2006 Nissan Altima
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Nissan › Altima › 2006
These records cover every 2006 Nissan Altima. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2006 Nissan Altima. Newest first.
On certain passenger vehicles equipped with a 2.5L engine, the crankshaft position sensor can overheat causing a brief interruption in the signal output from the sensor.
Risk and remedy
Risk
If the interruption in the signal from the crankshaft position sensor IS so brief that the electronic control module (ecm) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle IS driven at a low speed increasing the risk of a crash.
Remedy
Dealers will reprogram the ecm free of charge. certain my 2006 altimas which have been previously remedied under recall campaign 06v223 (nissan r0606) are not included in this recall since the reprogramming for 06v223 also included this reprogramming. the recall began on december 31, 2007. owners may contact nissan at 1-800-647-7261.
Certain tyc halogen type headlamp assemblies p/n 20-6644-00 sold as aftermarket equipment for 2005-2006 nissan altima passenger vehicles. the photometric were misaligned which does not comply with federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment.
Risk and remedy
Risk
Misalignment of the lights diminishes frontal illumination which could result in a vehicle crash.
Remedy
Genera will notify owners and offer to repurchase the noncompliant lamps. the recall began on october 25, 2007. owners can contact genera at 714-522-6688.
Certain passenger vehicles equipped with 2.5L engines may experience excessive engine oil consumption as a result of improper performance of the piston rings.
Risk and remedy
Risk
If the oil IS not maintained at least at the minimum level, engine damage can occur and in extreme cases result in an engine fire.
Remedy
Dealers will reprogram the electronic control module (ecm or engine computer). your vehicle will also be inspected to determine if it has been consuming engine oil at a higher than normal rate. in a small percentage of vehicles, engine replacement will be needed. on june 9, 2006, nissan notified owners of the possibility of excessive oil consumption and the importance of maintaining the oil at a proper level. follow-up letter to owners advising them of the status of the recall was sent during august 2006. followup letter to owners was sent on november 15, 2006. owners may contact nissan at 1-800-647-7261.
On certain vehicles, the rear subframe may have been manufactured incorrectly, which could result in a crack in a bracket which holds part of the rear suspension.
Risk and remedy
Risk
If the bracket IS cracked, the stability of the vehicle may be affected under severe driving conditions. this could lead to a loss of control of the vehicle which could result in a crash.
Remedy
Dealers will inspect the rear subframe to determine if it was manufactured incorrectly and replace it, if necessary. the recall began on february 27, 2006. owners may contact nissan at 1-800-647-7261.
Owner complaints
824 complaints43 involved a crash14 involved a fire52 injuries
What owners report most
Latest complaints
- Service brakes, hydraulic
The contact owns a 2006 Nissan Altima. The contact stated that since owning the vehicle, the brakes, brake pads, or brake rotors were replaced every year to a year and a half. The contact became aware of the failure while depressing the brake pedal with an abnormal, grinding sound coming from the…
The contact owns a 2006 Nissan Altima. The contact stated that since owning the vehicle, the brakes, brake pads, or brake rotors were replaced every year to a year and a half. The contact became aware of the failure while depressing the brake pedal with an abnormal, grinding sound coming from the vehicle. There was no warning light illuminated. The vehicle was initially serviced at a dealer; however, due to the recurring brake failure, the contact suspected that the dealer might have intentionally caused the frequent brake failure. The vehicle was taken to an independent mechanic once the failure returned; however, the vehicle experienced the same failure. The manufacturer was notified of the failure but offered no assistance. The vehicle was not repaired. The failure mileage was approximately 10,000.
- Electrical system · Engine · Fuel/propulsion system
I have replaced the water pump, the belt, the thermostats, the rotors, the brakes, the fuel pump, the evap vent valve solenoid, the spark plugs, and fuel injectors and my car is STILL throwing the codes P-0462 and P-447. I've checked the wires and they are good. My car keeps misfiring and stalling…
I have replaced the water pump, the belt, the thermostats, the rotors, the brakes, the fuel pump, the evap vent valve solenoid, the spark plugs, and fuel injectors and my car is STILL throwing the codes P-0462 and P-447. I've checked the wires and they are good. My car keeps misfiring and stalling now and my fuel pump doesn't have a fuel level sensor. The float bar is brand new as well as the fuel pump. And my dashboard speedometer is 10 miles off. I've tried everything and it's still throwing the same codes.
- Power train · Suspension · Vehicle speed control
Cvtc transmission stalls almost got my kids and my pregnant daughter hit I bought the car only 2 months ago
- Air bags
Me and my fiancé had just picked the kids up from my mom’s. Got about 2 miles down the road and all of a sudden i heard a loud boom and a flash of light like a shot gun had went off in my ear. When I heard the boom my left side from my face to my hip felt like I had been hit. At the same time it…
Me and my fiancé had just picked the kids up from my mom’s. Got about 2 miles down the road and all of a sudden i heard a loud boom and a flash of light like a shot gun had went off in my ear. When I heard the boom my left side from my face to my hip felt like I had been hit. At the same time it happen with me it happen on the passenger side where my fiancé was sitting. I was able To pull to the side of the rd. I got out call law enforcement and looked around my car and it had not been hit so I open my door to get my kids out and that’s when I seen it was the airbags . They exploded and the reason I didn’t notice them when I got out of the car is because they was not inflated they had exploded. There is a huge hole in the top of each side air bag, it busted the inside of my passenger side door and threw shrapnel over to my driver side dash. He and I both are hurting on the side the airbags went off and he has a artificial hip on the side it hit him so I’m hoping it didn’t do anything to his hip
- Fuel/propulsion system
The fuel gauge stopped working. Fuel gauge shows full all the time. Error code is P0462. Mechanic replaced fuel pump module assembly and this did not fix the problem. Check engine light is on and will not go off and the code will not clear.
- Engine
The contact owns a 2006 Nissan Altima. The contact stated that while driving approximately 65 - 70 MPH, the vehicle began emitting white smoke coming from the rear end of the vehicle. The contact pulled to the side of the road and allowed the vehicle to cool off and added oil to the engine and the…
The contact owns a 2006 Nissan Altima. The contact stated that while driving approximately 65 - 70 MPH, the vehicle began emitting white smoke coming from the rear end of the vehicle. The contact pulled to the side of the road and allowed the vehicle to cool off and added oil to the engine and the smoke subsided. The contact became aware of oil around the bumper of the vehicle. The contact was able to continue to drive the vehicle however, oil had to be added often for the vehicle to operate as intended. The dealer was contacted to schedule an appointment however, the vehicle had not been taken to the dealer. The dealer confirmed there was no recall or warranty coverage on the vehicle. The vehicle had not been repaired. The manufacturer was made aware of the failure. The failure mileage was 105,000.
- Electrical system · Power train · Vehicle speed control
I started my vehicle, as usual, and when driving at a very slow speed (neighborhood speed limits) I approached a very busy intersection and the car just stopped. Not only did it stop, it would not steer and a bunch of warning lights came on the dashboard. Tav I believe, oil, check engine light.…
I started my vehicle, as usual, and when driving at a very slow speed (neighborhood speed limits) I approached a very busy intersection and the car just stopped. Not only did it stop, it would not steer and a bunch of warning lights came on the dashboard. Tav I believe, oil, check engine light. Even with the key in the acc mode, the power steering was not functioning. Everything just stopped functioning. I know this vehicle was recalled for the same exact thing back in 2008, but obviously it wasn't permanently fixed. Recall #07v-527. If I would have been in the middle of an intersection and this happened I could have been killed.
- Engine and engine cooling › Engine › Crank/camshaft position sensor
The contact owns a 2006 Nissan Altima. The contact stated that while driving at an undisclosed speed, the vehicle decelerated while the accelerator pedal was depressed at approximately 30 MPH. The check engine warning light illuminated. The contact stated that the vehicle was taken to an…
The contact owns a 2006 Nissan Altima. The contact stated that while driving at an undisclosed speed, the vehicle decelerated while the accelerator pedal was depressed at approximately 30 MPH. The check engine warning light illuminated. The contact stated that the vehicle was taken to an independent mechanic where the crankshaft position sensor and the camshaft were replaced; however, the failure recurred. The vehicle was taken to the dealer where the contact was informed by the dealer that there was no assistance available. The contact was not made aware of the diagnosis. The contact was informed by the dealer of NHTSA Campaign Number: 07V527000 (Engine and Engine Cooling). The vehicle was not repaired. The manufacturer was notified of the failure and the contact was provided a case number. The failure mileage was approximately 209,000. The VIN was unavailable.
- Air bags
The contact owned a 2006 Nissan Altima. The contact stated while exiting the highway, the contact lost control of the vehicle and struck a tree, causing several damages to the front of the vehicle. The air bags did not deploy, causing several injuries to the contact's right eye, cuts, and bruises…
The contact owned a 2006 Nissan Altima. The contact stated while exiting the highway, the contact lost control of the vehicle and struck a tree, causing several damages to the front of the vehicle. The air bags did not deploy, causing several injuries to the contact's right eye, cuts, and bruises to the left side of the contact's body. The contact sought medical attention. A police report was filed. The vehicle was towed and deemed a total loss by the insurance company. The manufacturer was not notified of the failure. The failure mileage was 210,000.
- Engine · Steering
The contact owns a 2006 Nissan Altima. The contact stated that while his sister was driving at an undisclosed speed, the steering wheel was shaking, and the vehicle stalled. The contact's sister turned off the vehicle. Additionally, the contact stated that after refueling, multiple attempts were…
The contact owns a 2006 Nissan Altima. The contact stated that while his sister was driving at an undisclosed speed, the steering wheel was shaking, and the vehicle stalled. The contact's sister turned off the vehicle. Additionally, the contact stated that after refueling, multiple attempts were needed to restart the vehicle. The check engine warning light was illuminated. The vehicle was taken to a local dealer; however, the failure could not be duplicated. The contact stated that an oil change was completed. The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 200,000.
- Electrical system · Engine
The crankshaft or camshaft sensor has went out which causes it to stall or immediately die, which is a safety hazard yes the check engine light was on
- Engine · Engine and engine cooling
The contact owns a 2006 Nissan Altima. The contact stated while driving 55 MPH, the vehicle lost motive power and stalled. There was no warning light illuminated. The contact was able to veer to the side of the road. The vehicle failed to restart and was towed to the residence of the contact's…
The contact owns a 2006 Nissan Altima. The contact stated while driving 55 MPH, the vehicle lost motive power and stalled. There was no warning light illuminated. The contact was able to veer to the side of the road. The vehicle failed to restart and was towed to the residence of the contact's friend. The dealer was notified of the failure and informed the contact there was no record that the vehicle was previously repaired under a recall related to the failure. The manufacturer was notified of the failure and informed the contact that they could not assist as the VIN was not included in NHTSA Campaign Number: 07V527000 (Engine and Engine Cooling). The vehicle was not diagnosed nor repaired. The failure mileage was approximately 217,636.
- Engine and engine cooling
The contact owns a 2006 Nissan Altima. The contact stated while driving approximately 35 MPH, abnormal amounts of smoke was coming from the exhaust tip. The contact stated that she had to add more oil to the vehicle every week. The contact stated that she had not noticed any oil spots on the…
The contact owns a 2006 Nissan Altima. The contact stated while driving approximately 35 MPH, abnormal amounts of smoke was coming from the exhaust tip. The contact stated that she had to add more oil to the vehicle every week. The contact stated that she had not noticed any oil spots on the driveway. The contact stated that the check engine warning light illuminated and remained illuminated. The contact had not taken the vehicle to a local dealer. The vehicle had not been diagnosed nor repaired. The contact had researched online and related the failure to NHTSA Campaign Number: 06V223000 (Engine and Engine Cooling). The manufacturer had not been informed of the failure. The failure mileage was approximately 175,000.
- Engine · Fuel/propulsion system · Steering
Vehicle is experiencing excessive oil consumption. I had to replace rack and pinion steering and vehicle is using excessive amounts of power steering fluid. I purchased both headlight assemblies due to not being able to align properly.
- Electrical system · Engine · Fuel/propulsion system
The car won't start
- Power train › Automatic transmission
The contact owns a 2006 Nissan Altima. The contact stated that the vehicle stalled upon the depression of the accelerator after coming to a complete stop. The contact was uncertain if any warning lights appeared during the failure. The contact was able to pull the vehicle off the road and into the…
The contact owns a 2006 Nissan Altima. The contact stated that the vehicle stalled upon the depression of the accelerator after coming to a complete stop. The contact was uncertain if any warning lights appeared during the failure. The contact was able to pull the vehicle off the road and into the entrance of a parking lot. She then stated that the vehicle independently lurched forward through a fence and rolled down a hill and into a five-lane road. The air bags did not deploy during the incident. A police report was not filed and the contact was injured. With the assistance of a fellow motorist, the contact was able to move the vehicle to a nearby independent mechanic. The mechanic attempted to jumpstart the vehicle but the vehicle failed to start up. The manufacturer was notified of the failure and was given a case number. The contact also spoke with three dealers (Dealers unknown) and they each offered no assistance. The vehicle had yet to be repaired and remained in the possession of the mechanic. The failure mileage was approximately 137,000
- Air bags
Hydroplaned while entering a toll Plaza on 9/22/2021. Crashed into the cement jersey wall and guardrail. Car was totaled with front end, driver's side, and driver's side rear-end damage. Airbags did not deploy. The vehicle is being housed at a tow lot and will be available for inspection until…
Hydroplaned while entering a toll Plaza on 9/22/2021. Crashed into the cement jersey wall and guardrail. Car was totaled with front end, driver's side, and driver's side rear-end damage. Airbags did not deploy. The vehicle is being housed at a tow lot and will be available for inspection until I receive a duplicate copy of my title from DMV. My safety was put at risk due to the fact the airbags did not deploy upon front-end impact. The vehicle was towed directly to the tow lot from the crash scene and the issue has not been reproduced or confirmed by a dealer or service center. The vehicle has only been inspected on scene by highway patrol, police, and tow company representatives. There were no prior warnings, messages, or symptoms of the problem prior to the failure. The only warning lamp illuminated at the time of incident was the service engine soon light.
- Electrical system · Engine · Steering
Last year i had the same issues with my 2003 nissan sentra gxe that i am now facing with my 2006 nissan altima. The serpentine belt comes off because of the harmonic balance and this ones ac clutch locked up and is wobbling plus my transmission acts irratic snd the starter csused the cwr to stall…
Last year i had the same issues with my 2003 nissan sentra gxe that i am now facing with my 2006 nissan altima. The serpentine belt comes off because of the harmonic balance and this ones ac clutch locked up and is wobbling plus my transmission acts irratic snd the starter csused the cwr to stall and catch fire! Th3 stress and agony of dpending all my savings fixing the car to end up stuck anyways and this is ongoing problems that keep reoccuring in all piece of sh** nissans and they want more money id like to file a lawsuit ! #BOYCOTT NISSAN
- Electrical system · Power train
UNKNOWN: While driving the car will stall. After restarting it, the car will then be stuck in fifth (highest) gear. The SES (Service engine soon) light comes on. The first time this happened, after the next trip, the SES light went out. Then the same thing happened. This is a danger because if this happens in heavy traffic, it could lead to a collision.
- Structure › Body · Unknown or other
When I lift my car (nissan altima 2006 ) at the mechanic to do repair job , I discovered a huge rust hole at the driver and passenger site at the front of the car , I shocked , it IS a safety concern , for me and for my family . The rust IS deep , wide and penetrating , my mechanic advice me to…
When I lift my car (nissan altima 2006 ) at the mechanic to do repair job , I discovered a huge rust hole at the driver and passenger site at the front of the car , I shocked , it IS a safety concern , for me and for my family . The rust IS deep , wide and penetrating , my mechanic advice me to sell it of any price but I dont want to sell it for any one , because I have a faithful conscious , and morals , I beileve in karma , I would not do it for any body , even the car has only 71,600 miles , I dont drive it alot , but from now on , I am not willing to drive it at all , or let mt daughters get in this car for a very serious safty concerns , a huge rust in the floor .
- Steering
TL* the contact owns a 2006 nissan altima. The contact stated that while driving out of the driveway and making a left turn, the steering wheel turned 360 degrees. The check engine light illuminated. The vehicle was taken to an independent mechanic who diagnosed the vehicle and determined that the…
TL* the contact owns a 2006 nissan altima. The contact stated that while driving out of the driveway and making a left turn, the steering wheel turned 360 degrees. The check engine light illuminated. The vehicle was taken to an independent mechanic who diagnosed the vehicle and determined that the steering column failed and needed to be replaced. The mechanic informed the contact that if she continued to drive the vehicle, the steering wheel may seize and cause the brakes to fail as well. The contact then contacted the manufacturer but was informed that the vehicle was over the warranty coverage and offered no assistance. The failure mileage was 130,000.
- Electrical system
My vehicle's check engine light came on one day so I took it to a mechanic and they said it was the crankshaft sensor so they replaced it. Then right after I left my light came back on and I took it to the mechanic again and he said it was the same code for the crankshaft sensor. After checking it…
My vehicle's check engine light came on one day so I took it to a mechanic and they said it was the crankshaft sensor so they replaced it. Then right after I left my light came back on and I took it to the mechanic again and he said it was the same code for the crankshaft sensor. After checking it again the mechanic said there IS some sort of eletrical problem there because it tells him to"check circuits" but even after messing around with the circuits my light IS still on.
- Fuel/propulsion system
The gas gauge isn't accurate therefore I dont know when im almost out of gas which caused my car to just cut of in the middle of traffic
- Air bags
TL* the contact owned a 2006 nissan altima. The contact stated while his wife was driving at 45 mph and attempting to make a left turn, when another vehicle crashed the front driver side bumper. Air bags did not deploy. The driver sustained facial laceration, fractured right shoulder and bruises…
TL* the contact owned a 2006 nissan altima. The contact stated while his wife was driving at 45 mph and attempting to make a left turn, when another vehicle crashed the front driver side bumper. Air bags did not deploy. The driver sustained facial laceration, fractured right shoulder and bruises on both thighs and the contact was the front passenger side sustained injuries on his right knee and but his head and left leg was also cut with broken window glass. The contact stated they were taken to the hospital to seek medical attention and his wife had surgery at a later time on her face and right shoulder. The vehicle was not driveable. The insurance adjuster deemed the vehicle was a total loss. A police report was filed. Upon investigation the contact associated the failure with manufacturer communication number: ntb-08-055-a, however the vin was not included. The manufacturer had been informed of failure. The failure mileage was approximately 122,649.
- Electrical system · Engine · Suspension
The rear suspension has always been an issue. While driving the wheel will scrape against the wheel well. You can't fit more the two people in the back seat due to this issue. The two front exterior headlights don't provide adequate lighting to even see the car in front of you. Its extremely…
The rear suspension has always been an issue. While driving the wheel will scrape against the wheel well. You can't fit more the two people in the back seat due to this issue. The two front exterior headlights don't provide adequate lighting to even see the car in front of you. Its extremely low/dense lighting even after changing out the bulbs. The electrical ignition switch to start the car has always been a problem. I have to turn the key, wait, turn it again, wait for the dashboard lights to come on, then finally the car will start. The power train gear control IS another waiting game. To put the car in drive, I first have to slowly shift though each gear before finally putting into drive. Once I do put it into drive the car will suddenly jolt forward before I'm able to start driving the car. I recently had the transmission replaced cause it just stopped while in motion and struggled to start up again. It finally did, but it couldn't drive over 1ST gear. I had to tow the car home. Also, few yrs back I had the head gasket replaced cause the car would shut off while I was driving. It would also not start up again if I had just turned off the engine. It needed time to cool off before restarting for me. And as of this moment, the car IS in the shop again. This time it needs a new engine. While it's idling, it's making a very loud clunking sound. It's just never ending with this car. I know there were many recalls on the engine, exterior lighting and rear suspension but I never got the notices.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11004962VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004961CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11004960CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001201WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001194REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001191WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10246452Expiration Notification - Maxima/Altima Floor Pan ***** Dealer Announcement ***** On October 28, 2022, in connection with the court-approved settlement of class action litigation filed in Missouri, Nissan launched a Voluntary Service Campaign (VSC) on 36,858 specific model year 2002-2006 Nissan Altima and 2004-2008 Nissan Maxima vehicles to inspect, and if necessary, repair for front floor pan corrosion. Per the terms of the settlement, the VSC expired on November 1, 2023. This Voluntary Service Campaign and customer reimbursement for these repairs will no longer be available after November 1, 2023. ***** What Dealers Should Do ***** 1. Service Comm will deactivate PC926 on any unrepaired VINs on November 1, 2023. No further dealer action is required.
- 10246436VOLUNTARY SERVICE CAMPAIGN 2002-2006 ALTIMA AND 2004-2008 MAXIMA; FLOOR PAN Voluntary Service Campaign ID # PC926 is no longer active. Repair orders opened after this bulletins published date are no longer eligible for reimbursement under Campaign ID # PC926. Discard all previous versions of NTB22-095.
- 10243708DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10239062SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
- 1023906012 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
- 10235710INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
- 10235707VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10233896ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232658REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232657WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232656WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232652DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10226127Maxima/Altima Floor Pan Voluntary Service Campaign ***** Dealer Announcement ***** Nissan is conducting a Voluntary Service Campaign (VSC) on 36,858 specific model year 2002-2006 Nissan Altima and 2004-2008 Nissan Maxima vehicles due to possibility of moisture becoming trapped in the floor pans potentially resulting in corrosion to support the settlement approved by the court presiding over a class action lawsuit filed in Missouri. Dealers will inspect the Class Vehicle for front floor pan corrosion. If corrosion is present the dealer will repair the front floor pan(s). Nissan is not responsible for unrelated repairs that may be needed or detected during the inspection, including for vehicle corrosion to areas other than the front floor pan. The class action settlement administrator will notify potential class members of approval of the settlement terms no later than November 30, 2022. Inspection for the front floor pan for corrosion must occur by November 1, 2023. Nissan will provide a one-time diagnosis and a potential repair of approved vehicles from October 31, 2022 to November 1, 2023 under the Voluntary Service Campaign.
- 10226126Voluntary service campaign 2002-2006 altima and 2004-2008 maxima floor pan pc926 will expire on november 1, 2023.
- 10226065Voluntary service campaign 2002-2006 altima and 2004-2008 maxima floor pan pc926 will expire on november 1, 2023.
- 10208946CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10206391STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10192805IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
- 10192801SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
- 10192727SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
- 10192677SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
- 10192638SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
- 10192632Nissan is conducting this voluntary Recall Campaign on certin Model 2006 Altima and Sentra vehicles to reprogram the ECM that emables a "limp home" mode if the engine oil drops below an acceptable level.
- 10192599SERVICE INFORMATION The Service Procedure provided in this bulletin is for the installation of Repair Plates on vehicles that have rust in the floor pan area. See this bulletin for further detail.
- 10192591SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
- 10192513SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
- 10192474SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
- 10192394SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
- 10192305SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
- 10192234Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
- 10192233Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
- 10192231SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
- 10192217If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
- 10192216SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
Every Nissan Altima model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.