2020 Hino Conventional Models

Recalls

1 recall names the 2020 Hino Conventional Models. Newest first.

• Electrical system › Instrument panel › Fuel gauge › Fuel level float/sensor/sending unit

  Aug 8, 2023NHTSA 23V5600008,025 vehicles

  Hino Motors Sales U.S.A., Inc. (Hino) is recalling certain 2020-2024 NE7A, NE7B, NE8A, NH9A, NJ7A, NJ7B, NJ8A, NJ8J, NV7A, NV7B, and NV8A vehicles equipped with 70 or 90 gallon fuel tanks. The fuel sender float may deform and detach, which can lead to an inaccurate fuel gauge reading.

  Risk and remedy

  Risk

  An inaccurate fuel gauge may result in the vehicle unexpectedly running out of fuel and stalling, increasing the risk of a crash.

  Remedy

  Dealers will replace the fuel sender gauge, free of charge. Owner notification letters were mailed October 5, 2023. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is AAV70.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11000898This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
• 11000897After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
• 10235337The purpose of this procedure is to provide instructions in how to properly record Nox Sensors using DX3
• 10231442Conventional diesel particulate filter (dpf) aasw0
• 10231440Conventional nitrogen oxide (nox) sensor aapd0
• 10231439Recovering the doser control unit (dcu) after a failed programming event dcu blank. Tt-23-011
• 102289392011MY-2021MY CONVENTIONAL EXTERIOR MIRROR STAY. The subject vehicle may experience an exterior mirror stay that is loose or drifts slightly from its position. An enhanced mirror stay, mirror stay mount, related fasteners and revised torque specifications have been released to correct this condition. This procedure provides directions for installation of the enhanced components. Reports of looseness have accompanied reports that vehicle operators have folded exterior mirrors inward. As clearly stated in the Hino owners manual, the structure of the mirror stay does not allow for folding.
• 10227282The purpose of this procedure is to provide instructions in how to properly record NOx sensors using DX3.
• 10227281The purpose of this procedure is to provide instructions in performing an injection quantity test on 2011 and newer Conventional or COE series trucks with DX3.
• 10227279The purpose of this procedure is to provide instructions in performing DCU programming on 2011 and newer Conventional or COE series trucks.
• 10227276The purpose of this procedure is to provide instructions in how to perform a manual regen recording on Hino Trucks equipped with a 5th or 7th exhaust fuel injector with DX3.
• 10227273Certain 2017 ~ 2020 model year Hino Conventional vehicles were manufactured with a modified jumper harness between the Transmission Control Module (TCM) and vehicle chassis. The modified jumper harness may allow for potential water intrusion of the modified jumper harness. Water intrusion may cause illumination of the check transmission light on the dashboard. If the illuminated check transmission light is ignored, the transmission may go into fail-safe (or limp mode as it is also called) to protect the transmission from internal damage that could be caused by the fault. While in fail-safe (or limp mode) the transmission will be locked in either 3rd. or 4th. gear. This procedure will provide instruction for replacement of the transmission jumper harness.
• 10227271This parts alert is to inform our dealers that when ordering part number 16400E0E62 passenger side radiator support, it will come with an extra bracket as shown below. When replacing the radiator support brackets, the new passenger side support can be installed with no issues
• 10213495Conventional after turbo catalyst (atc) aapa0. Wp-22-010
• 10213492Conventional particulate sensor (pm) sensor aap60. Wp-22-008
• 10211145Sb-22-007 2020my conventional dtc p0005 and/or p20de, p24a1, p24a2
• 10206065EDGE INSTALLATION GUIDE COE (CAB OVER ENGINE) This procedure will take you step-by-step for installing Bosch hardware on a 2020 and newer Hino COE 195-195h. BULLETIN NO: A-21-005
• 10206060EDGE TELEMATICS INSTALLATION GUIDE - CONVENTIONAL. This procedure will take you step-by-step for installing the Bosch telematics hardware on a 2020 and newer Hino Conventional 238-338. BULLETIN NO: A-21-004
• 10206057SB-21-011 CONVENTIONAL LANE DEPARTURE WARNING (LDW) CAMERA HARNESS REPAIR Subject vehicles equipped with a LDW (Lane Departure Warning) system may exhibit a condition of the engine remaining on after the ignition key is turned to the lock position and removed. In the event that a subject vehicle exhibits this condition, inspect the LDW wiring harness and wires for a pinched wire condition by removing the LDW camera mounting bracket at the roof panel. If the pinch condition is identified, follow the steps in this TSB (Technical Service Bulletin) to repair the condition.
• 10206053SB-21-002 CONVENTIONAL FUEL SENDER LEAK. Certain vehicles may exhibit fuel residue accumulation around the fuel level sensor or cover plate in certain conditions, including if the vehicle is equipped with dual fuel tanks. Updated fuel level sensor bolt sealing washers have been made available to address this condition.
• 10201819Tt-21-008 conventional ABS, esc, cms and ldw diagnosis tech tip
• 10189729WARRANTY ENHANCEMENT PROGRAM XL SERIES DEF SENSOR. May cause the MIL to illuminate due to the following: The wire inside of the DEF sensor is broken. Abnormality of the temperature sensor resistor characteristics in the DEF sensor.
• 10189453BOSTROM - LTSS (LIGHT TRUCK SUSPENSION SEAT) DESIGNED TO FIT THE HINO 155 & 195 COE ? Proven to reduce vibration to the occupant compared to the conventional static seat = LESS FATIGUE ? The suspension system can easily be adjusted to the weight of the driver
• 10189439Hino Trucks floor mats. Black durable rubber floor mats with the red Hino Trucks emblem. Easy to shake out the dirt and debris or clean it with soapy water.
• 10189424Hino COE Quick Reference Guide
• 101848552005 through current model year trucks equipped with an Aisin transmission. When rekplacing an Ais in transmission, the below transmission return form is required to be filled out. Include this form with the warranty returned part.
• 10182727This document is to inform of the following information regarding the replacement and installation of the Aisin 450-43 LE Automatic Transmissions.
• 10182676This document is to inform of the procedure to calibrate the Pulse Adjust Module when needed (ex. tire size change, rear carrier ratio change) .
• 10179168This service campaign will advise you how to install tow hooks on certain Conventional trucks.
• 1017775920MY Conventional trucks equipped with a bubbler filter 23304-EV460 may set Diagnostic Trouble Codes (DTC's) P20DE and/or P0005 under some conditions. If a truck comes into your location exhibiting these DTC's and is equipped with the 23304-EV460 bubbler filter, replace the filter with 23304-EV023 and retest.
• 10177758Hino is performing a reliability collection of the outside mirror glass to identify potential defects and improve the quality of this component. This service alert will advise you how to remove the outside mirror covers, document the mirror assembly manufacturing dates, and then direct you to contact the technical assistance center for repair direction.
• 10177754This procedure will take you step-by-step for installing an LMU 3640 on a 2020 and newer Hino Conventional 238-338.
• 10168587M0330 outside mirror adhesion labor time change
• 10165538Conventional dcu and ecu software enhancement
• 10164289Inadequate adhesion of the outside mirror glass to the mirror carrier plate may cause the mirror glass to separate. Mirror glass that separates from the mirror carrier plate may impair the drivers visibility. Complete detachment may create road debris that could strike another vehicle or pedestrian. These may create a risk of accident or injury. In the following procedure after confirmation of the build date of each of the suspect truck mirrors, those containing mirrors that fall within the suspect range, will be replaced.
• 10164288The following tech tip is to assist in replacing the engine fuel filter.
• 10164286The following tech tip is for fixing hard steering or power steering pump noise on a Hino Conventional truck.
• 10159331Sb-19-012 exhaust valve inspection workshop manual correction
• 10156480SB-19-010 P204B DTC WORKSHOP MANUAL CORRECTION. Workshop manual correction of Diagnostic Trouble Code (DTC) P204B.
• 10156478SB-19-009 P204B DTC WORKSHOP MANUAL CORRECTION. Workshop manual correction of Diagnostic Trouble Code (DTC) P204B.

Every Hino Conventional Models model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.