2020 Mazda MAZDA6

Owner complaints

What owners report most

1. Engine1
2. Service brakes1
3. Structure1

Latest complaints

• Feb 20, 2023CA
  Engine · Service brakes

  Uneven premature brake wear. Right front and right rear pads and rotors worn beyond limits in 28,000miles of lite freeway driving. Left front and Left rear only half worn. Engine has multiple oil leaks.

• Nov 27, 2020KS2,000 mi
  Structure › Body

  Excessive paint chipping. I have the soul red (V46) paint. it was purchased on 06jun2020 and has only 2,000 miles but it has 3 large chips. most of the miles are just going to the store. I work from home so I don't drive but a couple days a week.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
• 11011137On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.
• 11011136CSP11 - COOLANT LEAKS AT CYLINDER HEAD WARRANTY EXTENSION For certain 2019-2020MY CX-5, 2016-2020MY CX-9, 2018-2020MY Mazda6 that are equipped with SKYACTIV-G 2.5T engine, the warranty coverage for specific repair of the coolant leak at cylinder head is extended to: 10 years (120 months) or 120,000 miles (192,000 km) whichever comes first, from the original warranty start date CONDITION OF CONCERN On certain subject vehicles, the coolant may leak at the cylinder head around the exhaust manifold.
• 11011134Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head.
• 11011133Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.
• 11009665Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.
• 11009664Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.
• 11009661Please review the entire Dealer Email below announced on October 17, 2024 for full details regarding this campaign. Warranty Information is at the bottom of the TSB Parts and Warranty information and Repair Procedures will be available by October 25, 2024. Until that time if a vehicle is presented to your dealer with a complaint and CSP11 is visible in eMDCS, please click here and follow instructions in TSB 01-002/23 COOLANT LEAKS AT CYLINDER HEAD and hold claims until the Parts and Warranty Information is available in eMDCS and MGSS.
• 11009660Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.
• 11009659Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.
• 11009658Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.
• 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
• 11009647A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. Hotline and MASH authorization is not required to order parts for performing this repair. If there are any questions on part ordering or part status, contact the Dealer Assistance Group.
• 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11008577Some customers may complain about scratches on the instrument cluster lens.
• 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
• 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
• 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
• 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
• 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11006998Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
• 11006981Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.
• 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11005551At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.
• 11005550Some vehicles may experience the seat ventilation system still on after the engine has been turned off, in some cases this causes the battery to be completely discharged and not rechargeable. This is caused by a deterioration in the seat ventilation control unit. To eliminate this concern, the material for the circuit of the seat ventilation control unit has been modified.
• 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11003358A new repair procedure has been developed to address DTC P0126:00 on SKYACTIV-G 2.0/2.5L engines (non-turbo). Mazda has introduced a replacement kit of the thermostat located within the Coolant Control Valve (CCV). NOTE: It is no longer necessary to replace the CCV for this DTC.
• 11003353Some vehicles may exhibit oil seepage or oil leak onto the engine front cover, which becomes more apparent with dust adhesion.
• 11003351Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
• 11003350Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
• 11003349Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
• 11000785The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
• 11000775There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 11000772Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
• 11000355Some vehicles may have the check engine light on with DTC P0524:00 or P055F:00 stored in memory. Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and improper oil pressure.

Every Mazda MAZDA6 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.