2012 Mercedes-Benz E350
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › E350 › 2012
These records cover every 2012 Mercedes-Benz E350. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2012 Mercedes-Benz E350. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 E400 Coupe, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2011-2014 E350 Coupe, and 2012-2014 E350 Cabrio vehicles. An incorrect front passenger air bag may have been installed during a prior repair.
Risk and remedy
Risk
An incorrect air bag may not function properly in a crash, increasing the risk of injury.
Remedy
Dealers will replace the front passenger air bag on the affected vehicles, free of charge. Owner notification letters were mailed on September 10, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…
Risk and remedy
Risk
If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691
Mercedes-Benz is recalling certain model year 2011-2012 S400, S550, S550 4Matic, S63 AMG, C300, C300 4Matic, E350, GLK350, GLK350 4Matic, CL550 4Matic, and CL63 AMG vehicles manufactured from April 18, 2011, through July 12, 2011. Due to an irregularity stemming from the molding process of the fuel filter flange, the fuel filter flange may crack when…
Risk and remedy
Risk
If the fuel filter flange cracks, it will leak fuel which may lead to a fire if an external ignition source is present.
Remedy
Mercedes-Benz will notify owners, and dealers will replace the fuel filter, free of charge. The recall campaign is expected to begin in February 2013. Owners may contact Mercedes-Benz at 1-800-367-6372.
Mercedes-Benz is recalling certain model year 2012 E350 and E550 Coupe vehicles, manufactured April 2, 2012, through June 29, 2012. Improper stitching of the right side window curtain air bag may cause it to not deploy as intended in the affected vehicles.
Risk and remedy
Risk
In the event of an accident necessitating the deployment of the right window curtain air bag, the improper stitching may cause it to deflate more quickly than intended, reducing the protection it may provide, resulting in an increased risk of injury to vehicle occupants.
Remedy
Mercedes-Benz will notify owners, and dealers will replace the right side window curtain air bag. The recall began on December 21, 2012. Owners may contact Mercedes-Benz at 1-800-367-6372.
Owner complaints
217 complaints6 involved a crash1 involved a fire5 injuries
What owners report most
Latest complaints
- Electrical system · Seats · Steering
The vehicle was parked when the steering wheel locked , and the headrest. The electrical for my headlight driver side low beam gave me a warning lamp message.
- Engine and engine cooling › Engine › Crank/camshaft position sensor
The contact owns a 2012 Mercedes-Benz E-350. The contact stated that while attempting to start the vehicle, the check engine warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with a failed crankshaft sensor. The contact stated that the crankshaft…
The contact owns a 2012 Mercedes-Benz E-350. The contact stated that while attempting to start the vehicle, the check engine warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with a failed crankshaft sensor. The contact stated that the crankshaft sensor was replaced; however, the failure reoccurred. The vehicle was taken to another independent mechanic where the contact was informed that the crank shaft sensor needed to be replaced. The vehicle was repaired; however, the failure reoccurred. The vehicle was taken to another independent mechanic, and the crankshaft sensor was replaced. The vehicle was repaired, but the failure reoccurred. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 152,000.
- Fuel system, gasoline
The contact owns a 2012 Mercedes-Benz E350. The contact stated that while driving at an undisclosed speed, there was an abnormal odor coming from the inside of the vehicle. No warning lights were illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed with a fuel leak.…
The contact owns a 2012 Mercedes-Benz E350. The contact stated that while driving at an undisclosed speed, there was an abnormal odor coming from the inside of the vehicle. No warning lights were illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed with a fuel leak. The vehicle was not repaired. The contact researched and was made aware of NHTSA Campaign Number: 12V557000 (Fuel System, Gasoline); however, the VIN was not included in the recall. A dealer was contacted; however, the vehicle was not yet diagnosed by the dealer. The manufacturer was notified of the failure. The failure mileage was approximately 70,000.
- Service brakes
Brake failure due to leaking brake fluid after dealership conducted rear sub frame extended warranty coverage replacement and recent brake fluid services and after two (2) multi point inspections including video and reported “no items failed” and “no items cautioned.” Vehicle was released to me…
Brake failure due to leaking brake fluid after dealership conducted rear sub frame extended warranty coverage replacement and recent brake fluid services and after two (2) multi point inspections including video and reported “no items failed” and “no items cautioned.” Vehicle was released to me both times Vehicle was inspected and is available for further inspections. My safety was jeopardized due to brake system failure while traveling at high speed on public highway. The problem was confirmed by two (2) dealerships. “ Please see below for recommended repairs on your 2012 E350, VIN - [XXX] Inspection by a different Mercedes Benz dealership reported the following: [XXX] Concern – vehicle is leaking brake fluid from behind the drivers front wheel / tire Cause – Confirmed concern, installed vehicle on lift and found brake fluid dripping from plastic side panel under the drivers door. Brake fluid flush recently completed on vehicle by Portsmouth MB, verified bleeding valves on calipers are tight and not leakingRemoved paneling and found fluid is dripping from wheel well area. Removed left front wheel well cover, and found rear brake lines are leaking due to heavy corrosion and bubbling (see attached photo). Correction – Rear brake lines need to be replaced to repair. Due to corrosion, will require brake hoses due to rotted connections. Lines are formed, fitted and secured by technician during repair (they do not come pre-formed to vehicle). Repair Estimate – Labor ($199.88 / hr) 9 hours (includes diagnostic time), $1798.92 Parts, estimate $690 if no further connections are needed (tax included) Shop supplies, $26.95 Estimate $2520 total repair **Tech notes there is a fuel line running in an area of the brake lines that is showing bubbling in the metal, not yet leaking. Additional $375 parts and labor to replace if we replace with the brake lines. MB parts states there are only 2 of these lines remaining globally.” INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)
- Electrical system › Seat heater › Wiring harness · Fuel system, gasoline › Delivery › Fuel pump
The contact owns a 2012 Mercedes- Benz E350. The contact stated while operating the vehicle the odor of fuel was present coming from the vehicle. Upon inspection it was discovered that the fuel had leaked from the vehicle. The vehicle was taken to the local dealer who diagnosed that the fuel pump…
The contact owns a 2012 Mercedes- Benz E350. The contact stated while operating the vehicle the odor of fuel was present coming from the vehicle. Upon inspection it was discovered that the fuel had leaked from the vehicle. The vehicle was taken to the local dealer who diagnosed that the fuel pump had failed and needed to be replaced. The vehicle was not yet repaired. Also, the contact indicated that the front driver seat heat element had overheated and cause melting to the seat cushion. The vehicle was taken to the local dealer who diagnosed that the front driver seat needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failures but no assistance was offered. The failure mileage was 35,000.
- Fuel/propulsion system · Suspension
The failed component is a fuel pump, and it is available for inspection upon request. My safety and the safety of others was put at risk due to the following: 1) Sudden engine stalling 2) Dangerous power loss while accelerating 3) Potential fire risks; a damaged fuel pump assembley can cause fuel…
The failed component is a fuel pump, and it is available for inspection upon request. My safety and the safety of others was put at risk due to the following: 1) Sudden engine stalling 2) Dangerous power loss while accelerating 3) Potential fire risks; a damaged fuel pump assembley can cause fuel leaks and overheating due to insufficient fuel supply can increase the risk of explosion or fire. 4) Gas fumes from a fuel leak are highly harmful and dangerous. They are toxic to inhale causing dizziness, headaches, nausea or respitory issues.
- Back over prevention › Sensing system › Camera
Rear camera fails unexpectedly when placing car in reverse
- Service brakes
The brake lines on my car rusted out from the brake booster all of way to the rear calipers. This is the third time it’s happened to me as I’ve owned multiple E classes. If Mercedes-Benz covers the subframe, why is the brake lines which are located right above said subframe not covered?
- Service brakes · Unknown or other
The rear subframe got separated from chassis. I was driving to work and had to hard brake to void a collision with another vehicle all of a sudden vehicle shifted to the left and I ended up on a curb. Further inspection vehicle`s rear subframe rotted out due to rust. Also, both rear brake lines…
The rear subframe got separated from chassis. I was driving to work and had to hard brake to void a collision with another vehicle all of a sudden vehicle shifted to the left and I ended up on a curb. Further inspection vehicle`s rear subframe rotted out due to rust. Also, both rear brake lines from abs module to calipers are damaged due to corrosion. I ended up replacing both brake lines and did not think too much of it and now I see a lot of people complaining about both brake line corrosion and subframe separation or excessive rust, casing rear subframe to fail. It is a very serios safety issue and Mercedes should hold accountable for these failures. My vehicle is 2012 Mercedes E350 and only has 118k miles on odometer. I have attached pictures for the rear subframe for your review, but I did not take any pictures of the brake lines due to limited space to get my camera between the body and the rear subframe.
- Service brakes · Suspension
Brake line is thoroughly corroded, went to a repair shop, when they brought it back down, the Subframe collapsed. Mercedes has a 20 yr warranty on the subframe so they will cover that but want another $3K to fix the brake line that was obviously tied to the same mfr issue that the sub frame was in regards to rusting. Dealer won't take any responsibility for anything but the subframe.
- Power train › Automatic transmission › Lever and linkage › Column shift · Steering › Column
The contact owned a 2012 Mercedes-Benz E350. The contact stated that while attempting to shift to drive(D), the gear shifter detached from the steering column. No warning light was illuminated. Neither a dealer nor an independent mechanic was contacted. The vehicle was not taken to a dealer or…
The contact owned a 2012 Mercedes-Benz E350. The contact stated that while attempting to shift to drive(D), the gear shifter detached from the steering column. No warning light was illuminated. Neither a dealer nor an independent mechanic was contacted. The vehicle was not taken to a dealer or independent mechanic to be diagnosed. The vehicle was not repaired. The vehicle was towed to the residence by AAA. The manufacturer was not notified of the failure. The failure mileage was 420,000.
- Service brakes
I recently took my 2012 Mercedes-Benz E350 to an authorized Mercedes-Benz dealership after experiencing corrosion of the rear subframe. The dealership confirmed and is servicing the vehicle under an active recall notice that extended the original New Vehicle Limited Warranty from 4 years/50,000…
I recently took my 2012 Mercedes-Benz E350 to an authorized Mercedes-Benz dealership after experiencing corrosion of the rear subframe. The dealership confirmed and is servicing the vehicle under an active recall notice that extended the original New Vehicle Limited Warranty from 4 years/50,000 miles to 20 years /unlimited miles. After removing the subframe for repair, they observed serious corrosion of the brake lines. There had been no warnings or symptoms to alert me to any corrosion problems with the brake line prior to this. Most likely, the issue would not have been discovered if the dealership had not removed the subframe. The dealership advised me that this issue requires immediate service due to safety concerns (potential failure) as the braking system could fail while driving the vehicle. The cost to have the work done is $5800. Beyond the dealership service center, I'm not aware if brake line has been inspected by others (engineers) in Mercedes-Benz. However, this issue appears to be frequently observed in vehicles experiencing the rear subframe corrosion issue.
- Unknown or other
Gasoline Fuel System problem of the 2012 Mercedes Benz E350. Driver side fuel leak was excessive. Leak caused an excessive amount of gas to spill while driving on a 600 mile long round trip to St. Louis. The fuel filter sending unit had numerous stress cracks in the plastic. A massive failure…
Gasoline Fuel System problem of the 2012 Mercedes Benz E350. Driver side fuel leak was excessive. Leak caused an excessive amount of gas to spill while driving on a 600 mile long round trip to St. Louis. The fuel filter sending unit had numerous stress cracks in the plastic. A massive failure was looming. I have pictures and have documented the failure. 2184700194 was the original part and now has changed too 2184700994. A component should be easily inspected to prevent such a dangerous situation. For the past 13 all services work was preformed by Mercedes.
- Air bags · Seats
Air bag notice on monitor, Passenger front seat locked in forward position up to the dashboard..
- Electrical system · Steering
Steering wheel lock module steering wheel was locked in place and vehicle wouldn’t do anything.
- Fuel system, gasoline
The contact owns a 2012 Mercedes-Benz E350. The contact stated while driving 5 MPH, the contact smelled fuel on the interior of the vehicle. No warning lights were illuminated. The contact stated that the dealer was contacted. The vehicle was taken to an independent mechanic where it was diagnosed…
The contact owns a 2012 Mercedes-Benz E350. The contact stated while driving 5 MPH, the contact smelled fuel on the interior of the vehicle. No warning lights were illuminated. The contact stated that the dealer was contacted. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the fuel filter sending unit needed to be replaced. The vehicle was being repaired. The contact related the failure to NHTSA Campaign Number: 12V557000 (FUEL SYSTEM, GASOLINE). The manufacturer was notified of the failure and informed the contact that the VIN was not included in the recall. The failure mileage was 124,900.
- Fuel/propulsion system
I have a 2012 E350 with less than 95000 miles and I see these vehicles were recalled in the past for their fuel tank manufacturer malfunction but my VIN number was not included. This car went numerous times to the mechanics and the fuel components fixed but it still leak gas and smells even when I…
I have a 2012 E350 with less than 95000 miles and I see these vehicles were recalled in the past for their fuel tank manufacturer malfunction but my VIN number was not included. This car went numerous times to the mechanics and the fuel components fixed but it still leak gas and smells even when I do not drive the car. I spent over $15000 on this matter. This is now becoming a safety issue for me and my neighbors. I don't know what to do. Here is what happened. All began February 2023, I towed the car to an approved MB mechanics who said fixed the car. 9 month later, I brought the car back for the same issue. Strong fuel smell. The attachments for repairs will show the work done. Some repeated and recharged to me. The following year April 2024, I woke up one day with a fas leak all over my drive way and a strong smell of gas. I had the car towed for a repair cost of $7754 total. I am constantly having the same problem with the car and wanted to alert here to bring Mercedes Benz awareness to their faulty parts putting consumer lives at risk.
- Engine · Fuel/propulsion system · Unknown or other
Recall exists related to a potential issue with the high-pressure fuel pump, which could lead to engine stalling and increase crash risk. My 2012 Mercedes E350 stops the engine in the middle of the road couple of times and for some reason, its stops or shut off the engine completely. The last time…
Recall exists related to a potential issue with the high-pressure fuel pump, which could lead to engine stalling and increase crash risk. My 2012 Mercedes E350 stops the engine in the middle of the road couple of times and for some reason, its stops or shut off the engine completely. The last time I was pulling out on the main road and stop right there. I made a big traffic, and I was scared because I cannot start the car. The guy stops and help me to push out of the road, but we cannot push the vehicle unless someone is inside the car. If I go out, it will automatically go on "park" and cannot push the car. When you check the dashboard the check engine light is not on. 2nd incident I bring this car to Mercedes Benz Dealership, and I told them that there is something wrong in my car, I explain what was wrong but, the guy I talk to, told me that if the check engine light is not coming on, my car is fine. I repeated that the car stops ones in a while when the temperature light is on inside the dashboard and the engine shuts off. He told me if the check engine light turns on then I bring it back. I show the code reading but the same thing he said. I left and went back home and suddenly I get stranded again; I got stock in the middle of the road for 3 to 4 minutes. I start the car and suddenly the car starts and find the nearest place to pull over. I let it call down for couple of hours and start again, the car starts and try to go back home. When I was in the interstate hwy. My car engine shut off, so I quickly pull over, but I was having a hard time to turn the wheel. I believe that this is very unsafe and should have Mercedes Dealer has to repair this issue. I research on the website that 2012 Mercedes Benz E350 have recall to a potential issue with the high- pressure pump and other things like Battery fuse relay box positive terminal and low fuel circuit.
- Suspension › Subframe/mounting bracket
The contact owns a 2012 Mercedes-Benz E350. The contact stated his wife had noticed that the steering wheel was off-center and turned to the left independently. Additionally, the contact stated while his wife was driving at an undisclosed speed and depressing the brake pedal, the vehicle flipped…
The contact owns a 2012 Mercedes-Benz E350. The contact stated his wife had noticed that the steering wheel was off-center and turned to the left independently. Additionally, the contact stated while his wife was driving at an undisclosed speed and depressing the brake pedal, the vehicle flipped sideways. The contact's wife was able to exit the highway and pull into a gas station. The contact met his wife at the gas station. The contact stated that while driving approximately 20 MPH, the failure recurred, with the front end shifted to the left and the rear end shifting to the right. The contact returned to the parking lot. The vehicle was towed to the residence. The contact stated that as an independent mechanic, he inspected the vehicle and noticed that the rear subframe was corroded severely inside out and a wheel had detached. The dealer and the manufacturer were not notified of the failure. The vehicle was not diagnosed or repaired. The failure mileage was approximately 170,000. The VIN was not available.
- Structure › Body
Rear Subframe is rusted through. My mechanic just pointed this out today, during regular maintenance, and provided photographs.
- Engine · Fuel/propulsion system
[XXX].The engine intake manifold on our 2012 Mercedes E350 (64,000 miles) EXPLODED with enough force to bend the hood up 2 inches. It was a damp cold morning & the engine had not been started in 12 hours. The car was not locked & the key fob was nowhere close. The fuel level was under 3/4 full.…
[XXX].The engine intake manifold on our 2012 Mercedes E350 (64,000 miles) EXPLODED with enough force to bend the hood up 2 inches. It was a damp cold morning & the engine had not been started in 12 hours. The car was not locked & the key fob was nowhere close. The fuel level was under 3/4 full. This happened when wife went to get something out of the car and when she pulled the passenger door handle to open - B O O M !!!! If this happened 30 minutes later, I would have been under that hood checking the fluid levels for a trip to San Francisco. I WOULD HAVE BEEN SERIOUSLY HURT OR KILLED!. It was towed to Mercedes-Benz of Carlsbad, Carlsbad California on [XXX] & they have not been able to identify the cause. They could replace the broken parts at the cost of $8,000 but that doesn’t fix the problem. And if it happens again & hurts or kills someone, they could be held liable. Similar intake explosions have occurred on these Mercedes engines but Mercedes is denying any knowledge even though it’s clearly a dangerous design flaw in this intake system. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Forward collision avoidance › Automatic emergency braking · Fuel/propulsion system · Seats
I am writing in regards to the 5 vehicle recalls that were for the make, and model of my car that is showing as having no recalls for. The recalls involved air bags, air bag software, fuel filter flange, and I am also wondering with the driver headrest deployment module if that is associated with…
I am writing in regards to the 5 vehicle recalls that were for the make, and model of my car that is showing as having no recalls for. The recalls involved air bags, air bag software, fuel filter flange, and I am also wondering with the driver headrest deployment module if that is associated with an airbag module; as when I had purchased the vehicle I had found out that both my airbag modules had malfunctioned with showing the srs lights on the dash. I was told that Mercedes of Sarasota, FL had replaced the passenger airbag module by Mercedes of South Orlando. When asked for a printout verification of this repair showing to be completed; they said they couldn’t provide me with this information. As proof of the service to being completed could not be provided. I had tken my car to their to have them look into this, and the tpms sensors showing malfunctioned; communication error message, and they couldn’t figure out what the problem was causing this. I had to take my car to an auto electrician to find out the problem; that I had found out that a 100 amp fusible link had blown, causing all those problems with also the roof wasn’t working. Along with I was smelling fuel. I found out about the recall for these items after getting them repaired out of pocket by the auto electrician Mike from Peak Audio, and Electric, and as to the fuel filter flange I had to pay like $1,200 to replace as they had replaced the fuel level sending unit that include the fuel filter flange. I would like refun; still have the headrest driver side that needs to be replaced. I found out that their is an recall for this make, and model of car that had said the air bag deployment software was under recall for those vehicles; which I believe could have triggered the deployment of the head rest while I was driving; as if I had been near a car; I could have been involved in an accident. I think that this should have an open ticket for repair placed on all 2012 Mercedes E350 Cabriolet Blue Efficiency.
- Service brakes
2012 e350 both rear brake metal lines rusted out January 2025 brakes gave out. This is definitely connected to the rear subframe rusting too.
- Service brakes · Suspension
Rear subframe corrosion and in addition, rear break line corrosion.
- Fuel/propulsion system
Recently, I have noticed a strong gas smell emanating from the rear driver’s side of the vehicle. Upon further research, I discovered that there was an open recall affecting Mercedes E-Class vehicles of the same year for a similar issue. However,my vehicle’s VIN is not included in this recall.…
Recently, I have noticed a strong gas smell emanating from the rear driver’s side of the vehicle. Upon further research, I discovered that there was an open recall affecting Mercedes E-Class vehicles of the same year for a similar issue. However,my vehicle’s VIN is not included in this recall. Given that my vehicle is experiencing the same problem described in the recall, I am concerned about the safety implications and believe this matter warrants immediate attention. I would like clarification on why my vehicle is excluded from the recall despite exhibiting the same issue. Additionally, I would like to know if I am expected to pay out of pocket for repairs related to what appears to be a manufacturing defect acknowledged by Mercedes-Benz for other vehicles of the same year and model. I kindly request that this matter be escalated for review, and I look forward to your prompt response. My goal is to ensure the safety of my vehicle without incurring unfair expenses for a known issue.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Rear brake line failure
On April 10, 2020, NHTSA's Office of Defects Investigation (ODI) received a defect petition from Mr. Surjit Singh alleging premature corrosion of the rear brake lines in his 2013 Mercedes-Benz E350 sedan. The petitioner states that he was recently informed by a Mercedes dealer service department that his car had…
On April 10, 2020, NHTSA's Office of Defects Investigation (ODI) received a defect petition from Mr. Surjit Singh alleging premature corrosion of the rear brake lines in his 2013 Mercedes-Benz E350 sedan. The petitioner states that he was recently informed by a Mercedes dealer service department that his car had severely rusted brake lines that need[ed] to be replaced immediately at a cost of about $3300. He further stated that the dealer service advisor informed him that he had seen the issue on many cars like his. The petitioner requested ?that NHTSA launch an investigation into this serious issue of rusting brake lines on [his] 2013 Mercedes E350.? The brake line corrosion reported by the petitioner did not result in brake line leakage or any compromise in brake system performance before it was detected in a dealer vehicle inspection. The petitioner submitted a complaint to NHTSA documenting his experience (NHTSA ID 11319024).On April 24, 2020, ODI opened Defect Petition DP20-004 to evaluate the petitioner?s request. ODI conducted a search for all consumer complaints and Early Warning Reporting (EWR) data related to allegations of brake line corrosion or leakage in 2013 Mercedes-Benz E350 sedans and similarly equipped vehicles. The 2013 E350 is a fourth-generation Mercedes-Benz E-Class vehicle (W212 platform), which was first sold in the United States in 2009 as a 2010 model. Mercedes-Benz sold approximately 245 thousand model year 2010 through 2015 E-Class sedan and wagon vehicles in the United States with the same brake line design as the petitioner?s vehicle.ODI?s search for complaints and EWR data in 2013 Mercedes E350 vehicles found no additional records related to the alleged defect. Expanding the search to all W212 platform vehicles identified just one incident, a complaint alleging unspecified brake line corrosion and leakage in a 2011 Mercedes-Benz E550 (NHTSA ID 10902081). The complaint did not allege that the brake line leakage resulted in reduced brake performance, crash, or injury. The resulting failure rate of 0.4 failures per hundred thousand vehicles is extremely low for a population that includes vehicles that have been in service for over ten years. After reviewing the available data, ODI has not identified evidence of a defect trend in the subject E-Class vehicles that would support opening a defect investigation into premature brake line corrosion failure. NHTSA is authorized to issue an order requiring notification and remedy of a defect if the Agency?s investigation shows a defect in design, construction, or performance of a motor vehicle that presents an unreasonable risk to safety. 49 U.S.C. ?? 30102(a)(9), 30118. Since the information before the Agency is not indicative of a vehicle-based defect, it is unlikely that any investigation opened because of granting this petition would result in an order concerning the notification and remedy of a safety-related defect. Therefore, upon full consideration of the information presented in the petition and the potential risks to safety, the petition is denied. The denial of this petition does not foreclose the Agency from taking further action if warranted or the potential for a future finding that a safety-related defect exists based upon additional information the agency may receive.A Federal Register notice further detailing NHTSA?s reasons for denial of the petition will be forthcoming.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007750Complaint Dynamic seat function or multicontour system inoperative Noises from area of lateral support bladder Cause Lateral support bladder leaking Remedy Replacement of complete air cushion insert.
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10235978Recall Campaign announcement for Takata driver airbags.
- 10235673To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut.
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232334To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut. The purpose of this NCU update is to alert you that: 1. The settlement went into effect on January 23, 2023. Customers are now eligible to receive extended warranty coverage and may start contacting authorized Mercedes-Benz dealerships to schedule an appointment for the repairs. 2. Before scheduling a repair appointment and ordering replacement parts kits: The customer should be given a repair order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the repair order before the parts kit can be ordered.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10231042To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut. The purpose of this NCU update is to alert you that: 1. The settlement went into effect on January 23, 2023. Customers are now eligible to receive extended warranty coverage and may start contacting authorized Mercedes-Benz dealerships to schedule an appointment for the repairs. 2. Before scheduling a repair appointment and ordering replacement parts kits: The customer should be given a repair order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the repair order before the parts kit can be ordered.
- 10210920Mercedes-Benz USA, LLC (MBUSA) is modifying the emission control system on certain diesel vehicles. The Emission Modification for MY11-12 E350 BlueTEC (W212) vehicles has been approved by EPA and CARB, and is now ready for installation. An authorized Mercedes-Benz Dealer will install the Emission Modification at no cost to the Owner/Lessee. What Were Doing An authorized Mercedes-Benz Dealer will replace certain emission control system components and update certain software in eligible vehicles.
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10205265Outside mirror fogged.
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205239"Anti-theft protection activated".
- 10205237The COMAND unit does not start or the display remains dark.
- 10205236"Metadata loss- Please reimport all media data".
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205229No/poor radio reception in AM frequency range.
- 10205228No/poor radio reception in AM frequency range.
- 10205154Gasket may settle causing a slight oil leak.
- 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
- 10186142Unmotivated Reaction from Park Assist - model series 213 facelift / 238 facelift with option code 235 (active par- king assist) and option code 501 (surround view system)
- 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
- 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
Every Mercedes-Benz E350 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.