2024 Ford E-350

Recalls

1 recall names the 2024 Ford E-350. Newest first.

• Power train › Automatic transmission › Internal › Park pawl

  Sep 8, 2023NHTSA 23V6250005,919 vehicles

  Ford Motor Company (Ford) is recalling certain 2024-2025 Ford E-350, F-650, and F-750 vehicles. The park pawl may not fully engage the park gear due to a casting defect in the transmission.

  Risk and remedy

  Risk

  A vehicle which does not have the park pawl fully engaged may result in a vehicle rollaway, increasing the risk of a crash.

  Remedy

  Dealers will inspect and replace the transmission, or the valve body and extension housing, as necessary, free of charge. Owner notification letters were mailed January 16, 2024. Owners may contact Ford's customer service at 1-866-436-7332. Ford Motor Company's number for this recall is 23S54.

  Full recall details →

Owner complaints

What owners report most

1. Power train1
2. Wheels1

Latest complaints

• Jul 20, 2026TX
  Wheels
  On two separate occasions, the vehicle's left rear wheel studs have broken off clean with the hub and both rear dual wheels departed the vehicle while in motion. This issue was reported to the local FORD dealer and they reported that they do not know why this is happening. This has happened to…

  On two separate occasions, the vehicle's left rear wheel studs have broken off clean with the hub and both rear dual wheels departed the vehicle while in motion. This issue was reported to the local FORD dealer and they reported that they do not know why this is happening. This has happened to five (5) of our other vehicles as well. I am a fleet manager for an EMS service and we have a total of ten (10) of these Ford chassis. The wheels coming off present a hazard to oncoming traffic not to mention the safety of our team members and patients being transported on our ambulances. We sent the vehicle to Kilgore Ford in Kilgore, Texas and they advised they are not sure how this keeps happening. There were no warning lamps that gave the driver a warning that something was wrong until the truck started vibrating and the wheels came off. All of our vehicles, including these FORD Chassis', undergo Preventative Maintenance every 5,000 miles and we check torque on these FORD chassis' because of these continued failures. Our torque wrenches are checked annually for calibration and we utilize the FORD Diagnostic Software and FORD Torque Specification which are followed on every preventative service.

• Nov 3, 2023NY
  Power train

  Van does not always engage in reverse. Slips into neutral instead and rolls. Takes several attempts, sometimes over the course of 10+ minutes to get the transmission to engage into reverse. Problem has been intermittent over the past 30 days. May be related to NSTSA Recall 23V625 although not as described in notice 23S54

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11009425Ford Customer Relationship Center (CRC) phone call to Customers Communication Script and FAQ relating to 23H07 Harvest program
• 11008948While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
• 11008373In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Reason for supplement: software now available/additonal technician information
• 11006033Certain 2020-2024 Super Duty and 2021-2025 Model Year Econoline Equipped With a 6.8L or 7.3L Gasoline Engine Powertrain Control Module (PCM) Software Update REASON FOR THIS SUPPLEMENT Software Availability Update: Software is now available to repair 2021-2022 and 2025 Model Year Econoline vehicles. The service action has been updated accordingly. Technical Information: IDS programing information has been added for 2021-2023 Model Year Econoline Vehicles.
• 11002845Certain 2020-2024 Super Duty and 2021-2025 Model Year Econoline Equipped With a 6.8L or 7.3L Gasoline Engine Powertrain Control Module (PCM) Software Update In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Routine occurrences of prolonged idle time may result in excess wear to the engine camshaft lobes and valve tappet surfaces due to reduced lubrication. Over time, the engine may progressively run rough due to cylinder misfire. Additionally, customers may hear engine tapping noises and the Check Engine Light (CEL) may illuminate
• 11001148Certain 2023-2024 Super Duty and 2021-2025 Model Year Econoline Equipped With a 6.8L or 7.3L Gasoline Engine - Powertrain Control Module Software Update
• 110011132023-2024 F-Super Duty/F-53 Motorhome Chassis/F-59 Commercial Stripped Chassis and 2023-2025 F-650/F-750/E-Series vehicles equipped with a Dana rear axle and built on or after 01-Nov-2022 may have orange/red RTV sealant used as the gasket on the differential housing cover. This does not indicate any previous repairs as it is used by Dana during assembly.
• 10254127Some 2023-2024 F-Super Duty/F-53 Motorhome/F-59 Commercial Stripped Chassis or 2023-2025 E-Series/F-650/F-750 vehicles equipped with a gas engine may exhibit an illuminated MIL with ignition system DTC(s) P0352, P0353, P0354, P0355, P0357, P2303, P2306, P2309, P2312, P2318, P2304, P2307, P2310, P2313, P2319, and/or P2322 set in the powertrain control module (PCM). This may be due to incorrect cylinder to DTC mapping within the PCM. This means the DTCs listed may set against the incorrect cylinder. Even though the cylinder to DTC mapping is incorrect in the PCM, the presence of these DTCs means that a real ignition system concern is present that requires diagnosis and repair. Prior to performing a pinpoint test for one of the listed DTCs, it will be necessary to identify the correct cylinder that has the issue. Do this by using the Ford diagnosis and repair system (FDRS) to perform a cylinder power balance test. If the results show two cylinders dropping out, begin diagnosing the ignition system components for the cylinder that is dropping out and not setting an ignition related DTC. Due to the incorrect incorrectcylinder to DTC mapping, the PCM will shut off fuel to the cylinder that the PCM has triggered a DTC against. Diagnosing the cylinder that does not set an ignition DTCand drops during the power balance test, will verify the identity of the cylinder that has the concern. If only onecylinder is dropping out, start diagnostics with that cylinder. Refer to the Workshop Manual, Section 303-07A/C.
• 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
• 10249790The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.

Every Ford E-350 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.