2010 Dodge RAM 3500
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Dodge › RAM 3500 › 2010
These records cover every 2010 Dodge RAM 3500. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
9 recalls name the 2010 Dodge RAM 3500. Newest first.
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
Risk and remedy
Risk
In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the…
Risk and remedy
Risk
Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy
Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
Chrysler (FCA US LLC) is recalling certain model year 2009 Dodge Durango and Chrysler Aspen vehicles manufactured January 17, 2007, to December 18, 2008, and 2010 RAM 3500 cab chassis manufactured September 25, 2009, to February 1, 2010. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler has notified owners, and dealers will replace the driver's frontal air bag inflator, free of charge. The recall began January 11, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S92. Note: This recall covers vehicles that were accidentally excluded from recall 15V-313.
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger Police vehicles, 2007-2013 RAM 3500 Cab Chassis, 2008-2013 RAM 4500 and 5500 Cab Chassis, and 2013 RAM 2500 and 3500 vehicles. The affected vehicles have a 220 amp alternator that may suddenly fail.
Risk and remedy
Risk
If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy
Chrysler will notify owners, and dealers will replace the alternator with a revised alternator, free of charge. The recall began on December 23, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S68.
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge…
Risk and remedy
Risk
These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
Risk and remedy
Risk
If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
Remedy
Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.
Risk and remedy
Risk
A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.
Remedy
Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.
Chrysler IS recalling certain model year 2008-2011 dodge RAM 2500/3500 4X4, manufactured from february 14, 2008, through march 28, 2011; model year 2008-2011 dodge RAM 3500 cab chassis 4X2, manufactured from february 14, 2008, through march 28, 2011; and model year 2008 dodge RAM 1500 mega cab 4X4, manufactured from february 14, 2008, through august 15…
Risk and remedy
Risk
This condition could result in the potential loss of directional stability in the left hand front wheel, increasing the risk of a crash.
Remedy
Dealers will inspect the tie rod ends for relative orientation and replace the left outer tie rod as required and perform a front end toe alignment as needed. this service will be performed free of charge. the safety recall began on october 3, 2011. owners may contact chrysler at 1-800-853-1403.
Owner complaints
150 complaints3 involved a crash4 involved a fire6 injuries
What owners report most
Latest complaints
- Air bags
The contact owns a 2010 Dodge Ram 3500. The contact stated while driving approximately 30 MPH, the air bag warning light illuminated. The contact stated that the vehicle was taken to an independent mechanic who diagnosed the vehicle and determined that the driver's side air bag needed to be…
The contact owns a 2010 Dodge Ram 3500. The contact stated while driving approximately 30 MPH, the air bag warning light illuminated. The contact stated that the vehicle was taken to an independent mechanic who diagnosed the vehicle and determined that the driver's side air bag needed to be replaced. The mechanic informed the contact of NHTSA Campaign Number: 16V947000 (Air Bags). The contact called a dealer and was informed that the VIN was not included. The manufacturer was not made aware of the failure. The failure mileage was approximately 146,000.
- Electrical system › Ignition
The contact owns a 2010 Dodge Ram 3500. The contact stated that while driving at various speeds, the vehicle shut off without warning. The contact stated that the failure occurred after driving over a bump in the roadway. The contact stated that occasionally, while wiggling the ignition key the…
The contact owns a 2010 Dodge Ram 3500. The contact stated that while driving at various speeds, the vehicle shut off without warning. The contact stated that the failure occurred after driving over a bump in the roadway. The contact stated that occasionally, while wiggling the ignition key the engine would turn on before shutting off. The vehicle was taken to the local dealer who determined that the ignition switch was faulty and needed to be replaced. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in the NHTSA Campaign Number: 14V373000 (Electrical System). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 270,000.
- Electrical system · Steering · Vehicle speed control
Fobik key ignition vibrates causing switching from (RUN) position to (ACC) position, shutting off the engine and making it almost impossible to steer a 3000kg machine without power steering increasing the risk for accidents.
- Electrical system · Engine · Fuel/propulsion system
Truck totally destroyed by spontaneous fire, suspected to be related to short in radio or dashboard. Assessment done by fire department and truck paid off by Progressive Insurance but no compensation for contents of truck. Truck in driveway, not running and fire damaged adjacent vehicle at cost of $7000 paid by vehicle owner and USAA insurance.
- Power train
My husband, our son, and I were traveling down the highway at about 60-65mph when we started hearing a low winding sound. Seconds later, before my husband could get the truck over to the shoulder of the road, there was a loud banging sound coming from underneath the truck that sounded like…
My husband, our son, and I were traveling down the highway at about 60-65mph when we started hearing a low winding sound. Seconds later, before my husband could get the truck over to the shoulder of the road, there was a loud banging sound coming from underneath the truck that sounded like something was coming through the floorboard. He was finally able to get the truck pulled to the shoulder of the road but wasn't able to put the truck in the park position. He had to use the park brake to get the truck to completely stop. Once the tow truck safely lifted the truck, you could clearly see gears hanging amd what looked to be remains of the transfer case. The truck was towed to a body shop where several codes were discovered, which all pertained to the truck going into 4wd by itself without any warning and unknowing to the driver. This glitch is what appears to have caused the transfer case to grenade, further causing damage to the drive shaft and smashing the fuel line. We, as owners, had the transfer case serviced and fluids flushed just two weeks prior to this happening After further investigation and conversations with the local Dodge dealer, it appears that this has happened in several situations yet no safety recalls have been issued. There is a national backorder for transfer cases for our particular year which is a red flag. We're now left with an over $8100.00 bill and everyone pointing the finger at each other. This could have ended tragically had there been more traffic on the road when the truck began stalling on the busy interstate.
- Power train
My family and I were traveling down the interstate about 60-65mph in 2 wheel drive when out of nowhere we started hearing a whining/roaring noise that quickly got louder. Seconds later, there was a loud rumbling noise that sounded like something was coming through the floorboard of the truck.…
My family and I were traveling down the interstate about 60-65mph in 2 wheel drive when out of nowhere we started hearing a whining/roaring noise that quickly got louder. Seconds later, there was a loud rumbling noise that sounded like something was coming through the floorboard of the truck. Luckily, I was able to steer the truck to the shoulder of the road and get it to stop, but the truck would not go into park. I had to use the park brake to make sure that it wouldn't roll. After the tow truck arrived and safely jacked the truck up, we immediately noticed that it was the transfer case that had exploded. Gears were hanging out in plain site and it caused a bend in my front driveshaft. There were no warning signs and I had just had the transfer case and my transmission serviced and flushed 2 weeks prior. This put my family's and other lives in danger because had there been more traffic on the road at the time this happened, I wouldn't have had time or room to maneuver my truck safely to get it off the road. We could have been rear ended or had broken parts fly off the truck, that would have been out of my control. The truck was towed to the shop where I had the transfer case serviced, but as of now there's a national backorder on transfer cases for this truck. In speaking with the dealer and doing my own research, I've also learned that there has been a recall on the transfer cases of 2016 and newer Ram 3500 trucks. This needs to be looked into asap. Codes pulled from the truck at the auto shop where the truck currently is are c1404, c1405, c140d stating that the transfer case motor puts the system in 4wd by itself while driving without any warning.
- Electrical system
WIN ignition module has slowly been causing difficult starting problems. Now, over even slight bumps, the sloppiness in the connection between the key and the WIN module allows the key to move and the vehicle to shut off while driving. This is becoming more and more common and is very dangerous.…
WIN ignition module has slowly been causing difficult starting problems. Now, over even slight bumps, the sloppiness in the connection between the key and the WIN module allows the key to move and the vehicle to shut off while driving. This is becoming more and more common and is very dangerous. Just on my 10 minute drive home from work today, it occurred 4 times. One time, I had just turned right on a red light (with plenty of space between me and oncoming traffic) and the truck shut off completely. Without the key being in the exact right position, I had difficulty restarting the truck and could have been very dangerous to me and the vehicle coming toward me.
- Electrical system · Service brakes · Steering
While driving, the truck just shuts off. Resulting in loss of steering, lights and power breaks.
- Fuel/propulsion system
During fueling with the vehicle stationary, fuel will spill out of spout when tank IS full as fuel dispenser shuts off. This happens any time vehicle IS fueled.
- Fuel/propulsion system
While traveling on the highway at approximately 75 mph with a load in the bed of the truck and towing a trailer, the vehicle engine stopped, eliminating power steering and power brakes. afte having the vehicle towed to the dealer for diagnosis, it was determined that the cp$ high pressure fuel pump had discintegrated.
- Air bags
TL* the contact owns a 2010 RAM 1500. The contact stated while sitting in the parking lot in the vehicle, the airbags independently deployed with no warning. The contact took the vehicle to (autonation chrysler dodge jeep RAM and fiat johnson city, 3700 bristol hwy, johnson city, tn 37601) where…
TL* the contact owns a 2010 RAM 1500. The contact stated while sitting in the parking lot in the vehicle, the airbags independently deployed with no warning. The contact took the vehicle to (autonation chrysler dodge jeep RAM and fiat johnson city, 3700 bristol hwy, johnson city, tn 37601) where the vehicle was not diagnosed nor repaired. The manufacturer was notified of the failure. The failure mileage was 150,000. *bf consumer stated due to the explosion may have resulted in some hearing loss and continuous noise in the head of the consumer. Insurance company declared vehicle totaled.*jb
- Electrical system
TL* the contact owns a 2010 RAM 1500. The contact stated that the switch from heat to air condition was inoperable. The vehicle was taken to (chrysler dodge jeep ram315 goodman rd e, southaven, ms 38671 (662) 349-3006) where it was diagnosed that the gear actuator failed needed to be replaced. The…
TL* the contact owns a 2010 RAM 1500. The contact stated that the switch from heat to air condition was inoperable. The vehicle was taken to (chrysler dodge jeep ram315 goodman rd e, southaven, ms 38671 (662) 349-3006) where it was diagnosed that the gear actuator failed needed to be replaced. The vehicle was not repaired. However, the failure recurred. The manufacturer was made aware of the failure and informed the contact that the vin was not subjected to a recall. The failure mileage was unknown.
- Unknown or other
The tipm malfunctioned and made vehicle operate erratically while in motion. Smelled an electrical issue. Got to a garage and was told it was probably the tipm.*dt*jb
- Electrical system · Engine · Steering
TL* the contact owns a 2010 dodge RAM 3500. The contact stated that the ignition module solenoid malfunctioned and caused the key to fall out of the ignition while the vehicle was in motion. In addition, the steering would not lock when the vehicle was parked. Green dodge (3801 wabash ave…
TL* the contact owns a 2010 dodge RAM 3500. The contact stated that the ignition module solenoid malfunctioned and caused the key to fall out of the ignition while the vehicle was in motion. In addition, the steering would not lock when the vehicle was parked. Green dodge (3801 wabash ave, springfield, il 62711, (217) 522-1222) and the manufacturer were contacted and stated that the vehicle was not included in a recall. The manufacturer referred the contact to nhtsa. The vehicle was not diagnosed or repaired. The failure mileage was 86,400. The vin was invalid.*jb *tr*jb
- Steering
Traveling on highway between 60 to 70 miles an hour driving over a rough part of road, pot whole, or bump the front tires start wobbling severely causing loss of control of vehicle until I reduce speed to 40 miles or under then I'm able to steer off to side of road. Have to come to a complete stop…
Traveling on highway between 60 to 70 miles an hour driving over a rough part of road, pot whole, or bump the front tires start wobbling severely causing loss of control of vehicle until I reduce speed to 40 miles or under then I'm able to steer off to side of road. Have to come to a complete stop before tires stop wobbling I've been to dealership four times and spent over 5000.00 dollars and the problem still exist
- Engine
TL* the contact owns a 2010 dodge RAM 3500. While driving 60 mph, the vehicle decelerated to 10 mph on its own. There were no warning indicators illuminated. The vehicle was towed to an independent mechanic who diagnosed that a new camshaft was needed. The mechanic also suggested that the contact…
TL* the contact owns a 2010 dodge RAM 3500. While driving 60 mph, the vehicle decelerated to 10 mph on its own. There were no warning indicators illuminated. The vehicle was towed to an independent mechanic who diagnosed that a new camshaft was needed. The mechanic also suggested that the contact take the vehicle to a dealer. The contact called pine belt chrysler jeep new jersey (88, 1400 ocean ave, lakewood, nj 08701, (732) 719-4651), but they refused to service the vehicle for free because it was out of warranty. The vehicle was not repaired. The manufacturer was made aware of the failure and did not assist. The failure mileage was 92,000.
- Power train
2010 dodge RAM. Consumer writes in regards to brake transmission shift interlock safety recall. *Ld *tr
- Air bags
TL* the contact owns a 2010 dodge RAM 3500. The contact stated that the air bag indicator illuminated and remained lit. The vehicle was taken to kings dodge chrysler jeep RAM (4486 kings water dr, cincinnati, oh 45249) where it was diagnosed that the driver's side curtain air bag had a short…
TL* the contact owns a 2010 dodge RAM 3500. The contact stated that the air bag indicator illuminated and remained lit. The vehicle was taken to kings dodge chrysler jeep RAM (4486 kings water dr, cincinnati, oh 45249) where it was diagnosed that the driver's side curtain air bag had a short circuit that needed to be replaced. The manufacturer was contacted and stated that the vehicle was not included in any recalls. The vehicle was not repaired. The failure mileage was 159,650. *Tt*jb consumer seat belt/airbag light was visable at least 2-3 years.*jb
- Steering
TL* the contact owns a 2010 dodge RAM 3500. The contact stated that the power steering seized when making turns at slow speeds. The vehicle was taken to thomas chrysler dodge jeep (67791 mall rd, st clairsville, oh 43950, (877) 268-3302) and they upgraded and replaced the steering box, but the…
TL* the contact owns a 2010 dodge RAM 3500. The contact stated that the power steering seized when making turns at slow speeds. The vehicle was taken to thomas chrysler dodge jeep (67791 mall rd, st clairsville, oh 43950, (877) 268-3302) and they upgraded and replaced the steering box, but the failure recurred. The vehicle was taken back to the dealer and they replaced the power steering pump to troubleshoot the failure. The manufacturer stated that the vehicle was out of warranty and they would not assist. The failure mileage was 46,000. *Tt consumer stated power steering goes out and cannot turn. *Jb
- Steering · Suspension
Driving on interstate highway at 70 miles per hour. Went over a bridge and front end started shaking violently. Stopped and looked for a problem. Could not see any issues. Thought it may be mud coming out of wheels causing a balance problem. Continued trip. Drove about 130 miles. Went over small…
Driving on interstate highway at 70 miles per hour. Went over a bridge and front end started shaking violently. Stopped and looked for a problem. Could not see any issues. Thought it may be mud coming out of wheels causing a balance problem. Continued trip. Drove about 130 miles. Went over small bumps and front end started violently shaking.had to stop on side of road. Came home and researched problem. Found others have same problem referred to as "death wobble" this could cause problems if in heavy traffic or if pulling a trailer. this truck only has 53235 miles and IS used mainly for on highway use.
- Power train
TL* the contact owns a 2010 dodge RAM 3500. The contact received notification of nhtsa campaign number: 17v821000 (power train); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer…
TL* the contact owns a 2010 dodge RAM 3500. The contact received notification of nhtsa campaign number: 17v821000 (power train); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (lithia chrysler jeep dodge RAM of pocatello, 633 bullock st, pocatello, ID 83201, (208) 904-3369) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Parts distribution disconnect.
- Service brakes
2010 dodge RAM 3500. Consumer writes in regards to brake transmission shift interlock. *Ld *js
- Wheels
Released the emergency brake when getting ready to start rolling was towing a trailer. Heard a snap after rolling a few feet, the emergency brake did not disengage when released and the backing plate on the caliper snapped off. I believe the cold freezing temps tired outside affected the engagement mechanism and prevented it from actually releasing the emergency brake .
- Power train · Steering
While my dealership has taken care of my 3 issues here, I want to let folks know: front end steering. 2 yrs after purchase, I started to have front end steering shimmy. The first time, the tie rod became loose, and was replaced by the dealership. 2ND time, I was backing out of my driveway, (loose…
While my dealership has taken care of my 3 issues here, I want to let folks know: front end steering. 2 yrs after purchase, I started to have front end steering shimmy. The first time, the tie rod became loose, and was replaced by the dealership. 2ND time, I was backing out of my driveway, (loose sand) and the tie rod end literally snapped in 2, rendering the steering useless. Reading the ladies story about her husband being ticketed for falling asleep when I have had it happen to my truck I thought I needed to speak out. drive line issue: the support bearing on the drive shaft, went while driving with out notice. Luckily I was driving down my drive way which IS about 500 feet long and wasn't going but about 15 mph. It had to be towed in and was covered under warranty. I love my truck and currently have 136K miles on it. The fuel mileage wasn't impressive but minor mods have brought it closer to 20 mpg when empty. I think I still have pictures of both the snapped tie rod and when it was wore out. Luckily I wasn't going fast when the snap happened, but the sand shouldn't have torqued the tie rod so hard to snap it when backing out of the drive way.
- Steering
Vehicle was in motion on highway,doing approximately 67 mph, the drivers front wheel hit a bump in road and the front end started to shimmy and vibrate uncontrollably."the death rattle".when this happens, you have no control of the vehicle.i believe this was the steering issue in the 2015 RAM buy back.why are these defective trucks still being sold?
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Electrical overstress
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air…
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010205Plate - Planetary
- 11004993Replacement Totally Integrated Power Module (TIPM) Displays Incorrect Vehicle Identification Number (VIN) Current and Active
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10242717Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
- 10229031Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
- 10227983If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
- 10225951CONNECTOR Trailer Tow,WIRING Trailer Tow,CONNECTOR 7 Way,WIRING Rear Bumper If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content
- 10223854Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10222885CONNECTOR/WIRING, Trailer Tow If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content
- 10221380CONNECTOR/WIRING, Trailer Tow If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220868Transfer Case Gear Motor/Actuator Installation Guidelines.
- 10220837GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.
- 10220687Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
- 10220496PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220098Authentic Mopar Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar Glass.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10218178Part Description: Thermostat, Engine Issue Description: Important! There has been an application change to the Cummins turbo diesel thermostat. When replacing a thermostat confirm the correct replacement is choosen.~ 2010, 2011, and 2012 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature has been increased to 200 degrees requiring thermostat 68067109AA.~ 2009, 2013, and 2014 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature is 190 degrees requiring thermostat 68005464AA.~ These thermostats are not interchangeable and doing so will result in reduced engine performance.
- 10217426On Board Diagnosis (OBD) Monitor Readiness
- 10216423Advanced Field Action Communication ? N0802072013 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 through 2012 model year: (DS) Ram Truck (ND) Dodge Dakota (HB) Dodge Durango (HG) Chrysler Aspen NOTE: All of the above involved vehicles are equipped with a Chrysler 9.25? rear axle (sales code DRB) or C235 rear axle (sales code DRN). The above vehicles may have been built with a rear axle pinion nut that can loosen, which could result in the rear axle locking up. This could cause a loss of vehicle control and/or a crash with little warning. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Dealers will be notified of the launch of this safety recall by way of established methods used in the past.
- 1021641868069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~
- 10216415Fluid Leak From Washer Reservoir (X44 Warranty Extension 5 Years/100,000 Miles (160,000 KMS)) This bulletin involves inspecting and/or replacing the washer reservoir. A customer may have a condition where fluid is leaking from the washer reservoir. On further inspection the technician may find cracks in the reservoir by the washer pump pocket.
- 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10216390Malfunction Indicator Lamp Illumination Due To Oxygen Sensor This bulletin involves replacement of the Oxygen Sensor Connectors for any Oxygen Sensor related DTC. Do NOT replace any parts prior to performing this bulletin and the Verifications test below. If the vehicle has any of the following DTC?s for O2 Sensors, Stored, Pending or Active, perform the Repair Procedure. ? P013A O2 Sensor 1/2 Slow Response - Rich To Lean (Soot related code, see note) ? P013B O2 Sensor 1/2 Slow Response - Lean To Rich (Soot related code, see note) ? P014C O2 Sensor 1/1 Slow Response - Rich To Lean (Soot related code, see note) ? P014D O2 Sensor 1/1 Slow Response - Lean To Rich (Soot related code, see note) ? P0030 O2 Sensor 1/1 Heater Circuit ? P0031 O2 Sensor 1/1 Heater Circuit Low ? P0032 O2 Sensor 1/1 Heater Circuit High ? P0036 O2 Sensor 1/2 Heater Circuit Malfunction ? P0037 O2 Sensor Heater Circuit Low 1/2 ? P0038 O2 Sensor Heater Circuit High 1/2 ? P0053 O2 Sensor Heater 1/1 Resistance ? P0054 O2 Sensor Heater 1/2 Resistance ? P064D Internal Control Module 02 Sensors Processor Performance - Bank 1 ? P0131 1/1 02 Sensor Shorted To Ground ? P0132 1/1 02 Sensor Shorted To Voltage ? P0135 O2 Sensor 1/1 Heater Performance ? P0137 1/2 02 Sensor Shorted To Ground ? P0138 1/2 02 Sensor Shorted To Voltage ? P0141 O2 Sensor 1/2 Heater Performance ? P113C O2 Sensor Power Supply Circuit Performance ? P2195 O2 Sensor 1/1 Out Of Range High ? P2196 O2 Sensor 1/1 Out Of Range Low ? P22AB O2 Sensor Positive Current Control Circuit/Open - Bank 1 Sensor 2 ? P22AE O2 Sensor Reference Voltage Circuit/Open - Bank 1 Sensor 2 ? P22B2 O2 Sensor Negative Current Control Circuit/Open - Bank 1 ? P22B5 O2 Sensor 1/2 Pump Cell Current Trim Circuit Open ? P2237 O2 Sensor 1/1 Pump Cell Current Circuit Low ? P2243 O2 Sensor 1/1 Reference Voltage Circuit Open ? P2251 O2 Sensor 1/1 Negative Current Control Circuit/Open ? P2270 O2 Sensor 1/2 Out Of R
- 10216348Heavy Duty Filtration MOPAR Retrofit or Add On Parts Available
- 10216188On Board Diagnosis (OBD) Monitor Readiness
- 10216003Part Description: Integrated Trailer Brake Module Issue Description: Before replacing an Integrated Trailer Brake Module (ITBM) please review the following items.~ 1. The ITBM does not control the trailer lights. If the trailer lights are not working, do not change the ITBM.~ 2. If the Diagnostic Trouble Code(DTC) reported by the ITBM is C10C7-11 "Electronic Trailer Brake Control Output Short to Ground" or C10C7-12 "Electronic Trailer Brake Control Output Short to Battery", please verify the wiring on the trailer. The purpose of this faults is to protect the ITBM output from faulty trailer wiring.~ 3. If the customer complaint is ITBM not detecting the trailer connection. Do not change the ITBM until the system has been verified with load simulation and confirmed that ITBM is not recognizing the load. If load simulation indicates that the ITBM is operating properly, please verify the trailer wiring.~ 4. ITBM output will not be available if a trailer is not connect and plugged into the vehicle. The ITBM must detect a trailer before you will get trailer brake output.~ 5. Please follow the service manual procedures before changing the ITBM.~ This part can only be used as a replacement on vehicles with the Integrated Trailer Brake system already installed. Do not attempt to use this module for the purpose of adding the Integrated Trailer Brake system to a vehicle that was not originally equipped. You will encounter configuration difficulties. MOPAR has developed a kit, part number 82212548 to be used for installation of the Integrated Trailer Brake system on vehicles.
- 10215990Cummins 6.7L Turbo Diesel Common Diagnostic Process New 6.7L CumminsTurbo Diesel Common Diagnostic Process is now available as part of the standard diagnostic process located in TechCONNECT>Service Info.
- 10215976MIL Illumination Due to P2000, P2A00 and/or P2A01 FRONT O2 sensor. Customer may experience MIL illumination. Further investigation by the technician may find one or more of the following DTC(s) present: P2000 - NOX Absorber Efficiency Below Threshold - Bank 1. P2A00 - O2 Sensor 1/1 Circuit Performance. P2A01 - O2 Sensor 1/2 Circuit Performance.
- 10215879Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
- 10214527CONNECTOR/WIRING, Trailer Tow If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content
- 10212290Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
- 10190615Transfer Case Gear Motor/Actuator Installation Guidelines.
- 10190584GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.
- 10189383MIL Illumination Due to P2000, P2A00 and/or P2A01 This bulletin involves verifying all service bulletins related to high sooting issues have been properly addressed, inspecting both Oxygen (O2) sensors and either cleaning the sensors or replacing sensors, and installing an O2 Sensor Shield on the exhaust pipe in the area of the FRONT O2 sensor. Customer may experience MIL illumination. Further investigation by the technician may find one or more of the following DTC(s) present: ? P2000 - NOX Absorber Efficiency Below Threshold - Bank 1. ? P2A00 - O2 Sensor 1/1 Circuit Performance. ? P2A01 - O2 Sensor 1/2 Circuit Performance.
- 10189382Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software.Trucks exhibiting any DTC related to Oxygen Sensor, Oxygen Sensor Module or communication to the Oxygen Sensor Module also require that Service Bulletin?s 25-004-12 (or later bulletin) must be performed (if not previously performed). Pick up trucks equipped with a 6.7L Cummins diesel have a number of software improvements/enhancements available. This SB will include improved robustness for DTC's: P2000 - NOX ABSORBER EFFICIENCY BELOW THRESHOLD P1451 - DIESEL PARTICULATE FILTER SYSTEM PERFORMANCE P0101 - MASS AIR FLOW SENSOR "A" CIRCUIT PERFORMANCE P046C - EGR POSITION SENSOR PERFORMANCE P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT P051B - CRANKCASE PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD P2262 - TURBOCHARGER BOOST PRESSURE NOT DETECTED - MECHANICAL P2609 - INTAKE AIR HEATER SYSTEM PERFORMANCE P245B - EGR COOLER BYPASS STATUS LINE INTERMITTENTVehicles flashed to address the above codes should be driven and repair validated. If code(s) return, follow diagnostic procedures available in DealerCONNECT/TechCONNECT.Improvements other than DTC robustness or enhancements: O2 Sensor cleaning cycle Correct Charge Air Cooler (CAC) out voltage reading in WiTech Improve idle shutdown messages Add ability to read Exhaust Manifold Presure (EMP) sensor value in WiTech Display correct Exhaust Gas Recirculation (EGR) position in WiTech Make Grid Heater off time selectable in WiTec Display correct alternator voltage in WiTech Turn Low Voltage Idle Up Off MIL on with no DTC Ability to read EGR valve gap on wiTECH Erroneous, brief brake lamp flash at key onSecure Bootloader softwareIf the Engine Control Module (ECM) does not have a calibration installed, or has an unapproved calibration installed then the ECM will
Every Dodge RAM 3500 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.