2009 Toyota Camry Hybrid
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › Camry Hybrid › 2009
These records cover every 2009 Toyota Camry Hybrid. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2009 Toyota Camry Hybrid. Newest first.
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window…
Risk and remedy
Risk
If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy
Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013…
Risk and remedy
Risk
If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy
Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the…
Risk and remedy
Risk
If the switch overheats, it may melt, possibly resulting in a fire.
Remedy
Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Toyota IS recalling certain model year 2004-2010 passenger vehicles. the accelerator pedal can get stuck in the wide open position due to its being trapped by an unsecured or incompatible driver's floor mat.
Risk and remedy
Risk
A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death.
Remedy
Toyota filed an amended defect report on november 25, 2009, stating that dealers will modify the accelerator pedal and, on certain vehicles, alter the shape of the floor surface under the pedal. these changes address the risk of pedal entrapment due to interference with the floor mat. redesigned accelerator pedals will become available beginning in april 2010 and dealers will replace any modified pedal with the new pedal if desired. also, dealers will replace any genuine toyota or lexus all-weather floor mats with redesigned all-weather mats, or repurchase the previous mats from owners who do not want the new ones. additionally, software modifications will be installed on camry, avalon and lexus ES 350, IS 350 and IS 250 models that will ensure that the brake overrides the accelerator in the event both brake and accelerator pedals are applied. toyota will begin mailing letters to owners on december 31, 2009. owners may contact toyota at 1-800-331-4331, lexus at 1-800-255-3987.
Owner complaints
118 complaints10 involved a crash3 involved a fire4 injuries
What owners report most
Latest complaints
- Service brakes, hydraulic › Antilock/traction control/electronic limited slip › Abs warning light
The contact owns a 2009 Toyota Camry Hybrid. The contact’s wife stated while driving approximately 30 MPH, the VSC and ABS warning lights illuminated. The vehicle was taken to an independent mechanic and was diagnosed with needing the brake master cylinder replaced. The vehicle was not repaired.…
The contact owns a 2009 Toyota Camry Hybrid. The contact’s wife stated while driving approximately 30 MPH, the VSC and ABS warning lights illuminated. The vehicle was taken to an independent mechanic and was diagnosed with needing the brake master cylinder replaced. The vehicle was not repaired. The manufacturer was informed of the failure. The contact also filed a complaint with the manufacturer. The failure mileage was approximately 154,000.
- Seats › Front assembly › Seat heater/cooler
The contact owns a 2009 Toyota Camry Hybrid. The contact stated while driving 10 MPH, she smelled a burning odor and she saw smoke in the vehicle. The contact stated she also felt heat on her back. The contact stated as she continued to drive, the seat became increasingly warmer. There were no…
The contact owns a 2009 Toyota Camry Hybrid. The contact stated while driving 10 MPH, she smelled a burning odor and she saw smoke in the vehicle. The contact stated she also felt heat on her back. The contact stated as she continued to drive, the seat became increasingly warmer. There were no warning lights illuminated. The contact stated that she parked and exited the vehicle. The contact stated the seat then cooled down. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The contact stated that the failure had been reoccurring while driving and while the vehicle was parked. The dealer was notified of the failure and advised the contact that her VIN was not included in the recall for NHTSA Campaign Number: 16V396000 (SEATS). The manufacturer was notified of the failure and advised as the dealer. A case was opened. The vehicle was not diagnosed nor repaired. The approximate failure mileage was 168,000
- Service brakes, air › Antilock › Control unit/module
The contact owns a 2009 Toyota Camry Hybrid. The contact stated that while driving and depressing the brake pedal, the vehicle would not immediately stop, causing the stopping distance to become extended. The vehicle was taken to an independent mechanic who diagnosed that the ABS module was faulty…
The contact owns a 2009 Toyota Camry Hybrid. The contact stated that while driving and depressing the brake pedal, the vehicle would not immediately stop, causing the stopping distance to become extended. The vehicle was taken to an independent mechanic who diagnosed that the ABS module was faulty and needed to be replaced. The vehicle was not repaired. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The failure mileage was approximately 130,000.
- Service brakes
TL* the contact owns a 2009 toyota camry hybrid. The contact stated while operating the vehicle, the ABS, vsc, and check brake system warning lights illuminated and the vehicle would not immediately stop while depressing the brake pedal. The cause of the failure was not yet determined. The local dealer and manufacturer were not notified of the failure. The approximate failure mileage was 131,000.
- Structure › Body · Unknown or other
My dashboard IS melting, since it IS melting it IS causing the dashboard to be really shiney, which IS causing a huge reflection on my windshield, which IS making it hard to see out. The dashboard IS also really sticky from melting, and im also concerned about the airbags because of this.
- Structure
Re: tsb-l-sb-0144-11 sticky/melting dashboard the car IS 6 months beyond the date of the warranty enhancement period. Since the condition of shiny stickiness of the dashboard did not come to my attention until after the enhancement period, I believe that I am nevertheless entitled to the repair…
Re: tsb-l-sb-0144-11 sticky/melting dashboard the car IS 6 months beyond the date of the warranty enhancement period. Since the condition of shiny stickiness of the dashboard did not come to my attention until after the enhancement period, I believe that I am nevertheless entitled to the repair of the dashboard by toyota and that coverage should be also extended to the replacement of certain ancillary parts related to the replacement that might be damaged as a result of the warranty repair. There IS no valid reason that the warranty enhancement should have expired as this condition IS dangerous and needs to be corrected on all affected vehicles regardless of an arbitrary period set by toyota. *js
- Visibility/wiper
Melting dashboard and driver's side visor does not stay up. The melting dash causes a glare on the windshield causing visibility to be obstucted. I was told that I missed the warranty period but have never been sent anything about this problem.
- Service brakes
TL* the contact owns a 2009 toyota camry hybrid. While driving 45 mph and depressing the brake pedal, the vehicle failed to stop. The contact shifted into low gear and was able to coast the vehicle to the side of the road. In addition, the ABS, traction control, and brake warning indicators…
TL* the contact owns a 2009 toyota camry hybrid. While driving 45 mph and depressing the brake pedal, the vehicle failed to stop. The contact shifted into low gear and was able to coast the vehicle to the side of the road. In addition, the ABS, traction control, and brake warning indicators illuminated. The vehicle was towed to the contact's residence. The vehicle was not taken to a dealer or an independent mechanic for diagnostic testing. The vehicle was not repaired. The manufacturer was notified of the failure and did not assist. The approximate failure mileage was 137,000.
- Electronic stability control (esc) · Unknown or other
ABS and traction control are on the vehicle slips when taking of the vcs stability IS on it's very scary to drive the vehicle.
- Structure › Body
The rubber button to open the trunk melted, down to the rear bumper of my car (black).
- Electronic stability control (esc) · Service brakes
The hand brake light keeps coming on and off while driving. The car feels like it's coasting and have no traction control. All of the sudden, all lights turn on dashboard and check vsc system comes on, brakes are hard to engage and steering control IS difficult. Car drives like that for about 5…
The hand brake light keeps coming on and off while driving. The car feels like it's coasting and have no traction control. All of the sudden, all lights turn on dashboard and check vsc system comes on, brakes are hard to engage and steering control IS difficult. Car drives like that for about 5 minutes and then all goes back to normal. Few days later it starts up again with the break lights coming on and off. It happens during different driving conditions: straight city street, while turning, going down a hill or attempting to come to a stop. This makes it really scary as I am in a very dangerous situation when I am trying to break and the break do not engage and steering control IS affected. I have taken it to mechanic after the incidents and they cannot diagnose the issue and there are no failure codes. However, the issue keeps going on making me terrified to drive the car.
- Electronic stability control (esc)
My vsc light IS on along with the ABS and the brake light. While taking a 1 1/2 hour tript the light went off and stayed off for a few days. While taking another highway trip traveling the speed limit, the light was off until after driving for two hours I stopped at a restaurant. The lights came back on, and have been on ever since.
- Unknown or other
Vsc system keeping appearing on the dash board
- Service brakes
On my 2009 camry hybrid, as I was going to work, when I tried to slow down the car the brakes went hard and can't stop the car totally I saw the brake light, traction control, and ABS lights turned on, and check vsc system displayed. I immediately slow down the car took the exit and stop the car.…
On my 2009 camry hybrid, as I was going to work, when I tried to slow down the car the brakes went hard and can't stop the car totally I saw the brake light, traction control, and ABS lights turned on, and check vsc system displayed. I immediately slow down the car took the exit and stop the car. I turned off the car and start the car again which fixed all the above issues. it happened approx two weeks ago and took the car to toyota of grapevine tx 76051 and they did not find any issue related to brake or any code. I am scared to drive the car and taking the car to the same dealer to check again.
- Electrical system · Electronic stability control (esc) · Service brakes
I was driving on the interstate (395N into dc) and the car's brakes failed. The car immediately displayed vehicle control system (vcs) failure and a number of other warnings. I was forced to swerve out of traffic and to utilize the emergency brake to stop the car.
- Service brakes
Brake comes on, ABS light comes on and it becomes difficult to brake (brakes are hard). then after an hour or so the lights go off and brakes return to normal. I noticed that when it returns to normal there IS a heavy bump, it actually feels like someone bumped you from the rear. this has…
Brake comes on, ABS light comes on and it becomes difficult to brake (brakes are hard). then after an hour or so the lights go off and brakes return to normal. I noticed that when it returns to normal there IS a heavy bump, it actually feels like someone bumped you from the rear. this has happened off and on for about 3 months now. I took it to my mechanic thinking it was something minor, pads etc. And it was not that. on 11/28/18 I took it to the dealership. they found nothing wrong. not sure what else can be done. this IS very frustrating and potentially dangerous. because this problem can happen at any time with no warning, it has happened while driving and also starting the vehicle. my personal mechanic did find some information that may pertain to this problem (warranty enhancement program - ZE1 2007 - 2011 model year camry hybrid vehicles extension of warranty coverage for brake actuator assembly and skid control ecu/break pedal sensor) service campaign bulletin ref# t-cp-ze1, date of issue july 1, 2014.
- Electronic stability control (esc) · Service brakes
When I driving back yesterday jan 1ST 2019 from friends house suddenly the check vsc system turned on and other icons turned on in the car dashboard. I tried to press the brakes at a stop sign and they do not engage or they would engage on a delay, vehicle took long time to stop. It was hard…
When I driving back yesterday jan 1ST 2019 from friends house suddenly the check vsc system turned on and other icons turned on in the car dashboard. I tried to press the brakes at a stop sign and they do not engage or they would engage on a delay, vehicle took long time to stop. It was hard driving back and I was scared of an accident happening even after turning on emergency blinkers on my drive back home. Toyota needs to investigate it as it IS a safety issue.
- Service brakes
TL* the contact owns a 2009 toyota camry hybrid. While driving approximatey 10 mph and attempting to stop, the vehicle would not stop or slow down when depressing the brake pedal. During the failure, several warning messages and indicators displayed and illuminated including "check vsc system"…
TL* the contact owns a 2009 toyota camry hybrid. While driving approximatey 10 mph and attempting to stop, the vehicle would not stop or slow down when depressing the brake pedal. During the failure, several warning messages and indicators displayed and illuminated including "check vsc system" (vehicle stability control), ABS, master warning, and brake failure. When the contact turned off and restarted the vehicle, it operated normally. The vehicle was taken to passport toyota (5001 auth way, suitland, md) to be diagnosed, but the failure could not be duplicated. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 106,571.
- Service brakes
While driving straight at about 40 mph (in a 50 mph zone on a back road) I stepped on the brakes when approaching a stop sign. The brakes failed to engage. The check vbs system warning came on as well as all of the dash board warning lights. The car was checked and the brake pads were fine, the…
While driving straight at about 40 mph (in a 50 mph zone on a back road) I stepped on the brakes when approaching a stop sign. The brakes failed to engage. The check vbs system warning came on as well as all of the dash board warning lights. The car was checked and the brake pads were fine, the brake fluid level was normal, and no computer codes came up when that was checked. The brake light keeps coming on and off and the brakes work most of the time, but out of no where they won't engage. It was very scary, especially because my kids were in the car. Thank goodness I wasn't going faster than I was because I don't think we would have stopped in time.
- Electronic stability control (esc) · Service brakes
Brake, ABS and warning lights came on, check vsc message came on and my brakes stopped working. I was leaving my parking lot and got halfway down the block when this occurred. I could not brake so I let the car roll to a stop and used the curb to make a complete stop. Car I had not moved since I drove it really slow to house.
- Visibility/wiper
While I was driving at about 65 mph on a four lane divided highway, the driver's visor suddenly and unexpectedly rotated completely down, blocking my view out of the windshield so that I could not see ahead. It was a dangerous and frightening situation! I had to keep control of the car while…
While I was driving at about 65 mph on a four lane divided highway, the driver's visor suddenly and unexpectedly rotated completely down, blocking my view out of the windshield so that I could not see ahead. It was a dangerous and frightening situation! I had to keep control of the car while holding the visor up so that I could get home safely and then get the car to the repair facility. toyota knew that this safety hazard existed and was serious because it did a "warranty enhancement notice" for 2007 to 2011 camry hybrid sun visor brackets, but this expired for my car in may of 2016.
- Service brakes, hydraulic › Antilock/traction control/electronic limited slip · Service brakes, hydraulic › Antilock/traction control/electronic limited slip › Abs warning light
TL* the contact owns a 2009 toyota camry hybrid. While driving approximately 30 mph, the ABS warning indicator illuminated. The vehicle was taken to the dealer (autocentro toyota in san juan, puerto rico, 787-999-9115) where it was determined that the vehicle had a leak in the ABS. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 165,000.
- Visibility
Driver side sun visor falls down unexpectedly. will not stay in place except for full down position. this has been since the car was new. was searching for how to fix it and found link to here. I understand that this IS a common problem with all toyota visors and IS due to bad design and poor materials. toyota does not stand behind it and the replacement visors are the same junk as original.
- Visibility/wiper
My dashboard IS melting. When it solidifies it becomes extremely reflective and obstructs the windshield view.
- Service brakes · Unknown or other
The check vsc system was displayed in my totoya camry 2009 hybrid, this morning. The warning, ABS, brakes, parking brake and skid control lights have turned on. From test driving the vehicle, it appears that the brakes seem less responsive.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Pedestrian alert sounds
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
- Brake Actuator malfunction
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of…
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.
- Power Window Master Switch Fire
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia…
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
- Power Window Master Switch Fire
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built…
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005119This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005061This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
- 10230369DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10230368DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10230367DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
- 10227920DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10227919DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10227918DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
- 10227916DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 10227915TI: TECHNICAL INSTRUCTIONS Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
- 10227914CSP: Customer Support Program ZKG ? Paint Repair Process
- 10227913DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 10227912DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 10220174TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
- 10220158DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
- 10213902TSB: This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger
- 10211828DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 10211827TI: Technical Instructions Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
- 10211826CSP: Customer Support Program ZKG - Paint Repair Process Operation Flow Chart
- 10207946POL: This consolidated Tire Warranty Guide contains the complete warranty terms for all brands of ground and spare tires currently in use by Toyota. This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.
Every Toyota Camry Hybrid model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.