2023 Ford E-250

Recalls

1 recall names the 2023 Ford E-250. Newest first.

• Equipment › Other › Labels

  May 27, 2022NHTSA 22V3840005,247 vehicles

  Ford Motor Company (Ford) is recalling certain 2022 F-Super Duty F-250, F-350, F-450, F-550, F600, and 2023 E-Series vehicles. In addition, certain 2016 E-Series, 2017 and 2019 F-450, 2021 F-350, and 2021 Transit vehicles that received a reprinted label are also included in this recall. The Safety Certification Labels are missing the tire size, rim type…

  Risk and remedy

  Risk

  Missing tire information could lead to an incorrect tire or rim being installed, or incorrect tire pressure, increasing the risk of a crash.

  Remedy

  Dealers will replace the Safety Certification Label, free of charge. Owner notification letters were mailed July 6, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C09.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11008373In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Reason for supplement: software now available/additonal technician information
• 110011132023-2024 F-Super Duty/F-53 Motorhome Chassis/F-59 Commercial Stripped Chassis and 2023-2025 F-650/F-750/E-Series vehicles equipped with a Dana rear axle and built on or after 01-Nov-2022 may have orange/red RTV sealant used as the gasket on the differential housing cover. This does not indicate any previous repairs as it is used by Dana during assembly.
• 10254127Some 2023-2024 F-Super Duty/F-53 Motorhome/F-59 Commercial Stripped Chassis or 2023-2025 E-Series/F-650/F-750 vehicles equipped with a gas engine may exhibit an illuminated MIL with ignition system DTC(s) P0352, P0353, P0354, P0355, P0357, P2303, P2306, P2309, P2312, P2318, P2304, P2307, P2310, P2313, P2319, and/or P2322 set in the powertrain control module (PCM). This may be due to incorrect cylinder to DTC mapping within the PCM. This means the DTCs listed may set against the incorrect cylinder. Even though the cylinder to DTC mapping is incorrect in the PCM, the presence of these DTCs means that a real ignition system concern is present that requires diagnosis and repair. Prior to performing a pinpoint test for one of the listed DTCs, it will be necessary to identify the correct cylinder that has the issue. Do this by using the Ford diagnosis and repair system (FDRS) to perform a cylinder power balance test. If the results show two cylinders dropping out, begin diagnosing the ignition system components for the cylinder that is dropping out and not setting an ignition related DTC. Due to the incorrect incorrectcylinder to DTC mapping, the PCM will shut off fuel to the cylinder that the PCM has triggered a DTC against. Diagnosing the cylinder that does not set an ignition DTCand drops during the power balance test, will verify the identity of the cylinder that has the concern. If only onecylinder is dropping out, start diagnostics with that cylinder. Refer to the Workshop Manual, Section 303-07A/C.
• 10252410Customer Satisfaction Program 22N15 Certain 2020-2023 Model Year Bronco Sport, Escape, Corsair, E-Series, F-650/F-750, F-53 Motorhome Chassis, F-59 Commercial Stripped Chassis Vehicles Equipped with Smart Data Link Connector (SDLC) Gateway Module Reprogramming for Inspection and Maintenance (I/M) Testing Adding Not OTA Capable Owner letters. Other documents submitted 01/02/24 & Received OTA letters submitted on 02/01/24
• 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
• 10248277This article supersedes TSB 23-2258 to update the Parts List, TSB Issue, and Service Procedure. Some 2021-2023 E-Series vehicles may exhibit a lack of air flow due to an inoperative heating, ventilation, and air conditioning (HVAC) blower motor. This may be due to a damaged fuse F2 (50A) in the battery junction box (BJB). To correct the condition, replace the BJB, pigtail connector, and replace fuse F2 in the new BJB with the listed service replacement part.
• 10241529Some 2021-2023 E-Series vehicles may exhibit a lack of air flow due to an inoperative heating, ventilation, and air conditioning (HVAC) blower motor. This may be due to a damaged fuse F2 (50A) in the battery junction box (BJB). To correct the condition, replace the BJB and replace fuse F2 in the new BJB with the listed service replacement part.
• 10240743The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
• 10237971Some 2021-2023 F-Super Duty/E-Series vehicles equipped with a 6.2L, 6.8L or 7.3L gasoline engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 and/or P0455 stored in the powertrain control module (PCM). This may be due to a improper fuel filler cap installation and/or outside contamination on the fuel cap sealing surface. The fuel filler cap requires multiple turns to seal properly and should be clean of any debris on sealing surface. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. If the DTCs return after the fuel filler cap is cleared of debris and properly seated, refer to Workshop Manual (WSM), Section 303-13 > pinpoint test HX.
• 10228876Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
• 10228871Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit an intermittent no crank/no start condition and/or an intermittent blank instrument panel cluster (IPC)/SYNC touchscreen. This may be due to the software in the gateway module (GWM). To correct the condition, reprogram the GWM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14F642 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10216963Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit a communication fault with emissions inspection equipment. This may be due to the software in the gateway module (GWM). To correct this condition, reprogram the GWM to latest software level using the appropriate Ford diagnostic scan tool. Use causal part 14F642 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10216961Some 2021-2022 F-Super Duty and 2021-2023 E-Series vehicles equipped with a 6.2L or 7.3L gasoline engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 stored in the powertrain control module (PCM). This may be due to a loose fuel filler cap. The fuel filler cap design has changed, requiring multiple turns to seal properly. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. For further diagnostics, refer to Workshop Manual (WSM), Section 303-13 - pinpoint test HX.
• 10212957Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Every Ford E-250 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.