inoperable. The vehicle was towed to the residence. The vehicle was not further diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 20,000.
- Engine
I have taken the vehicle to 2 auto places both have confirmed it has engine failure. It only has 140,000 miles
- Electrical system · Suspension · Unknown or other
I was driving on the highway, and my car started shaking. All of the sudden I couldn't push on the gas anymore, and out of the blue a notification popped up on my screen that said "transmission failure, service immediately" and the car fully stopped working. I was forced to coast to the side of the…
I was driving on the highway, and my car started shaking. All of the sudden I couldn't push on the gas anymore, and out of the blue a notification popped up on my screen that said "transmission failure, service immediately" and the car fully stopped working. I was forced to coast to the side of the highway, where I ended up in an incredibly dangerous spot. I had to call the cops, have them come so I wouldn't get hit (it was fully night time), and had to wait for a tow truck to come tow me and my car off the side of the highway.
- Engine · Power train · Steering
I was driving for couple hours then my oil light came on check engine light came on. Vehicle started to shake very badly. I had to pull over and see what happened. I started the vehicle up again and the oil light and check engine light are still on. I know that these vehicles have the wet belt…
I was driving for couple hours then my oil light came on check engine light came on. Vehicle started to shake very badly. I had to pull over and see what happened. I started the vehicle up again and the oil light and check engine light are still on. I know that these vehicles have the wet belt system on the automatics. But they don't have one for the manual transmission. There should be a recall for these just like the automatics.
- Electrical system · Engine · Power train
No
- Power train
Transmission going out with car having only 71,000 miles on it .a know fact that Ford knew when I bought this car new .and going out when on freeways or just about anywhere could me in danger
- Engine
Low pressure oil light came on and I stopped driving it 18 miles later drove about 25-30 mph hoping it wouldn’t seize on me before I got home. because I figure the oil pump is clogged with timing belt fragments and I can’t afford to replace the timing belt right now. Afraid to drive it because I…
Low pressure oil light came on and I stopped driving it 18 miles later drove about 25-30 mph hoping it wouldn’t seize on me before I got home. because I figure the oil pump is clogged with timing belt fragments and I can’t afford to replace the timing belt right now. Afraid to drive it because I have read it could seize up the engine. 1.0 eco boost manual transmission. Car ran great and I had no issues with it until the low pressure oil light came on. Been sitting since March. I have started it 4 times since then and it has been moved around the yard but never ran longer than a few minutes. Still starts just afraid with the low pressure oil light on that it could seize up if I drive it again.
- Engine
This vehicle has experienced the exact issue of a Ford recall for other model year fiestas. The oil pump belt has experienced premature wear and failure, leading to a sudden loss of power. My local Ford dealer says that this vehicle should have been included in Ford recall #23S64 and that I should report this to NHTSA to document and hopefully expand the recall to all years that result in this issue.
- Power train
The contact owns a 2015 Ford Fiesta. The contact stated that while attempting to start the vehicle, the vehicle failed to start as expected. The check engine warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with the Transmission Control…
The contact owns a 2015 Ford Fiesta. The contact stated that while attempting to start the vehicle, the vehicle failed to start as expected. The check engine warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with the Transmission Control Module. The contact was informed that the TCM needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 140,000.
- Power train
The contact owns a 2015 Ford Fiesta. The contact stated that after the battery was replaced, the message "Transmission Malfunction Service Now" message was displayed on the instrument panel. The contact stated that while driving at various speeds, the RPMs fluctuated, and the engine revved…
The contact owns a 2015 Ford Fiesta. The contact stated that after the battery was replaced, the message "Transmission Malfunction Service Now" message was displayed on the instrument panel. The contact stated that while driving at various speeds, the RPMs fluctuated, and the engine revved abnormally. Whenever the contact attempted to depress the brake pedal, the engine jerked, and the transmission failed to shift as intended. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. Upon investigation, the contact related the failure to the Customer Satisfaction Program: 14M02 (Transmission Control Module); however, the VIN was not included. The failure persisted, and the vehicle remained at the residence unrepaired. The contact had parked the vehicle out of safety concerns. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 199,000.
- Power train
Malfunction of automatic transmission module.reverse not engaging.slipping of gears while operating.diagonisis confirmed at peoria ford peoria az on 8/25.4 weeks after warranty expired!!!!!!!!!! Check engine light at time of malfunction.very dangerous situation not able to control auto !!!!!!!!!!!!!!!!!!!!
- Power train
The contact owns a 2015 Ford Fiesta. The contact stated that the vehicle failed to start, and upon jumpstarting the vehicle, the message "Transmission Failure - Service Now" was displayed. The vehicle was taken to an independent mechanic, who informed the contact that the VIN was included in an…
The contact owns a 2015 Ford Fiesta. The contact stated that the vehicle failed to start, and upon jumpstarting the vehicle, the message "Transmission Failure - Service Now" was displayed. The vehicle was taken to an independent mechanic, who informed the contact that the VIN was included in an unknown recall, and the contact was referred to the dealer for assistance. The vehicle was taken to the dealer, where the contact was informed that the recall had expired. The dealer replaced the TCM at the contact's expense. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 125,000. The VIN was not available.
- Power train
The contact owns a 2015 Ford Fiesta. The contact stated that while driving at various speeds, the engine jerked while depressing the accelerator pedal. The contact stated that the "Engine Malfunction Service Now" message was displayed on the instrument panel at start up. The vehicle was taken to…
The contact owns a 2015 Ford Fiesta. The contact stated that while driving at various speeds, the engine jerked while depressing the accelerator pedal. The contact stated that the "Engine Malfunction Service Now" message was displayed on the instrument panel at start up. The vehicle was taken to dealer where the contact was provided an estimate for the repair. Upon investigation, the contact discovered that the vehicle was included in Customer Satisfaction Program: 14M02 (Transmission control module extended warranty coverage); however, the dealer refused to honor the warranty. The manufacturer was notified of the failure but provided the same information as the dealer. The vehicle was not repaired. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was approximately 45,000.
- Power train
The contact owns a 2015 Ford Fiesta. The contact stated while driving 65 MPH, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. In addition, the check engine warning light was illuminated. The contact drove the vehicle to the shoulder of the road and turned…
The contact owns a 2015 Ford Fiesta. The contact stated while driving 65 MPH, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. In addition, the check engine warning light was illuminated. The contact drove the vehicle to the shoulder of the road and turned off the vehicle. The contact stated that the vehicle was restarted, and after several attempts, the vehicle started. The vehicle was driven to the residence. The dealer was made aware of the failure but provided no assistance. The vehicle was taken to an independent mechanic, where it was diagnosed with TCM failure. The manufacturer was made aware of the failure but provided no assistance. The contact was informed of an unknown recall for the TCM however, the recall had expired. The contact had not received a recall notification. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 120,000.
- Engine
In May, my 2015 Ford Fiesta SE went into "limp mode" before reaching the speed limit of 25mph. Immediately afterwards it was taken into a local shop, Mobile Mechanic, where no codes were active and coolant level was between min and max level. Next day, car experienced misfiring check engine light…
In May, my 2015 Ford Fiesta SE went into "limp mode" before reaching the speed limit of 25mph. Immediately afterwards it was taken into a local shop, Mobile Mechanic, where no codes were active and coolant level was between min and max level. Next day, car experienced misfiring check engine light and overheating before being looked at by a mechanic. Mechanic replaced spark plugs due to code reading misfiring in cylinder 3. Car still continued to misfire and due to slight lower level of coolant, Engine overheated and cracked a cylinder block in the 1.0-liter three-cylinder EcoBoost engine. This car is used to travel with two children under [XXX] and [XXX]. The beginning of June the car overheated on a hot day traveling home with the two kids and myself. We had to sit in the heat for close to an hour before temperature gauge returned to normal, I checked the coolant and it was still between min and max levels. On the same trip, it was on the verge of overheating again due to climbing the hill before our house. After finding out the cylinder block was cracked by my mechanic we discovered there has been a recall issue with the same engine, Recall 17S09, that began in January 2018, a month before I purchased my car from Redwood Ford in Ukiah California ([XXX]). I called W. C. Sanderson Ford in Healdsburg, California on July, 15th, 2025 to see if it would be possible to see if this recall was actually fixed on my vehicle, which they responded that the recall has nothing to do with my car and they can't do anything about my car. The representative specifically said that due to my car being 10 years old it has been disqualified of the recall and is no longer attached to my VIN. I have taken this car to the same local mechanic 4 times since the ending of May, 2025 for the same issues before we discovered the cracked cylinder block, mechanic took pictures of fluid and water inside cylinder 3. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine
In 2020, Documents were subpoened proving that Ford falsified doors and used a dangerous faulty transmission in Ford Fiesta and Focus Moodels from 2011-2015. There were so many lawsuits, they settled through arbitration. The judicial system only required an extended waranty- no recall or redesign.…
In 2020, Documents were subpoened proving that Ford falsified doors and used a dangerous faulty transmission in Ford Fiesta and Focus Moodels from 2011-2015. There were so many lawsuits, they settled through arbitration. The judicial system only required an extended waranty- no recall or redesign. These vehicles are dangerous, and when transmission overheats, the cars stop in the middle of the road. Many will not go in Reverse. Ford is recouping their arbitration settlement money by continuing to sell these cars on the Used Car Market with the same DPS6 Transmissions which they knew were faulty and dangerous, and falsified documents about, with Clean Car Faxes, often low mileage- because heat starts transmission failure, and that is not fair. The pledge does not say...."WitH liberty and justice for ALL WHO CAN AFFORD IT!" I HAVE AMOST BEEN REAR-ENDED TWICE, because car stops when Trans gets hot. One driver of a 4'4 truck, speeding around a blind spot, swerved into oncoming lane, rolled down his window, pointed a pistol at me, cursing because I ALMOST made HIM WRECK! although my safety flashers were on. There are no shoulders on these rural roads. This car is DANGEROUS! WHY WAS FORD ALLOWED TO GET AWAY WITH THIS? Falsification of documents about a cars safety is fraud. There are tens of thousands with Clean Car Faxes still being sold unfairly to unknowing victims with modest incomes who TRUST CAR FAX DOCUMENTATION.
- Power train
The transmission control module (TCM) on my 2015 Ford Fiesta was failing at 81,000 miles. It was difficult to accelerate the car even at low speeds (25-30 mph) and my check engine light was on. I took my vehicle to the nearest Ford Dealership (Big Star Ford in Manvel, TX) who assessed my vehicle…
The transmission control module (TCM) on my 2015 Ford Fiesta was failing at 81,000 miles. It was difficult to accelerate the car even at low speeds (25-30 mph) and my check engine light was on. I took my vehicle to the nearest Ford Dealership (Big Star Ford in Manvel, TX) who assessed my vehicle and determined the TCM needed to be replaced. They replaced the part but told me it was not under the 14M02 warranty. My check engine light did come on once back in May and the car was struggling to speed up but when I took it to a car shop the check engine light was not on and the mechanic said it was fine.
- Power train › Automatic transmission › Control module (tcm/pcm/tecm)
The contact owns a 2015 Ford Fiesta. The contact stated that while operating the vehicle, the check engine warning light illuminated, and the vehicle failed to properly accelerate while depressing the accelerator pedal. The vehicle was taken to the local O'Reilly's and was diagnosed with…
The contact owns a 2015 Ford Fiesta. The contact stated that while operating the vehicle, the check engine warning light illuminated, and the vehicle failed to properly accelerate while depressing the accelerator pedal. The vehicle was taken to the local O'Reilly's and was diagnosed with transmission failure. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the VIN was not eligible for Customer Satisfaction Program: 14M02 (Extended Warranty Coverage for TCM) related to the failure. The failure mileage was 79,000.
- Engine
There is a recall (Recall no. 17V209000) that my VIN should have been included in but is not. My vehicle was not equipped with a coolant level sensor from the factory and does not alert to low coolant levels in the vehicle, which can lead to overheating, engine damage, and potential engine fire.…
There is a recall (Recall no. 17V209000) that my VIN should have been included in but is not. My vehicle was not equipped with a coolant level sensor from the factory and does not alert to low coolant levels in the vehicle, which can lead to overheating, engine damage, and potential engine fire. The recall fix is a new updated coolant tank design, the inclusion of a coolant level sensor, and a software update for the function of said sensor.
- Unknown or other
the manufacture have fixed the car the recall yesterday.
- Electrical system · Engine
The contact's wife owns a 2015 Ford Fiesta. The contact stated that while the vehicle was idling or driving below 20 MPH, the vehicle sputtered and then shut off with the battery and check engine warning lights flashing on the instrument panel. The vehicle was taken to an unknown dealer, where the…
The contact's wife owns a 2015 Ford Fiesta. The contact stated that while the vehicle was idling or driving below 20 MPH, the vehicle sputtered and then shut off with the battery and check engine warning lights flashing on the instrument panel. The vehicle was taken to an unknown dealer, where the contact was informed that there were no recalls on the VIN. The contact asked for an estimate for a diagnostic test but was denied service. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The manufacturer then referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 112,000.
- Engine
On 3/10/2025, when driving my 2015 Ford Fiesta SE, I experienced a sudden failure consisting of a "lurch", lost all drive power to the vehicle, and had to use inertia to steer myself out of traffic to the shoulder of the road. After exiting the vehicle, I inspected all tires (no issues) and popped…
On 3/10/2025, when driving my 2015 Ford Fiesta SE, I experienced a sudden failure consisting of a "lurch", lost all drive power to the vehicle, and had to use inertia to steer myself out of traffic to the shoulder of the road. After exiting the vehicle, I inspected all tires (no issues) and popped the hood (no visible issues like smoke). I requested emergency roadside assistance to tow my vehicle to the nearest mechanic shop. After troubleshooting the vehicle, the shop confirmed that all fluid levels were okay and the timing belt had failed, specifically noting that the manufacture-recommended PMI is at 150,000 miles and my vehicle only had 118,579 miles. What component failed = Timing belt. Is it available for inspection = It can be. How was safety at risk = Losing all mechanical power while going up a grade in heavy traffic. Has the problem been confirmed = Yes, by an independent service center. Has the vehicle been inspected by the manufacturer, police, or insurance = No, but I did call Ford's service line to notify them; no action taken on their part. Any warnings = No sounds, no transient loss of power, no warning lights; just a sudden "bang" and "lurch".
- Engine and engine cooling
The contact owns a 2015 Ford Fiesta. The contact stated that during cold weather conditions, the check engine and the low oil pressure warning lights illuminated intermittently. The failure had become constant over time. The contact who is a certified mechanic, diagnosed the vehicle and determined…
The contact owns a 2015 Ford Fiesta. The contact stated that during cold weather conditions, the check engine and the low oil pressure warning lights illuminated intermittently. The failure had become constant over time. The contact who is a certified mechanic, diagnosed the vehicle and determined that the camshaft had failed due to a camshaft position timing performance bank code. The contact replaced the spark plugs and, while doing so, noticed oil in the thread of cylinder #3 spark plug. The contact became aware of NHTSA Campaign Number: 17V209000 (engine and engine cooling). The dealer was contacted and confirmed that the VIN was not included in NHTSA Campaign Number: 17V209000 (Engine and Engine Cooling). The manufacturer was made aware of the failure and confirmed that the VIN was not included in the recall. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was 85,000.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Timing Belt Failure
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles).…
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Timing Belt Failure
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles).…
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Door Latch Failures
In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs…
In December 2019, the Office of Defects Investigation (ODI) opened this investigation based on 235 Vehicle Owner Questionnaires (VOQs) alleging doors failed to latch when closed, and/or inadvertently opened while driving, on model year (MY) 2012-2014 Ford Fiesta, and 2013-2014 Fusion and Lincoln MKZ. Some VOQs reported the failure occurred after the latch had been remedied under a prior recall which involved fracture of the latch pawl spring tab due to thermally induced cyclic fatigue. Other VOQs alleged a similar failure in vehicles not previously recalled. A latch with a fractured pawl spring tab typically results in a ?door will not close? condition, however in certain somewhat rare circumstances, may result in the door coming open while driving. In response to ODI?s investigation, Ford has announced three field actions, as discussed below.On March 23, 2020, Ford submitted Safety Recall 20V-177 (Ford 20S15), a regional recall campaign to address door latch failures in vehicles not previously recalled under Safety Recalls 15V-246, 16V-643 and 17V-210. The recall affects vehicles currently or ever registered in certain high ambient temperature states (see 20V-177 for affected states). As a remedy, Ford will replace all four door latches free of charge.On August 24, 2020, Ford issued a non-safety regional field action (Ford 20R01) to address door latch failures on the same model/MY vehicles not covered under 20V-177 (i.e., not currently/ever registered in affected states). According to Ford, spring tab failure rates for vehicles covered by this action are about half that of the 20V-177 vehicles. Under this action, dealers will replace all door latches, free of charge, if either; a) the vehicle exhibits a related latch concern, or b) if the vehicle owner expresses a concern about the latches in their vehicles. Details can be found under NHTSA TSB No. 10190990, a copy of which is available in this investigative file available at NHTSA.gov.On June 8, 2020, Ford submitted Safety Recall 20V-331 (Ford 20S30) addressing vehicles previously remedied under NHTSA Recalls 15V-246, 16V-643 and 17V-210, where the repair may not have been properly completed, specifically not all of the door latches were replaced, or replaced correctly. This recall involves an inspection of the latches, with the option for a consumer self-inspection; owners could view the date codes on their latches (and confirm child safety locks are present on the rear doors) and then submit the information to Ford?s mobile app or website. A dealership inspection option was also available. Any vehicle found to have unreplaced defective latches requires the replacement of all door latches as directed by Ford.Regarding the 4,494 reports cited above, 1,485 involve scope-related failures (with 13% alleging door opening), and the remaining 3,009 reports involving remedy concerns (with 18% alleging door opening - note ODI was unable to verify the allegations of door opening). The three ODI injuries were all relatively minor. Ford?s reported injury incidences include one (unconfirmed) report of an ejection, three minor injuries with the others involving undisclosed injuries. Ford?s crashes involved two (unconfirmed) crashes alleging the incident door contacted another vehicle and three involving doors striking other property.The recalled vehicles include MY 2011-2015 Ford Fiesta, 2013-2016 Ford Fusion and Lincoln MKZ, 2015 Ford Mustang and Lincoln MKC, 2013-2015 Ford Escape and Ford C-MAX, 2012-2015 Ford Focus and 2014-2016 Ford Transit Connect.Ford's actions address ODI's concerns at this time. ODI will take further action if warranted by new information. The reference (OD
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11006953Certain 2014-2015 Model Year Fiesta, 2014-2016 Model Year Fusion, MKZ and 2014-2016 Model Year Transit Connect Vehicles Not Covered in Safety Recall: 20S15 or 23S36 Door Latch Replacement and Inspection
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10251952For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
- 10237441Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT Due to ongoing limited part availability, program terms have been revised. Vehicle pickup & delivery has been added. Labor allowance table has been updated. Additional repairs updated. Added Attachment VI Mobile Repair/Vehicle Pickup and Delivery Record. Added Attachment VII Mobile Repair Assessment.
- 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
- 10226944Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission; Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT Non-Ford Part Usage: Vehicles that are still covered by the 8 years/80,000-mile Emissions warranty coverage MUST be serviced with a NEW Ford Motor Company TCM. Vehicles outside of or exceeding the 8 years/80,000-mile coverage are authorized to use a used Ford Motor Company TCM, a refurbished original Ford TCM, or an aftermarket TCM that will successfully complete the required Ford software updates.
- 10205009DPS6 - no satart and/or transmission engagement or loss of power with DTCS u0100, U00101, U1013, U3003 AND/OR P0606
- 10204994Online automotive service information system for March 2016
- 102049821.6L GTDI - Lack of power with MIL Illuminated - DTCS P0234, P0245, P0246 And/Or P0299. Some 2013-2016 Escape 2014-2016 Fiesta ST, and 2013-2014 Fusion vehicles equipped with a 1.6L Gasoline Turbocharged Direct Injection (GTDI) engine may exhibit a lack of power concern with malfunction indicator lamp (MIL) illuminated and diagnostic trouble codes (DTCs) P0234, P0245, P0246 and/or P0299 stored in powertrain control module (PCM) MEMORY.
- 10201050Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10199780Ford is extending the warranty coverage on the DPS6 automatic transmission TCM to 10 years of service or 150,000 miles from the warranty start date of the vehicle, whichever occurs first. This extended warranty coverage will address intermittent symptoms of loss of transmission engagement while driving, no-start, or a lack of power.
- 10194428Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10190990Under Safety Recall 20S15, in some of the affected vehicles, the door latches have a pawl spring tab that may break. This condition will typically prevent the door from latching. If the customer is able to latch the door, after repeated attempts to shut the door, these is a potential the door may unlatch while driving, increasing the risk of injury. Ford's analysis indicates that this condition is more likely to happen in states and territories with high ambient temperatures. For 20R01, owners will be notified that if their vehicle exhibits door latching concerns or if they are concerned about the latches in their vehicles, they may request repairs under this regional program.
- 10183749In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market
- 10180428Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
- 10180371This customer satisfaction program updates the TCM software in affected vehicles to provide improved detection and over warning of electrical circuit failures in the TCM. As communicated in a previous Customer Satisfaction Program (14M02), electrical circuit failures within the TCM may develop and result in intermittent symptoms of loss of transmission engagement while driving, no-start, or a lack of power. Updating the TCM software will help ensure the vehicle operator is alerted to potential issues with the TCM prior to failure.
- 10179185Some 2011-2019 Fiesta vehicles may exhibit various concerns following IPC replacement. Symptoms may include: no crank, 'Contact Hotline message', odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If programmable module installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new session using the appropriate Ford scan tool and perform a PMI on the IPC. Do not reconnect the IPC until after the scan tool states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.
- 10172972SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
- 10170917Some 2014-2018 Fiesta vehicles may exhibit a clicking noise from the driver side dash panel while operating the air distribution control. This may be due to a damaged door actuator and/or contact between the instrument panel (IP) ground and/or Sync 3 radio harnesses and the air distribution door actuating gear. To correct the condition, follow the Service Procedure steps to reroute the wiring harnesses and/or replace the door actuator.
- 10169986Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10164620Certain 2011 through 2015 Model Year Fiesta and 2012 through 2014 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission - Transmission Control Module Service Warranty Coverage
- 10164615Certain 2011 through 2015 Model Year Fiesta and 2012 through 2014 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission - Transmission Control Module Extended Warranty Coverage
- 10164612Certain 2011 through 2015 Model Year Fiesta and 2012 through 2014 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission - Transmission Control Module Reprogramming for Overt TCM Failure Warning
- 10164606Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission - Transmission Control Module Extended Warranty Coverage
- 10164603Certain 2014 through 2015 Model Year Fiesta and 2014 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission - Transmission Clutch Shudder / Transmission Clutch Warranty Extension
- 10164596Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10164508Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
- 10163594Short-Term DPS6 Dealer Customer Handling Direction
- 10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
- 10160880Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10159489Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
- 10156887Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
- 10155575Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
- 10153969Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
- 101487282014-2017 Fiesta, 2015-2018 Focus, 2018-2019 Ecosport vehicles equipped with a 1.0L EcoBoost engine may exhibit coolant consumption,white smoke and/or a runs rough condition. Refer to the extended coolant pressure test in Workshop Manual (WSM), Section 303-03. If no external coolant loss is confirmed, further investigation of the integrated exhaust manifold (IEM) interface is required. Carefully inspect the manifold port area for cracks. If a crack is found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01 for the repair procedures
- 10144207Some 2011-2018 Fiesta vehicles may exhibit various concerns following IPC replacement. Symptoms may include: no crank, Contact Hotline message, odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If programmable module installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new session using the appropriate Ford scan tool and perform a PMI on the IPC. Do not reconnect the IPC until after the scan tool states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.
- 10144182This article supersedes TSB 18-2024 to update the model years. Some 2011-2018 Fiesta vehicles may exhibit a lack of heat resulting from a frozen blower motor. This may be caused by snow entering through the cowl panel grille and screen assemblies. Snow may melt in the heating, ventilation and air conditioning (HVAC) case allowing water to enter the blower motor and freeze during a below freezing overnight soak. Blower motor fuse F4 in the battery junction box (BJB) may also be open and the cabin air filter may be saturated. Follow the Service Procedure steps to correct the condition.
- 10140323The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10140316Some 2011-2017 Fiesta vehicles may exhibit various concerns following IPC replacement including odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If Programmable Module Installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) session and perform a PMI on the IPC. Do not reconnect the IPC until after the IDS or FJDS states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.
- 10140309Some 2011-2017 Fiesta vehicles may exhibit a lack of heat resulting from a frozen blower motor. This may be caused by snow entering through the cowl panel grille and prior screen assemblies. Snow may melt in the heating, ventilation and air conditioning (HVAC) case allowing water to enter the blower motor and freeze during a below freezing overnight soak. The blower motor fuse at location F4 in the power distribution box may also be open and the cabin air filter may be water saturated. Follow the Service Procedure steps to correct the condition.
Every Ford Fiesta model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.