2001 Dodge RAM 1500
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Dodge › RAM 1500 › 2001
These records cover every 2001 Dodge RAM 1500. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2001 Dodge RAM 1500. Newest first.
Certain replacement k&n fuel performance kits, p/nos. 57-1509, 57-1511, 57-1511-1, 57-1517, 57-1517-1, 57-1527, and 57-1530. also, a small percentage of these kits were sold under the mopar performance parts brand name (p/nos. P5007069 and p5007070). all kits were manufactured from april 20, 1999, through september 23, 2004. these assemblies were…
Risk and remedy
Risk
A jammed open throttle could cause unintended acceleration of the vehicle, possibly resulting in a crash or increased stoping distances when braking.
Remedy
K&n will provide owners with a free repair kit along with repair instructions. the recall began on april 20, 2006.
On certain 4X4 pickup trucks equipped with the snow plow preparation package, the tires supplied on some vehicles may have gross axle weight ratings that slightly exceed the maximum tire load capacity as defined in federal motor vehicle safety standard no. 120, "tire selection and rims for motor vehicles other than passenger cars."
Risk and remedy
Remedy
Dealers will provide replacement p245/75r16 tires to meet the load carrying capacity specified on the vehicle certification label and accommodate the addition of a commercially available snow plow and hardware. owner notification began on december 22, 2003. owners should contact daimlerchrysler at 1-800-992-1997.
Vehicle description: pickup trucks. sound deadener material inside the steering wheel could become detached from the cover and housing. note: the RAM pickup trucks were built at the warren assembly plant ("s" in the 11TH vin position) from may 16, 2000 through october 23, 2000; st. Louis north assembly plant ("j" in the 11TH vin position) from may…
Risk and remedy
Risk
When this occurs, the material could interfere with the clockspring ribbon and cause an open circuit. the driver air bag system will become disabled, and the air bag warning lamp will illuminate on the instrument panel.
Remedy
Dealers will replace the clockspring assembly. owner notification began june 18, 2001. also some 1997-200 model year vehicles that, according to warranty records, have had a suspect replacement clockspring installed, will also be included in this campaign. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler at 1-800-853-1403.
Owner complaints
1,112 complaints65 involved a crash35 involved a fire80 injuries1 deaths
What owners report most
Latest complaints
- Service brakes, hydraulic
The contact owned a 2001 Dodge Ram 1500. The contact stated that while exiting a parking lot and attempting to depress the brake pedal, the brake pedal floored, causing the contact to roll to a stop on the side of the road. The ABS and Brake Warning lights illuminated. The contact was able to drive…
The contact owned a 2001 Dodge Ram 1500. The contact stated that while exiting a parking lot and attempting to depress the brake pedal, the brake pedal floored, causing the contact to roll to a stop on the side of the road. The ABS and Brake Warning lights illuminated. The contact was able to drive at 2 MPH to their home. The vehicle was towed to the dealer, who diagnosed that the brake line had blown and replaced it where it had failed. Approximately 6 months later, the ABS and brake warning lights illuminated again. The contact inspected the vehicle and noticed no leaks. When restarting the vehicle, the warning lights were no longer illuminated. While driving at an unknown speed, the ABS and brake lights illuminated again. The vehicle was taken to Meineke Car Care Center to a certified mechanic. The following morning, the lights were not illuminated. The vehicle was returned to Meineke Car Care Center, who stated that it may have been a computer glitch causing the lights to illuminate, then turn off when the vehicle was restarted. The contact had the brakes replaced as routine maintenance; however, after doing so, while driving in the rain at approximately 25 mph and attempting to apply the brakes, the brakes failed, causing the vehicle to rear-end the vehicle in front. The air bags did not deploy. The contact did not sustain injuries or require medical attention. The contact assumed the other driver had injuries, but could not confirm. A police report was filed. The contact was able to drive at a slow speed to their home. The ABS and Brake lights were illuminated. The vehicle was towed back to Meineke Car Care Center, where it was diagnosed that the other brake line had blown. The front end and brake line, which had blown was repaired. After the vehicle had been repaired, when coming to a stoplight, the failure occurred again, causing the vehicle to crash a second time. There were no injuries, air bags did not deploy. A police report was filed. The contact drove the vehicle to Meineke Car Care Center, who was
- Electrical system · Unknown or other
While driving and operating the heater, unbeknowst to me leaves/pine needles had come in through the fresh air cowl vent and built up on the heater blower resistor resulting in a fire. This design in dangerous as the default for the air intake is open and allows debris to enter and drop directly…
While driving and operating the heater, unbeknowst to me leaves/pine needles had come in through the fresh air cowl vent and built up on the heater blower resistor resulting in a fire. This design in dangerous as the default for the air intake is open and allows debris to enter and drop directly into the fan and blower motor resistor. I've searched online and seen multiple reports of this issue. I have a video I can provide if contacted.
- Air bags
Passenger side airbag exploded while sitting in my yard.
- Electrical system · Engine · Power train
The headlights no matter what bulbs I buy are extremely dim making it unsafe to drive at night. Now truck will not start for some unknown reason. It tries to turn over but will not crank. The mileage flashes NO BUS. I was literally only getting at best 8 miles per gallon.
- Air bags · Unknown or other
2001 Dodge Ram Dashboard is an extreme safety hazard due to the cracking. I have owned this vehicle for 12 years and it's been garaged kept for 8 years. The dash started with a crack and then a hole was created when hitting a bump. Then I had a mechanic work on the heater, and the dash basically…
2001 Dodge Ram Dashboard is an extreme safety hazard due to the cracking. I have owned this vehicle for 12 years and it's been garaged kept for 8 years. The dash started with a crack and then a hole was created when hitting a bump. Then I had a mechanic work on the heater, and the dash basically disintegrated when moving it. The holes on this dashboard are absurd. A review of safety information identified others who reported this problem to NHTSA and many more complaints on online message boards. This dashboard creates a safety issue for all personnel in the vehicle in case of an accident since projectiles (pieces of the dash that crumble) will fly. Also, there are other components under the dash that could create additional problems (ie-heater core spraying hot antifreeze after an accident). This is completely absurd. Keep in mind, my vehicle has less than 80K miles and the dash is getting worse.
- Unknown or other
unknown, Is all I know that I was checking the code on my truck and left truck on all night went out to start truck and battery was dead I got a jump from a friend and it started fine. I let it run for @20-30 minutes then I and my wife went to Realo drug store about 3/4 of a mile from home to get…
unknown, Is all I know that I was checking the code on my truck and left truck on all night went out to start truck and battery was dead I got a jump from a friend and it started fine. I let it run for @20-30 minutes then I and my wife went to Realo drug store about 3/4 of a mile from home to get her meds. We pulled up and waiting and got the meds payed for and my wife said there is smoke coming from under the hood. The truck stopped running and I tried to start it back and it did not start. Started smoking more and more I told my wife to get out of the truck and she did the pharmacist came out and help push the truck away from the store. Started flaming up and I drove it to a safe place and finally got out of the truck wife was ok but I had smoke halation and had to go on rescue squad to ER they said along with smoke halation I had a burnt nose ,forehead and burnt throat. Please check about this. Thank you
- Steering · Structure › Body
Where the sway bar is bolted to the chassis has completely deteriorated causing sway bar to completely detach from both sides of the frame. This has caused it very difficult to steer and nearly impossible the more MPH the vehicle goes. I own another vehicle nearly exactly the same but a 1998 dodge…
Where the sway bar is bolted to the chassis has completely deteriorated causing sway bar to completely detach from both sides of the frame. This has caused it very difficult to steer and nearly impossible the more MPH the vehicle goes. I own another vehicle nearly exactly the same but a 1998 dodge ram 1500 vin number [XXX]. It to has the same exact problem. I believe that the quality of steel used in manufacturing the frame of these vehicles was not up to standards. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
- Fuel/propulsion system
Shavent had funds to take to a shop but was told that the wrong fuel lines are on the truck
- Steering › Rack and pinion
The contact owns a 2001 Dodge Ram 1500. The contact stated while driving 45 MPH, the contact was making a turn and heard a loud grinding noise coming from the vehicle. The contact pulled the vehicle to the side of the road and took the vehicle out of gear and heard the grinding sound again. The…
The contact owns a 2001 Dodge Ram 1500. The contact stated while driving 45 MPH, the contact was making a turn and heard a loud grinding noise coming from the vehicle. The contact pulled the vehicle to the side of the road and took the vehicle out of gear and heard the grinding sound again. The contact was able to continue to drive to the residence. The contact inspected the vehicle and noticed that the pinion nut was loosened and grinding into the rear axle. The local dealer was contacted and informed the contact the vehicle was not safe to drive. The vehicle was not diagnosed nor repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 220,000.
- Unknown or other
The dash has been cracking for years. It has now disintegrated into very small pieces. It has clogged up the air ducts. The small pieces have blown in my eyes, creating a driving safety hazard. Ample history and reporting of this matter has been filed. It is an extreme safety hazard. The responsibility is clearly a manufacturing defect.
- Unknown or other
2001 Dodge RAM has a severely deteriorated dashboard. It has been this way since 2004. I am concerned that pieces of the cracked and damaged dashboard could become dangerous projectiles in the event of a crash with airbag deployment. The damaged pieces on the truck’s dashboard are very sharp, so…
2001 Dodge RAM has a severely deteriorated dashboard. It has been this way since 2004. I am concerned that pieces of the cracked and damaged dashboard could become dangerous projectiles in the event of a crash with airbag deployment. The damaged pieces on the truck’s dashboard are very sharp, so they could cause serious injury if they broke loose and became a projectile in a crash. It is simply amazing that a recall has not been issued up to this date. We've waited so long for this to be resolved. A dangerous manufacturing flaw!
- Power train
There have been three times now in the last two years, six-eight months of which I never drove the vehicle due to being repaired. I was driving at about 60-70mph. At which time there were no odd or sudden noises, no warning at all when the trucks acceleration goes way up till I let of the gas…
There have been three times now in the last two years, six-eight months of which I never drove the vehicle due to being repaired. I was driving at about 60-70mph. At which time there were no odd or sudden noises, no warning at all when the trucks acceleration goes way up till I let of the gas pedal, go to pull over while two of the three times, my drive shaft is bouncing between the road and underneath the truck which could have bounced up into another vehicle's windshield, radiator or whatever and could have actually hurt or even killed someone. Thank God nothing like that ever happened. After inspecting the problem, in which all three cases, the transfer case has broken off part of the tailshaft of the transmission and once, even broke part of the transfer case to. After trying to look up the problem on line, the exact same problem seems to have happened to several people from several different states and even one same instance from the same small town that I'm in. All the same instances that I've seen have been from the same type of vehicle from the years of 1995-2001. It just seems like a wide spread problem to me
- Unknown or other
The dash in my 2001 dodge RAM has cracked and pieces and some break off and fly around the cab of my truck while in motion.. I have 13 grand children and some pieces fly in the back seat. Can anyone do anything about this at all before anyone gets hurt? Its not my fault that dodge bought cheap effective dash boards, please look in to this it would help a lot to get a replacment. Thank you
- Engine
TL* the contact owns a 2001 dodge RAM 1500. The contact stated while driving 55 mph, the vehicle stalled. There was no warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with the engine control unit needing to be replaced. The vehicle had been…
TL* the contact owns a 2001 dodge RAM 1500. The contact stated while driving 55 mph, the vehicle stalled. There was no warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with the engine control unit needing to be replaced. The vehicle had been repaired twice however, the failure still recurred. The manufacturer had not been informed of the failure. The failure mileage was approximately 198,000.
- Engine · Vehicle speed control
Several times while I have been driving on a highway or busy road and the engine gets to normal operating temperature, the engine stalls and shuts off. Then I have to maneuver it to the side of the road and let it cool off approximately 15 minutes and then it cranks back up and I can drive 5 minutes and it does the same thing again, very dangerous.
- Electrical system · Engine · Fuel/propulsion system
I turned the key to start the engine and as it started cranking smoke started coming out of the defroster and then fire started coming out the engine hood. Luckily I had a fire extinguisher handy and opened the hood and put out the fire. Wondered where the fire started so tried starting again and…
I turned the key to start the engine and as it started cranking smoke started coming out of the defroster and then fire started coming out the engine hood. Luckily I had a fire extinguisher handy and opened the hood and put out the fire. Wondered where the fire started so tried starting again and fire started immediately at the rear of the engine or on top of the bell housing. I also smelled fuel. The truck was next to my garage and had been driven a few days earlier. If I had not put out the fire my whole house could have burned down. I donated the truck to wheels 4 vets.
- Unknown or other
My 2001 dodge ran has a broken and cracked dash board parts of the dash will fly off and hit things,people ect and I think it will hurt the people I love like my grandkids,wife ect. I think it should be recalled because someone (driver) might get hit in the face and lose control of the vehicle and…
My 2001 dodge ran has a broken and cracked dash board parts of the dash will fly off and hit things,people ect and I think it will hurt the people I love like my grandkids,wife ect. I think it should be recalled because someone (driver) might get hit in the face and lose control of the vehicle and someone gets hurt or even killed from this cracked dashboard that IS not the owners fault. Thank you and please can you recall this dashboard?
- Power train
TL* the contact owns a 2001 dodge RAM 1500. The contact stated that the gear shifter was very loose and moved a lot when the vehicle was in motion. Also, the gear indicator displayed different gears even though the vehicle was in the drive position. The dealer and manufacturer were not contacted. The vehicle was not diagnosed or repaired. The failure mileage was 400,000. The vin was unknown.
- Structure › Body
TL* the contact owns a 2001 dodge RAM 1500. The contact stated that the dash board was disintegrating. Pieces of the dashboard were penetrating through the heater vacuum system, which caused the heater not to work. The manufacturer was contacted. The dealer was not contacted. The vehicle was not diagnosed or repaired. The failure mileage was 163,000.
- Structure › Body
Dash panel has cracked badly to the point pieces have fallen out exposing wires, connectors, ducts and other under-dash components. I am concerned this may affect inflation of air bags and potential for pieces of cracked dash to cause severe injury in the event of air bag deployment. dash panel…
Dash panel has cracked badly to the point pieces have fallen out exposing wires, connectors, ducts and other under-dash components. I am concerned this may affect inflation of air bags and potential for pieces of cracked dash to cause severe injury in the event of air bag deployment. dash panel cracking on these models IS well known to chrysler, and has drawn national media attention (eg new york times, 2013). chrysler has apparently refused to acknowledge its liability to repair this problem.
- Electrical system
Dashboard falling apart; sharp/jagged pieces of dash cutting into electrical wiring causing shorts, failure of electrical equipment on board truck; while driving on street, highways in motion straight-line and turning.
- Air bags · Steering · Unknown or other
I'm worried that the air bag on passenger side IS defective as the strangest noise IS coming from behind the dash like a rubber band IS tightening and then clicking on and off. Doesn't happen all the time. I've also had my truck in for the steering before and it has never been right. now the hood…
I'm worried that the air bag on passenger side IS defective as the strangest noise IS coming from behind the dash like a rubber band IS tightening and then clicking on and off. Doesn't happen all the time. I've also had my truck in for the steering before and it has never been right. now the hood will not shut right. it's always been a lemon. I fight to keep it on the road. it doesn't even have 36,000 miles on it. I'm wondering what recalls I've missed so I'm checking. thank you.
- Vehicle speed control
TL* the contact owns a 2001 dodge RAM 1500. While accelerating from a stop, the accelerator pedal suddenly became stuck and caused the vehicle to keep accelerating. The vehicle was immediately shut off, but the failure continued once it was restarted. The failure was not diagnosed or repaired. The…
TL* the contact owns a 2001 dodge RAM 1500. While accelerating from a stop, the accelerator pedal suddenly became stuck and caused the vehicle to keep accelerating. The vehicle was immediately shut off, but the failure continued once it was restarted. The failure was not diagnosed or repaired. The local dealer (victory dodge, 64 greensburg st, delmont, pa) was notified of the failure. The manufacturer was not notified. The vin was not available. The failure mileage was 60,000.
- Structure › Body
Disintegration of dashboard plastics. this IS a known problem for dodge trucks in this timeframe. if this vehicle were to be in an accident sufficient to deploy the airbags, sharp plastic shards would be propelled everywhere, including the face and eyes.
- Structure › Body
The hood latch behind the grill broke or failed. my hood flew up as I was driving down the road and shattered my windshield. The hood and hinges are bent. it felt like I hit a brick wall. I could not see anything. I gradually got to the side of the road. I could not pull the hood down. A…
The hood latch behind the grill broke or failed. my hood flew up as I was driving down the road and shattered my windshield. The hood and hinges are bent. it felt like I hit a brick wall. I could not see anything. I gradually got to the side of the road. I could not pull the hood down. A gentleman stopped to help me and we got the hood down but it would not close. The hood had to be secured with a bungee cord. my truck was towed and IS currently in the shop. They will be replacing the hood, windshield and hood latch. this was a dangerous situation I was put in from a faulty hood latch.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- 2000-2001 dodge RAM pickup hood latch
The agency opened this investigation based on 30 complaints alleging that the hoods on model year (my) 2000 and 2001 dodge RAM pickup trucks flew up and blocked the driver's vision.these vehicles have a primary hood latch and a secondary (backup) hood latch.the secondary latch IS designed to secure the hood if the…
The agency opened this investigation based on 30 complaints alleging that the hoods on model year (my) 2000 and 2001 dodge RAM pickup trucks flew up and blocked the driver's vision.these vehicles have a primary hood latch and a secondary (backup) hood latch.the secondary latch IS designed to secure the hood if the primary hood latch IS not properly closed or otherwise malfunctions.in these complaints, the secondary hood latch malfunctioned, apparently due to corrosion, and did not latch.dodge conducted recall 01v-040 in 1999 to address similar problems on model year 1994-1997 dodge RAM pickup trucks.the information chrysler provided in response to odi's information request letter indicated that the my 2000 and 2001 vehicles were equipped with secondary hood latches with stainless steel return springs, as opposed to the earlier recalled trucks that had zinc coated carbon steel return springs.the recalled components were susceptible to corrosion-induced failure due to the type of material used, whereas the corrosion failures in the newer models appear to be due to lubrication loss over time (regular application of grease IS advised per instructions in the owners' manual). Odi's review of chrysler's warranty, complaint, and injury data for the 2000 and 2001 vehicles indicates that the rates for subject vehicles are low and are declining.a potential defect trend has not been identified.this investigation IS closed.
- Rear safety belt anchorage disengagement
Allege that both rear inboard safety belt anchorages were found to lack proper attachments.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10229256KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10224768Connecting to the DRB III Emulator for Cummins Engines
- 10223854Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
- 10221686KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10191460Valve Body. These may cause over drive cycling.
- 10191455Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only.
- 10176211This SKU is a Clock Spring. The customer communication requested return of unsold inventory to inspect the internal spring. If the internal spring is not seated, the electrical circuit for the horn is disconnected and the horn will not function. The horn electrical circuit does not affect the airbag circuit.
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10139596Part Description: Insulator on Lever Assy Manual Valve - Valve Body - RWD Transmission Issue Description: The manual valve insulator, attaching rivet and instruction sheet are now available as a kit. If the insulator requires replacement please order kit 68253161AA. Insulator only used on Auto-RWD transmission Note: The color of the insulator is not relevant for service.
- 10139595Part Description: Insulator in Lever Assembly - Valve Body - Trans Issue Description: The manual valve insulator, attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service
- 1013900968069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~
- 10136906Part Description: Seal - Shift Shaft on RFE transmissions Issue Description: This seal (04799346) is replaceable with Seal Kit (68235551AA), which includes a seal and retainer. The Seal Kit is applicable to all (5)45RFE transmissions.
- 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10011493Original minute mount wiring and e-force isolation module wiring conversions. Fisher. Various models including all gm/chevrolet and ford. 2002 & prior.
- 6092268Some short wheel base trucks built at the warren truck assembly plant may have been shipped with the wrong steering gear.
- 618878Some vehicles with a long wheel base RAM truck steering gear may have sensitive steering and exhibit a steering wander condition - advance service action.
- 610642Advance service information regarding the right brake caliper's bleeder screw located on bottom of caliper making it difficult to bleed the brakes.
Every Dodge RAM 1500 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.