2008 Jeep Liberty
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Jeep › Liberty › 2008
These records cover every 2008 Jeep Liberty. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2008 Jeep Liberty. Newest first.
Chrysler Group LLC (Chrysler) is recalling certain model year 2007-2008 Dodge Nitro 4X2 vehicles manufactured March 21, 2006, through March 1, 2008; and 2008 Jeep Liberty 4X2 vehicles manufactured February 15, 2007, through March 1, 2008. The transfer case heat shield may drop down and rub on the drive shaft, weakening it and potentially causing the drive…
Risk and remedy
Risk
If the drive shaft breaks, a section of it can strike the transfer case tunnel with enough force that the airbag computer will believe the vehicle is in a crash and thus deploy the airbags. Additionally, the drive shaft failure will result in a loss of motive power. Either condition may increase the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will add a bracket to support the rear of the heat shield, free of charge. An interim letter was mailed to owners on May 29, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N10.
Chrysler IS recalling certain model year 2008 jeep liberty vehicles. the vehicles are equipped with windshield wiper motors that contain excess adhesive that may allow for water intrusion, which could result in intermittent and eventually inoperative windshield wiper operation.
Risk and remedy
Risk
A failing or inoperative windshield wiper system will reduce a driver's visibility which could result in a crash.
Remedy
Dealers will replace the windshield wiper motor free of charge. the safety recall began on december 1, 2010. owners may contact chrysler at 1-800-853-1403.
Rock krawler IS recalling 44 performance suspension systems sold as aftermarket equipment for use on the vehicle listed above. these suspension systems were produced with grade 2 carriage bolts instead of the proper grade 5 carriage bolts. the improper grade 2 carriage bolts could experience a loss of clamping force for the bottom strut fork.
Risk and remedy
Risk
This condition could cause a loss of effective lift and lowering of the affected vehicle, possibly creating the driver to panic which could possibly lead to a vehicle crash.
Remedy
Rock krawler will notify owners and provide a free remedy. the safety recall began on october 15. 2008. all the affected untits have been remedied. owners may contact rock krawler at 1-518-270-9822.
Chrysler IS recalling 3,663 my 2007-2008 dodge nitro and my 2008 jeep liberty vehicles equipped with manual transmissions. the park brake lever clutch drum may distort and reduce the effectiveness of the park brake system.
Risk and remedy
Risk
This could allow the vehicle to move inadvertently and cause a crash without warning.
Remedy
Dealers will replace the park brake lever assembly free of charge. the recall began on october 27, 2008. owners may contact chrysler at 1-800-853-1403.
Chrysler IS recalling 494 my 2008 jeep liberty vehicles. the windshield and/or fixed rear quarter glass may have been assembled using incorrect urethane adhesive. this could affect glass retention.
Risk and remedy
Risk
If the glass separates while driving, it could strike another vehicle or injure a pedestrian.
Remedy
Dealers will replace the windshield and/or fixed rear quarter glass free of charge. the recall began on october 13, 2008. owners may contact chrysler at 1-800-853-1403.
Owner complaints
541 complaints11 involved a crash4 involved a fire19 injuries
What owners report most
Latest complaints
- Electrical system · Unknown or other
Twice it’s happened my turned. I went to turn my my key to power to open the doors and the heater went off. The horn started blaring. The windshield wipers came on. They was squirting out windshield fluid and I wasn’t even in the car yet I couldn’t get it to shut off so I got under. I took a fuse…
Twice it’s happened my turned. I went to turn my my key to power to open the doors and the heater went off. The horn started blaring. The windshield wipers came on. They was squirting out windshield fluid and I wasn’t even in the car yet I couldn’t get it to shut off so I got under. I took a fuse out. It turned off and now my car doesn’t run. The first address is my home address at [XXX], and the second one was at the [XXX]. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Air bags
Airbag light has been coming on and stays on. When I start my vehicle the airbag in the dash on passenger side sounds like it’s trying to escape. Scary. I have a service appointment for April 2, 2026, Thursday. They can’t get me in sooner. I understand the recall doesn’t apply. I’m stating that it SHOULD! Please expand your recall to more Jeep models. I want this on record as I am deeply concerned about my safety.
- Suspension
Suspension rotting out for jeeps were recalled up until 2007. My 2008 jeep has the same issue with rotted suspension bars. Originally recalls were for 2005 they added up to 2007. Mine is a 2008. We need to add another year suspension bar is rusted in half. 158 thousand miles. the rest of underbody is solid. .
- Unknown or other
I am having problems when I back up and turn the steering wheel it starts to make noise and it slows down line it don't want to turn. And my EPS light will not turn off no matter what I do to it. There is something seriously wrong when I'm backing up n turning the wheels if you could please help me…
I am having problems when I back up and turn the steering wheel it starts to make noise and it slows down line it don't want to turn. And my EPS light will not turn off no matter what I do to it. There is something seriously wrong when I'm backing up n turning the wheels if you could please help me an if it has nothing to do with the recall but I'm sure it dies let me know what it is. Thank You [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Suspension
Both lower rear control arms rusted out, broke off entirely while driving. Under 100k miles. This issue was recalled on the same make and model up until 2007 but they clearly haven't fixed the issue.
- Air bags
Steering wheel air bag went off on its own. Started the car and pop. Door locks won’t work on drivers door when unlocking with key fob
- Air bags
The contact's husband owned a 2008 Jeep Liberty. The contact stated that while driving at various speeds, the air bag and traction control warning lights would flash on the instrument panel. The contact stated that while driving at 40 MPH, the vehicle hydroplaned while crossing a puddle of water…
The contact's husband owned a 2008 Jeep Liberty. The contact stated that while driving at various speeds, the air bag and traction control warning lights would flash on the instrument panel. The contact stated that while driving at 40 MPH, the vehicle hydroplaned while crossing a puddle of water and landed in a ditch. The side curtain air bags deployed; however, the driver and passenger air bags did not deploy. The contact stated that an abnormal odor was emitted from the vehicle. The contact sustained bruising on the left arm but did not seek medical attention. A police report was not filed. Due to the failure, the vehicle was initially towed to the contact's home and was later towed to an independent tow yard. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to file a complaint. The vehicle was destroyed. The failure mileage was unknown.
- Suspension
Rear control arms rusted on both sides. One side cracked almost completely through. Mechanic confirmed close to failure which would cause loss of control of vehicle. In 2017 this model was recalled for this danger but only through model year 2007. Appears same defective part was used in this model year (2008). No warning lights of problem. Observed myself and mechanic confirmed problem.
- Structure › Body
Recently driving down the road heard a very loud noice thought i had a tire blowout. It was both Rear lower control arms broken Completely into( very rusty ).It also broke my exhaust and banged up the driveshaft. This is very expensive to repair and could have very well been Deadly. Would like for someone to contact me asap ty
- Air bags
The air bag light has been turning on for no reason I don’t know what’s causing it
- Electrical system · Engine · Visibility/wiper
While driving the vehicle the car started having various electrical problems. The wipers kept going on and off and all instrument lights kept going on and off.
- Tires
I was driving from NY City to Boston, MA when suddenly I hear a big noise thankful to God I didn't lose control on my vehicle, I parked and notice the driver's side tire was completely deflated. I wait for several hours for help. Also one of the rear tires has big bulge on it. I check for any…
I was driving from NY City to Boston, MA when suddenly I hear a big noise thankful to God I didn't lose control on my vehicle, I parked and notice the driver's side tire was completely deflated. I wait for several hours for help. Also one of the rear tires has big bulge on it. I check for any recalls on these tires, but there is none for this size. What can I do? The tires have only 2000-3000 miles on the car. I call Cooper customer service recalls and they were rude and did't help at all. This is a safety issue and I would like my tires to be replaced ASAP. Thank yo
- Air bags
Airbag system failure due to clockspring malfunction. Identified by owner due to airbag system failuer warning light and repaired by Billion Chrysler, Jeep, Ram in Sioux Falls, SD.
- Electrical system › Horn · Visibility/wiper
The contact owns a 2008 Jeep Liberty. The contact stated while at a standstill, the horn and windshield wipers would activate independently. The vehicle was not taken to a local dealer. The manufacturer was informed of the failure and told the contact to call NHTSA to file a complaint. The failure…
The contact owns a 2008 Jeep Liberty. The contact stated while at a standstill, the horn and windshield wipers would activate independently. The vehicle was not taken to a local dealer. The manufacturer was informed of the failure and told the contact to call NHTSA to file a complaint. The failure mileage was unavailable. THE CONSUMER STATED THE VEHICLE'S BATTERY WAS DISCONNECTED IN ORDER TO PREVENT THE FAILURE FROM RECURRING.
- Air bags
Airbag was replaced Sept 2019. I just had to replace coil spring again in the airbag Very costly
- Suspension › Front › Control arm › Lower arm
The contact owns a 2008 Jeep Liberty. The contact stated that while replacing the brake pads, the contact became aware that the driver’s side lower control arm and rear axle were corroded. The manufacturer was made aware of the issue and informed the contact that the VIN was not included in NHTSA campaign number: 18V278000 (Suspension). The vehicle was not repaired. The failure mileage was 74,762.
- Engine · Fuel/propulsion system · Power train
We had a fire in the engine compartment. Fire started at the engine manifold ! We took pictures of the damage! This could have killed my son in law ! We gifted the vehicle to him so it could be used as a station vehicle. A dangerous situation Exist ! There is no recall or acknowledgment of this problem being identified!
- Fuel/propulsion system
Gas burps out every time you fill the tank!
- Engine · Service brakes · Suspension
Once parked the heat sheild came up against the heater core and must have sparked causing it to catch fire under the hood! Needs to be investigated before causing a possible fatal issue
- Fuel/propulsion system
When filling fuel tank to full capacity and fuel flow IS shut off, fuel comes back up out of fill port spilling at least 2 cups of gas over filler and ground. Happens every time tank IS filled full. This occurs while vehicle IS stationary engine off while at any gas station. It IS an apparent…
When filling fuel tank to full capacity and fuel flow IS shut off, fuel comes back up out of fill port spilling at least 2 cups of gas over filler and ground. Happens every time tank IS filled full. This occurs while vehicle IS stationary engine off while at any gas station. It IS an apparent failure on a valve in the gas tank requiring entire tank to be replaced at the owners expense. IS a known issue to manufacturer.
- Back over prevention › Warnings · Power train · Unknown or other
On 17 february, with my foot on the brake, I placed my car into reverse to back into an available parking spot and the engine revved up on its own and shot the car backward at top speed hitting and toppling a san diego light post and stopping when it hit a tree. No one was injured thank goodness. I found on line that this had happened at least 31 times with a similar jeep liberty.
- Electrical system · Engine · Unknown or other
The vehicle starts good no problems during the fist start of the engine on the day, my work IS a follows I make several stops during the day with an approximated 30 min in between, later during the day vehicle stalls, several lights on dash board flush and move, I have to make serval attempts to…
The vehicle starts good no problems during the fist start of the engine on the day, my work IS a follows I make several stops during the day with an approximated 30 min in between, later during the day vehicle stalls, several lights on dash board flush and move, I have to make serval attempts to start the engine vehicle continue to stalls, at this pints the vehicle has staid several occasions at the dealer and different mechanic per the dealer they dint now why the vehicle IS doing this , per mechanic starter, and alternator good. So far I had replace the battery, computer and pay for multiple inspections, this IS frustrating, I also noticed online re search multiple jeep owners have the same complaint, any assistance IS greatly appreciated. Thank you .
- Structure › Body
The vehicle was in motion going about 40 miles per hour when the sky slider roof almost came off. It started flapping very bad. I had it fixed and it IS broken again.
- Service brakes · Unknown or other · Vehicle speed control
I'm speeding up as I'm passing a truck on 395, signaling with left blinker. Start speed as beginning to pass IS approx. 55 mph. I signal right as I pull back in the south bound lane, take my foot off the gas pedal as I notice I'm driving 80 mph. The gas pedal IS stuck and the car IS going 80 mph on…
I'm speeding up as I'm passing a truck on 395, signaling with left blinker. Start speed as beginning to pass IS approx. 55 mph. I signal right as I pull back in the south bound lane, take my foot off the gas pedal as I notice I'm driving 80 mph. The gas pedal IS stuck and the car IS going 80 mph on its own. I step on the brake carefully but its rock hard and doesn't move at all. At this point the car IS stuck at 80 mph. I try to brake again but the same - brake pedal IS stuck, doesn't move at all and IS rock hard. Road conditions are good so I'm in a "controlled panic", and try the brake one more time. This time the brakes engage and I get the car down to 65 mph. I don't want to burn the brakes so I release the brake and immediately the car speeds up on its own to 80 mph. I repeat. Slow to 65 mph, step off the brake and again the car immediately speeds up to 80 mph. At this point my thoughts go to cruise control (which I had not activated or used on this trip). I pull the "cancel" on the cruise control, nothing. I try again and look at the dashboard where the cruise control light IS "off", indicating cruise control IS not on. I turn the cruise control on and pull the "cancel" again and brake. This time the car comes out of it, and I turn the cruise control off again. Since the cruise control was not even on to begin with, I don't know if that's what actually made the car 'unfreeze'. I was lucky I was on a straight stretch of road with no traffic in front of me. Since I was passing a truck I'm not 100% sure if I sped up to 80 mph or if the car suddenly did that on its own. I do believe the car did that, as there was no reason to get up to that speed to pass safely.
- Service brakes · Unknown or other
There IS a grinding noice coming from either the transfer case or the dove shaft, either was it IS loud and causes lights on the dash to come on and stay illuminated the lights are as follows: ABS, traction control, esp bas, and service 4WD.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Totally Integrated Power Module Failure
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007…
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221831(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220471Mechanical rocker arm, intake, 1.7 ratio.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10218307Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10216269Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
- 10215825Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.
- 10191460Valve Body. These may cause over drive cycling.
- 10191442Mechanical rocker arm, intake, 1.7 ratio.
- 10188658Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break.
- 10180221(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10166537RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
- 10140258Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10140065Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10139985Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 10139978Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 10138987Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10136479Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
- 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10128983Fuel Spit Back During Refueling Due To Inlet Check Valve (X46 Lifetime Warranty Extension) This bulletin involves replacing the fuel tank with a revised part. Some customers may experience a fuel spit back condition during a refueling event.
- 10128948Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10121927NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
- 10076509SUBJECT: Flash: UConnect and Voice Recognition Inoperative SYMPTOM/CONDITION: The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10052148Jeep: on some jeeps, when refueling, the fuel will spit back due to inlet heck valve and information IS provided regarding replacing fuel tank with new part. Models 2008 liberty, 2007-2008 nitro.
- 10034229Jeep: manual transmission pops out of gear. The transmission pops out of first gear while accelerating. The condition, may occur intermittently and may be difficult to diagnose. Verify that the shift boot IS not causing the issue by ensuring the boot IS not binding when in first gear.
- 10030707Jeep: in cold climates a mil illumination p0123 or p0222 or stored diagnostic trouble code p0123 or 00222 and the etc light illuminated. This involves replacing the electronic throttle body and clean air duct.
- 10026168Chrysler/dodge/jeep: flash:diagnostic trouble code, dtc p0740 or p1798 and automatic transmission shift improvements 1-2 or 2-3 cold shift improvements.
Every Jeep Liberty model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.