2015 Hino Conventional Models

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11000898This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
• 11000897After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
• 10235337The purpose of this procedure is to provide instructions in how to properly record Nox Sensors using DX3
• 10231442Conventional diesel particulate filter (dpf) aasw0
• 10231440Conventional nitrogen oxide (nox) sensor aapd0
• 10231439Recovering the doser control unit (dcu) after a failed programming event dcu blank. Tt-23-011
• 102289392011MY-2021MY CONVENTIONAL EXTERIOR MIRROR STAY. The subject vehicle may experience an exterior mirror stay that is loose or drifts slightly from its position. An enhanced mirror stay, mirror stay mount, related fasteners and revised torque specifications have been released to correct this condition. This procedure provides directions for installation of the enhanced components. Reports of looseness have accompanied reports that vehicle operators have folded exterior mirrors inward. As clearly stated in the Hino owners manual, the structure of the mirror stay does not allow for folding.
• 10227282The purpose of this procedure is to provide instructions in how to properly record NOx sensors using DX3.
• 10227281The purpose of this procedure is to provide instructions in performing an injection quantity test on 2011 and newer Conventional or COE series trucks with DX3.
• 10227279The purpose of this procedure is to provide instructions in performing DCU programming on 2011 and newer Conventional or COE series trucks.
• 10227276The purpose of this procedure is to provide instructions in how to perform a manual regen recording on Hino Trucks equipped with a 5th or 7th exhaust fuel injector with DX3.
• 10214940Conventional cab structure front mount repair
• 10213495Conventional after turbo catalyst (atc) aapa0. Wp-22-010
• 10209669Diesel nitrogen oxide (nox) sensor part number change tech tip tt-22-004
• 10206053SB-21-002 CONVENTIONAL FUEL SENDER LEAK. Certain vehicles may exhibit fuel residue accumulation around the fuel level sensor or cover plate in certain conditions, including if the vehicle is equipped with dual fuel tanks. Updated fuel level sensor bolt sealing washers have been made available to address this condition.
• 10189485Revive slip cover set for National Seating Cush-N-Aire & 2000 Series Seats. Contains both back & seat cushion covers. Made specifically to fit National Seats with 18? to 21? wide backs & 18? to 23? wide cushions.
• 10189453BOSTROM - LTSS (LIGHT TRUCK SUSPENSION SEAT) DESIGNED TO FIT THE HINO 155 & 195 COE ? Proven to reduce vibration to the occupant compared to the conventional static seat = LESS FATIGUE ? The suspension system can easily be adjusted to the weight of the driver
• 10189439Hino Trucks floor mats. Black durable rubber floor mats with the red Hino Trucks emblem. Easy to shake out the dirt and debris or clean it with soapy water.
• 10189426Hino reference guide for Conventional, MY2015-2017
• 10189424Hino COE Quick Reference Guide
• 10189422Floor mats sale for Hino Conventional (MY 2005-2017) & COE (My 2012-2017)
• 10185627When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 oil passage plugs, you will need to install them before proceeding
• 10185625The tech tip below is to reset the speedometer after a tire size change or rear end gear change.
• 10185624The following procedure is for resetting the engine hour meter display showing total running time, driving time, and idling time of the vehicle in minutes and seconds. Total shows the time from engine start to engine stop. Drive or Idle shows the time of total driving time and total engine idling time. When the hour meter reaches 999.9 it will stop. The display can be reset to 0 to continue tracking engine hours for maintenance purposes by following the procedure below.
• 10185622When replacing an audio unit for a CD player issue, the CD may not eject properly from the unit. DO NOT disassemble the audio unit to remove the CD. This will void any applicable warranty coverage for this repair. If the customer wishes to have the CD returned, please complete the following form indicating where the customer would like the CD shipped. Include this form with the warranty returned part.
• 10185621When diagnosing a concern with the SCR system, the technician may notice crystallized DEF (diesel exhaust fluid) on the tip of the DEF injector. Crystallized DEF on the tip of the injector is a normal occurrence and does not indicate that the injector nozzle is clogged. The crystallization will dissolve when the injector is activated. Do not replace the DEF injector for the crystallization alone. Please follow Workshop Manual diagnostics to diagnose the specific condition or DTC on the vehicle.
• 10185618Some 2013MY-2017MY COE units may illuminate the ABS light and store DTC C1425 after the aftermarket LED tail lamps are installed. In addition, the turn signals may flash quicker than normal and the cruise control will be disabled.
• 10185616The following information applies to the installation of a customer supplied and commercially available electric trailer brake controller for all 2012MY-2017 MY Hino trucks. This application only applies to brake controllers which operate using a 12-volt input signal from the chassis when the brakes are applied.
• 10185615The following information applies to the installation of a customer supplied and commercially available electric trailer brake controller for all 2008MY-2015MY Hino trucks. This application only applies to brake controllers which operate using a 12-volt input signal from the chassis when the brakes are applied.
• 10185613Bendix Air Dryer Service
• 10185610Some customer?s may request to enable to Idle Shutdown to save on fuel costs and Idling time. The procedure below will detail how to enable the Idle Shutdown timer.
• 10185602Correction of workshop manual for 2011 - 2015 my (revision of troubleshooting procedure for the dtc p2201 & p2214)
• 10185601The following is to inform you of the above caption. This service data should be attached to the relevant pages of the workshop manuals for maintenance and to use for servicing.
• 10185600When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
• 10185594A subject vehicle may exhibit an illuminated check engine lamp with DTC (Diagnostic Trouble Code) P0421 (Catalyst efficiency below threshold). The engine ECU may falsely detect an issue with the ATC (After Turbo Catalyst) with the current ECU software. If DTC P0421 is stored in the engine ECU, reprogram the ECU to the latest software level prior to suspecting a fault with the ATC.
• 10185593When viewing one of the subject vehicles from the front, while it is parked on level ground, the cab may appear to be leaning to the driver?s side. In the event that the cab is leaning to the driver?s side, a work procedure has been released to improve the leaning condition. The work procedure provides for correction of the lean by adding or subtracting shims from the front leaf springs. This procedure should only be performed prior to a body being installed on the vehicle. An improperly installed body may either create the illusion of a cab lean, or actually cause the cab to lean.
• 10185588A subject vehicle may exhibit an illuminated Malfunction Indicator Lamp (MIL) on and a code P1604 stored in the Transmission Control Module.
• 10185587The following procedure is for programming the keyless entry remote control(s) for trucks that are equipped with keyless entry system.
• 10185582The broken hood grille procedure (SB-14-020) has been revised to reuse the grille nuts (SZ17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised procedure has been posted on HinoNet. Please see the picture below on which area of the procedure has been updated.
• 10185581The DTC?s P2080 and P2084 and a MIL on, may be found on 15MY Conventional models. These diagnostic codes may be set due to a software detection anomaly that can occur under certain conditions. An ECU software update to address this condition has been released.

Every Hino Conventional Models model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.