2005 Jeep Liberty
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Jeep › Liberty › 2005
These records cover every 2005 Jeep Liberty. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2005 Jeep Liberty. Newest first.
Chrysler (FCA US LLC) is recalling certain 2004-2007 Jeep Liberty vehicles. The rear suspension lower control arms can fracture due to excessive corrosion, causing a loss of vehicle control.
Risk and remedy
Risk
A fractured control arm can cause a loss of vehicle control, increasing the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will replace the rear lower control arms, free of charge. The recall began June 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U38. Note: This recall is an expansion of recall 12V-085. Vehicles included in that campaign are not included in this recall.
Chrysler Group LLC (Chrysler) is recalling certain model year 1993-1998 Jeep Grand Cherokee and 2002-2007 Jeep Liberty vehicles. The fuel tanks in these vehicles are at risk of failure and leakage in certain rear impacts.
Risk and remedy
Risk
A fuel leak in the presence of an ignition source may result in a fire.
Remedy
Owners may take their vehicles to dealers and the dealers will perform a free inspection of the rear structure. On vehicles in the recall that are not equipped with a tow hitch, Chrysler will install a Chrysler designed tow hitch free of charge, provided the condition of the vehicle can support proper installation. On vehicles in the recall that are equipped with an aftermarket tow hitch, Chrysler will assess whether the hitch and surrounding areas show evidence of sharp edges or other puncture risks. If so, Chrysler will replace the tow hitch with a Chrysler designed tow hitch free of charge, provided the condition of the vehicle can support proper installation. On vehicles already equipped with a Chrysler designed tow hitch, Chrysler will inspect the area around the tow hitch installation, and if any installation issues are identified, they will be repaired free of charge. The recall began on August 1, 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign numbers are N45 (for the Grand Cherokee vehicles) and N46 (for the Liberty vehicles).
Timken is recalling certain non-formed, front wheel hubs, part number HA599467, which were sold to retail and automotive distributors in the automobile aftermarket as front wheel hub replacements designed only for use on certain 2002 through 2005, 4X4, non-ABS, Jeep Liberty vehicles. These front wheel hub units can be mistakenly sold to owners and…
Risk and remedy
Risk
If the non-formed hub unit is installed on a Jeep Liberty 4x2 model (which does not use an axle nut for hub retention), the vehicle wheel will not be secure and a front wheel separation may occur, increasing the risk of a crash.
Remedy
Timken has notified retail stores that have received the subject parts. The front wheel hubs will be replaced free of charge. Owners who may have purchased the affected units should contact Timken at 1-330-471-3693 for more information. This recall is being conducted by Timken, not Chrysler/Jeep.
In june 2012, chrysler expanded this recall to include model year 2006 and 2007 jeep liberty vehicles, representing an additional 137,176 vehicles. this recall now concerns certain my 2004-2007 jeep liberty vehicles. the total number vehicles being recalled IS now 346,900. these vehicles were manufactured from july 3, 2003 through june 29, 2007. the…
Risk and remedy
Risk
A fracture of the rear lower control arm may result in a loss of vehicle control and may lead to a vehicle crash.
Remedy
Chrysler will notify owners, and dealers will replace the rear lower control arms on all affected vehicles originally sold in, or currently registered in, connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin, and the district of columbia, free of charge. the safety recall began on march 26, 2012. owners may contact chrysler at 1-800-853-1403.
Rock krawler IS recalling 44 performance suspension systems sold as aftermarket equipment for use on the vehicle listed above. these suspension systems were produced with grade 2 carriage bolts instead of the proper grade 5 carriage bolts. the improper grade 2 carriage bolts could experience a loss of clamping force for the bottom strut fork.
Risk and remedy
Risk
This condition could cause a loss of effective lift and lowering of the affected vehicle, possibly creating the driver to panic which could possibly lead to a vehicle crash.
Remedy
Rock krawler will notify owners and provide a free remedy. the safety recall began on october 15. 2008. all the affected untits have been remedied. owners may contact rock krawler at 1-518-270-9822.
On certain trucks, the constant tension front lower ball joints may experience contamination. if the vehicle IS operated for an extended period with this condition, the ball joint may eventually experience wear and looseness.
Risk and remedy
Risk
When the driver continues to operate the vehicle with this condition, the contamination can lead to corrosion, accelerated wear and possibly separation from the steering knuckle causing a loss of vehicle steering control increasing the risk of a crash.
Remedy
Dealers will replace the front lower ball joints free of charge. the recall began on september 11, 2006. Owners should contact daimlerchrysler at 1-800-853-1403.
Certain pro-a motors corner lamps, turn signals, and headlights sold as replacement lamps for use on certain passenger vehicles listed above. some combination lamps that are not equipped with amber side reflectors fail to conform to federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment.
Risk and remedy
Risk
Without the amber reflectors, the vehicle will be poorly illuminated, possibly resulting in a vehicle crash without warning.
Remedy
Pro-a motors will notify owners and offer to repurchase the lamps. the recall began on april 3, 2006. owners may contact pro-a motors at 323-838-2988.
On certain pickup trucks, sport utility and passenger vehicles equipped with 42rle automatic transmissions, the cup plug that retains the park pawl anchor shaft may be improperly installed. if the shaft moves out of position, the vehicle may not be able to achieve 'park' position.
Risk and remedy
Risk
If this occurs and the parking brake IS not applied, the vehicle may roll away and cause a crash without warning.
Remedy
Dealers will inspect the transmissions and install a bracket to ensure the park pawl anchor shaft IS retained in the proper position. the recall began on november 28, 2005. owners may contact daimlerchrysler at 1-800-853-1403.
Owner complaints
1,118 complaints73 involved a crash27 involved a fire53 injuries5 deaths
What owners report most
Latest complaints
- Unknown or other
i recieved the car from a private party and he stated no issues but since older car and now registration is due it states theres still an open recall is this vehicle still covered for it?
- Power train · Suspension
The ball joint broke while I was driving I lost all control of vehicle
- Power train · Suspension
The contact owns a 2005 Jeep Liberty. The contact stated that while driving at an undisclosed speed, the contact noticed an abnormal sound coming from the vehicle, and the vehicle was shaking erratically. No warning lights were illuminated. The vehicle was towed to the dealer, where it was…
The contact owns a 2005 Jeep Liberty. The contact stated that while driving at an undisclosed speed, the contact noticed an abnormal sound coming from the vehicle, and the vehicle was shaking erratically. No warning lights were illuminated. The vehicle was towed to the dealer, where it was diagnosed with transfer case and transmission failure. The contact was informed that the transfer case and the transmission needed to be replaced. The vehicle was in the process of being repaired. The contact researched NHTSA Campaign Number: 18V278000 (Suspension). The manufacturer was made aware of the failure and a case was filed. The contact was advised to submit the repair documents regarding the failure. In addition, the contact was informed that the replacement of the transfer case and the transmission replacement were not covered under the recall. The contact was advised to contact the NHTSA Hotline and report the failure. The failure mileage was approximately 200,000.
- Steering
Today 6/16/2025 I’m having trouble turning to the right and left leaving from a stop sign we checked to be sure power steering fluid is full and it is. The person who checked the power steering fluid level, said that there is rubber grommets under the hood with the suspension and staring that look…
Today 6/16/2025 I’m having trouble turning to the right and left leaving from a stop sign we checked to be sure power steering fluid is full and it is. The person who checked the power steering fluid level, said that there is rubber grommets under the hood with the suspension and staring that look like they are all decayed or dry rotted. I have not had a problem with it breaking yet, but I’m sure that’s coming. Not sure it’s safe to drive.
- Suspension
I was driving on a bridge and my ball joint broke. Blew a hole through my tire and my rim and the fender flare blew off. I had had that same ball joint replaced approximately two years prior maybe sooner. I got this Jeep in 2017 and I have replaced the driver side ball joint twice the passenger side ball joint once and the ball joints look bad again.
- Steering · Suspension · Wheels
About 6 months ago the passenger side front end to hit the ground, just after going 60 miles an hour thankfully turning in daughter's driveway. Lower ball joint passenger side came apart. On Monday doing 35 mph the driver side hits the pavement hard! Luckily I ditched in a driveway on the left! The…
About 6 months ago the passenger side front end to hit the ground, just after going 60 miles an hour thankfully turning in daughter's driveway. Lower ball joint passenger side came apart. On Monday doing 35 mph the driver side hits the pavement hard! Luckily I ditched in a driveway on the left! The tire slammed into the fender well breaking the plastic there and the piece that goes back under the doors? Ball joint broke completely into? I'm on my third day of working in the rain alongside a road repairing this?
- Suspension
The contact owns a 2005 Jeep Liberty. The contact stated while driving approximately 70 MPH, the vehicle swerved to the left across three lanes of traffic and the contact turned the steering wheel to the right to prevent the vehicle from veering to the left. The contact then stopped on the shoulder…
The contact owns a 2005 Jeep Liberty. The contact stated while driving approximately 70 MPH, the vehicle swerved to the left across three lanes of traffic and the contact turned the steering wheel to the right to prevent the vehicle from veering to the left. The contact then stopped on the shoulder of the highway. The contact stated there was no warning light illuminated. The contact stated that the Police were on scene and determined that the vehicle could not be driven. The contact stated the Police Officer picked up the ball joint that had detached from the driver’s side front suspension of the vehicle. The vehicle was towed to the residence. The vehicle had not been taken to a dealer or independent mechanic. The vehicle was not diagnosed or repaired. The contact researched online and related the failure to NHTSA Campaign Number: 06V288000 (Suspension). The manufacturer was not informed of the failure. The failure mileage was approximately 225,000.
- Tires
P235/70R16 The car was parked, when I left on the morning of July 14 to go to work, it had already exploded. I thought it was the excess heat but the strange thing was the separation that occurred.
- Seats
While driving on a long trip, a burning smell was noticed. The heated seats had not been turned on, as they are rarely used & the indicator light for the heated seats was not on. When the driver stopped to inspect, the back of the seat had burned through the lumbar support pillow. The seat is…
While driving on a long trip, a burning smell was noticed. The heated seats had not been turned on, as they are rarely used & the indicator light for the heated seats was not on. When the driver stopped to inspect, the back of the seat had burned through the lumbar support pillow. The seat is severely charred and damaged through the inner foam layer of the seat. The seat will need to be replaced. The driver could have been seriously injured if the seat had caught fire. Jeep was notified, but expressed absolutely no concern & offered no assistance. An online review revealed that this is a known problem for Chrysler/Jeep (in particular Jeep Liberty) and there have been severe injuries. How many instances must occur before a safety recall occurs? We had no idea that this safety concern existed prior to our own experience.
- Steering · Suspension · Wheels
Lower ball joints gave out on driver’s side while turning, snapping the wheel/tire from the car and dropping vehicle down abruptly. Dealership who fixed the lower control arm and hitch recalls, did not fix and said there was no Lower Ball Joint recall- which was a confirmed recall and lead to vehicle damage and safety hazard
- Unknown or other
The connection "bolt" { situated under the vehicle} between the transmission Shift lever and the rod responsible for actually shifting between park, neutral,, forward and reverse transmission gears completely` rusted away.( See attached picture) causing a complete disconnect rendering the gear…
The connection "bolt" { situated under the vehicle} between the transmission Shift lever and the rod responsible for actually shifting between park, neutral,, forward and reverse transmission gears completely` rusted away.( See attached picture) causing a complete disconnect rendering the gear shift lever useless. The component is available for inspection upon request? It was shear luck that I was in slow city driving when I realized that the vehicle was damaged and not drivable. Until a final repair is made the vehicle is "dead in the water" so to speak. If this failure occurred during a trip, in an isolated place, I would have been abandoned and helpless as soon as I stopped. The fact that the "bolt" situated under the chassis was made of metal that rusted is incomprehensible to me, especially in a vehicle that is sold as suitable for "rough riding" over rocky terrain, through streams and generally roughing it. Common sense dictates that this critical part should have been constructed of sturdier stuff , not metal that rusts. The problem has not been reproduced or confirmed by a dealer or independent service center? I can't afford to have it repaired at this time. The vehicle or component has not been inspected by the manufacturer, police, insurance representatives or others. There were no warning lamps, messages or other symptoms of the problem prior to the failure.
- Suspension
The contact owns a 2005 Jeep Liberty. The contact stated while driving approximately 10 MPH, the suspension suddenly failed, causing the front end of the vehicle to drop down and the vehicle became undrivable. The vehicle was towed to an independent mechanic where it was diagnosed that the front…
The contact owns a 2005 Jeep Liberty. The contact stated while driving approximately 10 MPH, the suspension suddenly failed, causing the front end of the vehicle to drop down and the vehicle became undrivable. The vehicle was towed to an independent mechanic where it was diagnosed that the front driver's side lower ball joint had failed. The vehicle was not repaired. The local dealer was notified of the failure but did not offer any assistance. The manufacturer was not notified of the failure. The failure mileage was approximately 157,000.
- Structure › Body
I have a 2005 Jeep liberty renegade, there was recall issued (N46 Trailer Hitch recall) I contacted Chrysler Customer Care. they sent me this, [XXX] Hello [XXX] Thank you for contacting Jeep Customer Care. We have received your email stating you are about to purchase this 2005 Jeep Liberty and…
I have a 2005 Jeep liberty renegade, there was recall issued (N46 Trailer Hitch recall) I contacted Chrysler Customer Care. they sent me this, [XXX] Hello [XXX] Thank you for contacting Jeep Customer Care. We have received your email stating you are about to purchase this 2005 Jeep Liberty and understand your concern with a recall that has not been completed. We are happy to look into this for you. After review of the vehicle information we have found that the N46 Trailer Hitch recall has not been completed. Jeep attempts to perform recall repairs regardless of the vehicle age or the recall issue date. Any authorized dealership will be happy to repair the vehicle within the terms of the recall at no charge to you. Please contact us at [XXX] if you require additional assistance. Best wishes, [XXX] Jeep Customer Care I contacted Pine Belt of Lakewood NJ and got this response [XXX] Wed, Jan 19 at 1:13 PM We can not work on this vehicle at this time because we are not taking new customers . [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
- Steering · Suspension
I was traveling on the highway at about 60 mph, hit a small bump in the highway and nearly lost total control. Pulled over and came to a complete stop. Re-entered the highway and nearly lost control even at a slower speed, 55mph.
- Suspension
Slowly crossed railroad tracks ball joint came disconnected forcing disconnection of the front drive shaft
- Suspension
The contact owns a 2005 Jeep Liberty. The contact stated while driving approximately 10 MPH, the front driver’s side wheel detached from the vehicle. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 06V288000 (Suspension). The vehicle was repaired but continued to…
The contact owns a 2005 Jeep Liberty. The contact stated while driving approximately 10 MPH, the front driver’s side wheel detached from the vehicle. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 06V288000 (Suspension). The vehicle was repaired but continued to experience the same symptoms. The vehicle was towed to a local dealer. The manufacturer was informed of the failure but was unable to assist. The failure mileage was approximately 75,000.
- Suspension · Wheels
I have a 2005 Jeep Liberty Sport. I was backing out of my driveway when I heard a crunching sound. I got out of the car and saw that the passenger side of my car was much lower than the driver's side. I noticed that their was windshield wiper fluid pouring out of the front end. Upon inspection, I…
I have a 2005 Jeep Liberty Sport. I was backing out of my driveway when I heard a crunching sound. I got out of the car and saw that the passenger side of my car was much lower than the driver's side. I noticed that their was windshield wiper fluid pouring out of the front end. Upon inspection, I noticed that the ball joint had snapped and the control arm was almost on the ground. Had I been able to get to the freeway as planned, I could have been seriously injured. I called to verify recall information and was informed that the ball joint recall issue had been resolved. However, with further investigation, it seems that this issue is happening after the repairs as well. I have attached pictures. [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
- Electrical system · Unknown or other · Visibility/wiper
The rear window latch does not work. It will not open to latch the window closed with the back door. The window then opens when driving. I have a bungee cord holding my window closed. So anyone can enter my vehicle and it moves when I stop or go. I am ot able to use my back door due to having to…
The rear window latch does not work. It will not open to latch the window closed with the back door. The window then opens when driving. I have a bungee cord holding my window closed. So anyone can enter my vehicle and it moves when I stop or go. I am ot able to use my back door due to having to redo it everytime. My driverside door also does not lock or unlock all the doors when I press the lock or unlock button. I have to open my door and shut off jeep and try numerous times for ot to work.
- Suspension
The contact owns a 2005 Jeep Liberty. The contact stated the recall repair of NHTSA Campaign Number: 18V278000 (Suspension) was completed. The contact stated while driving 35 MPH, she heard abnormal sounds coming from the rear-end of the vehicle. The vehicle was taken to an independent mechanic who…
The contact owns a 2005 Jeep Liberty. The contact stated the recall repair of NHTSA Campaign Number: 18V278000 (Suspension) was completed. The contact stated while driving 35 MPH, she heard abnormal sounds coming from the rear-end of the vehicle. The vehicle was taken to an independent mechanic who diagnosed that the rear upper and lower ball joints needed to be replaced. The dealer was not notified of the failure. The manufacturer was notified of the failure but did not provide any assistance. The vehicle was repaired. The approximate failure mileage was 9,000.
- Suspension
In the past 15 months (recently as last week) I've had to replace the ball joints in the front end. We are the original owner and have the same address when purchased. I see there was a recall notice but i was never informed. NHTSA Recall #06V288000. The repair on 9/210/21 repair was a total of $516.00. The repair in 6/2020 was $516.00 as well. Lower ball joint - $136 Upper control arm - $130 Labor - $250
- Suspension
Reversing out of a driveway went to turn wheel heard loud pop snap front passenger side went to ground fender popped lose discovered by tow that the lower ball joint had snapped and possible lower control arm
- Suspension · Wheels
Right upper ball joint control arm collapsed while in the drive-through at McDonald's could not move the car turn it or do anything it completely collapsed on the front right side due to corrosion of the lower ball joint and then I know this has been recalled however my car is not under the recall and I don't understand why because it was the same exact issue it's a Jeep Liberty
- Steering · Suspension · Wheels
Drivers side lower ball joint catastrophic failure with no warning signs evident except split boot(s). Separation/break from upper control arm, tie rod and steering assembly at low speed reverse. NHTSA Recall ID: 06V288000 (Daimler-Chrysler Notification Code: F23) of lower ball joints performed by…
Drivers side lower ball joint catastrophic failure with no warning signs evident except split boot(s). Separation/break from upper control arm, tie rod and steering assembly at low speed reverse. NHTSA Recall ID: 06V288000 (Daimler-Chrysler Notification Code: F23) of lower ball joints performed by Chrysler authorized dealer/repair station 2007. Dealer contacted two (2) weeks prior to incident to coordinate possible re-repair and/or consideration of faulty OEM parts used in original recall. Consumer stated gas smell around his car and inside. *JB
- Steering · Suspension
The contact owns a 2005 Jeep Liberty. The contact stated while driving 35 mph, the steering wheel would shake with the vehicle wobbling. The contact stated that the vehicle was out of alignment. The contact informed the original owner of the failure, who then took the vehicle to an independent…
The contact owns a 2005 Jeep Liberty. The contact stated while driving 35 mph, the steering wheel would shake with the vehicle wobbling. The contact stated that the vehicle was out of alignment. The contact informed the original owner of the failure, who then took the vehicle to an independent mechanic who diagnosed that the ball joint was faulty, but only performed an alignment. The failure recurred. The dealer was made aware of the failure but did not diagnose or repair the vehicle. The manufacturer was made aware of the failure and referred the contact to file a complaint with the NHTSA. The failure mileage was 98,500.
- Steering · Suspension › Front › Control arm › Lower ball joint
The contact owns a 2005 Jeep Liberty. The contact stated that while reversing and making a left turn, the front driver’s side ball joint fractured and the lower control arm detached. The steering wheel also shook and jerked while driving approximately 50 mph. The vehicle was towed to the residence.…
The contact owns a 2005 Jeep Liberty. The contact stated that while reversing and making a left turn, the front driver’s side ball joint fractured and the lower control arm detached. The steering wheel also shook and jerked while driving approximately 50 mph. The vehicle was towed to the residence. The dealer was made aware of the failure and informed the contact that there was a recall repaired in 2006, for the ball joints. The vehicle was not diagnosed nor repaired. The manufacturer was not made aware of the failure. The failure mileage was 102,000.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Crash Related Fuel Tank Fires
ODI has completed an extensive analysis of rear crash fuel tank system integrity data for the subject Jeep Cherokee, Grand Cherokee and Liberty vehicles (SVs).As of June 2013, ODI knew of 56 post-collision fatal fires, 28 non-fatal fires, and 6 fuel leak incidents (totaling 90 incidents, 75 fatalities and 58 injuries)…
ODI has completed an extensive analysis of rear crash fuel tank system integrity data for the subject Jeep Cherokee, Grand Cherokee and Liberty vehicles (SVs).As of June 2013, ODI knew of 56 post-collision fatal fires, 28 non-fatal fires, and 6 fuel leak incidents (totaling 90 incidents, 75 fatalities and 58 injuries) involving the SVs.Based on this analysis, ODI issued a Recall Request Letter (RRL) on June 3, 2013 requesting that Chrysler recall the Grand Cherokee and Liberty vehicles due to the rate of fatal, non-fatal fire, and fuel leak incidents when compared to peer vehicles (compact and medium SUVs) built during the same time period.In the RRL, ODI described how the location of the aft-mounted fuel tank made the SVs vulnerable to rear impact crash fuel tank failures.During the analysis, besides the high speed/high severity crashes present in both the SV and peer vehicles, ODI observed a significant number of low and moderate speed rear impact crash related fires and leaks, particularly in the Liberty.The data also demonstrated that SVs originally equipped with towing hitch receivers (trailer hitches) appeared to be under-represented in rear-impact related fuel tank failures.In the RRL, ODI requested that Chrysler provide its response by June 18, 2013, otherwise NHTSA might proceed to an Initial Decision that the SVs contain a safety-related defect.Chrysler responded to the RRL on June 4, 2013 and vigorously disputed the tentative findings of the RRL.Among other things, Chrysler argued that the SVs had an overall safety record superior to their peers, met or exceeded all applicable federal motor vehicle safety standards (FMVSS) and only experienced fires in severe high energy rear impacts.Nonetheless, while continuing to maintain that the SVs did not contain a safety-related defect, Chrysler proposed a recall (13V-252) of approximately 2.5M (1.6M currently registered) model year (MY) 1993 - 1998 Grand Cherokee (ZJ) and MY 2002-2007 Liberty (KJ) vehicles on June 18, 2013.The recall remedy submitted by Chrysler would employ a hitch receiver assembly consisting of a steel cross-member behind the fuel tank with forward-projecting arms bolted to the frame rails on either side of the fuel tank.For the MY 1999 - 2004 Grand Cherokee, Chrysler indicated it would conduct a customer satisfaction campaign and inspect vehicles equipped with aftermarket tow hitch receivers, and if necessary, replace any such hitch receivers whose conditionmay increase the risk of fuel system failure in rear crashes.Examination of the available data established that the MY 1999 - 2004 Grand Cherokee did not pose the same magnitude of safety risk as the MY 1993 - 1998 Grand Cherokee and MY 2002-2007 Liberty, particularly in low and moderate speed rear impacts.Because the agency has concluded that the vehicles do not present an unreasonable risk to safety, ODI is closing its investigation of the MY 1999 - 2004 Grand Cherokee.Although it was not within the scope of the Petition initiating this investigation or the Preliminary Evaluation preceding this EA, ODI also examined the performance of the MY 1993 - 2001 Cherokee as part of this investigation.NHTSA's assessment of the available data for the Cherokee did not establish an unreasonable risk in comparison to peer vehicles.ODI does not approve proposed defect remedies.While offering to install hitch receiver assemblies on the MY 1993-1998 Grand Cherokees and 2002-2007 Liberty, Chrysler did not, in ODI's view, provide enough evidence demonstrating the effectiveness of the proposed remedy in rear impacts.The Complete Summary for this Closing Resume (EA12-005) can be seen by
- Rear Suspension Control Arm Failure
In a letter dated March 2, 2012 Chrysler Group LLC (Chrysler) submitted a Defect Information Report (NHTSA recall No. 12V-085) to the NHTSA identifying a safety defect regarding rear suspension lower control arm corrosion in approximately 210,000 model year (MY) 2004 and 2005 Jeep Liberty vehicles, originally sold or…
In a letter dated March 2, 2012 Chrysler Group LLC (Chrysler) submitted a Defect Information Report (NHTSA recall No. 12V-085) to the NHTSA identifying a safety defect regarding rear suspension lower control arm corrosion in approximately 210,000 model year (MY) 2004 and 2005 Jeep Liberty vehicles, originally sold or currently registered in a Salt-belt state (Connecticut, Delaware, Iowa, Illinois, Indiana, Kentucky, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia).According to Chrysler, excessive corrosion could result in fracture of a rear suspension lower control arm which may result in a loss vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Chrysler, ODI identified 54 non-duplicative reports alleging failure of one or both rear lower control arms due to excessive corrosion.Thirteen of these complaints allege that the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional 11 complaints reported difficulty maintaining control of the vehicle when the rear lower control arm failed.All of the complainant vehicles were either originally sold or registered at the time of the incident in a Salt-belt state.ODI did not identify any reports (complaints or warranty claims) related to rear lower control failure due to excessive corrosion in the approximately 138,000 MY 2004 and 2005 Liberty vehicles that are not included in this recall (i.e., not sold or currently registered in a Salt-belt state).In Chrysler?s Defect Information Report, Chrysler stated that during the investigation a field survey of MY 2004 and 2005 Jeep Liberty vehicles was conducted.In total, Chrysler is aware of 83 incidents alleging rear control arm fracture (including complaints and field study results).Based on Chrysler?s decision to conduct a safety recall this investigation is closed. The associated VOQs are: 10449912, 10448981, 10448406, 10448119, 10447069,10446737, 10445029, 10443863, 10443222, 10441248, 10438681, 10437308, 10436416, 10436231, 10436024, 10434927, 10434157, 10433963, 10430852, 10429346, 10428006, 10427087, 10426644, 10426393, 10419094, 10417697, 10416623, 10410148, 10409668, 10402048, 10397413, 10392160, 10388448, 10365118, 10360057, 10360049, 10345985
- Rear Suspension Control Arm Failure
During Preliminary Evaluation (PE11-013), the Office of Defects Investigation (ODI) conducted an analysis of consumer field data from its Vehicle Owner Questionnaire (VOQ) database and from complaint data submitted to ODI by Chrysler. ODI's analysis of VOQ data identified 13 complaints alleging failure of either the…
During Preliminary Evaluation (PE11-013), the Office of Defects Investigation (ODI) conducted an analysis of consumer field data from its Vehicle Owner Questionnaire (VOQ) database and from complaint data submitted to ODI by Chrysler. ODI's analysis of VOQ data identified 13 complaints alleging failure of either the right or left rear lower control arm due to excessive corrosion.All of these complaints were associated with vehicles originally sold or registered in a salt belt state (for the purposes of this investigation, 'salt belt' includes Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia).All of the complaints were associated with vehicles manufactured in model years (MY) 2004 or 2005. Three of these complaints also allege a loss of vehicle control due to the rear lower control arm failure. No complaints related to the alleged defect were identified on vehicles manufactured during MYs 2002 or 2003. Similarly an analysis of Chrysler complaint data identified 11 complaints (2 of which are duplicative of VOQs) alleging failure of a rear lower control arm due to excessive corrosion.All 11 of these complaints were from consumers operating vehicles in a salt belt state and vehicles manufactured in either MY 2004 or 2005. Three of these complaints (not duplicative of VOQs) also allege a loss of vehicle control due to the rear lower control arm failure.The original scope of PE11-013 included MY 2002 through 2005 Jeep Liberty vehicles as they were in the same generation.In response to an Information Request (IR) letter sent by ODI, Chrysler provided information and sample components identifying a substantial design change of the rear lower control arms after MY 2003 and beginning with MY 2004.Analysis of complaint data from both data sources (ODI and Chrysler) did not identify any applicable complaints (lower control arm failures due to excessive corrosion) from vehicles manufactured during MY 2002 or 2003.Similarly no complaints from either data source were found in states outside of those identified as salt belt states.Chrysler stated in its IR letter response that its investigation and analysis is ongoing to determine the scope, possible root causes of the unusual lower control arm corrosion, and define possible consequences to motor vehicle safety. Based on ODI's data analysis from both sources (ODI and Chrysler data), this investigation has been upgraded to an Engineering Analysis (EA11-013) focused on vehicles originally sold or registered in a salt belt state and produced during MY 2004 and 2005, to further assess the scope and potential safety consequences of the alleged defect.
- Diesel fuel leak
Overheating of the electrical connector at the fuel heater on the fuel filter / water separator assembly can cause a fuel leak through the electrical connection.operators report the smell of diesel fuel, smoke, difficulty starting and/or poor engine operation.the fuel leakage IS reported by some operators as seepage…
Overheating of the electrical connector at the fuel heater on the fuel filter / water separator assembly can cause a fuel leak through the electrical connection.operators report the smell of diesel fuel, smoke, difficulty starting and/or poor engine operation.the fuel leakage IS reported by some operators as seepage, wetness, several drops, and an oz per minute.evidence of overheating of the connection was observed by some operators and reported as burned or discolored electrical connection at the fuel heater.seven operators report smelling or seeing smoke.one reported a vehicle engine compartment fire however the cause of the fire was not identified, and linkage of the fire cause to this issue IS not likely to be established.the location of the fuel filter / water separator assembly IS not near the location of the turbo charger which IS located on the opposite side of the engine.the turbo charger would present a potentially hot surface however due to the layout of the engine compartment and its components, diesel fuel leakage from the electrical connection would not likely migrate to the turbo charger.at this time, a safety-related defect trend has not been identified and this investigation IS closed.the closing of this investigation does not constitute a finding by nhtsa that a safety defect does not exist.the agency reserves the right to take further action if warranted by the circumstances.
- Front suspension ball joint separation
On january 6, 2006, the office of defects investigation (odi) opened a preliminary evaluation to investigate alleged front suspension lower ball joint separationin certain model year (my) 2004 jeep liberty vehicles.odi sent a letter to the manufacturer on february 7, 2006 requesting information about these and other…
On january 6, 2006, the office of defects investigation (odi) opened a preliminary evaluation to investigate alleged front suspension lower ball joint separationin certain model year (my) 2004 jeep liberty vehicles.odi sent a letter to the manufacturer on february 7, 2006 requesting information about these and other jeep liberty vehicles.consequently, the investigation was upgraded to an engineering analysis on may 31, 2006 and the range of subject vehicles under investigation was expanded to include all my 2002-2006 jeep liberty vehicles.odi IS aware of 566 non-duplicative complaints alleging involuntary front suspension lower ball joint separation in the subject vehicles.odi IS also aware of one non-injury crash and three alleged injury incidents (two crash incidents and one non-crash incident) related to the alleged defect resulting in minor injuries.the complaint counts reported above only include those my 2002-03 liberty vehicles where the alleged ball joint separation occurred after prior recall repairs were performed (see below) or if the vehicle was not included in the prior recall.the manufacturer conducted a prior safety recall (03v-460) to address the subject issue in certain my 2002-03 jeep liberty vehicles.according to daimlerchrysler?s november 4, 2003, defect information report (submitted in accordance with 49 cfr part 573), ?the constant tension lower control arm ball joints may experience a loss of lubrication which can lead to corrosion, accelerated wear and possibly separation from the steering knuckle.a constant tension ball joint which has separated from the knuckle may result in loss of vehicle directional control with minimal advanced warning.?however, evidence indicates that some vehicles serviced under recall 03v-460 continued to experience involuntary ball joint separations.the manufacturer has made numerous changes in the design, material composition, manufacture, quality control, supply, and installation of the subject ball joints since the prior safety recall was initiated in an effort to improve performance with respect to sealing, lubrication, and joint retention capability.by letter dated august 1, 2006, daimlerchrysler corporation has notified the agency that it will conduct a safety recall to address potentially defective front suspension lower control arm ball joints in approximately 826,687 model year 2002-2006 jeep liberty vehicles manufactured between january 2, 2001 and march 15, 2006, includingall vehicles subject to the prior recall.the nhtsa campaign number assigned to this recall IS 06v-288 (daimlerchrysler recall campaign f23).daimlerchrysler will replace both left and right front suspension lower control arm ball joints with improved components free of charge.accordingly, this investigation IS closed.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10229910Towing Capacity For Vehicles Modified With N45 Or N46 Trailer-Hitch Assembly This bulletin specifies the approved tow rating for vehicles not equipped with trailer tow package that have received a trailer-hitch assembly as a result of the N45 or N46 Campaign.
- 10229877Part Description: wheel hub cap Issue Description: This hubcap is installed directly to the wheel using screws; PN 00154236. This part is not currently listed in the catalog
- 10229256KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221686KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10221079Towing Capacity For Vehicles Modified With N45 Or N46 Trailer-Hitch Assembly This bulletin specifies the approved tow rating for vehicles not equipped with trailer tow package that have received a trailer-hitch assembly as a result of the N45 or N46 Campaign.
- 10221045Part Description: wheel hub cap Issue Description: This hubcap is installed directly to the wheel using screws; PN 00154236. This part is not currently listed in the catalog
- 10220840Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220471Mechanical rocker arm, intake, 1.7 ratio.
- 10220409Chrysler will offer owners an upgrade to the rear structure of the subject vehicles by the addition of a trailer hitch to better manage the crash forces in low-speed impacts.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10217728Generic Powertrain Control Module (PCM) Procedure This bulletin involves programming a generic PCM with software.
- 1021641605174039A$, 05072384A$, 05072138A$ - A/C Pressure Transducer For vehicles calling out AC Pressure Transducer Kit 05072138AA as a service part but built with different mating wiring connector (round) - also order connector repair kit 05019958AA (square).~ 2007MY RAM Trucks equipped with 6.7L Cummins turbo diesel engine only: If the A/C pressure transducer requires replacement, use part number 05072138AA that has a rectangular shaped electrical connector. If the engine wiring harness has a circular wiring connector, use jumper harness 68028774AA to change it to a rectangular connector.~ 6.7L RAM trucks built before10/17/2006 has pressures transducers (p/n 05191766AA) with a round connector that should have been changed per RRT 06- 068 to a rectangular transducer.~ 2001-2008 KJ, K1, ND.~
- 10191460Valve Body. These may cause over drive cycling.
- 10191442Mechanical rocker arm, intake, 1.7 ratio.
- 10189177Chrysler will offer owners an upgrade to the rear structure of the subject vehicles by the addition of a trailer hitch to better manage the crash forces in low-speed impacts.
- 10176210This SKU is a Ball Joint. The customer communication requested return of unsold inventory to inspect the cup material. Plastic cup material has the potential to have a shorter service life than the metal. Shorter service life will require the part be replaced sooner than its metal counterpart.
- 10176209This SKU is a Ball Joint. The customer communication requested return of unsold inventory to inspect the cup material. Plastic cup material has the potential to have a shorter service life than the metal. Shorter service life will require the part be replaced sooner than its metal counterpart.
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10141243Generic Powertrain Control Module (PCM) Procedure This bulletin involves programming a generic PCM with software.
- 10139909Towing Capacity For Vehicles Modified With N45 Or N46 Trailer-Hitch Assembly This bulletin specifies the approved tow rating for vehicles not equipped with trailer tow package that have received a trailer-hitch assembly as a result of the N45 or N46 Campaign.
- 10139875Part Description: wheel hub cap Issue Description: This hubcap is installed directly to the wheel using screws; PN 00154236. This part is not currently listed in the catalog
- 10136886New Safety Recall Advanced Communication ? N45062013 During recent discussions, the National Highway Traffic Safety Administration (?NHTSA?) and Chrysler Group LLC (?Chrysler?) mutually identified an opportunity to incrementally improve the performance of 1993 through 1998 model year Jeep Grand Cherokee vehicles and 2002 through 2007 model year Jeep Liberty vehicles in certain low-speed impacts. Chrysler has decided to conduct a voluntary safety recall to respond to customer concerns about that assessment. Chrysler will offer owners an upgrade to the rear structure of the subject vehicles by the addition of a trailer hitch to better manage the crash forces in low-speed impacts. Chrysler intends to inspect the involved vehicles and if necessary, install a trailer hitch where appropriate, free of charge (parts and labor). The parts required for this program are currently not available. Chrysler is making all reasonable efforts to obtain the parts as quickly as possible. Chrysler will contact dealers when the parts and repair procedure becomes available. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.
- 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 1012896905174039A$, 05072384A$, 05072138A$ - A/C Pressure Transducer For vehicles calling out AC Pressure Transducer Kit 05072138AA as a service part but built with different mating wiring connector (round) - also order connector repair kit 05019958AA (square).~ 2007MY RAM Trucks equipped with 6.7L Cummins turbo diesel engine only: If the A/C pressure transducer requires replacement, use part number 05072138AA that has a rectangular shaped electrical connector. If the engine wiring harness has a circular wiring connector, use jumper harness 68028774AA to change it to a rectangular connector.~ 6.7L RAM trucks built before10/17/2006 has pressures transducers (p/n 05191766AA) with a round connector that should have been changed per RRT 06- 068 to a rectangular transducer.~ 2001-2008 KJ, K1, ND.~
- 10121927NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
- 10057221Jeep grand cherokee 1993-1998, jeep liberty 2002-2007. Service bulletin regarding the vehicles with N45 or N46 trailer hitch assembly. The new trailer hitch assembly has been installed.
- 10030347Chrysler/jeep: flash: esp system may prematurely activate momentarily when negotiating a curve or mil illumination due to diagnostic trouble code p0340, p0344 or p0116. This involves selectively erasing and reprogramming the powertrain control module (pcm) with new software. Updated 5/24/10.
- 10024083Positive crankcase ventilation (pcv) system freezes in extreme cold ambient temperatures -- involves installing revised pcv system components.
- 10021684Generic powertrain control module (pcm) procedure.
- 10021599Passenger air bag deactivation.
Every Jeep Liberty model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.