2011 Jeep Compass
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Jeep › Compass › 2011
These records cover every 2011 Jeep Compass. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2011 Jeep Compass. Newest first.
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Chrysler 200, 2010 Chrysler Sebring, 2010-2012 Dodge Caliber and 2010-2014 Jeep Patriot, Compass and Dodge Avenger vehicles. The Occupant Restraint Control (OCR) module may short circuit, preventing the frontal air bags, seat belt pretensioners, and side air bags from deploying in the event of…
Risk and remedy
Risk
If the frontal air bags, seat belt pretensioners, and side air bags are disabled, there is an increased risk of injury to the vehicle occupants in the event of a vehicle crash that necessitates deployment of these safety systems.
Remedy
Chrysler will notify owners, and dealers will replace the OCR, free of charge. Interim letters informing owners that parts are not available yet were mailed on October 26, 2016. The recall began on August 15, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S61.
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2012 Jeep Compass and Patriot vehicles manufactured May 6, 2008, through July 20, 2012. The affected vehicles have a software error which may result in a delayed deployment or non-deployment of the seatbelt pre-tensioners and/or side airbags.
Risk and remedy
Risk
In the event of a rollover necessitating airbag deployment, the software error can lead to a delayed deployment or non-deployment of the side curtain airbag and/or seatbelt pre-tensioners. As a result, vehicle occupants have an increased risk of injury in a crash.
Remedy
Chrysler will notify owners, and dealers will correct the software free of charge. The recall began June 21, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall number is N01.
Chrysler IS recalling certain model year 2011dodge journey, jeep wrangler, chrysler 200, chrysler 200 convertible, dodge avenger, dodge nitro, jeep liberty, dodge caliber, jeep compass, jeep patriot, dodge grand caravan and chrysler town & country vehicles. some of these vehicles may have been built with a missing or incorrectly installed steering column…
Risk and remedy
Risk
A missing or incorrectly installed rivet could compromise the ability of the steering column to support the occupant loads in the event of a frontal crash, decreasing the effectiveness of the frontal impact safety system. as a result, the condition may increase the potential for injury in a frontal crash.
Remedy
Dealers will inspect for rivet presence and alignment and repair the steering column pivot as required, free of charge. the safety recall began on july 4, 2011. owners may contact chrysler at 1-800-853-1403.
Owner complaints
188 complaints7 involved a crash2 involved a fire5 injuries
What owners report most
Latest complaints
- Suspension
The crossmebers front and rear were rusted to where the back broke and made the car unsafe and unable to drive
- Electrical system · Power train · Vehicle speed control
[XXX] [XXX] , [XXX] [XXX] 2/7/26 To Whom It May Concern, I am writing to formally express my concern regarding ongoing, critical safety issues with my vehicle, which have been increasingly dangerous while driving. These issues appear to be interconnected and involve multiple components…
[XXX] [XXX] , [XXX] [XXX] 2/7/26 To Whom It May Concern, I am writing to formally express my concern regarding ongoing, critical safety issues with my vehicle, which have been increasingly dangerous while driving. These issues appear to be interconnected and involve multiple components, including the valve body, transmission, TCM, ABS module, ECM, and throttle body. These problems have posed significant risks to my safety and the safety of others on the road. On several occasions, while driving at highway speeds (approximately 70 mph), the traction control and ABS warning lights have illuminated, and the vehicle has suddenly lost acceleration. This malfunction seems to cause the car to change gears unexpectedly or, in some instances, stop accelerating altogether. As a result, I have been forced to pull over to the side of the road in order to perform a YouTube-suggested reset just to get my vehicle back in motion. This situation has nearly led to accidents, as I have found myself stranded in traffic, unable to accelerate, or worse, pulling into traffic where the car fails to accelerate, almost causing collisions with other vehicles. Additionally, during colder weather, I have experienced issues with the throttle, where it becomes erratic and unresponsive. Despite having multiple repairs made, the problem persists, and I have observed that the throttle may either rev unexpectedly or fail to shift at all. While I understand that some repairs have been made, I am deeply concerned that the vehicle's ongoing malfunctions are indicative of serious safety hazards, which should be addressed by a professional dealership, at no cost rather than being dismissed with the assertion that "it won’t hurt anything." Given the potential for life-threatening incidents and the fact that I have already had several close calls, I strongly urge that these issues be diagnosed and rectified by a certified dealership or technician. , ran out of spac INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(
- Seats
The vehicle pulls when I’m driving it and the transmission over heats if I go over 80 and turns off.
- Structure
The contact owns a 2011 Jeep Compass. The contact stated that while driving over a railroad track at approximately 15 MPH, the vehicle suddenly decelerated and was difficult the steer. The vehicle was later towed to the local dealer, who diagnosed that the front subframe had failed due to severe…
The contact owns a 2011 Jeep Compass. The contact stated that while driving over a railroad track at approximately 15 MPH, the vehicle suddenly decelerated and was difficult the steer. The vehicle was later towed to the local dealer, who diagnosed that the front subframe had failed due to severe corrosion, causing damage to the engine bay, and causing the engine and transmission to lower. The subframe and front lower control arms were replaced, and the vehicle was repaired. Recently, while the vehicle was in for routine maintenance, the contact was informed that the rear subframe was corroded. The vehicle was not yet repaired. The manufacturer was not yet contacted. The failure mileage was 98,500.
- Electrical system
The vehicle shuts off while driving at any speed. Steering locks and will not allow driver to pull over to safety.
- Power train · Service brakes · Vehicle speed control
speedometer doesn't work, ABS, Brakes, engine and traction light keeps on. THE SHIFT LEVER CHANGES BY ITSELF FROM D TO M while driving. ABS module has to be replaced at my cost when other 2011 jeep compass have a recall F 50 for the same issue.
- Engine · Fuel system, gasoline
The contact owns a 2011 Jeep Compass. The contact stated while driving 30 MPH after refueling, the vehicle stalled. The vehicle was restarted and worked as designed; however, the failure recurred while driving after refueling. There were no warning lights illuminated. The contact called the local…
The contact owns a 2011 Jeep Compass. The contact stated while driving 30 MPH after refueling, the vehicle stalled. The vehicle was restarted and worked as designed; however, the failure recurred while driving after refueling. There were no warning lights illuminated. The contact called the local dealer, but the vehicle was not diagnosed or repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 64,000.
- Steering · Suspension · Unknown or other
Rust thru/failure of the front cross member subframe. I noticed a clicking/rubing sound coming from the front of my 2011 Jeep Compass. Over several days it got worse. I took the car to the same dealership that I bought the car from new and was told it was a rust thru on the subframe and that the…
Rust thru/failure of the front cross member subframe. I noticed a clicking/rubing sound coming from the front of my 2011 Jeep Compass. Over several days it got worse. I took the car to the same dealership that I bought the car from new and was told it was a rust thru on the subframe and that the car was not safe to drive. At this point there were NO warning lights or other indication that the front end was approaching a catastrophic failure. I contacted Jeep and was told that a special 10 year extended warranty had expired in 2022. The dealer offered no help in covering the cost either. I was never informed about the extended warranty, or I would have had the car checked. The thing that really makes me mad is the rust thru occurred on only one side because the A/C drain was routed so it dripped condensation onto the frame on that side. I have the subframe and have included pictures.
- Fuel/propulsion system · Unknown or other
Cuando estoy con el vehiculo en marcha suben las revoluciones del vehiculo este diminuye la velocidad corriendo, lo cual podria ocacionar un accidente
- Structure › Body · Suspension
The rear subframe and suspension are rusted. I have been hearing a rattling sound for the past couple of weeks, especially when driving over bumps. When I took the car to my mechanic, he detected a cracking in the rear subframe/suspension due to the rust. If this would totally break it would be a…
The rear subframe and suspension are rusted. I have been hearing a rattling sound for the past couple of weeks, especially when driving over bumps. When I took the car to my mechanic, he detected a cracking in the rear subframe/suspension due to the rust. If this would totally break it would be a substantial safety risk to myself, the driver, as well as other drivers on the road. No warning lights or messages appeared on the car to warn of this problem.
- Suspension · Wheels
2011 Jeep Compass with 62,000 miles on it the subframes rod about the wheel almost fell off the arm that holds the wheel fell off the rear frame and that could have caused the real big accident accident would have lost control of the vehicle and they told and dealership told me that the warranty…
2011 Jeep Compass with 62,000 miles on it the subframes rod about the wheel almost fell off the arm that holds the wheel fell off the rear frame and that could have caused the real big accident accident would have lost control of the vehicle and they told and dealership told me that the warranty expired 2 years ago it was a 10-year extension on it so they did not do it it's because they used cheap metal and they know they did but they will not fix it I just fixed the rear subframe and all parts going to it and all bolts cost me 1500 dollars I do not think that's fair I hope you look into it because they are robbing people thank you I hope you can do something about it and I can get reimbursed and have my front one fixed too because that is rotted out too I just don't have the money to do both
- Steering · Wheels
Front wheel assembly with broken connection to frame which was caused by a rusted out frame that mechanic said make vehicle extremly dangerous to drive. Front Wheels buckled outward. Can't drive car any more.
- Suspension
Please require Jeep/Stallantis to initiate a recall for all 2008-2012 Jeep Compass' impacted by excessive corrosion to the subframe and front/rear cross members due to an inadequately designed AC drain located right above the vehicle subframe. Condensation from the AC drain drips directly onto…
Please require Jeep/Stallantis to initiate a recall for all 2008-2012 Jeep Compass' impacted by excessive corrosion to the subframe and front/rear cross members due to an inadequately designed AC drain located right above the vehicle subframe. Condensation from the AC drain drips directly onto critical frame structures. Therefore, excessive and premature rusting to the front & top sides of the subframe occurs because the subframe is constantly wet with the operation of the AC, as well as during the winter months while dehumidifying the air. Of course, road salt throughout the winter in the “salt” states further exacerbates the problem. Extensive rust to the subframes have deemed the vehicles unsafe to drive despite being in otherwise good condition w/ reasonable miles. No safety/dashboard lights, warnings, or operational concerns were present indicating potential safety concerns until the driver either experienced a dangerous driving situation or failed a vehicle inspection. Jeep has known about the significant safety implications, yet failed to effectively remediate critical safety concerns. Although Jeep extended a Front and Rear Crossmember Warranty (X69 Warranty), they neglected to properly notify vehicle owners of the extension. They did not make any type of public announcement to inform or warn drivers of the critical safety issues, did not notify owners of access to free yearly inspections to monitor the subframe. Owners using independent mechanics rather than OEM Jeep dealers have not been afforded the same opportunity to access the X69 Warranty Extension & inspections. Jeep has yet to demonstrate sufficient accountability for the ongoing critical safety and security concern. Acknowledging an insufficient AC drain design and issuing a recall for the AC drain, subframe, and front/rear cross members affirm they stand behind their brand, reputation, & value passenger and vehicle safety.
- Seats
Headrest clips broke and popped out
- Structure › Body
Was told that the sub frame is bad. After looking into it, it seems to be a known issue with the jeep compass.
- Suspension · Unknown or other
Was told by service center that car was not safe to drive
- Steering · Suspension · Unknown or other
Front subframe rusted out due to salt corrosion and as Kentucky is not listed as a Salt belt state the recall notice went unsent and the consumer was not advised nor were service locations.
- Suspension
while running errands, a woman pointed out to me that i had dropped the rear passenger side control arm. she was very concerned about me driving it. i assured her i understood. and that with a mile to drive, i would use flashers and drive slowly. the following day my Compass was brought to my…
while running errands, a woman pointed out to me that i had dropped the rear passenger side control arm. she was very concerned about me driving it. i assured her i understood. and that with a mile to drive, i would use flashers and drive slowly. the following day my Compass was brought to my mechanic. i received a phone call i never expected! the rear crossmember was rusted out, and the subframe. above that, there was nothing to bolt to! the car was scrap- and, yes, it is available for inspection. this absolutely is a safety issue. the steering became unpredictable, harder to control. i could have lost a wheel, caused an accident that could have been fatal! the disabled car should not be on the road. i did visit the dealership local to me. i carried with me a TSB dated March 2017 about this very issue. i was told my car was "old" and did i get it serviced there? unfortunately, no, i bought it used 2 years ago. there had been a 10 year warranty extension and now my car was out of warranty? i had no notification. and, even so, why would Jeep deliberately ignore all the complaints on THEIR forums? three people at that dealership knew of this problem and said there was nothing they could do. my car is a 2011, i am a risk-free driver, no accident history. the car itself is clean. there is 40,000 miles on it. the previous owner was meticulous with service calls, getting recalls fixed, oil changes etc. the car was solid when i bought it. i did not abuse, misuse, or neglect my Compass in any way. this is a defect on the manufacturer's end. the folks on your very site are detailing the same severe corrosion. the 2011 and 2012 Compasses and 2011-2012 Patriots were affected. there are forums with owners trying to get compensated, trying to bring attention to this.
- Suspension
The suspension has completed rusted through. My mechanic can stick his arm all of the way through. There was a recall on other VINs but not mine so far. There needs to be one since I wasn't told about this safety problem until my mechanic went to replace other parts. I was never told this through any means. Jeep needs to do better. I am now out of a car and will have to pay thousands just to get the parts fixed.
- Suspension
In 2019 my 2011 jeep compass front subframe rusted really bad which cause corrosions. I called Chrysler and advise if there was a recall on this and they told me no. I paid for the repair to get it fix, fast forward to today I took my car in for an oil change and was informed the rear subframe has…
In 2019 my 2011 jeep compass front subframe rusted really bad which cause corrosions. I called Chrysler and advise if there was a recall on this and they told me no. I paid for the repair to get it fix, fast forward to today I took my car in for an oil change and was informed the rear subframe has now rotted and is also causing corrosion. I called Jeep and was advise the recall expired in 2021 and there is nothing they can do. Please be mindful that I was told that there was no recall on this back in 2019 when I called. It is very unsafe for me to drive with my 4 year old in the car knowing that my subframe is severely rotted which is causing corrosions. jeep was not willing to help with this recall and I think it’s insane due to it being a safety issue
- Unknown or other
We had our Jeep at the local mechanic for a pre winter check up. He found the rear crossmember broken and the front crossmember had holes in it due to corrosion. The vehicle has 211,000 km on it and we’ve owned since new with zero collisions or even a fender bender. Jeep had an extended warranty on…
We had our Jeep at the local mechanic for a pre winter check up. He found the rear crossmember broken and the front crossmember had holes in it due to corrosion. The vehicle has 211,000 km on it and we’ve owned since new with zero collisions or even a fender bender. Jeep had an extended warranty on these pcs but has denied our claim as 10 years have passed. In my mind this is a safety issue as the wheel assembly could physically break free causing loss of control of the vehicle. These are parts related to the structural integrity of the vehicle and not a normal wear and tear item. This vehicle has been serviced by our local journeyman mechanic licensed in Alberta. It was at our local dealership on September 15/2017 for a recall but there is no record of inspection of these crossmembers. Jeep service bulletin dated march 10/2017 states that the affected vehicles should have these parts inspected and replaced if necessary..also to add, we never received any correspondence from Jeep asking to bring the vehicle in for inspection. The vehicle has been parked for several days now as both our mechanic and myself believe it’s not safe to be on the road. I’ve gotten nowhere with the district warrant manager or their customer care line staff. I’m reaching out as I believe this is a serious issue and should be a safety recall rather than a service bulletin.
- Structure › Body · Suspension
My mechanic reported that car's rear control arm has broken away from frame of car and is a very unsafe condition to use. No warning was given. Was found during normal inspection on mechanics lift. Manufacturer would not help during owners notification of problem but recognized the seriousness of the problem. Dealer has not been notified just my mechanic professional's recommendation.
- Structure › Frame and members
The contact owns a 2011 Jeep Compass. The contact stated while driving approximately 45 MPH, the vehicle rear end swerved to the right while driving straight. The contact stated no warning light was illuminated. The contact regained control and stopped the vehicle. The contact inspected the vehicle…
The contact owns a 2011 Jeep Compass. The contact stated while driving approximately 45 MPH, the vehicle rear end swerved to the right while driving straight. The contact stated no warning light was illuminated. The contact regained control and stopped the vehicle. The contact inspected the vehicle and noticed that the rear underside was severely rusted; causing the rear suspension to separate from the under body. The contact was able to drive to his residence. The contact had not taken the vehicle to a local dealer. The vehicle had not been diagnosed or repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 105,000.
- Structure › Frame and members · Suspension
The contact owns a 2011 Jeep Compass. The contact stated that upon taking her vehicle to an independent mechanic to have the wheels aligned, she was informed that the work could not be performed due to severe subframe corrosion. The vehicle was then taken to a second independent mechanic who…
The contact owns a 2011 Jeep Compass. The contact stated that upon taking her vehicle to an independent mechanic to have the wheels aligned, she was informed that the work could not be performed due to severe subframe corrosion. The vehicle was then taken to a second independent mechanic who provided the same diagnosis. The manufacturer was notified of the failure but offered no assistance. The vehicle was not repaired. The failure mileage was approximately 133,000.
- Fuel/propulsion system · Unknown or other
After 4 years of driving my 2011 Jeep Compass and hitting 95,000 miles on it, I noticed that there were problems with filling up my tank and my car stalling. If I don't stop the gas pump myself, a few seconds after pulling out of the gas station my car would stall and idle until my engine would…
After 4 years of driving my 2011 Jeep Compass and hitting 95,000 miles on it, I noticed that there were problems with filling up my tank and my car stalling. If I don't stop the gas pump myself, a few seconds after pulling out of the gas station my car would stall and idle until my engine would just shut off and my wheel and break would lock. This happened while entering a highway, going into a busy intersection, and trying to get out of large mall space. In all of these settings, I was inches away from a car crash. I have brought this up to multiple mechanics who have never heard of this problem and weren't sure what to do. After doing my own research I realized that this is a common Chrysler/Jeep issue with models made between 2005-2015 models. There are no warning lamps, messages, or any signals that my car is going to stall and idle. I could not imagine a larger safety risk to myself, my passengers, and all of the drivers around me. Last week after filling up my tank and intentionally not filling it up all the way, I thought I was safe to drive home but I was wrong. As I was crossing the intersection five-way traffic, my car began to stall as a semi-truck was heading right into me. Thankfully, I shut my engine off and quickly turned it back on to move out of the middle of the road.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Active Head Rest Inadvertent Deployment
The Office of Defects Investigation (ODI) opened PE19014 on September 9, 2019, to investigate 128 consumer complaints alleging that the Active Head Rest (AHR) inadvertently deployed without the occurrence of a crash or other rear impact event in model year (MY) 2014 Jeep Grand Cherokee and Dodge Durango vehicles.When…
The Office of Defects Investigation (ODI) opened PE19014 on September 9, 2019, to investigate 128 consumer complaints alleging that the Active Head Rest (AHR) inadvertently deployed without the occurrence of a crash or other rear impact event in model year (MY) 2014 Jeep Grand Cherokee and Dodge Durango vehicles.When ODI opened the investigation, ODI was aware of thirteen alleged injuries.A small number of Early Warning Reports identified driver and/or passenger front seat AHR inadvertent deployments without a rear impact event.Reported safety consequences resulting from the AHR deployments include concussions, headaches, soft tissue injuries, disorientation, nausea, vomiting and/or loss of vehicle control as a result of being surprised and distracted by being struck in the head by the inadvertent AHR deployment. On September 24, 2019, ODI sent an Information Request (IR) letter to Fiat Chrysler Automobiles (FCA).ODI requested certain detailed information from FCA related to the following subject vehicles: MY 2010-2014 Dodge Avenger 200, MY 2010-2014 Dodge Calber, MY 2010-2014 Chrysler Sebring, MY 2013-2015 Ram Tradesman, MY 2012 Ram Van, MY 2010-2019 Dodge Grand Caravan, MY 2010-2016 Chrysler Town and Country, MY 2010-2017 Jeep Compass, MY 2011-2020 Dodge Durango, MY 2011-2020 Jeep Grand Cherokee, MY 2010-2019 Dodge Journey, MY 2010-2012 Jeep Liberty, MY 2010-2011 Jeep Nitro, and MY 2010-2011 Jeep Patriot vehicles.On December 2, 2019, ODI received a response from FCA that included vehicle production data, consumer complaints, field reports, warranty claims, manufacturer actions, production changes, and other data related to the alleged defect from the start of production (2010) through September 24, 2019.On January 27, 2020, ODI received an update to the December 2, 2019, IR response from FCA.On September 22, 2020, ODI requested additional subject vehicle AHR information from FCA.ODI received FCA's response on October 21, 2020.ODI subsequently received an update to FCA's October 21, 2020, response on February 16, 2021.During the investigation, ODI requested updates to certain IR questions on two occasions.FCA provided updates to question #2 on March 5, 2021, and questions #2 and #5 on May 26, 2023. FCA’s IR response data identified approximately 7.5 million subject vehicles (with approximately 15 million AHR assemblies).Due to the large number of vehicles and failure reports, ODI focused its analysis on the FCA vehicle model with the highest failure rate to represent the worst-case scenario.For this purpose, ODI focused on MY 2012-2015 Jeep Grand Cherokee vehicles for its analysis.This population includes 710,890 vehicles that FCA manufactured between August 19, 2011, and August 8, 2015.ODI identified 2,839 alleged AHR failures within this limited population.ODI identified 263 alleged injuries that were caused by AHR failures in MY 2012-2015 Grand Cherokees vehicles.Of these alleged injuries, ODI categorized them as eighty-two (82) soft tissue (neck/whiplash, bruise) injuries, four (4) concussions, fifty-nine (59) headaches, and one hundred eighteen (118) without a specific injury description.Although complainants have alleged injuries, ODI has been unable to obtain evidence to substantiate or validate any injuries where medical treatment was required.Consumer outreach was conducted by ODI, where sixty-three (63) FCA complainants with alleged injuries were contacted.Twelve of the sixty-three FCA consumers responded and were interviewed by ODI.ODI requested medical records, however, only one response was provided. Attorneys representing the responding complainant provided a synopsis that indicated they had experienced prior neck-related injuries dating to the mid-1990s.ODI also contacted one hundred (100) consumers who submitted Vehicle Owner Questionnaires (VOQ) in an attempt to validate alleged injuries. Despite the efforts of ODI, the office has been unsuccessful at obtaining substantive documentation/evidence supporting complaints that allege serious injuries (where pre-existing medical conditions did not already exist). In addition to the low severity of alleged injuries caused by AHR deployments, there have been eleven alleged crashes and two alleged lane departures within the entire subject vehicle population that has been in the field up to sixteen years (with over 8,500 AHR inadvertent deployments).ODI was not able to validate that the alleged crashes were the result of inadvertent head rest deployments, and the crashes were minor in nature. ODI has conducted a thorough investigation of the alleged safety defect and with up to sixteen years of exposure for some vehicles and over 8,500 inadvertent AHR deployments, no serious crashes or injuries could be validated in the sub-population of focus.The lack of serious injuries validated by ODI with such large period of field exposure is consistent with thework done by NHTSA’s Human Injury Research Division and the Biodynamic Research Corporation, which support that an inadvertent AHR deployment is not likely to cause serious injury.In addition to the low risk of injury, FCA released an extended warranty program that covers inadvertent AHR deployment for ten years / unlimited mileage from the vehicle's in-service date. PE19014 is closed with the FCA extended warranty program.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist, and the Agency reserves the right to take additional action if warranted by new circumstances. To review a complete closing summary, please the attached closing report. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10242717Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
- 102320012.0L Powertrain Diagnostic And System Enhancements
- 10231753Emissions recal U67 Catalytic Converter Efficiency
- 10230438Some of the above-involved vehicles may exceed NOx (Oxides of Nitrogen) emission level standards due to loss of catalytic converter efficiency
- 10229998KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
- 10229871Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
- 10229825RHW RHP Radio Software Enhancements
- 10229572Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10228020Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
- 10227983If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
- 10225424Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10225287Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10224076Active Head Restraint (AHR) Inadvertent Deployment - X86 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
- 10224059Warranty Bulletin D-20-18 (X86) Active Head Restraint - Select 2010-2017 Jeep Compass (MK) and 2010-2012 Dodge Caliber (PM)
- 10223677This bulletin involves inspecting the front and rear crossmembers for perforation/rust through and if necessary, replacing the crossmember(s). Customers may describe a vibration at the steering wheel or may have been informed by a technician or state vehicle inspection that the front and/or rear crossmember is severely corroded.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10223512THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
- 10223509TRANSMISSION, 5 Speed On replacing OE transmission 05106567A$/68042567A$ with reman transmission R8142074A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
- 10223508TRANSMISSION, 5 Speed Replacing OE transmission 05106789A$/68042789A$ with reman transmission R8142073A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
- 10223386KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
- 10223226KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10220993RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect
- 10220403New Safety Recall Advanced Communication ? N01060613 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2010 through 2012 model year (MK) Jeep Compass and Patriot vehicles. Some of the above vehicles were built with a software error in the Occupant Restraint Control (ORC) module. The ORC software error may result in delayed or non-deployment of seatbelt pre-tensioner or side airbag curtains involved in certain low-speed rollover events. Chrysler will conduct a voluntary safety recall on all involved vehicles to reprogram the ORC module with the corrected software. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.
- 10220106No Start After Powertrain Control Module (PCM) Replacement and/or Reprogramming
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220098Authentic Mopar Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar Glass.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10218806Lower Control Arm Cold Temperature Squeak/Creak Noise This bulletin involves applying Nye lubricant to the front lower control arm rear bushing. Customer may describe a creak or squeak noise coming from the front suspension. Noise is typically more noticeable during cold temperatures below 4C (40F), noise may go away when temperature warms up.
- 10218783Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
- 10218303RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
- 10218211Flash: 2.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a slight idle instability while idling in gear with the brake released. New software has been developed to address this concern. Also included in this update is an enhancement to the Variable Valve Timing (VVT) system.
- 10217965Lower Control Arm Cold Temperature Squeak/Creak Noise This bulletin involves applying Nye lubricant to the front lower control arm rear bushing. Customer may describe a creak or squeak noise coming from the front suspension. Noise is typically more noticeable during cold temperatures below 4C (40F), noise may go away when temperature warms up.
- 10217942Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
- 10217569Failure Code Change This bulletin involves notifying the dealers and technicians of a change to the Required Flash (RF) and Customer Concern (CC) failure codes.
- 10217559Front And Rear Crossmember Corrosion (X69 Warranty Extension) This bulletin involves inspecting the front and rear crossmembers for perforation/rust through and if necessary, replacing the crossmember(s). Customers may describe a vibration at the steering wheel or may have been informed by a technician or state vehicle inspection that the front and/or rear crossmember is severely corroded.If the customer describes the symptom/condition listed above, perform the Diagnostic Procedure.
- 10217521Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
Every Jeep Compass model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.