2008 BMW Z4
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2008 BMW Z4. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2008 BMW Z4. Newest first.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3…
Risk and remedy
Risk
An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.
Remedy
This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Risk and remedy
Risk
An electrical short can cause the parts within the PCV valve to melt, increasing the risk of a fire, even when the vehicle is not in use.
Remedy
BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notification by the end of October 2018. Owners may contact BMW customer service at 1-800-525-7417.
Owner complaints
19 complaints
What owners report most
Latest complaints
- Service brakes
This complaint is regarding a large number of 2008 BMW cars exhibiting the ABS failure light. Mine is a Z4 with @ 65K miles and was diagnosed by a certified mechanic as the ABS module failure - a high ($3000-$4000) cost repair. If you use this search term - "how common is bmw 2008 ABS module…
This complaint is regarding a large number of 2008 BMW cars exhibiting the ABS failure light. Mine is a Z4 with @ 65K miles and was diagnosed by a certified mechanic as the ABS module failure - a high ($3000-$4000) cost repair. If you use this search term - "how common is bmw 2008 ABS module failure?", you will see that a multitude of cars from 2008 (and in other years and models using the same module) are affected by and exhibit this dangerous issue. What has to happen for BMW to be forced to repairing this chronic, safety-compromising, and widespread issue? This is not something that happens to other cars as a result of age. This is a design flaw that directly affects safety. Now I would like to sell the car, but I can't afford to fix it and, in good conscience, I cannot sell it if it is dangerous.
- Engine and engine cooling
The contact owns a 2008 BMW Z4. The contact received notification of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was unavailable. The local dealer was contacted and confirmed that the part was not yet available. The contact stated that the…
The contact owns a 2008 BMW Z4. The contact received notification of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was unavailable. The local dealer was contacted and confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
- Vehicle speed control
Idling in gear (automatic transmission) at a drive thru. car suddenly tried to accelerate. put car in park and engine continued to increase to max rpms. I shut off the engine at the ignition. Restarted engine and idled normally.
- Air bags
TL* the contact owns a 2008 BMW Z4. The contact stated that for several months the air bag warning indicator was flashing. The contact stated that the air bag warning light was constantly illuminated. The vehicle was not taken to the dealer or an independent mechanic for a diagnostic test. The manufacturer was not notified of the failure. The vehicle was not repaired. The approximate failure mileage was 60,000.
- Air bags · Air bags › Sensor › Occupant classification · Seats
Recently purchased a 2008 BMW Z4. After a week of ownership the airbag light came on. Fault code points to the passenger seat occupancy sensor OC3. BMW issued a 15 year extended warranty to many BMW models including the 2006 and 2007 Z4 with comfort seats, but not to the 2008 model. This repair costs upwards of $1500 and IS safety related. BMW needs to step up and cover all affected models!
- Air bags · Air bags › Sensor › Occupant classification · Air bags › Sensor › Occupant classification › Front passenger
The airbag red light on dash appeared and stayed on,also passenger yellow airbag light stays on .took to BMW dealer they informed me that the passenger seat occupancy sensor mat was defective and needed to be replaced at a cost around 1,600.00 . error code 93C3 they informed me with this…
The airbag red light on dash appeared and stayed on,also passenger yellow airbag light stays on .took to BMW dealer they informed me that the passenger seat occupancy sensor mat was defective and needed to be replaced at a cost around 1,600.00 . error code 93C3 they informed me with this problem I do not have any airbag protection . This IS a safety problem and I believe they have repaired other models but not this model . why ?
- Air bags · Air bags › Sensor › Occupant classification
Dashboard airbag warning light came on - obd scan indicates the passenger seat OC3 airbag sensor mat has failed. I believe this means the vehicle can no longer detect if there IS a child in the passenger seat, and will deploy airbags regardless of passenger weight. BMW has a service bulletin for many other models and years (including my Z4 model - but not yet for my 2008 model year).
- Engine and engine cooling › Exhaust system › Emission control › Crankcase (pcv)
TL* the contact owns a 2008 BMW Z4. The contact received notification of nhtsa campaign number: 17v683000 (engine and engine cooling); however, the parts to do the repair were unavailable. The dealer was not contacted. The manufacturer was notified and confirmed that the recall parts were not available. The contact had not experienced a failure. Vin tool confirms parts not available. *tt
- Air bags · Air bags › Sensor › Occupant classification
A failed front passenger air bag seat sensor mat causes the air bag warning lamp and the passenger air bag 'on-off' lamp to be illuminated simultaneously. in august 13, 2008, BMW issued a voluntary recall involving front passenger seat sensor mat on U.S.A. Model bmws regarding the front passenger…
A failed front passenger air bag seat sensor mat causes the air bag warning lamp and the passenger air bag 'on-off' lamp to be illuminated simultaneously. in august 13, 2008, BMW issued a voluntary recall involving front passenger seat sensor mat on U.S.A. Model bmws regarding the front passenger air bag seat sensor mat involving approximately 200,000 model year 2004-06 vehicles. My similarly affected 2008 vehicle was not included in the recall. The recall also states that in this situation, BMW recommends customers not to use the front passenger seat and have the vehicle serviced immediately. When I called my local BMW dealer, I was advised of a $152 shop diagnosis fee and a likely repair cost of $1800. This IS a prohibitive cost for a factory defect on a 73 year old senior citizen living on social security.
- Engine
TL* the contact owns a 2008 BMW Z4. The contact stated that nhtsa campaign number: 17v683000 (engine and engine cooling) exceeded a reasonable amount of time for repair. The dealer was not contacted. The manufacturer was contacted and stated that the parts were unavailable for the repair. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
'The vehicle was purchased used from a dealer in october 2012, with about 30600 miles;, current mileage IS about 57400. the airbag disabled light in instrument cluster started acting up several months ago; now it IS on at all times, whether or not a passenger IS in the seat or the car IS in motion…
'The vehicle was purchased used from a dealer in october 2012, with about 30600 miles;, current mileage IS about 57400. the airbag disabled light in instrument cluster started acting up several months ago; now it IS on at all times, whether or not a passenger IS in the seat or the car IS in motion or stopped. A scan of the vehicle shows a defective passenger occupancy sensor / mat. resetting the light with the scan tool does not fix the problem. many 2008 BMW models were recalled for a similar problem, but not the Z4, even though there are several complaints listed here. the local BMW dealer wants $152.00 shop diagnosis fee and a replacement mat switch could be $1800.00. this IS a safety issue known by the manufacturer from the beginning and should be included in the recall.
- Air bags
Takata recall airbag light on at all times on the instrument cluster. a scan of the vehicle shows a defective passenger seat cushion sensor. resetting the light with the scan tools does not fix the problem, the light goes back on immediately and stays on whether there IS a passenger seated in…
Takata recall airbag light on at all times on the instrument cluster. a scan of the vehicle shows a defective passenger seat cushion sensor. resetting the light with the scan tools does not fix the problem, the light goes back on immediately and stays on whether there IS a passenger seated in the vehicle or not. it does not make a difference if the vehicle IS stationary or moving. I purchased the vehicle used on may 7TH 2016 and the light was on when I purchased the vehicle.
- Steering
Very erratic steering. Crossing the crown of a road will pull one way and then quickly pull in the opposite direction unlike anything I have ever driven. Also same effect with trying to stay in lanes with any common deviation. This IS worst at hwy speeds but does occur at lower speeds as well.
- Air bags
Light indicating passenger airbag was disabled began coming on while passenger in the seat. within a few weeks of noticing this, passenger airbag always indicates off. many 08 models were recalled for passenger airbag mat failures, but not the Z4 (too few cars made?) I called bmw-usa and a case agent called me back. BMW would take no responsibility for the failure.
- Steering
Just bought a used 2008 Z4. Cannot drive straight line, car goes all over the road. Steering has "stick-slip" effect. Car wanders from right to left and left to right. Got rubber elements in front axle replaced, 4 wheel alignment, ..., no change. Appears to be a power steering issue. *tr
- Electrical system · Steering
While turning on a constant radius clover-leaf on-ramp (right or left), a sudden change in steering angle was required to avoid an obstacle. as the electrically-assisted steering was quickly adjusted, a flat spot (or a heavy spot or a delay in boost) in the steering wheel/feel was encountered. in…
While turning on a constant radius clover-leaf on-ramp (right or left), a sudden change in steering angle was required to avoid an obstacle. as the electrically-assisted steering was quickly adjusted, a flat spot (or a heavy spot or a delay in boost) in the steering wheel/feel was encountered. in other words, more force was required than expected to quickly change the steering angle. if this IS normal, it could interfere with emergency maneuvers to avoid obstacles. personally, I find it to be unsafe as the steering feel IS unpredictable. this unpredictable steering feel occurs anytime I need to make an abrupt change in steering angle. *tr
- Electrical system · Steering
After starting up the car (but during ignition, the key slipped in my fingers causing a missed start, I therefore had to turn the key again to get engine to turn over.) and driving from my driveway, there was a complete failure of the steering assist which caused extremely difficult…
After starting up the car (but during ignition, the key slipped in my fingers causing a missed start, I therefore had to turn the key again to get engine to turn over.) and driving from my driveway, there was a complete failure of the steering assist which caused extremely difficult steering/cornering. I pulled over, thinking it had to do with the missed start, turned off the engine and restarted it; still no power assist. Took it to the dealer, they were able to do a computer reset which restored power assist, but told me they could not say if or when it would happen again. I could opt for complete steering column replacement at a cost of $3500! I've owned the car for 5 months and maybe put 400 miles on it? This IS too dangerous a thing to let go, I don't think this IS safe. This should be recalled. *tr
- Steering
Steering failure with dtc failure and brake yellow warning lights. must fight with car to drive straight wants to veer to the left with shaky steering. *tr
- Wheels
All four rims are bent. The vehicle has never been taken off-road, nor has the vehicle encountered major potholes. A logical explanation for this occurrence IS shoddy manufacturing. Bent rims potentially cause hazardous driving conditions. *tr
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10249437The basic conditions for initializing the power windows are not met.
- 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
- 10225126Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
- 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
- 10182619Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
- 10181214Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
- 10175267Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
- 10162416"Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The ""Service Engine Soon"" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is ""late"", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well."
- 10162404"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the "Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
- 10151300N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
- 10151247N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
- 10151023Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
- 10150224"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
- 10150173"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
- 10150160State Inspection and Emission (I/M) Test Fails Due To an Invalid VIN Number. The customer of an affected vehicle may fail to pass an I/M test due to a non-compliant 17digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read out and displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it is possible that only the last 7 digits of the VIN were entered into the DME, and positions 4 through10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.
- 10150095Intermittent Hydraulic Valve Adjuster (HVA) Noise. An occasional ticking or rattling noise from the camshaft hydraulic valve lifters (HVA) may occur during cold engine starts, due to frequent short-distance driving, or the noise may occur for an extended period of time even though the engine is at operating temperature. Improved parts were phased into production beginning on 10/1/2008 and fully implemented on November 31st 2008.
- 10149612Clicking/Popping Noise from Dash at Startup. The customer states that when the vehicle is started, or the ignition switch is turned on, there is a clicking/popping noise coming from the dash area. CAUSE Mis-alignment of the fresh air/recirculation flap gears.
- 10149441"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""B5116_ECSPPL2."""
- 10148273Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
- 10148179Diagnosis of Compound Brake System Complaints in M Vehicles. INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
- 10148120Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
- 10148087External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
- 10148018"?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho
- 10147242Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
- 10147136Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
- 10145306NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
- 10143564NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
- 10056099BMW: when using iphone, various connectivity failures occur, such as disconnection of call, list of contacts incomplete, due to the variants and software used. Model 2008-2014.
- 10052012BMW: battery has an increased demand due to developemental process of the electrical system. This IS causing the batter to need to undergo an energy diagnosis.
- 10045279BMW: a failure of the turbocharger wastegates, caused by a defect, has an emissions extended warranty, 8 years or 82,000 miles, whichever comes first, not otherwise falling within coverage exclusion.
- 10042684BMW: on some vehicles, the high pressure fuel pump has an internal component that may fail and causing drivability symptoms such as erratic engine operation and longer starting times.
- 10041281BMW: the rear lamp IS not water tight due to cracks due to stress. Water may enter the lamp.
- 10041276BMW: service engine soon light IS on with a fault code stored. Internal dmtl pump failure.*rm
- 10040853BMW: a grinding noise IS coming from the differential during slow cornering. When turning a slip/stick effect IS created on the lining and steel discs incorporated in the differential clutch causes a grinding noise.
Every BMW Z4 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.