2009 Toyota Prius
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › Prius › 2009
These records cover every 2009 Toyota Prius. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
6 recalls name the 2009 Toyota Prius. Newest first.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013…
Risk and remedy
Risk
If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy
Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Toyota is recalling certain model year 2004-2009 Prius vehicles manufactured August 6, 2003, through March 30, 2009 and FCHV-adv vehicles manufactured December 12, 2008, through September 13, 2011. During manufacturing, a scratch may have occurred inside of the electrically driven water pump at the coil wire. The coil wire may corrode at the scratched…
Risk and remedy
Risk
The corroded coil wire may break and the water pump could stop. The corroded coil wire could cause a short circuit between coil wires and a possible open fuse, creating a stall-like condition of the hybrid system while the vehicle is being driven. This may increase the risk of a vehicle crash.
Remedy
Toyota will notify its owners, and dealers will replace the electric water pump, free of charge. The recall began on January 17, 2013. Owners may contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331.
Toyota is recalling certain model year 2004-2009 Prius vehicles manufactured August 5, 2003, through March 30, 2009. The affected vehicles have a steering intermediate extension shaft assembly built with metal splines that complete the connection from the steering wheel to the steering gear. These splines may have been manufactured with an insufficient…
Risk and remedy
Risk
Over time, the splines may wear and eventually fail resulting in a loss of steering ability, increasing the risk of a vehicle crash.
Remedy
Toyota will notify owners, and dealers will inspect the extension shaft and replace it if it is one with insufficient hardness, free of charge. The recall began during December 2012. Owners may contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331.
Gulf states toyota IS recalling certain model year 2005-2010 vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold between september 1, 2005 and june 2, 2008 without the requisite load carrying capacity modification labels.
Risk and remedy
Risk
This does not meet the standard requirements.
Remedy
Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. Dealers will also correct the owner's manual. the safety recall began on may 27, 2010. owners may contact gulf states toyota at 713-580-3300.
Southeast toyota IS recalling certain model year 2005-2011 passenger vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold without the requisite load carrying capacity modification labels.
Risk and remedy
Risk
A driver may overload a vehicle which may increase the risk of a crash.
Remedy
Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. the safety recall began on may 27, 2010. owners may contact southeast toyota at 1-800-301-6859.
Toyota IS recalling certain model year 2004-2010 passenger vehicles. the accelerator pedal can get stuck in the wide open position due to its being trapped by an unsecured or incompatible driver's floor mat.
Risk and remedy
Risk
A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death.
Remedy
Toyota filed an amended defect report on november 25, 2009, stating that dealers will modify the accelerator pedal and, on certain vehicles, alter the shape of the floor surface under the pedal. these changes address the risk of pedal entrapment due to interference with the floor mat. redesigned accelerator pedals will become available beginning in april 2010 and dealers will replace any modified pedal with the new pedal if desired. also, dealers will replace any genuine toyota or lexus all-weather floor mats with redesigned all-weather mats, or repurchase the previous mats from owners who do not want the new ones. additionally, software modifications will be installed on camry, avalon and lexus ES 350, IS 350 and IS 250 models that will ensure that the brake overrides the accelerator in the event both brake and accelerator pedals are applied. toyota will begin mailing letters to owners on december 31, 2009. owners may contact toyota at 1-800-331-4331, lexus at 1-800-255-3987.
Owner complaints
502 complaints64 involved a crash4 involved a fire27 injuries2 deaths
What owners report most
Latest complaints
- Forward collision avoidance › Automatic emergency braking · Service brakes · Unknown or other
Dashboard Warning Lights: ABS, VSC, Parking Brake Light, Triangle with Exclamation Point, Codes: C1256 & C1391, Intermittent Audible Cabin Buzzing indicating critical pressure loss on start-up for about 10 seconds...then stops, not loss so much as anti-braking quick bursts at about 5 mph of…
Dashboard Warning Lights: ABS, VSC, Parking Brake Light, Triangle with Exclamation Point, Codes: C1256 & C1391, Intermittent Audible Cabin Buzzing indicating critical pressure loss on start-up for about 10 seconds...then stops, not loss so much as anti-braking quick bursts at about 5 mph of stopping v slowly and seamlessly coming to a stop. I contacted Toyota Corporate Case Management; they refused to escalate or remediate the issue due to vehicle mileage, despite being notified of the active brake pressure leak codes and the audible safety alarm.
- Service brakes
I own 2 2009 Toyota Prius. Both cars less than 175,000 miles and both have failed ABS modules. The ABS module in this vehicle is also the power brake booster. This failure can cause braking issues such as loss of braking or sudden brake application. Only known fix is replacement of the ABS brake module which requires the Toyota Techstream service computer.
- Forward collision avoidance › Automatic emergency braking · Service brakes
Brake actuator is broken. Toyota knew about this problem and they had a warranty for 10 years or 150k miles. Mine only has 80k miles. The repair is half of what the car is worth. I thought a Toyota with such low miles would be dependable. Toyota knew that people have died from this problem with…
Brake actuator is broken. Toyota knew about this problem and they had a warranty for 10 years or 150k miles. Mine only has 80k miles. The repair is half of what the car is worth. I thought a Toyota with such low miles would be dependable. Toyota knew that people have died from this problem with their car. I need this car to get to work and get my kids to school. It’s older than 10 years so I am just screwed on something they knew was broken. Of course the sales person at the Toyota dealership did not tell us about it when he sold us the car
- Service brakes, hydraulic
The contact owns a 2009 Toyota Prius. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that the ABS warning light was illuminated. The vehicle was driven to the residence. The vehicle…
The contact owns a 2009 Toyota Prius. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that the ABS warning light was illuminated. The vehicle was driven to the residence. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The dealer was made aware of the failure. The contact was informed that the extended warranty had expired. The manufacturer was made aware of the failure, and a case was filed. The contact was informed that the extended warranty had expired. The failure mileage was approximately 174,000.
- Unknown or other
Cooling system
- Service brakes
The brake actuator is failing. It’s making unusual noises when stepping on the brakes. A new additional noise started in the last month which is the pump connected to the brake actuator. The technician told me the brakes are about to fail. Toyota used to cover this issue but stopped a few years ago. It’s a $3,000.00 job at the dealer.
- Electrical system · Engine · Forward collision avoidance › Automatic emergency braking
Breaking system failure do to ASB Actuator, breaks are locking and vehicle is engine braking.
- Unknown or other · Vehicle speed control
When I am coming to a stop or need to put on my brakes my car will accelerate at a jump ahead pace As if to take off instead of slowing down and stopping. Regardless whether I’m turning a corner or I’m continuing straight when I have to Put on the brakes it speeds up instead.
- Electrical system › Instrument cluster/panel · Service brakes, hydraulic
The contact owns a 2009 Toyota Prius. The contact stated that while driving at an undisclosed speed, extra effort was needed to stop the vehicle while depressing the brake pedal. In addition, the contact stated that the instrument panel intermittently went blank and failed to operate as needed. The…
The contact owns a 2009 Toyota Prius. The contact stated that while driving at an undisclosed speed, extra effort was needed to stop the vehicle while depressing the brake pedal. In addition, the contact stated that the instrument panel intermittently went blank and failed to operate as needed. The vehicle was taken to an independent mechanic where the contact was informed that the ABS and the instrument cluster needed to be replaced. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 157,000.
- Forward collision avoidance › Automatic emergency braking · Service brakes · Unknown or other
In the 2009 Toyota Series II vehicle there are two parts for the brake actuator pump assembly which has been cycling about every 20 seconds for the past six months or more. There is an intermittent tone when depressing the brake pedal before starting the car (engine off). The Brake dash warning…
In the 2009 Toyota Series II vehicle there are two parts for the brake actuator pump assembly which has been cycling about every 20 seconds for the past six months or more. There is an intermittent tone when depressing the brake pedal before starting the car (engine off). The Brake dash warning light is on continuously. Occasional loss of brake power in reverse causing the driver to re-apply the brakes to stop unwanted motion of the vehicle.
- Service brakes
My dashboard brake, tire pressure, vsc and AB’s light came on while driving
- Service brakes
Failed brake actuator. Toyota knows about the issue and refuses to honor any reasonable repair. Braking at any speed the car ferociously pulls to the left, throwing you into another lane or on coming traffic.
- Engine · Forward collision avoidance › Automatic emergency braking · Service brakes
The engine light went on while driving on the highway. We immediately pulled over and had the vehicle towed to the nearest dealership. The dealership informed us that both the Brake Actuator (Toyota part TO44500-47141) and water pump (Toyota par TOG9020-47031) had failed. The car was no longer save to drive.
- Service brakes
Car Mechanics say I need a new ABS actuator/pump costing about $4,400 at dealership and over $2500 at garages. Most quoting about $3500.00. It is a known fact that this is common on Pruises, which I am now learning. I feel Toyota should be reimbursing their consumer for this unexpected charge. My…
Car Mechanics say I need a new ABS actuator/pump costing about $4,400 at dealership and over $2500 at garages. Most quoting about $3500.00. It is a known fact that this is common on Pruises, which I am now learning. I feel Toyota should be reimbursing their consumer for this unexpected charge. My car has only about 60000 miles on the car. RIght now I have to park the car until I come up with the money. So have no invoice to attach until I do the repair.
- Electrical system
The contact owns a 2009 Toyota Prius. The contact stated that the instrument cluster was intermittently inoperable. The contact stated that the failure had been recurring increasingly. Additionally, the contact stated that the vehicle would fail to start or to turn off intermittently while pressing…
The contact owns a 2009 Toyota Prius. The contact stated that the instrument cluster was intermittently inoperable. The contact stated that the failure had been recurring increasingly. Additionally, the contact stated that the vehicle would fail to start or to turn off intermittently while pressing the Push to Start button. The contact stated that the vehicle would respond as needed after several attempts. The vehicle was taken to an independent mechanic, where it was diagnosed that the instrument panel combination meter had failed and needed to be replaced. The mechanic related the failure to Toyota Campaign Number: ZTV and referred the contact to the dealer for the repair. The dealer was contacted and informed the contact that the repair could not be covered under Toyota Campaign Number: ZTV. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 167,532.
- Service brakes
The contact owns a 2009 Toyota Prius. The contact stated that while driving at an undisclosed speed, several unknown warning lights illuminated. Additionally, the contact depressed the brake pedal however, the brakes did not function as needed. The vehicle was driven to the residence. The dealer…
The contact owns a 2009 Toyota Prius. The contact stated that while driving at an undisclosed speed, several unknown warning lights illuminated. Additionally, the contact depressed the brake pedal however, the brakes did not function as needed. The vehicle was driven to the residence. The dealer was contacted and made aware of the failure. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure however, the contact was informed that the failure was like an unknown recall; however, the recall notification had expired. The contact was advised to report the failure to the NHTSA Hotline. The failure mileage was approximately 116,000.
- Service brakes
Losing all breaking from abs dealership says $3000 to replace abs brake actuator module. I have been hearing from other second generation owners this is a common problem and it vecomes unsafe when you lose brake functioning in traffic additionally it was an extended warranty twice with no milage…
Losing all breaking from abs dealership says $3000 to replace abs brake actuator module. I have been hearing from other second generation owners this is a common problem and it vecomes unsafe when you lose brake functioning in traffic additionally it was an extended warranty twice with no milage limitations but wondering why itvwasntvrecalled. Now I fear driving because u safe yet I am unable to afford to make the repair because I am unable to worker as delivery driver is my employment to generate income needed for repair.
- Service brakes
ABs Light came on high pitched sound and brakes suddenly stopped working while driving making very unsafe driving conditions. i recently purchased this car as my second, 2nd generation prius but the abs recall was evidently not performed when it was recalled and extended. this puts me upside down…
ABs Light came on high pitched sound and brakes suddenly stopped working while driving making very unsafe driving conditions. i recently purchased this car as my second, 2nd generation prius but the abs recall was evidently not performed when it was recalled and extended. this puts me upside down in a loan because i have found the repairs will be $1000-$2000 and now I can not afford to drive it. the car is at my home and available for inspection upon request. i felt very unsafe last night and the abs light recently came on and was intermittently making the high pitch sound which was continuous last evening when i was driving when the brakes stopped functioning
- Exterior lighting
Apparently a known issue with the HID lights coming on or off intermittently.
- Exterior lighting
The front lights and break lights sometimes turn off while I am driving. Both of the lights or one of them.
- Service brakes, air › Antilock › Abs warning light
The contact owns a 2009 Toyota Prius. The contact stated while driving at approximately 65–70 MPH, the ABS warning light illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the brake pump actuator needed to be replaced. The vehicle was not repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 236,425.
- Electrical system · Service brakes · Unknown or other
The hybrid water pump failed/ aka the inverter coolant pump. This was recalled years ago and has failed again. The previous owner of my car replaced it in 2013, so Toyota is refusing to replace it again, despite the fact that the part is faulty and has compromised the safety of my vehicle. This…
The hybrid water pump failed/ aka the inverter coolant pump. This was recalled years ago and has failed again. The previous owner of my car replaced it in 2013, so Toyota is refusing to replace it again, despite the fact that the part is faulty and has compromised the safety of my vehicle. This issue was diagnosed by a mechanic yesterday, error code P0A93. The master warning light, check engine light, brake light came on. The AC stopped working. The brakes nearly gave out on me driving on a bridge in New York City. This part was recalled. Toyota refuses to honor the recall a second time. They clearly did not properly engineer this part! It failed again! They should be responsible for fixing this issue.
- Service brakes · Wheels
All dashboard lights up. The brake fluid is full and the pads are in proper shape. When braking the car slips a few feets and I was about to make accedents several times with my school children.
- Steering
I was driving the 2009 Prius to my storage unit there was a car that I needed to go around so i sifted into reverse when I noticed a scraping sound as I was backing when I shifted into forward the sound again was there is when i noticed I had no directional control of the vehicle steering wheel…
I was driving the 2009 Prius to my storage unit there was a car that I needed to go around so i sifted into reverse when I noticed a scraping sound as I was backing when I shifted into forward the sound again was there is when i noticed I had no directional control of the vehicle steering wheel would turn but the tires would not respond at all. I called for a tow truck, I called think of a greater safety issue than driving a car with no control over where it goes.
- Service brakes
Unknown
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Pedestrian alert sounds
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
- Intermediate Steering Shaft Separation
The Office of Defects Investigation (ODI) received a January 2013 defect petition requesting that it open an investigation on Model Year (MY) 2004-2009 Toyota Prius vehicles to address a possible manufacturing safety defect related to the steering column intermediate shaft.During the defect petition evaluation, ODI…
The Office of Defects Investigation (ODI) received a January 2013 defect petition requesting that it open an investigation on Model Year (MY) 2004-2009 Toyota Prius vehicles to address a possible manufacturing safety defect related to the steering column intermediate shaft.During the defect petition evaluation, ODI: 1.Reviewed the petition and its enclosures; 2.Reviewed the subject steering system layout; 3.Examined the Petition Vehicle?s history, including its repair history; 4.Reviewed and followed-up potentially related consumer complaints; 5.Assessed Safety Recalls 06V-188 and 12V-537; and, 6.Requested and examined complaint, claim, field report, service history, and warranty information from Toyota.ODI's review revealed that the petition vehicle had been recalled (Recall 06V188) to remedy a defect in the system identified in the petition with the remedy taking place prior to the failure that prompted the petition. Circumstances point to incorrect reassembly of the petitioner's vehicle by those who performed the recall remedy.ODI examined the issues raised by this petition to identify any related safety defect trend in the general subject vehicle population.That review identified a low rate of related consumer complaints (twenty-five over a eight year period from a population of over 600,000 vehicles) and no pattern that would identify either a safety defect not already covered by the two existing steering safety recalls by Toyota or a systematic problem with either recall remedy.Based on this evaluation, ODI does not believe that additional investigation will lead to a finding that a defect related to motor vehicle safety exists in the subject vehicles. Therefore, in view of the need to allocate and prioritize NHTSA?s limited resources to best accomplish the agency's safety mission, the petition is denied. The denial of this petition does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take further action if warranted by the circumstances.For more information, see the Federal Register notice in the public file for this action (https://www.nhtsa.gov/recalls#vehicle, select NHTSA ID, enter: DP13001)The ODI reports cited above can be reviewed on-line (https://www.nhtsa.gov/recalls#vehicle) under the following NHTSA ID numbers:10407520, 10418710, 10429551, 10473654, 10478195, 10478053, 10437229, 10489425, 10510722, 10639984, 10648277, 10499778, 10712626, 10723196, 10787530, 10808124, 10838803, 11071646, 11098144, 11099507, 11102659, 11160767, 11192607, 11287550, 11287606
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
- 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
- 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
- 10230369DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10230368DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10230367DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
- 10227920DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10227919DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10227918DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
- 10227916DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 10227915TI: TECHNICAL INSTRUCTIONS Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
- 10227914CSP: Customer Support Program ZKG ? Paint Repair Process
- 10227913DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 10227912DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 10227898TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10224101DL: ZTN Expired on June 1, 2022
- 10220176DL: ZTN Expired on June 1, 2022
- 10220174TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
- 10214323TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
- 10213902TSB: This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger
- 10210376OBSOLETE NOTICE Month 09, 2022: This bulletin is now obsolete. Please see T-SB-0014-22.
Every Toyota Prius model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.