2009 Hino Conventional Models

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11000898This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
• 11000897After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
• 10189453BOSTROM - LTSS (LIGHT TRUCK SUSPENSION SEAT) DESIGNED TO FIT THE HINO 155 & 195 COE ? Proven to reduce vibration to the occupant compared to the conventional static seat = LESS FATIGUE ? The suspension system can easily be adjusted to the weight of the driver
• 10189439Hino Trucks floor mats. Black durable rubber floor mats with the red Hino Trucks emblem. Easy to shake out the dirt and debris or clean it with soapy water.
• 10189422Floor mats sale for Hino Conventional (MY 2005-2017) & COE (My 2012-2017)
• 10185627When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 oil passage plugs, you will need to install them before proceeding
• 10185623A subject vehicle at 200,000 miles may exhibit a ?DPR Maintenance? message displayed on the Instrument Cluster message center. The following procedure will instruct how to check the DPF and reset the displayed message.
• 10185617This procedure illustrates a worst case scenario repair procedure, the process and materials being used are the same for all repairs. Depending on the location of the repair, access may be limited in some cases. Ensure that the repair area extends at least 2 inches on either side of the cracked area.
• 10185615The following information applies to the installation of a customer supplied and commercially available electric trailer brake controller for all 2008MY-2015MY Hino trucks. This application only applies to brake controllers which operate using a 12-volt input signal from the chassis when the brakes are applied.
• 10185607Exhaust Control Valve Adjustment Procedure
• 10185598In the event that one of the subject vehicles is driven while the ABS warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an ABS warning lamp illuminated can lead to overheating of the transmission fluid due to the torque converter clutch not functioning. A jumper harness has been made available that will allow operation of the torque converter clutch in the event that the vehicle is driven while the ABS warning lamp is illuminated.
• 10185585The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to use for servicing.
• 10184987Suspension - Air spring shield - Conventional Trucks equipped with a Comfort Ride rear air suspension.
• 10184984General - Brake switch low power diagnosis. Conventionnal Trucks or 2013 - 16 (155, 195) COE trucks. The purpose of the tech tip is to provide information for a low power concern possibly relating to the brake switch. Hino Trucks are equipped with two brake switches. First, a stop lamp switch that is designed to activate stop lamps on the truck. Second, a brakeswitch that is designed to send brake application input for modules to monitor brake activation. When monitoring DXII with the brake applied, the switches should both read ON and when the brake pedal is released, they shoiuld both read OFF. If the brake is not applied (typically when accelerating) and if one switch reads ON while the other reads OFF when the brake pedal is not applied, a brake switch correlation concern is the likely cause. Perform the following to identify the switch with this concern.
• 10184854176 Updated Speedkometer Conversion Rate Procedure. 2008-2010 model year conventional trucks. The Tech tip is to use with the updated cable and DX2 for changing the speedometer conversion rate. Please note that an updated cable can be provided through Tech Assist if it's returned once the repair has been completed.
• 10184848P2002 DPR System Malfunction (2-Digit Diagnosis Codes) In the event that DTC dP2002 - DPR ( Diesel Particulate Reduction) System Malfunction sets in the enginef ECU (ddsEngine Control Unit), additional diagnostic information is provided through the use of a 2 digit diagnosis code (DGCODE). This publication provides the definition for these double digit codes.
• 101848452008 - 2016 Headlamp Condensation or Water Intrusion. The customer may complain of water or condensation within the headlamp assembly. If the vehicle exhibits this condition, it is necessary to first verify that all of the protective covers and caps are installed before suspecting a problem with the headlamp assembly. Any loose of missing caps or cover s on the headlamp will result in water entry. Note that some condensation within the headlamp at times should be considered normal.
• 10184819New parts are available to prevent repeat exhaust manifold stud failures on the J05 engine. This bulletin provides instructions for an exhaust manifold attachment modification at the #1 and #4 cylinder locations. Modifications to the manifold insulator shield and the turbocharger water return pipe have also been made to accommodate the longer studs.
• 10184817Addition of the troubleshooting procedure for engine lacked power during the DPR automatic regeneration. Relevant Manuals: Hino 145, 165, 185, 238, 258, 268, 308 and 338
• 10184211Requirements of biofuel usage for 2008MY thru 2012MY vehicles.
• 10184175Lack of power and possible check engine light on.
• 10184173Some 2008-2010 North American Production vehicles may exhibit a bucking or a surge condition under heavy engine load or during DPR auto-regeneration.
• 10184170Hino Quick Reference Guide 2005-2010 Model Years
• 10184154ABS light on and Trans Shifts Erratically.
• 10182868Requirements of biofuel usage for 2008MY thru 2012MY vehicles.
• 10182836Napschart
• 10182806This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be tested and replaced when necessary before replacing the supply pump assembly for a fuel pressure related concern.
• 10182802Complete Engine Assembly Part Numbers
• 10182787ECU File Downloading, Reprogramming and INF File Uploading via HinoNet
• 10182786Injector clamp bolt tightening torque and procedure
• 10182785Davco fuel filter change and priming procedure
• 10182727This document is to inform of the following information regarding the replacement and installation of the Aisin 450-43 LE Automatic Transmissions.
• 10182676This document is to inform of the procedure to calibrate the Pulse Adjust Module when needed (ex. tire size change, rear carrier ratio change) .
• 10167193This design change of the idler gear case and idler gear bolt is to address the idler gear bolt loosening under abnormal loading from fuel supply pump and the gear train. The redesigned idler gear case and idler gear bolt are designed to increase their robustness and prevent the idler gear bolt from loosening.

Every Hino Conventional Models model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.