2016 Mercedes-Benz E350

Recalls

5 recalls name the 2016 Mercedes-Benz E350. Newest first.

• Communication

  Nov 1, 2019NHTSA 19V78700024,226 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…

  Risk and remedy

  Risk

  An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

  Remedy

  MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

  Full recall details →

• Air bags › Frontal

  Oct 6, 2017NHTSA 17V627000495,290 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…

  Risk and remedy

  Risk

  If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.

  Remedy

  MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.

  Full recall details →

• Air bags › Frontal › Sensor/control module-inactive

  Mar 14, 2017NHTSA 17V17700051 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550…

  Risk and remedy

  Risk

  If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

  Remedy

  MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

  Full recall details →

• Steering › Electric power assist system

  Dec 14, 2016NHTSA 16V89900070 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2013-2015 SL550, 2013-2014 SL63 AMG, 2014-2016 E350, 2014 E350 Cabriolet, E350 Coupe, 2014-2015 S550, 2015 E350 Bluetec, 2015-2016 E400, 2016 E550 Coupe, and Maybach S600 vehicles manufactured August 23, 2012, to August 14, 2015. The affected vehicles use an electric power steering system that…

  Risk and remedy

  Risk

  If the control unit pins lose connection, there would be a loss of electric power steering assist, increasing the risk of a crash. The increase in pin contact resistance can also increase the risk of a fire, even while the vehicle is parked and ignition is off.

  Remedy

  MBUSA will notify owners, and dealers will replace the electric power steering control unit, free of charge. The recall began October 13, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

  Full recall details →

• Engine and engine cooling › Engine

  Aug 11, 2015NHTSA 15V505000209 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 Mercedes Benz E350, E400, E400 4Matic, E63 4M S AMG, E350 4Matic, E63-4M S AMG, 2015 CLS400, CLS400 4Matic, CLS550, CLS63-4M "P" AMG, and CLS550 4Matic vehicles manufactured April 16, 2015, to April 22, 2015. The integral steel cable that secures the rubber seal to the bulkhead might have…

  Risk and remedy

  Risk

  If the rubber seal falls into the engine compartment, it may contact parts of the engine or exhaust system, increasing the risk of a fire.

  Remedy

  MBUSA will notify owners, and dealers will replace the rubber seal, in the engine compartment, free of charge. The recall began on September 2, 2015. MBUSA's number is 2015080001. Owners may contact MBUSA customer service at 1-201-573-5339.

  Full recall details →

Owner complaints

What owners report most

1. Electrical system9
2. Structure7
3. Unknown or other7
4. Air bags6
5. Vehicle speed control5
6. Steering5
7. Power train5
8. Engine5
9. Visibility/wiper4
10. Service brakes3

Latest complaints

• Jul 16, 2026VA
  Structure › Body · Suspension
  The rear subframe is defective and subject to premature corrosion and failure of parts that connect to the rear suspension. Due to the fracturing of the joints connecting to the suspension, my car was at risk of going out of control when needing to brake at higher speeds. The way the suspension…

  The rear subframe is defective and subject to premature corrosion and failure of parts that connect to the rear suspension. Due to the fracturing of the joints connecting to the suspension, my car was at risk of going out of control when needing to brake at higher speeds. The way the suspension component broke also risked damage to the gas tank if the car was driven over a large bump or pot hole. The problem was diagnosed by an independent repair service. The corrosion is not visible to an owner. It does not impact any body panels - only structural parts visible when the vehicle is on a lift. Mercedes Benz has provided an extended warranty for unlimited miles and 20 years to any owner of this model for a range of years and models. This was communicated to Mercedes Benz dealerships on March 10, 2023. However, since the vehicle is not subject to recall, I do not know how this was communicated to an owner. I did not receive anything alerting me to the problem. Mercedes Benz has my phone number on file.

• Mar 16, 2026LA
  Air bags · Seats

  Passenger seat capacity sensor fault. Will not activate passenger side air bag. Checked with obd scanner

• Jan 27, 2026NY
  Fuel/propulsion system

  Fuel odor is very apparent (while idle) but difficult to identify location. Same models seem to have recalls for fuel injectors/rails but not this specific VIN. I believe the issue might be of similar recall. I will have the car diagnosed soon.

• Dec 5, 2025MS140,000 mi
  Structure · Visibility › Windshield
  The contact owns a 2016 Mercedes-Benz E350. The contact stated that water was leaking inside the vehicle through the seal around the windshield. The contact stated that upon manually pushing the windshield, the windshield was movable. Additionally, the contact stated that there was a windy sound…

  The contact owns a 2016 Mercedes-Benz E350. The contact stated that water was leaking inside the vehicle through the seal around the windshield. The contact stated that upon manually pushing the windshield, the windshield was movable. Additionally, the contact stated that there was a windy sound coming through the windshield while driving. The vehicle was taken to Dunaway Glass Repair Company, where the windshield was being replaced. The vehicle was being repaired. The manufacturer was notified of the failure and informed the contact that the VIN was not under recall. The manufacturer referred the contact to the NHTSA Hotline for the VIN to be added to a recall for potential reimbursement. The failure mileage was approximately 140,000.

• Oct 16, 2024CA
  Engine
  Since May 2024, I had taken my car in for repairs at 3 different shops for same exact issue diagnosed as leak from air intake system. It has been repaired 7 times since it first occurred in May 2024, and unfortunately it is still not resolved. This is a potential danger to the driver because all of…

  Since May 2024, I had taken my car in for repairs at 3 different shops for same exact issue diagnosed as leak from air intake system. It has been repaired 7 times since it first occurred in May 2024, and unfortunately it is still not resolved. This is a potential danger to the driver because all of a sudden there will be loud noise from the engine, car will start misfiring and slow down the speed. The previous 3 attempts of repair were made at Mercedes Benz of West Covina. The car is non drivable at the moment.

• Oct 11, 2024PR
  Electrical system · Forward collision avoidance › Automatic emergency braking · Unknown or other
  Q1: Yes, it is available for inspection upon request. The instrument cluster showed some messages* randomly appearing/beeping on and off but there were other issues present: • Acceleration not possible in drive • At one point transmission would not shift from gear 3 • *Speedometer would go up and…

  Q1: Yes, it is available for inspection upon request. The instrument cluster showed some messages* randomly appearing/beeping on and off but there were other issues present: • Acceleration not possible in drive • At one point transmission would not shift from gear 3 • *Speedometer would go up and down randomly until it eventually stayed at 0 physically and digitally as I was going 55-60 MPH • *Check Engine light ON • *Red ‘Brake’ light ON • *ABS failed • *Distance sensors failed • *Stability control failed • *Electronic braking system failed • *Power steering failed • *Cruise control failed • *Mercedes PRE-SAFE failed • *Blind Spot Assist failed • *Lane Keeping Assist failed • *Adaptive Highbeam Assist failed • *Mileage was not displaying on the dash • Car would not shut off as I pushed the off button when I managed to eventually stop • *Climate temperature sensor reaching temps of 127 degrees Fahrenheit. Q2: I lost control of the vehicle while driving on the highway at relevant speeds. I was unable to safely stop for some time. If this had been at night, the issue would have been even more dangerous. This car has previously slammed on the brakes erroneously (no visually perceived danger of a forward collision). These previous brake slamming issues happened once in a traffic jam on the highway and once on a main road. Q3: Not that I know of or remember, no. Q4: Before this latest incident, I have previously left my car at the dealership’s workshop to be inspected for some relevant issues and concerns that I have had. It was there for almost 2 months on one occasion. Q5: There was only one warning lamp on the instrument cluster related to the collision prevention assist being inoperative. This message has been on the dash for maybe a year or more. The times it previously slammed on the brakes erroneously, no messages were on the dash.

• Jul 22, 2024FL
  Fuel/propulsion system

  The fuel pump assembly Seals leaked fuel into my vehicle and saturated the interior of my car

• Jul 10, 2024OH
  Electrical system

  I believe there is faulty wiring in the door speaker front passenger side. It causes crackling and humming. It lessens some when you turn ECO off. Concerned it could ignite a fire. Once told by dealer it’s caused by rain going into the door. Next time told that just to look at the problem would be around $600 because it has steel doors??

• Jun 4, 2024VA
  Engine · Exterior lighting · Structure › Body
  Dealership stated on 6/4/24 extensive rust and perforations on rear vehicle sub frame that can cause risk to driver of accident or injury. MBUSA is offering to replace sub frame part # 212 350 38 05. However dealership advised MBUSA is not offering to replace corroded brake lines or brake fluid…

  Dealership stated on 6/4/24 extensive rust and perforations on rear vehicle sub frame that can cause risk to driver of accident or injury. MBUSA is offering to replace sub frame part # 212 350 38 05. However dealership advised MBUSA is not offering to replace corroded brake lines or brake fluid exchange, and would need to come out of pocket. MBUSA failed to notify me of safety defect. Vehicle was purchased from MB of Arlington, VA in 4/2019 however dealership sold vehicle that is dangerous to drive. The vehicle also has additional safety defects such as a passenger tail light that does not work, and a license plate light not functioning. Dealership wants an additional $1500 to replace these (2) lights. Vehicle has low mileage at 60,000 and was purchased with 35,000 under MB CPO program. I am very disappointed in Mercedes Benz and have never had so many quality and safety issues with any of my prior E-Classes before. I contacted MBUSA and opened up a Executive Care Escalations Case [XXX}. There was no warning lights of the impending safety feature. The level of rust on the sub frame is horrifying, and this vehicle should never have been sold to me under MB CPO. In addition, the vehicle engine is leaking oil in multiple places and could catch fire in any moment. I have never seen so many issues on a vehicle with low mileage, especially with a Mercedes. Dealer is refusing to assist with cost, and wants 2K+ to replace engine gaskets. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• May 6, 2024VA
  Visibility/wiper
  Recently (April 2024) we've noticed water drops forming on the inside of the vehicle along the top of the front windshield after a rain. Pushing outward along the top inside of the windshield glass indicates some movement of the glass. This applies all along the top inside of the windshield and…

  Recently (April 2024) we've noticed water drops forming on the inside of the vehicle along the top of the front windshield after a rain. Pushing outward along the top inside of the windshield glass indicates some movement of the glass. This applies all along the top inside of the windshield and not just one spot or area. So far, we have only observed water drops and have not observed any water pooling or puddling yet. We have not yet contacted a dealer; however we have conducted online research that strongly suggests that the windshield urethane adhesive seal is failing. Additional online information suggests that Mercedes had identified windshield urethane adhesive seal batch issues with certain 2016 E350 models. There have been no warning lamps or indicators from the vehicle. We have not observed any vehicle performance issues other than hearing a slight general whistling sound while driving at highway speeds above 55 mph, but that has been unchanged for years so it is likely not related to the windshield seal. The vehicle currently has approximately 30,000 miles on the odometer, and we are the second owners, having purchased it as a certified pre-owned vehicle with about 10,000 miles.

• Feb 26, 2024FL
  Visibility › Windshield
  We have been getting water in the front passenger compartment below the door area, after rain. We took it to our mechanic, who determined that the windshield integrity has been compromised along the top area in front of the passenger dash. Apparently the seal has separated, allowing water to enter…

  We have been getting water in the front passenger compartment below the door area, after rain. We took it to our mechanic, who determined that the windshield integrity has been compromised along the top area in front of the passenger dash. Apparently the seal has separated, allowing water to enter the vehicle. Our mechanic stated that the safety of the vehicle has been compromised and the windshield needs to be removed and re-glued. We are currently waiting for an appointment with a glass specialist to have this repaired, as there does not seem to be a recall listed. Several months ago we had the drain(s) cleared and thought this would solve the problem, but it did not.

• Sep 13, 2023FL
  Structure › Body
  I received a letter from Mercedes-Benz USA LLC located at 1 Mercedes-Benz drive Sandy springs Georgia 30328 phone number 800-367-6372. This letter advised me of the extension of warranty coverage on the rear subframe of my vehicle to 20 years with unlimited mileage cover. I call my local Mercedes…

  I received a letter from Mercedes-Benz USA LLC located at 1 Mercedes-Benz drive Sandy springs Georgia 30328 phone number 800-367-6372. This letter advised me of the extension of warranty coverage on the rear subframe of my vehicle to 20 years with unlimited mileage cover. I call my local Mercedes dealership where I purchased the vehicle to inquire about the severity of this problem. I specifically inquired as to whether this presented a safety concern or not. I was advised that the rear sub frame is the mechanism that holds the rear end of the car to the frame which if deteriorated enough would cause the rear end to separate from the frame resulting in problems with maneuvering the vehicle. Once I was advised of this I requested an appointment to go in and have the rear sub frame inspected to see exactly where the deterioration stands on this vehicle. In my opinion this is a definite safety concern and should have been classified as a recall rather than just a warranty extension. I was granted an appointment to have my subframe inspected tomorrow afternoon for which I specifically requested whether I would be charged or not and was advised I would not. I request that this be looked into by your agency as I do consider this a real safety factor. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Aug 31, 2023AZ48,000 mi
  Fuel system, gasoline
  The contact owns a 2016 Mercedes-Benz E350. The contact stated that while the vehicle was parked and shut off inside the garage, there was an abnormally strong fuel odor detected. The vehicle was taken to the dealer, where it was diagnosed with a cracked fuel filter that needed to be replaced. The…

  The contact owns a 2016 Mercedes-Benz E350. The contact stated that while the vehicle was parked and shut off inside the garage, there was an abnormally strong fuel odor detected. The vehicle was taken to the dealer, where it was diagnosed with a cracked fuel filter that needed to be replaced. The vehicle was then taken to an independent mechanic, who replaced the fuel filter. The manufacturer was not made aware of the failure. The failure mileage was 48,000.

• Aug 23, 2023TXCrash1 injury
  Service brakes · Steering · Vehicle speed control
  I was driving my husband's 2016 E350 at 45 mph when the car accelerated. I attempted to control the speed by braking but the brake did not respond well. The steering wheel was also loose. The car sped up and turned left to the opposite side of the road, crossed the two lanes and hit the fence…

  I was driving my husband's 2016 E350 at 45 mph when the car accelerated. I attempted to control the speed by braking but the brake did not respond well. The steering wheel was also loose. The car sped up and turned left to the opposite side of the road, crossed the two lanes and hit the fence followed by a tree. The car was totaled, and the tree broke down at its branches. I survived the crush with two fractures on my back and on my left thumb.

• Jul 13, 2023MD39,000 mi
  Visibility › Windshield
  The contact owns a 2016 Mercedes-Benz E350. The contact stated that water was leaking from the front driver’s side windshield. The contact also stated that several months later, she became aware that the front passenger’s side windshield was leaking. An undisclosed dealer was notified of the…

  The contact owns a 2016 Mercedes-Benz E350. The contact stated that water was leaking from the front driver’s side windshield. The contact also stated that several months later, she became aware that the front passenger’s side windshield was leaking. An undisclosed dealer was notified of the failure and the contact was provided an estimate for the repair, but no further assistance was provided. The vehicle was then taken to a collision center where it was diagnosed that the windshield bonding had failed and needed to be replaced. The vehicle was repaired; however, the failure recurred. The manufacturer was notified of the failure and the contact was referred to the dealer. The contact was then referred to the NHTSA Hotline. The failure mileage was approximately 39,000.

• Jan 24, 2023NJ63,000 mi
  Electrical system › Ignition

  The contact owns a 2016 Mercedes-Benz E350. The contact stated while driving 30 MPH, the vehicle started shaking without warning. The vehicle was taken to the dealer for diagnostic test, and the mechanic stated that the ignition coil needed to be replaced. The vehicle was not repaired due to parts availability. The manufacturer was contacted and referred the contact to the dealer. The failure mileage was 63,000.

• Oct 27, 2022TX
  Electrical system · Forward collision avoidance › Warnings · Vehicle speed control
  I was driving on North Shepherd Drive in Houston, TX, at a speed of approximately 35 MPH. While I was lightly braking to slow down for an upcoming intersection where I wished to turn, the car flashed 2 error lights--Frontal Collision Avoidance System Inoperable, and Traction Control System…

  I was driving on North Shepherd Drive in Houston, TX, at a speed of approximately 35 MPH. While I was lightly braking to slow down for an upcoming intersection where I wished to turn, the car flashed 2 error lights--Frontal Collision Avoidance System Inoperable, and Traction Control System Inoperable. At that moment, the car began to accelerate out of my control. It began to accelerate at a pace comparable to a full-throttle acceleration. At that moment, I turned off the vehicle and coasted to the side of the road. After a moment, I turned the car back on, electrical components responded as normal. However, there was a fluttering movement on the RPM levels on the tachymeter--even at idle levels.

• Sep 3, 2022PA
  Unknown or other
  The car was in for (Aug 2022) annual safety and emissions state (PA) inspection and normal maintenance. Last performed Aug 2021. I was told that the car failed safety inspection because the Rear SubFrame had rusted through. A hole was present not just surface rust. The car has 58,000 miles and…

  The car was in for (Aug 2022) annual safety and emissions state (PA) inspection and normal maintenance. Last performed Aug 2021. I was told that the car failed safety inspection because the Rear SubFrame had rusted through. A hole was present not just surface rust. The car has 58,000 miles and garage kept. The car was just (June 2022) in for all 4 wheel brakes replaced along with 4 tires. There hasn’t been any recall on this and they quoted Repair price of$5,400 and expect me to pay $1,000 towards that replace and repair. My question is clearly this is an inferior part. I’ve since investigated that recalls have been issued for the C model but not on the E which I own. If my car was in for inspection 12 mos ago and in for brakes 3 mos ago how long did it take to rust through? We’re talking about a hole not surface rust. I can’t believe that the hole just appeared anyway but within the time last safety inspection occurred. Why do I maintain the service recommendations and have safety concern that the manufacture will not own up to and that me and my family are at risk of an accident. I’n fact the service manager admitted that he is seeing more and more of theses failures.

• Jul 14, 2022CA
  Unknown or other
  I have the similar issue with my sun roof as described by this entry found on your website below: Started developing (April 2021) a rattle in car's roof along with occasional metal popping sound coming from rear of car. Continued to get worse. Then rattle stopped for a while and so did the metal…

  I have the similar issue with my sun roof as described by this entry found on your website below: Started developing (April 2021) a rattle in car's roof along with occasional metal popping sound coming from rear of car. Continued to get worse. Then rattle stopped for a while and so did the metal popping sound. Now ( August, 2021)it sounds like there is a bolt loose in the sunroof area and the metal popping sound is really loud and I think coming from roof. Most of the time when car body twist, like going up a slight incline at an angle when entering a parking lot this incredible loud popping sound resonates throughout the entire car body. Played around on Mercedes website and it appears that Mercedes has problems with sunroof bolts coming loose. This is a safety defect -- if sunroof comes lose at 70 mph it is going to fly off and hurt or kill someone. Also strength of roof is compromised and if have accident where roof protection is needed it will probably fail.

• May 13, 2022ALCrash1 injury
  Air bags

  Someone ran a stop sign traveling at at least 30 mph and hit my car twice; once in the front, once in the rear. I hit my face on the steering wheel, was knocked unconscious, and received a concussion. The airbags never deployed.

• Apr 15, 2022TN
  Visibility/wiper

  Windshield separation from body of car causing water intrusion and water damage on headliner and electrical components.

• Jan 21, 2022CA107,000 mi
  Power train
  The contact owns a 2016 Mercedes-Benz E350. The contact stated while shifting between the lower gears, the vehicle would shift roughly resulting in the vehicle jerking while driving. The contact stated no warning light was illuminated. The vehicle was taken to a local dealer where it was diagnosed…

  The contact owns a 2016 Mercedes-Benz E350. The contact stated while shifting between the lower gears, the vehicle would shift roughly resulting in the vehicle jerking while driving. The contact stated no warning light was illuminated. The vehicle was taken to a local dealer where it was diagnosed with needing the transmission replaced. The vehicle was not repaired. The manufacturer was informed of the failure and informed the contact that the VIN was not under recall. The contact was transferred to the NHTSA for assistance. The failure mileage was approximately 107,000.

• Dec 1, 2021NJ
  Visibility/wiper
  My car's windshield at first started to leak. I took the car to the dealer and was informed that leaky windshields are not covered by the warranty. I took no further action as we were still in a COVID restricted environment and the need for the car was low. As my company started to return to the…

  My car's windshield at first started to leak. I took the car to the dealer and was informed that leaky windshields are not covered by the warranty. I took no further action as we were still in a COVID restricted environment and the need for the car was low. As my company started to return to the office I have begun using the car more and have now observed that windshield adhesion to the frame has now deteriorated. The car has approximately 41K miles at which I would not expect the windshield to be unglued. I was also recently made aware that there is a similar problem affecting other MB 2020 vehicles, which I do not find to be a coincidence. My car will now require a full windshield replacement and MB is refusing to discuss it.

• Nov 12, 2021AL55,000 mi
  Engine · Structure
  The contact owns a 2016 Mercedes-Benz E350. The contact stated that there was an oil burning odor present inside and outside of the vehicle. The vehicle was taken to the local dealer who diagnosed that the engine drive belts were faulty, and corrosion was present on the motor mounts. The vehicle…

  The contact owns a 2016 Mercedes-Benz E350. The contact stated that there was an oil burning odor present inside and outside of the vehicle. The vehicle was taken to the local dealer who diagnosed that the engine drive belts were faulty, and corrosion was present on the motor mounts. The vehicle was not yet repaired. In addition, the HVAC system was faulty causing mold and mildew to build up inside the vehicle. The manufacturer was not yet notified. The failure mileage was 55,000.

• Oct 7, 2021GA
  Engine

  Re-Seal Upper Timing Covers of the cylinder head timing covers are seeping. 2016 E350 has less thank 19k on it. The fluids can potentially leak onto the roads causing a hazard, it is also a fire hazard, as well as an environmental issue. This was identified by Revolution Mercedes in Decatur, GA. After reading some forums, I have seen where others are having similar issues and believe this should be addressed.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Desiccated Air Bag Inflator Rupture

  EA21002Opened Sep 17, 2021Open
  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…

  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11007750Complaint Dynamic seat function or multicontour system inoperative Noises from area of lateral support bladder Cause Lateral support bladder leaking Remedy Replacement of complete air cushion insert.
• 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
• 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
• 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
• 10235673To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut.
• 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10232334To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut. The purpose of this NCU update is to alert you that: 1. The settlement went into effect on January 23, 2023. Customers are now eligible to receive extended warranty coverage and may start contacting authorized Mercedes-Benz dealerships to schedule an appointment for the repairs. 2. Before scheduling a repair appointment and ordering replacement parts kits: The customer should be given a repair order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the repair order before the parts kit can be ordered.
• 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
• 10231042To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut. The purpose of this NCU update is to alert you that: 1. The settlement went into effect on January 23, 2023. Customers are now eligible to receive extended warranty coverage and may start contacting authorized Mercedes-Benz dealerships to schedule an appointment for the repairs. 2. Before scheduling a repair appointment and ordering replacement parts kits: The customer should be given a repair order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the repair order before the parts kit can be ordered.
• 10217216Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has extended the warranty for the accelerator pedal wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms).
• 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
• 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
• 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
• 10205265Outside mirror fogged.
• 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
• 10205239"Anti-theft protection activated".
• 10205237The COMAND unit does not start or the display remains dark.
• 10205236"Metadata loss- Please reimport all media data".
• 10205234Software update of COMAND Online control unit.
• 10205233Mobile phone cotacts are not transferred completely.
• 10205229No/poor radio reception in AM frequency range.
• 10205228No/poor radio reception in AM frequency range.
• 10205156Intial startup not possible after replacement of transmisson 725.0 or of electrohydraulic controller unit.
• 10205154Gasket may settle causing a slight oil leak.
• 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
• 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
• 10186142Unmotivated Reaction from Park Assist - model series 213 facelift / 238 facelift with option code 235 (active par- king assist) and option code 501 (surround view system)

Every Mercedes-Benz E350 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.