2012 Hino Conventional Models

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11000898This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
• 11000897After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
• 10235337The purpose of this procedure is to provide instructions in how to properly record Nox Sensors using DX3
• 10231442Conventional diesel particulate filter (dpf) aasw0
• 10231440Conventional nitrogen oxide (nox) sensor aapd0
• 10231436DX3 burner control unit (bcu) programming. Tt-23-008
• 102289392011MY-2021MY CONVENTIONAL EXTERIOR MIRROR STAY. The subject vehicle may experience an exterior mirror stay that is loose or drifts slightly from its position. An enhanced mirror stay, mirror stay mount, related fasteners and revised torque specifications have been released to correct this condition. This procedure provides directions for installation of the enhanced components. Reports of looseness have accompanied reports that vehicle operators have folded exterior mirrors inward. As clearly stated in the Hino owners manual, the structure of the mirror stay does not allow for folding.
• 10227282The purpose of this procedure is to provide instructions in how to properly record NOx sensors using DX3.
• 10227281The purpose of this procedure is to provide instructions in performing an injection quantity test on 2011 and newer Conventional or COE series trucks with DX3.
• 10227279The purpose of this procedure is to provide instructions in performing DCU programming on 2011 and newer Conventional or COE series trucks.
• 10227274The purpose of this procedure is to provide instructions in how to perform a burner regen recording on Conventional trucks equipped with a burner style exhaust system with DX3.
• 10214940Conventional cab structure front mount repair
• 10209669Diesel nitrogen oxide (nox) sensor part number change tech tip tt-22-004
• 10206053SB-21-002 CONVENTIONAL FUEL SENDER LEAK. Certain vehicles may exhibit fuel residue accumulation around the fuel level sensor or cover plate in certain conditions, including if the vehicle is equipped with dual fuel tanks. Updated fuel level sensor bolt sealing washers have been made available to address this condition.
• 10194731Deterioration of the fuel regulator piston seals due to high concentrations of biofuels or poor fuels may cause fuel to leak from the burner atomizer in the after treatment system.
• 10189730WARRANTY ENHANCEMENT PROGRAM CONVENTIONAL BURNER ATOMIZER. Deterioration of the fuel regulator piston seals due to high concentrations of biofuels or poor fuels may cause fuel to leak from the burner atomizer in the after treatment system.
• 10189485Revive slip cover set for National Seating Cush-N-Aire & 2000 Series Seats. Contains both back & seat cushion covers. Made specifically to fit National Seats with 18? to 21? wide backs & 18? to 23? wide cushions.
• 10189453BOSTROM - LTSS (LIGHT TRUCK SUSPENSION SEAT) DESIGNED TO FIT THE HINO 155 & 195 COE ? Proven to reduce vibration to the occupant compared to the conventional static seat = LESS FATIGUE ? The suspension system can easily be adjusted to the weight of the driver
• 10189439Hino Trucks floor mats. Black durable rubber floor mats with the red Hino Trucks emblem. Easy to shake out the dirt and debris or clean it with soapy water.
• 10189425Hino reference guide for Conventional, MY2011-2014
• 10189424Hino COE Quick Reference Guide
• 10189422Floor mats sale for Hino Conventional (MY 2005-2017) & COE (My 2012-2017)
• 10185627When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 oil passage plugs, you will need to install them before proceeding
• 10185626During diagnosis of the exhaust aftertreatment system, the technician may find that the combustion chamber igniter plugs are covered in soot or appear to be excessively worn. If the igniters are dirty or have some wear, this alone does not justify replacement. No service of the igniters is recommended unless an issue with the spark between them is confirmed during a spark test. If, during the spark test the arc between the igniters does not function properly, it is recommended to first clean the igniters, and then check the air gap using the following procedure prior to replacement of the igniters.
• 10185625The tech tip below is to reset the speedometer after a tire size change or rear end gear change.
• 10185624The following procedure is for resetting the engine hour meter display showing total running time, driving time, and idling time of the vehicle in minutes and seconds. Total shows the time from engine start to engine stop. Drive or Idle shows the time of total driving time and total engine idling time. When the hour meter reaches 999.9 it will stop. The display can be reset to 0 to continue tracking engine hours for maintenance purposes by following the procedure below.
• 10185622When replacing an audio unit for a CD player issue, the CD may not eject properly from the unit. DO NOT disassemble the audio unit to remove the CD. This will void any applicable warranty coverage for this repair. If the customer wishes to have the CD returned, please complete the following form indicating where the customer would like the CD shipped. Include this form with the warranty returned part.
• 10185621When diagnosing a concern with the SCR system, the technician may notice crystallized DEF (diesel exhaust fluid) on the tip of the DEF injector. Crystallized DEF on the tip of the injector is a normal occurrence and does not indicate that the injector nozzle is clogged. The crystallization will dissolve when the injector is activated. Do not replace the DEF injector for the crystallization alone. Please follow Workshop Manual diagnostics to diagnose the specific condition or DTC on the vehicle.
• 10185616The following information applies to the installation of a customer supplied and commercially available electric trailer brake controller for all 2012MY-2017 MY Hino trucks. This application only applies to brake controllers which operate using a 12-volt input signal from the chassis when the brakes are applied.
• 10185615The following information applies to the installation of a customer supplied and commercially available electric trailer brake controller for all 2008MY-2015MY Hino trucks. This application only applies to brake controllers which operate using a 12-volt input signal from the chassis when the brakes are applied.
• 10185613Bendix Air Dryer Service
• 10185612Exhaust Combustion Chamber with Loose Insulation
• 10185611Def pump backflow connector change
• 10185610Some customer?s may request to enable to Idle Shutdown to save on fuel costs and Idling time. The procedure below will detail how to enable the Idle Shutdown timer.
• 10185609The Burner Control Module (BCU) judges DTC?s P2441 (CAV Stuck), P2300 (Ignition Coil Failure) and P060C (BCU Temp Sensor Failure) on burner start up, if one of the fault conditions is met the BCU can go into a temporary stop mode. If this mode is entered, all regen requests will be ignored and cancelled by the BCU and there will be no DTC?s set
• 10185607Exhaust Control Valve Adjustment Procedure
• 10185603Correction of workshop manual for 2011my-2014my (addition and correction of burner system)
• 10185602Correction of workshop manual for 2011 - 2015 my (revision of troubleshooting procedure for the dtc p2201 & p2214)
• 10185601The following is to inform you of the above caption. This service data should be attached to the relevant pages of the workshop manuals for maintenance and to use for servicing.
• 10185600When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.

Every Hino Conventional Models model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.