2007 Hino Conventional Models

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11000898This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
• 11000897After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
• 10189453BOSTROM - LTSS (LIGHT TRUCK SUSPENSION SEAT) DESIGNED TO FIT THE HINO 155 & 195 COE ? Proven to reduce vibration to the occupant compared to the conventional static seat = LESS FATIGUE ? The suspension system can easily be adjusted to the weight of the driver
• 10189439Hino Trucks floor mats. Black durable rubber floor mats with the red Hino Trucks emblem. Easy to shake out the dirt and debris or clean it with soapy water.
• 10189422Floor mats sale for Hino Conventional (MY 2005-2017) & COE (My 2012-2017)
• 10185627When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 oil passage plugs, you will need to install them before proceeding
• 10185599In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating of the transmission fluid due to the torque converter clutch not functioning. A jumper harness has been made available that will allow operation of the torque converter clutch in the event that the vehicle is driven while the ABS warning lamp is illuminated.
• 10185585The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to use for servicing.
• 10184987Suspension - Air spring shield - Conventional Trucks equipped with a Comfort Ride rear air suspension.
• 101848632005-07 Conventional Light Duty Truck (LDT) with a J05E engine. During engine performance diagnostics, comparative readings from a like engine can be useful data points from a known good engine to use for comparisons (refer data in PDF documents).
• 10184813Fluid Leak from Allison Housing Breather in Cold Conditions at Startup. This bulletin provides the corrective action for a fluid overflow condition from the main housing breather at startup in cold ambient temperatures at or below +5f (-15c). 2005-2008 model year Hino Conventional trucks equipped with Allison 1000 or 2000 family series automatic transmissions.
• 10184170Hino Quick Reference Guide 2005-2010 Model Years
• 10184154ABS light on and Trans Shifts Erratically.
• 10182836Napschart
• 10182806This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be tested and replaced when necessary before replacing the supply pump assembly for a fuel pressure related concern.
• 10182802Complete Engine Assembly Part Numbers
• 10182787ECU File Downloading, Reprogramming and INF File Uploading via HinoNet
• 10182786Injector clamp bolt tightening torque and procedure
• 10182785Davco fuel filter change and priming procedure
• 10182783Racor and Davco - Fuel/Water Seperators
• 10182773The document is to inform the dealers about the design change in the aligning marks on the flywheel.
• 10182759Lock Assembly Kit (Keyed Alike)
• 10182755Rear Axle gear ratio change or change in tire size
• 10182745Introduction of Exchange Turbocharger Program
• 10182738The information applies to the installation of a customer supplied and commercially available Electric Trailer Brake Controller for all 2007-2008 Hino trucks.
• 10182727This document is to inform of the following information regarding the replacement and installation of the Aisin 450-43 LE Automatic Transmissions.
• 10182676This document is to inform of the procedure to calibrate the Pulse Adjust Module when needed (ex. tire size change, rear carrier ratio change) .
• 10182669Fuel diluting engine oil
• 10167193This design change of the idler gear case and idler gear bolt is to address the idler gear bolt loosening under abnormal loading from fuel supply pump and the gear train. The redesigned idler gear case and idler gear bolt are designed to increase their robustness and prevent the idler gear bolt from loosening.

Every Hino Conventional Models model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.