2006 BMW Z4
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2006 BMW Z4. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2006 BMW Z4. Newest first.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3…
Risk and remedy
Risk
An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.
Remedy
This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2006 525i, 525xi, 530i, 530xi, 530xi Sports Wagon, 325i, 325xi, 325xi Sports Wagon, 330i, 330xi, Z4 3.0i and Z4 3.0si vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Risk and remedy
Risk
An electrical short can cause the parts within the PCV valve to melt, increasing the risk of a fire, even when the vehicle is not in use.
Remedy
BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. The recall began May 30, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion to recall 17V-683.
Owner complaints
91 complaints1 involved a crash3 involved a fire1 injuries1 deaths
What owners report most
Latest complaints
- Steering
The electronic steering has failed several times while driving. This makes it very difficult to maintain a lane and avoid other vehicles. This problem continues intermittently. Thousands of Z4 owners have reported the same issue in online forums.
- Steering
In hot weather, the steering binds, making keeping the car in the correct lane extremely difficult. The car will dart from one side to the other. The car will be nearly impossible to keep in the correct lane.
- Electrical system · Exterior lighting
I have just found out that my 2006 BMW Z4 Convertible has serious wiring issues. The wires for example on my front headlights the insulation is falling off the and leaving bare wires. I am very concerned this could be a fire safety issue that could result in bare electrical wires shorting…
I have just found out that my 2006 BMW Z4 Convertible has serious wiring issues. The wires for example on my front headlights the insulation is falling off the and leaving bare wires. I am very concerned this could be a fire safety issue that could result in bare electrical wires shorting together and starting a car fire. My research shows that many people who have 2006 BMW Z4 Convertibles are having this same issue. This seems to be a real issue with BMW using cheap wiring harnesses material and over time due heat and cooling is cause the insulation to fail and resulting in this issue.
- Steering
When the car gets hot (parked in the sun) the steering becomes knotchy or sticky and the car becomes difficult to control. No problems whatsoever when the car is cool or on a cooler day. This problem has been witnessed by a BMW technician and there are no warning lights. This appears to be a fairly common issues with these cars.
- Engine and engine cooling
The contact owns a 2006 BMW Z4. The contact received notification of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair.…
The contact owns a 2006 BMW Z4. The contact received notification of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to an independent mechanic who diagnosed that the PCV valve heater needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 50,000. VIN tool confirms parts not available.
- Engine and engine cooling
The contact owns a 2006 BMW Z4. The contact received a notification for NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was unavailable. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer…
The contact owns a 2006 BMW Z4. The contact received a notification for NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was unavailable. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer had been notified of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. VIN tool confirms parts not available.
- Engine
The contact owns a 2006 BMW Z4. The contact stated that while operating the vehicle, the check engine warning light illuminated and the vehicle lost motive power and stalled. Additionally, there was a burning odor on the inside and outside of the vehicle. The vehicle was taken to an independent…
The contact owns a 2006 BMW Z4. The contact stated that while operating the vehicle, the check engine warning light illuminated and the vehicle lost motive power and stalled. Additionally, there was a burning odor on the inside and outside of the vehicle. The vehicle was taken to an independent mechanic who changed the engine spark plugs however, the failure persisted. The local dealer and manufacturer were not notified of the failure. The failure mileage was 120,000.
- Engine and engine cooling
The contact owns a 2006 BMW Z4. The contact stated that while at a complete stop at the traffic light, the vehicle overheated and stalled. The coolant temperature warning light illuminated. The contact waited for the vehicle to cool down and then restarted the vehicle and continued driving. The…
The contact owns a 2006 BMW Z4. The contact stated that while at a complete stop at the traffic light, the vehicle overheated and stalled. The coolant temperature warning light illuminated. The contact waited for the vehicle to cool down and then restarted the vehicle and continued driving. The contact stated that the failure reoccurred several times. The vehicle was towed to the dealer several times. The dealer completed the engine lifters replacement and other unknown repairs however, the failure persisted. The contact stated while stopped at the traffic light, the vehicle began to overheat significantly and stalled. There was no warning light illuminated. The contact noticed smoke coming from underneath the hood of the vehicle. The contact immediately exited the vehicle. The contact later pushed the vehicle to the side of the road with assistance. The vehicle was towed to an independent mechanic where it was diagnosed that the engine needed to be replaced. The contact later received notification of NHTSA Campaign Number: 19V273000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 52,000. VIN tool confirms parts not available.
- Steering
The Steering wheel gets Hard, looks like power steering gets disabled automatically while driving, making it almost impossible to steer. This has started to happen after hot weather had started few months back. I have tried to reproduce this issue several times, but it happens randomly and Not all…
The Steering wheel gets Hard, looks like power steering gets disabled automatically while driving, making it almost impossible to steer. This has started to happen after hot weather had started few months back. I have tried to reproduce this issue several times, but it happens randomly and Not all the time. I don't drive the car much. But this is definitely a serious issue, I checked the BMW community and a lot of people are facing this issue. Not Sure how many have filed a complaint here. But this definitely should be addressed by BMW as this is not just one person facing this issue, there are hundreds and thousands of them. Level of severity is high, as someone who might have not faced this issue yet might suddenly face it on the highway could result in an extremely fatal accident. Havent reported to BMW yet, But found this issue is being faced by alot of people I thought to file my complaint here. I will soon get it repaired or replaced. There were no Warning lamps or messages prior to this. It started happening in September 2021.
- Steering
When the outside temperatures are warmer (mid 80's and above) the steering wheel will stick in the center position and require it to be jerked a bit to keep control. This occurs at all speeds, but does not seem to be the case when stopped. since it requires the steering wheel to be jerked to…
When the outside temperatures are warmer (mid 80's and above) the steering wheel will stick in the center position and require it to be jerked a bit to keep control. This occurs at all speeds, but does not seem to be the case when stopped. since it requires the steering wheel to be jerked to correct, it can cause the car to swerve. I have had the car for several years began noticing the issue once the weather got warmer. The date entered below is today's date, but I have had the issue for perhaps 5 years.
- Steering
During warm weather the steering will momentary stick while driving which requires additional force to overcome. This happens at all speeds but is more noticeable at highway speeds while trying to maintain vehicle in driving lane. There are numerous complaints of this on the NHTSA site. I have…
During warm weather the steering will momentary stick while driving which requires additional force to overcome. This happens at all speeds but is more noticeable at highway speeds while trying to maintain vehicle in driving lane. There are numerous complaints of this on the NHTSA site. I have written to BMW North America about this safety problem and mentioned the multitude of similar complaints but they refuse to address the problem and suggest I purchase a new steering column at $2500+!
- Structure › Body
The convertible top on the 2006 Z4 BMW has a mechanism that raises and lowers that fails. It's location IS such that it IS exposed to the elements. When I bought my car (used)i went to a BMW mechanic that told me that if I did have him fix it it would happen again. Talking to other BMW mechanics I got the same info.
- Steering
Vehicle steering becomes "sticky" after vehicle has been exposed to warm temperatures. This causes the steering to center and require greater than usual force to off center the wheel, causing the car to be difficult to control especially at highway speeds.
- Electrical system
Went to change my headlight bulb and notices all of the wires were bare. The sheathing around the wires have all corroded. This IS for the complete headlight assembly. Every single wire has corroded. Seems like a fire hazard.
- Air bags
About 9 years (2015) after purchasing vehicle the airbag warning light began illuminating constantly. The vehicle was purchased new and had approximately 55K miles when issue began. Vehicle has never been in a minor or major accident. Vehicle was taken to an independent mechanic, but diagnosis…
About 9 years (2015) after purchasing vehicle the airbag warning light began illuminating constantly. The vehicle was purchased new and had approximately 55K miles when issue began. Vehicle has never been in a minor or major accident. Vehicle was taken to an independent mechanic, but diagnosis could not be determined. Contacted BMW about issue, but was told my vehicle was not covered under any of the airbag recalls they've initiated. No action was taken by me to determine root cause and continued to utilize vehicle with air bag light always illuminated. In february 2018, received a letter from BMW regarding warranty extension to 15 years for front passenger seat occupancy mat (OC3) for air bag system. Believing airbag issue was due to OC3 mat, brought my vehicle to local BMW dealer to get repair. BMW diagnosed the issue as a "restraint pass lower belt unit faulting" and not OC3 mat. Had repair performed successfully.
- Electrical system · Exterior lighting
The insulated wiring inside the headlight housing has hardened and the insulation had cracked and fallen off. this allows the wires to short and causes unexpected failure of the headlights, parking lights, turn signals and other items inside the headlight housing. The lights failed unexpectedly and intermittently.
- Steering
Very sticky steering, dangerous in hot weather, this happens at all speeds. It sometimes requires significant effort to correct it. This IS a serious safety issue.
- Electrical system · Engine · Fuel/propulsion system
My battery IS in good condition but I can't start the engine.-700km oil service warning light display on my dash.fuel pump IS working.them open the key like that sound gap gap IS come out...pls help me...
- Steering
Steering appears to be sticking or staying at a certain point in the steering radius. I almost veered into oncoming interstate traffic. I compensated immediately, but it released its "stick" and turn to much and almost veered into traffic I was in. Very scary, very dangerous. There was a possibility of much injury or death because of this issue. Bad
- Steering
Recurring problem with steering input effort when driving on highways. The steering sticks when in the center position. Resistance IS felt and IS difficult to return back to the center position. Sticking problem seems worse at higher speeds and with warm outside temperature above 80 degrees. the…
Recurring problem with steering input effort when driving on highways. The steering sticks when in the center position. Resistance IS felt and IS difficult to return back to the center position. Sticking problem seems worse at higher speeds and with warm outside temperature above 80 degrees. the faster the speed, the more effort needed to overcome the detent resistance, to the point that it becomes easy to oversteer the car. This can be real scary during avoidance maneuvers and quick lane changes.
- Unknown or other
The convertible top failed 2011/30229 miles, still under cpo warranty. The dealership only topped off the hydraulic fluid and claimed no leak found. it failed again 2014/45809 miles. This time seals were replaced and hydraulic lines. Goodwill repair with 50% out of pocket. it failed again earlier…
The convertible top failed 2011/30229 miles, still under cpo warranty. The dealership only topped off the hydraulic fluid and claimed no leak found. it failed again 2014/45809 miles. This time seals were replaced and hydraulic lines. Goodwill repair with 50% out of pocket. it failed again earlier this year 2018/62112 miles. This time I was quoted $2,938 to $3,658. I had it diagnosed in may and was waiting for an answer of the service manager about BMW assisting with the repair and had not heard back. I inquired again two days ago and got a reply that BMW would not pick up any of the repair cost. it appears that it was a slowly developing defect. Where would have the fluid have gone at the first repair? also doing some research turned up a lot of the same trouble for other owners. Apparently it IS a design flaw. Water not draining because of clogging and consequently causing damage to the hydraulic system.
- Unknown or other
The vehicle was parked in a garage and set on fire, resulting in a house being burned down and the fatality of my father. The fire marshal's report was inconclusive as to how the fire started.
- Steering
Steering IS extremely notchy and unpredictable, especially on hot days. when in motion, the steering wheel requires force to turn, and sometimes will turn slightly without driver input. it appears that the power assist steering IS actuating when it should not be, causing either resistance to…
Steering IS extremely notchy and unpredictable, especially on hot days. when in motion, the steering wheel requires force to turn, and sometimes will turn slightly without driver input. it appears that the power assist steering IS actuating when it should not be, causing either resistance to steering inputs, or applying force when no steering input has been applied. when the engine IS not running, or at very slow speeds, noise can be heard from the power assist motor. it actuates when no steering inputs are being applied. when steering inputs are applied, too much resistance can be felt and the motor makes additional noises. I purchased the car in february of 2016, and this has been happening since approximately spring of 2016. it has been getting progressively worse.
- Steering
During weather above 80 degrees, the steering becomes "twitchy" or "notchy," no longer smooth, but requiring additional effort to turn the steering wheel, at which point, the tires move more than needed, requiring a steering adjustment the opposite direction. at the same time, the car does not hold a "line" as well, requiring a series of small left and right steering corrections.
- Steering
On warm days the steering on my 2006 BMW Z4 becomes unresponsive and unpredictable. On hot days it IS downright dangerous. I have read in many places that this IS due to a design defect in the steering column. One source who IS an ase-certified master technician says that the "BMW Z4 sticky…
On warm days the steering on my 2006 BMW Z4 becomes unresponsive and unpredictable. On hot days it IS downright dangerous. I have read in many places that this IS due to a design defect in the steering column. One source who IS an ase-certified master technician says that the "BMW Z4 sticky steering IS related to a manufacturing defect, that has been rectified as of 2007 and up. There IS a bearing located in the middle of the steering column that IS not sealed. With time and when hot, the lubricant gets dry and gums up. To make matters worse, there IS not a race for the bearing to ride in ' the inner race IS actually the steering shaft itself, which IS a poor design". my vehicle was built in 2006 and has only 54,000 miles on it. BMW apparently was aware of this problem and corrected it the following model year. There are many complaints on the nhtsa website about the same problem, which could get worse over time. BMW should issue a recall before someone gets seriously hurt.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- BMW airbag light illumination
BMW IS conducting a safety recall campaign on approximately 200,000 MY04 through MY06 subject vehicles built through 11/30/05 to correct the front passenger seat air bag occupant detection mat. The specific vehicles included in the recall aremy04- 06/ 5-series with standard and sport seats, my04-06/ x3-series and…
BMW IS conducting a safety recall campaign on approximately 200,000 MY04 through MY06 subject vehicles built through 11/30/05 to correct the front passenger seat air bag occupant detection mat. The specific vehicles included in the recall aremy04- 06/ 5-series with standard and sport seats, my04-06/ x3-series and MY06/ 3-series with sport seats. In addition, BMW will extend the warranty coverage of the passenger seat air bag occupant detection mat to 10-year/unlimited mileage on approximately 120,000 remaining my04-06 subject vehicles built through 11/30/05. The specific vehicles included in the extended warranty are my 06/ 6 series, my 06/ 3-series with standard seats, my04-05/ Z4, my04-06/ 7 series, my 06/ X5, and my04-06/ 5-series with comfort seats.the average frequency of failures among the extended warranty groups was less than 1/7TH of the recall vehicle groups.please see bmw's 08v-384 recall notification for further detailsdepending on seat configuration and vehicle geometry, the occupant detection mat can fatigue during use depending on the manner and frequency of the front passenger's entry and exit.specifically, over time, micro-cracks could develop in the side flanks of the mat causing a broken circuit.a brokencircuit can lead to the deactivation of the passenger air bag and the illumination of both the air bag warning light and the passenger air bag light.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10249437The basic conditions for initializing the power windows are not met.
- 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
- 10225126Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
- 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
- 10182619Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
- 10181214Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
- 10175267Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
- 10162416"Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The ""Service Engine Soon"" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is ""late"", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well."
- 10162404"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the "Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
- 10151300N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
- 10151247N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
- 10151023Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
- 10150224"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
- 10150173"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
- 10150160State Inspection and Emission (I/M) Test Fails Due To an Invalid VIN Number. The customer of an affected vehicle may fail to pass an I/M test due to a non-compliant 17digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read out and displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it is possible that only the last 7 digits of the VIN were entered into the DME, and positions 4 through10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.
- 10150095Intermittent Hydraulic Valve Adjuster (HVA) Noise. An occasional ticking or rattling noise from the camshaft hydraulic valve lifters (HVA) may occur during cold engine starts, due to frequent short-distance driving, or the noise may occur for an extended period of time even though the engine is at operating temperature. Improved parts were phased into production beginning on 10/1/2008 and fully implemented on November 31st 2008.
- 10149612Clicking/Popping Noise from Dash at Startup. The customer states that when the vehicle is started, or the ignition switch is turned on, there is a clicking/popping noise coming from the dash area. CAUSE Mis-alignment of the fresh air/recirculation flap gears.
- 10149441"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""B5116_ECSPPL2."""
- 10148273Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
- 10148179Diagnosis of Compound Brake System Complaints in M Vehicles. INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
- 10148120Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
- 10148087External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
- 10148018"?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho
- 10147242Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
- 10147136Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
- 10145306NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
- 10143564NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
- 10142910Front passenger seat occupancy (OC3) mat for srs: limited warranty extension to 15 years/unlimited miles
- 10052012BMW: battery has an increased demand due to developemental process of the electrical system. This IS causing the batter to need to undergo an energy diagnosis.
- 10042684BMW: on some vehicles, the high pressure fuel pump has an internal component that may fail and causing drivability symptoms such as erratic engine operation and longer starting times.
- 10041281BMW: the rear lamp IS not water tight due to cracks due to stress. Water may enter the lamp.
- 10040853BMW: a grinding noise IS coming from the differential during slow cornering. When turning a slip/stick effect IS created on the lining and steel discs incorporated in the differential clutch causes a grinding noise.
- 10040045BMW: a new technical support process has been created regarding transmission concerns.
- 10039765BMW: the service engine soon light IS on while driving. This IS a programming issue. Updated 1/4/12. Updated 4/24/12.
- 10037702BMW: when at lower speeds or stopping the engine idle dips too low because of a software problem.
- 10037700BMW: there may be excessive cranking before the vehicle starts. The service engine soon light may also be on with a lack of engine power.
- 10037464BMW: water IS leaking into the luggage compartment due to a damaged seal on rear vents.
- 10037025BMW: procedure for determining and replacing incandescent and halogen light bulbs under warranty.
- 10037010BMW: six different models equipped with the M54 engine could have valve covers break in cold weather and ruin the engine. This IS due to moisture accumulation.
- 10036980BMW: a new technical process IS being used on many models to determine the root cause of double-clutch transmission problems.
Every BMW Z4 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.