2011 Jeep Liberty
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Jeep › Liberty › 2011
These records cover every 2011 Jeep Liberty. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2011 Jeep Liberty. Newest first.
Chrysler (FCA US LLC) is recalling certain 2012 Jeep Liberty and 2012-2013 Chrysler 200 and Dodge Avenger vehicles. A component within the occupant restraint controller (ORC) may fail and prevent the active headrests from deploying in the event of a rear-end crash.
Risk and remedy
Risk
If the active headrests do not deploy in certain rear-end crashes, the front seat occupants have an increased risk of injury.
Remedy
Chrysler will notify owners, and dealers will replace the ORC as necessary, free of charge. The recall began on December 4, 2017. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is T56.
Chrysler is recalling certain model year 2011-2013 Sebring and 200 vehicles manufactured June 28, 2011, through December 13, 2012; model year 2011-2013 Dodge Avenger vehicles manufactured June 25, 2011, through January 14, 2013; model year 2011-2012 Dodge Nitro vehicles manufactured June 17, 2011, through December 15, 2011; and model year 2011-2012 Jeep…
Risk and remedy
Risk
In the event of a crash necessitating the deployment of the active head restraints , their non-deployment could increase the risk of injury.
Remedy
Chrysler will notify owners, and dealers will flash the Totally Integrated Power Module (TIPM) or replace the occupant restraint control module, as needed, free of charge. The recall began on November 19, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N38.
Chrysler IS recalling certain model year 2011dodge journey, jeep wrangler, chrysler 200, chrysler 200 convertible, dodge avenger, dodge nitro, jeep liberty, dodge caliber, jeep compass, jeep patriot, dodge grand caravan and chrysler town & country vehicles. some of these vehicles may have been built with a missing or incorrectly installed steering column…
Risk and remedy
Risk
A missing or incorrectly installed rivet could compromise the ability of the steering column to support the occupant loads in the event of a frontal crash, decreasing the effectiveness of the frontal impact safety system. as a result, the condition may increase the potential for injury in a frontal crash.
Remedy
Dealers will inspect for rivet presence and alignment and repair the steering column pivot as required, free of charge. the safety recall began on july 4, 2011. owners may contact chrysler at 1-800-853-1403.
Owner complaints
181 complaints16 involved a crash2 involved a fire19 injuries
What owners report most
Latest complaints
- Air bags · Engine · Service brakes
I have owned this vehicle since 2011 and began having issues with passenger airbag light coming on intermittently or sometimes staying on during trip whether a passenger was in the seat or not. Had to install a new motor in 2025 due to antifreeze overflowing into engine components apparently after…
I have owned this vehicle since 2011 and began having issues with passenger airbag light coming on intermittently or sometimes staying on during trip whether a passenger was in the seat or not. Had to install a new motor in 2025 due to antifreeze overflowing into engine components apparently after overheating even though gauge on dash never indicated issue. squeeking sound when putting vehicle into reverse, cert mechanic installed front pads and rotors and rear brake pads and left rear brake caliper for a total cost of $620. Traveled to kc (appx 100 miles) one day later and vehicle began losing acceleration, stuttered and seeemed to surge intermitently then rear brake began locking up and smoking excessively before illuminating a check engine light. Draggin/locking rear brake broke loose on drive back home but still had check engine light. Took back to mechanic who diagnosed rapid misfire on cylinder no. 1 but was not able to trace cause. Recommended taking to dealership for diagnostic at a cost of $150 per hour. All 3 issues I am reporting are apparently pervasive with this vehicle as I have read numerous documented complaints from customers having the same or similar issues. However, nhtsa website indicates that there are no recalls associated with my vehicle. This IS unacceptable!!
- Power train
Always had Transmissions / power train problems with it until now my mechanic and his Transmissions specialist said that I need a new transmission. They and all other mechanics and people who owned these jeeps or known people who owned these jeeps said they have major Transmissions / power train problems that eventually require new Transmissions on short timings compared to all other vehicles.
- Structure › Body
Upon inspection, significant underbody rust
- Fuel/propulsion system
Everytime I get gas the full tank spits gas back at you which gets everywhere drips down the vehicle on to the ground. Very dangerous.
- Air bags
The airbag light came on and the computer indicated it's the clock spring. I know that this is a safety issue as I've had the same issue with a previous car in which it was recalled.
- Air bags › Frontal › Driver clockspring/spiral cassette
The contact owns a 2011 Jeep Liberty. The contact stated that while driving at unknown speeds, the horn was pressed; however, the horn failed to function as intended. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 169,000.
- Fuel/propulsion system
I currently own two of the same year vehicles. They BOTH have the same problem with the ECM. I have also spoken with multiple people who own Jeep vehicles @ the same year. We all seem to have; lifter, Rod knocks, oxygen sensors and ECM that have caused multiple other problems (and severe accidents)…
I currently own two of the same year vehicles. They BOTH have the same problem with the ECM. I have also spoken with multiple people who own Jeep vehicles @ the same year. We all seem to have; lifter, Rod knocks, oxygen sensors and ECM that have caused multiple other problems (and severe accidents) due to their malfunctioning. I have had both of my vehicles to licensed mechanics, who have advised me of the same problem. One of the 2011 Jeep Libertys have been owned by me since brand new, the other was bought used. PLEASE PLEASE help us out!!! I have spent so much money trying to repair these vehicles!!! THE ECM & OXYGEN SENSOR need to be recalled!!!
- Power train
The contact owns a 2011 Jeep Liberty. The contact stated while starting the vehicle, the contact heard a clicking sounding and the vehicle lunged forward. The check engine warning light was illuminated. The vehicle was taken an independent mechanic and the contact was informed that the vehicle…
The contact owns a 2011 Jeep Liberty. The contact stated while starting the vehicle, the contact heard a clicking sounding and the vehicle lunged forward. The check engine warning light was illuminated. The vehicle was taken an independent mechanic and the contact was informed that the vehicle needed to be diagnosed by a dealer. The contact was referred to the dealer. The dealer was contacted but no assistance was provided. The manufacturer was not contacted. The failure mileage was 73,000.
- Fuel system, gasoline
The contact owns a 2011 Jeep Liberty. The contact stated while adding fuel to the vehicle, there was no indication that the fuel tank was full, and fuel splashed outside of the vehicle. The local dealer was not contacted. The vehicle was not diagnosed nor repaired. The manufacturer was notified of the failure. The failure mileage was approximately 104,000.
- Air bags · Electrical system
Airbag light is on. Right front passenger door won’t lock or unlock automatically. Left front aux light inop. Not bulb related. Right front aux light goes off when right turn signal is activated.
- Unknown or other
The transmission doesn’t work properly. It has trouble getting into second gear, at times it doesn’t change to third gear or higher. On one occasion it briefly got stuck in overdrive
- Air bags · Electrical system · Steering
Airbag light on airbag making noise doors and windows unlock on its own steering wheel
- Electrical system
Faulty TIPM Several electronic issues including Electronic Throttle System. Vehicle doesn't respond due to faulty TIPM Sometimes starts very rough and stalls out
- Seats
The driver side active head restraint system headrest deployed while at a stop light. The was no collision. The driver was knocked forward by the headrest in the head/neck resulting in injury. No warning lights or issues alerted to a problem or malfunction. There is no recall on this make/model. Mileage 77,000
- Unknown or other
My 2011 Jeep Liberty sport on 06-27-21, was sitting in a Super market parking lot while shopping. I returned from shopping and noticed my - Rear back door glass was completely blown out,exploded. Was it a break-in situation ? Or what caused this ? I called the police to make a report. The…
My 2011 Jeep Liberty sport on 06-27-21, was sitting in a Super market parking lot while shopping. I returned from shopping and noticed my - Rear back door glass was completely blown out,exploded. Was it a break-in situation ? Or what caused this ? I called the police to make a report. The policeman said to contact insur. for replacement of blown out glass, and he filed his report. It is unknown my me,or policeman why this occurred. It, most definitely a Safety issue on 2011 Jeep Liberty Sport model
- Engine · Service brakes
Purchased vehicle used in january 2020. Five days later, the first dtc illuminated, and it has been an absolute nightmare ever since. So far I have replaced the purge valve, water pump, serpentine belt, radiator, alternator, pcv valve, tensioner assembly, front brakes, left exhaust manifold, door…
Purchased vehicle used in january 2020. Five days later, the first dtc illuminated, and it has been an absolute nightmare ever since. So far I have replaced the purge valve, water pump, serpentine belt, radiator, alternator, pcv valve, tensioner assembly, front brakes, left exhaust manifold, door seals, sway bar bushings/links - all within the first 10,000 miles. Brake caliper pistons seized and locked, causing brakes to smoke and overheat, discovered exhaust leak only after developing symptoms of carbon monoxide poisoning. Even after all of that, the vehicle still sounds awful and has serious performance issues. I fully expect that the engine will be toast any day, and I still have almost three years worth of payments left on it.
- Air bags · Electrical system · Unknown or other
My airbag light came on a few weeks ago and hasn't stopped going on and off it makes that annoying sound the whole trip every time I drive, the heat won't cut on it blows cold air I've had it looked at and repaired allegedly but it still won't blow hot air, the car keeps stalling and it has…
My airbag light came on a few weeks ago and hasn't stopped going on and off it makes that annoying sound the whole trip every time I drive, the heat won't cut on it blows cold air I've had it looked at and repaired allegedly but it still won't blow hot air, the car keeps stalling and it has completely shut off on me 3 times while I have been driving once on a busy freeway I was luckily by grace of god able to turn the wheel off to the side of the road before it locked I have a 2 year old daughter and I'm currently pregnant this IS insane and nobody can tell me what's wrong with it or how to fix any of these problems I got a loan for this car so now I'm stuck with this death trap, and now I'm seeing all these complaints about the same thing I'm baffled by the neglect and lack of concern or care for customers and there families who ride in their vehicles safety, I would think it would be a no brainer to recall the whole car if you can't fix the safety concerns or don't have a solution, I need a car to drive I'm wasting so much money on rentals because I have no options with this jeep I need a solution this IS crazy I rely on my vehicle for work as I do uber eats and grub hub I need help!!
- Service brakes
My vehicle was in motion and I was driving on a three lane street with a speed limit of 45 mph when the ABS brake system suddenly seized. The brakes remained engaged and the only way I could drive my car was to put it in reverse, then neutral then drive. My entire drive home I could hear the brakes and whenever I had to stop at a stop sign the brakes would lock.
- Structure › Body
Hi the main concern and problem with this car IS the sky slider! Millions of people are experiencing this issue all around. It failed me right away! After on incident when I was driving on highway the sky slider just came off!!! It almost caused multiply accidents! You can't even find the parts since jeep stop making knowing that the messed up !
- Air bags · Electrical system
The tipm in my jeep IS messing up and causing engine stalling, radio failure, etc. I have a blue driver that constantly gives me codes related to this part defect. I've also got an airbag light coming on all the time and yet my vin shows no recalls for this part. If I get into an accident my airbag…
The tipm in my jeep IS messing up and causing engine stalling, radio failure, etc. I have a blue driver that constantly gives me codes related to this part defect. I've also got an airbag light coming on all the time and yet my vin shows no recalls for this part. If I get into an accident my airbag might possible fail. My engine has almost stalled 3-4 times since I've owned it either from a stop light accelerating or crossing at an intersection this IS very dangerous.
- Structure › Body › Roof and pillars · Unknown or other
Jeep sky slider full open roof cannot close. the vehicle was stationary. this IS an electric roof with no option to manually close. *tr
- Unknown or other
I have a jeep liberty 2011 w/ a sky slider roof- where the entire roof IS fabric and slides back. it stopped working & wouldn't shut on tuesday and the only place that could put it into a garage and look at it before the rain- was the dealership. I heard back from them today- they no longer make…
I have a jeep liberty 2011 w/ a sky slider roof- where the entire roof IS fabric and slides back. it stopped working & wouldn't shut on tuesday and the only place that could put it into a garage and look at it before the rain- was the dealership. I heard back from them today- they no longer make the part that's broken. they were able to shut the roof, but I can never open it again b/c it won't shut and I'll have to pay them $243 again to close it. I'm reading online that this IS a common problem ' and even when the roof IS shut it- wind can get under it and blow completely off- potentially causing accidents if it were to rip completely off. I can't believe this hasn't been recalled. I know its common for places to stop making parts after 10 years, but there should be some resolution offered to shut your roof with reassurance it won't rip off and hurt someone. I'm pretty much scared to drive my jeep over 50 mph now and jeep basically just threw me back out in the world with no way to fix it because they have no way to fix it. this IS no way for a company to perform . I was a loyal jeep owner since 1997! here are some pics of other peoples roofs flying off. *tr
- Air bags
The air bag dash light has recently come on, after the mechanic tried unsuccessfully to reset it the same error message pops up. when the computer IS connected it shows the only airbag affected IS the one in the steering wheel. this vehicle has never been in a crash, much less anything to cause the airbag to deploy so it IS the original. it stays on consistently anytime the key IS in the on/started position
- Electrical system · Unknown or other
The doors do lock through the electrical system. You can manually lock and unlock the vehicle but can not lock/unlock through the electrical system. Cd player also does not work. I believe the issue may be stemming from the fuse box under the hood, I have checked all the fuses and everything shows to be good.
- Air bags
Passenger airbag light stays on on the dash
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Active Head Rest Inadvertent Deployment
The Office of Defects Investigation (ODI) opened PE19014 on September 9, 2019, to investigate 128 consumer complaints alleging that the Active Head Rest (AHR) inadvertently deployed without the occurrence of a crash or other rear impact event in model year (MY) 2014 Jeep Grand Cherokee and Dodge Durango vehicles.When…
The Office of Defects Investigation (ODI) opened PE19014 on September 9, 2019, to investigate 128 consumer complaints alleging that the Active Head Rest (AHR) inadvertently deployed without the occurrence of a crash or other rear impact event in model year (MY) 2014 Jeep Grand Cherokee and Dodge Durango vehicles.When ODI opened the investigation, ODI was aware of thirteen alleged injuries.A small number of Early Warning Reports identified driver and/or passenger front seat AHR inadvertent deployments without a rear impact event.Reported safety consequences resulting from the AHR deployments include concussions, headaches, soft tissue injuries, disorientation, nausea, vomiting and/or loss of vehicle control as a result of being surprised and distracted by being struck in the head by the inadvertent AHR deployment. On September 24, 2019, ODI sent an Information Request (IR) letter to Fiat Chrysler Automobiles (FCA).ODI requested certain detailed information from FCA related to the following subject vehicles: MY 2010-2014 Dodge Avenger 200, MY 2010-2014 Dodge Calber, MY 2010-2014 Chrysler Sebring, MY 2013-2015 Ram Tradesman, MY 2012 Ram Van, MY 2010-2019 Dodge Grand Caravan, MY 2010-2016 Chrysler Town and Country, MY 2010-2017 Jeep Compass, MY 2011-2020 Dodge Durango, MY 2011-2020 Jeep Grand Cherokee, MY 2010-2019 Dodge Journey, MY 2010-2012 Jeep Liberty, MY 2010-2011 Jeep Nitro, and MY 2010-2011 Jeep Patriot vehicles.On December 2, 2019, ODI received a response from FCA that included vehicle production data, consumer complaints, field reports, warranty claims, manufacturer actions, production changes, and other data related to the alleged defect from the start of production (2010) through September 24, 2019.On January 27, 2020, ODI received an update to the December 2, 2019, IR response from FCA.On September 22, 2020, ODI requested additional subject vehicle AHR information from FCA.ODI received FCA's response on October 21, 2020.ODI subsequently received an update to FCA's October 21, 2020, response on February 16, 2021.During the investigation, ODI requested updates to certain IR questions on two occasions.FCA provided updates to question #2 on March 5, 2021, and questions #2 and #5 on May 26, 2023. FCA’s IR response data identified approximately 7.5 million subject vehicles (with approximately 15 million AHR assemblies).Due to the large number of vehicles and failure reports, ODI focused its analysis on the FCA vehicle model with the highest failure rate to represent the worst-case scenario.For this purpose, ODI focused on MY 2012-2015 Jeep Grand Cherokee vehicles for its analysis.This population includes 710,890 vehicles that FCA manufactured between August 19, 2011, and August 8, 2015.ODI identified 2,839 alleged AHR failures within this limited population.ODI identified 263 alleged injuries that were caused by AHR failures in MY 2012-2015 Grand Cherokees vehicles.Of these alleged injuries, ODI categorized them as eighty-two (82) soft tissue (neck/whiplash, bruise) injuries, four (4) concussions, fifty-nine (59) headaches, and one hundred eighteen (118) without a specific injury description.Although complainants have alleged injuries, ODI has been unable to obtain evidence to substantiate or validate any injuries where medical treatment was required.Consumer outreach was conducted by ODI, where sixty-three (63) FCA complainants with alleged injuries were contacted.Twelve of the sixty-three FCA consumers responded and were interviewed by ODI.ODI requested medical records, however, only one response was provided. Attorneys representing the responding complainant provided a synopsis that indicated they had experienced prior neck-related injuries dating to the mid-1990s.ODI also contacted one hundred (100) consumers who submitted Vehicle Owner Questionnaires (VOQ) in an attempt to validate alleged injuries. Despite the efforts of ODI, the office has been unsuccessful at obtaining substantive documentation/evidence supporting complaints that allege serious injuries (where pre-existing medical conditions did not already exist). In addition to the low severity of alleged injuries caused by AHR deployments, there have been eleven alleged crashes and two alleged lane departures within the entire subject vehicle population that has been in the field up to sixteen years (with over 8,500 AHR inadvertent deployments).ODI was not able to validate that the alleged crashes were the result of inadvertent head rest deployments, and the crashes were minor in nature. ODI has conducted a thorough investigation of the alleged safety defect and with up to sixteen years of exposure for some vehicles and over 8,500 inadvertent AHR deployments, no serious crashes or injuries could be validated in the sub-population of focus.The lack of serious injuries validated by ODI with such large period of field exposure is consistent with thework done by NHTSA’s Human Injury Research Division and the Biodynamic Research Corporation, which support that an inadvertent AHR deployment is not likely to cause serious injury.In addition to the low risk of injury, FCA released an extended warranty program that covers inadvertent AHR deployment for ten years / unlimited mileage from the vehicle's in-service date. PE19014 is closed with the FCA extended warranty program.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist, and the Agency reserves the right to take additional action if warranted by new circumstances. To review a complete closing summary, please the attached closing report. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Electrical overstress
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air…
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
- Totally Integrated Power Module Failure
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007…
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10242717Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
- 10229871Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
- 10229825RHW RHP Radio Software Enhancements
- 10229572Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10228020Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
- 10227983If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
- 10225424Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10225287Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10224083Active Head Restraint (AHR) Inadvertent Deployment - X85 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
- 10224058Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2010-2013 Jeep Liberty (KK) and 2010-2012 Dodge Nitro (KA)
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221831(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10221554Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following DTCs set in the PCM memory: **U0140 - Lost Communication With Body Control Module (BCM) (10-12 MY only). Auto Shutdown (ASD) Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (10-12 MY only).** P0401 - EGR System Performance. In addition the customer may notice one of the following conditions: Hard to start, long crank time or even a no start. The customer may describe that If the gas pedal is pushed slightly the vehicle starts as expected (11 MY KA only).
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220993RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220098Authentic Mopar Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar Glass.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10218783Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
- 10218303RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
- 10218037Hands Free Module Prompts Begin Erroneously.
- 10217942Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
- 10217714Clock In The Radio Loses Time This bulletin involves replacing the Wireless Control Module (WCM)/Sentry Key Remote Entry Module (SKREEM). Customer may experience a condition where the clock will lose over one minute a month.
- 10217569Failure Code Change This bulletin involves notifying the dealers and technicians of a change to the Required Flash (RF) and Customer Concern (CC) failure codes.
- 10217521Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
- 10216407Left And/Or Right Door High Closing Effort This bulletin involves inspecting front door body mounted seal placement and if necessary, adjusting seals and/or left and/or right front door striker to eliminate high closing effort. The customer may experience high closing efforts on the left and/or right front doors when closing.
- 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10216394Waterleak At The Rear Of The Headliner This bulletin involves inspecting the rear of the headliner for water residual and if necessary sealing the right and/or left roof ditch. The customer may notice the headliner is wet in either the right or left rear corners.
- 10216338Flash: RHR, RHW Or RHP Radio Software Enhancements This bulletin involves upgrading the software on the RHR, RHW or RHP Radio. The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.
- 10215969Clock In The Radio Loses Time This bulletin involves replacing the Wireless Control Module (WCM)/Sentry Key Remote Entry Module (SKREEM). Customer may experience a condition where the clock will lose over one minute a month.
- 10215071Hands Free Module Prompts Begin Erroneously.
- 10189374Clock In The Radio Loses Time This bulletin involves replacing the Wireless Control Module (WCM)/Sentry Key Remote Entry Module (SKREEM). Customer may experience a condition where the clock will lose over one minute a month.
- 10188664Clock In The Radio Loses Time This bulletin involves replacing the Wireless Control Module (WCM)/Sentry Key Remote Entry Module (SKREEM). Customer may experience a condition where the clock will lose over one minute a month.
- 10187680Active Head Restraint (AHR) Inadvertent Deployment - X92 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
- 10187668Warranty Bulletin D-20-22 (X92) Active Head Restraint - Select 2011 Dodge Journey (JC), Dodge Avenger/Chrysler 200 (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan/Chrysler Town & Country (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK) (Rev. A)
- 10187659Warranty Bulletin D-20-22 (X92) Active Head Restraint - Select 2011 Dodge Journey (JC), Dodge Avenger/Chrysler 200 (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK)
- 10184761Active Head Restraint (AHR) Inadvertent Deployment - X85 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
Every Jeep Liberty model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.