2006 Isuzu F-Series

Recalls

2 recalls name the 2006 Isuzu F-Series. Newest first.

• Parking brake

  Aug 28, 2007NHTSA 07V3850009,518 vehicles

  On certain straight towing or non-towing trucks equipped with bendix air brakes, the air brake park control valve may develop either an internal air leak or an air restriction. The park brake may not release or may release only partially.

  Risk and remedy

  Risk

  If the vehicle IS on an uneven surface, the park brake may not hold the vehicle and could result in unintended vehicle movement and a vehicle crash. this condition does not affect normal service braking.

  Remedy

  Dealers will inspect and replace the external check valve on the air brake park control valve if the inspection determines the external check valve IS damaged, the air brake park control valve will be replaced and may require the replacement of an internal check valve in the air brake park control valve. remedy will be free of charge. the recall began on october 22, 2007. owners may contact gm at 1-800-862-4389 or isuzu at 1-800-255-6727.

  Full recall details →

• Service brakes, air

  Aug 16, 2006NHTSA 06V3110001,369 vehicles

  Certain trucks fail to comply with the requirements of federal motor vehicle safety standard no. 121, "air brake systems." an internal control and check valve within the air brake application valve assembly was configured improperly, preventing air from flowing through the brake system as designed. in the event of an emergency stop, the vehicle's stopping…

  Risk and remedy

  Risk

  If stopping distance was limited, a vehicle crash could result.

  Remedy

  Dealers will replace the air brake application valve assembly on c-series or reroute the air brake lines on t-series free of charge. the recall began on september 20, 2006. owners may contact chevrolet at 1-800-630-2438, GMC at 1-866-996-9463 and isuzu at 1-800-255-6727.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11007177Information bulletin: this bulletin applies to all oem and remanufactured engine and transmission assemblies, for the affected vehicles listed above, to be replaced under the isuzu new vehicle warranty, goodwill, isuzu parts warranty, gold star used truck warranty and/or all extended powertrain warranties offered by isuzu, as well as all over-the-counter engine and transmission assembly replacements.
• 10244945The following information is provided to clearly explain Isuzus policy for control module (engine, transmission, antilock brake, instrument panel, body control, power interface, etc.) reprogramming. Control module calibrations are regularly updated for many reasons. These reasons may include, but are not limited to: model year change, software corrections, certification compliance, product improvement and specific application requirements. However, the mere existence of a newer control module calibration does not necessarily mean that warranty coverage exists or that the calibration must be installed. It is not our policy to update control modules, under warranty or after warranty, based solely on the availability of a newer calibration file. Below are our guidelines for reprogramming control modules.
• 10237146This bulletin outlines the procedures for using the Alpine Exchange Program (the "Exchange Program"). The Exchange Program must be used when any Alpine radio or other component covered by this bulletin is repaired under warranty and may also be used for radio and component repairs not covered under warranty. Contact Alpine directly for pricing and payment methods applicable to radio and component repairs not covered under warranty.
• 10218932Isuzu Commercial Truck of America, Inc. (ICTA) is providing the following procedural recommendations to improve dealer efficiency when submitting Parts Warranty claims. We strongly recommend dealers follow these procedures in order to avoid delays in Parts Warranty claim payments and/or claim chargeback. This bulletin was revised to add a Parts Warranty Form
• 10218927Isuzu Commercial Truck of America, Inc. (ICTA) is providing the following procedural recommendations to improve dealer efficiency when submitting Parts Warranty claims. We strongly recommend dealers follow these procedures in order to avoid delays in Parts Warranty claim payments and/or claim chargeback.
• 10217004The Isuzu Commercial Truck of America (ICTA) Service Technical Assistance Center (TAC) provides diagnostic support to Isuzu dealer technicians repairing Isuzu vehicles in and out of vehicle warranty. A TAC case number will be issued solely for information tracking purposes and future contact reference.
• 10217001The following is a list of the Isuzu-recommended Threebond product part numbers identified in the various Isuzu Workshop Manuals and bulletins. If a Threebond product is unavailable, we recommend that you utilize the chart below to find equivalent of similar products (when available) from Loctite and Permatex.
• 10176607This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 10175863Proper installation of the fuel injector pipes into a long block assembly the fuel injection pipes should be installed onto the new long block assembly after first installing the common rail. When installing the fuel injection pipes, follow the procedure below to ensure proper mating of the fuel injector high-pressure inlet, and the fuel injection pipes. Refer to the appropriate year and model service manual for further information regarding the replacement procedure.
• 10154566This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
• 10154552This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
• 10154306This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
• 10154299This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
• 10139437This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
• 10130290This bulletin IS being issued to inform dealers of diesel particulate filter (dpf) cleaning recommendations, inspection practices, and recommended r&r procedures for service and cleaning system availability.
• 10126972This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
• 10125956This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Technician will need to use a scan tool and verify current Digital Radio Receiver Status under Data Display. Technician will need to look at the second line labeled Digital Radio Receiver Status will display a number of 00 - 04. Technician will repair per the status code.
• 10125106This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
• 10118233This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
• 10114598This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
• 10114474This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
• 10114408This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
• 10114352This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
• 10114343This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
• 10114342This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
• 10112664This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
• 10112641This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
• 10112607This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
• 10112331This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
• 10112329This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
• 10112160This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
• 10112116This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
• 10112013This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
• 10055254Isuzu: information concerning the installation of the fuel injector pipes into a long block assembly. 1999 - 2002 isuzu fsr/ftr/fvr, 1999 - 2009 chevrolet or GMC t6500/t7500/t8500, 2000 - 2004 chevrolet or GMC wt5500, 2000 - 2004 isuzu frr, 2003 - 2009 chevrolet or GMC c6500/c7500/c8500, 2004 - 2009 isuzu ftr/fvr/fxr, 2005 - 2007 isuzu htr/hvr/hxr, 2005 - 2010 chevrolet or GMC w3500/w4500/w5500, 2005 - 2015 isuzu npr/nprhd/nqr/nrr, and 2013 - 2014 isuzu npr.
• 10046799Isuzu (chevrolet/gmc): trucks with diesel engine would have idle vibration, trouble starting, engine not revving up, and a lack of power due to possible operation condition of suction control valve (scv)/fuel rail pressure (frp) regulator being intermittent. Models 2004-2010 chevrolet/gmc c, t, w series and isuzu f, h, n series.
• 10037184Gm: service bulletin explaining when the safety belts are supposed to lock. Updated 12/6/11.
• 10033725Isuzu truck: instrument panel cluster exchange procedure when replacement IS necessary. Follow diagnostic and repair information found in the intstrument panel gauges and console sub section of service information. If diagnosis points to concern with ip cluster and cluster needs to be replaced, follow exchange procedure.

Every Isuzu F-Series model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.