2011 Chrysler Town And Country
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Chrysler › Town And Country › 2011
These records cover every 2011 Chrysler Town And Country. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2011 Chrysler Town And Country. Newest first.
Rollx Vans (Rollx) is recalling certain GMC Yukon, Sierra, Chevrolet Express 2500, Ford Transit, E-250, Toyota Sienna, Sienna Hybrid, Honda Odyssey, Chrysler Town and Country, Voyager, Pacifica, Dodge Grand Caravan, and Ram Promaster vehicles equipped with QRT-Deluxe and QRT-Max wheelchair restraints. Please refer to Rollx's recall report for specific model…
Risk and remedy
Risk
An unsecured wheelchair can move during transit, increasing the risk of injury.
Remedy
Rollx will work with Q'Straint to inspect and replace the retractors as necessary, free of charge. Owner notification letters were mailed February 5, 2026. Owners may contact Rollx's customer service at 1-800-956-6668.
Chrysler Group, LLC (Chrysler) is recalling certain model year 2010-2014 Chrysler Town and Country and Dodge Grand Caravan vehicles manufactured August 25, 2010, through October 31, 2013. The affected vehicles may experience overheating of the vent window switch in the driver's door armrest.
Risk and remedy
Risk
An overheated switch may result in a vehicle fire.
Remedy
Chrysler will notify owners, and dealers will replace the vent window switch with a newer version, free of charge. The owner notification letter was issued and the remedy campaign launched on on December 31, 2014. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P25.
Chrysler IS recalling certain model year 2011dodge journey, jeep wrangler, chrysler 200, chrysler 200 convertible, dodge avenger, dodge nitro, jeep liberty, dodge caliber, jeep compass, jeep patriot, dodge grand caravan and chrysler town & country vehicles. some of these vehicles may have been built with a missing or incorrectly installed steering column…
Risk and remedy
Risk
A missing or incorrectly installed rivet could compromise the ability of the steering column to support the occupant loads in the event of a frontal crash, decreasing the effectiveness of the frontal impact safety system. as a result, the condition may increase the potential for injury in a frontal crash.
Remedy
Dealers will inspect for rivet presence and alignment and repair the steering column pivot as required, free of charge. the safety recall began on july 4, 2011. owners may contact chrysler at 1-800-853-1403.
Owner complaints
773 complaints10 involved a crash12 involved a fire20 injuries
What owners report most
Latest complaints
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2011 Chrysler Town and Country. The contact stated that the vehicle was purchased from the Facebook Marketplace. The vehicle was taken to the DMV to be titled, and it was discovered that the title had been altered. The odometer reading was scratched off the…
Odometer Fraud. The contact purchased a 2011 Chrysler Town and Country. The contact stated that the vehicle was purchased from the Facebook Marketplace. The vehicle was taken to the DMV to be titled, and it was discovered that the title had been altered. The odometer reading was scratched off the title, and the numbers were unidentifiable. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 101,211, and at the time of registration, it was discovered that the mileage was unknown. The contact had not retrieved a Carfax report.
- Fuel/propulsion system
The tipm fuel pump relay is faulty causing the car to start intermittently. It also stalled on a main road without any warning with my kids in the car. Luckily I was able to put the flashers on and drift to the side and others were able to get around without any accident. However they came close…
The tipm fuel pump relay is faulty causing the car to start intermittently. It also stalled on a main road without any warning with my kids in the car. Luckily I was able to put the flashers on and drift to the side and others were able to get around without any accident. However they came close to hitting myself and others. I have spent over $1,000 at this point fixing items that didn't need to be fixed only to finally find out online that others have this issue and its a known issue for Dodge, Jeep, and Chrysler Town and Country but for some reason the recall is only for Dodge and Jeep.
- Electrical system · Engine · Fuel/propulsion system
It stalls to turn on even when I changed everything from, fuel pump, fuel pump relay, heater pumps, alternator, new battery. And it still won’t turn on it’s been happening for 4 months now. And I changed things that were recommended. I do my oil change every time I need as well.
- Service brakes, hydraulic
The contact owns a 2011 Chrysler Town and Country. The contact stated that while attempting to start the vehicle, the ABS module and Service Brake warning lights illuminated. The contact stated that the gear shift indicator also failed to operate as needed. A dealer was contacted. The vehicle was…
The contact owns a 2011 Chrysler Town and Country. The contact stated that while attempting to start the vehicle, the ABS module and Service Brake warning lights illuminated. The contact stated that the gear shift indicator also failed to operate as needed. A dealer was contacted. The vehicle was taken to a dealer, where it was diagnosed and determined that the ABS and traction control had failed, and the ABS module needed to be replaced. The ABS module was replaced. The manufacturer was not notified of the failure. The approximate failure mileage was 86,000.
- Electrical system
The contact owns a 2011 Chrysler Town and Country. The contact stated while at a complete stop on several occasions, the vehicle stalled. The vehicle was able to restart on some occasions; however, the vehicle failed to restart on other occasions and was towed. The vehicle was taken to the dealer…
The contact owns a 2011 Chrysler Town and Country. The contact stated while at a complete stop on several occasions, the vehicle stalled. The vehicle was able to restart on some occasions; however, the vehicle failed to restart on other occasions and was towed. The vehicle was taken to the dealer several times; however, the failure could not be duplicated. The contact stated that the failure persisted, and the contact was able to start the vehicle with the index finger. The dealer was contacted and informed the contact that the failure could be related to the WIN module. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 129,010.
- Engine
My vehicle has overheating problems ever since I have had it. I have had the thermostat replaced. The sensor thermostat replaced. The radiator flushed and had several shops look at it yet they could find nothing wrong but I go through antifreeze like crazy. At least 1 gallon every month. The temp reads 100 - 180 on hot days and it gets super hot.
- Electrical system · Visibility/wiper
In Oct of 2024 My driver's side window shattered out of nowhere for no apparent reason! I heard this really loud boom then the window shattered ! I took it in the have the regulator replaced and the window. I also put a windshield in it at that time as well. Then in August of 2025 not even a year…
In Oct of 2024 My driver's side window shattered out of nowhere for no apparent reason! I heard this really loud boom then the window shattered ! I took it in the have the regulator replaced and the window. I also put a windshield in it at that time as well. Then in August of 2025 not even a year later and once again my window shattered and my winshield cracked. This time i was driving on the freeway and I heard a big pop the crash and in tiny pieces mof glass fell in to the door driver's side window .
- Engine
The vehicle had a recall that was not satisfied before expiration. The vehicle currently has only 92,135 miles. The car would stall out while driving down the road. The head was manufactured to thin, cylinder misfire. It was very unsafe going up and down the mountains in our area especially.…
The vehicle had a recall that was not satisfied before expiration. The vehicle currently has only 92,135 miles. The car would stall out while driving down the road. The head was manufactured to thin, cylinder misfire. It was very unsafe going up and down the mountains in our area especially. It would not shift after going down an incline. So have to pull over and restart. I called and made a complaint before. We finally saved up enough to pay for the work. I have a receipt for $3219.76. The chrysler recall bulletin is 09-002-14. I contacted Chrysler they just put me to all different people and no one knows. This was a very dangerous situation to drive.
- Engine
The contact owns a 2011 Chrysler Town and Country. The contact stated while driving at various speeds, the vehicle stalled with the check engine warning light illuminated. The vehicle was restarted after a while. The vehicle was taken to Holcombe Automotive, where it was determined that one of the…
The contact owns a 2011 Chrysler Town and Country. The contact stated while driving at various speeds, the vehicle stalled with the check engine warning light illuminated. The vehicle was restarted after a while. The vehicle was taken to Holcombe Automotive, where it was determined that one of the cylinder heads needed to be replaced. The vehicle was not repaired. The dealer was notified of the failure and referred the contact to the manufacturer for assistance. The manufacturer was notified of the failure and informed the contact that the vehicle could not be repaired under TSB Number: D-14-12 because the TSB had expired. The failure mileage was approximately 77,564.
- Engine and engine cooling · Steering · Structure
The contact owns a 2011 Chrysler Town and Country. The contact stated that while her husband was driving at an undisclosed speed, the window glass fell into the door abruptly. A mechanic inspected the vehicle and determined that the failure occurred due to an internal door fracture. The vehicle was…
The contact owns a 2011 Chrysler Town and Country. The contact stated that while her husband was driving at an undisclosed speed, the window glass fell into the door abruptly. A mechanic inspected the vehicle and determined that the failure occurred due to an internal door fracture. The vehicle was not repaired. The contact stated while driving and turning the steering wheel, the steering wheel made an abnormally loud squealing sound. Additionally, the contact stated that the vehicle had difficulty starting, and there was an abnormal amount of smoke coming out of the exhaust pipe. The check engine warning light and the electronic throttle control warning light were illuminated. An unknown dealer was notified of the failure. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 174,098.
- Electrical system · Engine
I wrote before about the electrical issue. My husband jumped started my car On 8/28/24. I drove down to my church for a Women's Bible Study. I was there for 2 1/2 hours. When I went to leave my car would not start. I called my son. He jump started my car for me. As I was about to leave after a few…
I wrote before about the electrical issue. My husband jumped started my car On 8/28/24. I drove down to my church for a Women's Bible Study. I was there for 2 1/2 hours. When I went to leave my car would not start. I called my son. He jump started my car for me. As I was about to leave after a few minutes my car quit running. As the car was running every electrical component on the dash was going haywire, the heater fan was going full blast, but the windows would not go up. That was irritating as it started to rain. Had to cover the windows. Left the car in parking lot. Next day after church my husband tried to start the car. The car turned over and the battery light was on. Brande new battery was put in that week, As the following we thought that might have been the problem. He jumped started the car same thing as before. We had to have the car flat bedded to the mechanic. The mechanic tested the new alternator that was just put in and said it was bad. Replaced the alternator and car ran. He wanted to see what would happen so he kept car over night. Next morning car would not start. All fuses have been checked, fuse box has been checked. Nobody can seem to figure out what is going on with this vehicle. I have spent over $2000. an to no avail. I am ready to junk this thing. Mu dad said their was a Caravan for sale I just read they have electrical issues also no way.
- Electrical system · Unknown or other
Over 2 yrs now the electrical has been haywire. In driveway the interior lights on dash lights come on and and doors lock and unlock. Driving down road on dash tells you that must put car in park to engage. Lift gate ajar. Heater turns on and off full blast front and back fans. Side doors do not…
Over 2 yrs now the electrical has been haywire. In driveway the interior lights on dash lights come on and and doors lock and unlock. Driving down road on dash tells you that must put car in park to engage. Lift gate ajar. Heater turns on and off full blast front and back fans. Side doors do not work/ or work when they want to work. Battery brand new gets drained and needs to be charged 1 every month. Had alternator changed. Still does the same thing. I call this my possessed van. At my wits end. Spent much money trying to find out problem unable to locate. Changed fuses did not help. This is my second town and country. I never had a problem with my first one which was a much older model that is why I got another one. Now I am rethinking about getting another town and country. Who is going to help with all of these customer complaints with electrical issues. I am a disabled person who needs my vehicle for appointments. I cannot get stranded or break down or have a vehicle fire. I am frustrated by this company for not caring for their customers needs.
- Exterior lighting
Headlight on passenger side went out and it was not the bulb assembly.
- Unknown or other
Unknown what part is at fault. The automatic sliding doors will open fully and then immediately close. The feature that is supposed to make the doors stop when they detect something does not activate. An adult's full body weight is needed to press on the door to make it stop closing. Faulty on both…
Unknown what part is at fault. The automatic sliding doors will open fully and then immediately close. The feature that is supposed to make the doors stop when they detect something does not activate. An adult's full body weight is needed to press on the door to make it stop closing. Faulty on both driver and passenger sides. Starts to happen intermittently and then constantly. Dealership claims it is a "software" issue and not applicable for bumper-to-bumper warranty. I also contacted the mopar warranty department and they also claim it is not a covered issue even though there is a serious safety risk involved. A quick google search reveals it is a common problem.
- Electrical system
2011 Town and Country started stalling while driving up to 40mph! The problem is intermitten and unable to be diagnosed by mechanic. This happens in the middle of traffic and power steering is lost. This is a known problem and was recalled in the several years before mine. This is a safety issue to everyone on the road and is a matter of time before there is an accident.
- Electrical system · Structure › Body
Van was sitting in driveaway in front of my house. We noticed smoke coming from rear of the vehicle and then saw flames. Contacted 911. Fire department arrived to put out the fire. They said something appeared to have shorted or exploded inside the driver side rear wall panel. Just below the rear window vent in the area of the 3 row speakers and cup holders. It burned down the exterior of the van near the gas cap.
- Electrical system · Engine
The contact owns a 2011 Chrysler Town and Country. The contact stated that while driving at 45–50 MPH, the complete electrical system shut down. There were no warning lights illuminated. The vehicle was towed to an independent mechanic, who stated that the electrical system had shut down. The…
The contact owns a 2011 Chrysler Town and Country. The contact stated that while driving at 45–50 MPH, the complete electrical system shut down. There were no warning lights illuminated. The vehicle was towed to an independent mechanic, who stated that the electrical system had shut down. The vehicle failed to turn over and restart. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred to the NHTSA hotline. The approximate failure mileage was 186,000.
- Back over prevention › Warnings · Forward collision avoidance › Automatic emergency braking · Service brakes
Vehicle is a 2011 Chrysler Town Country Touring L and has 68,000 miles on it. It is well maintained with no issues prior to compliant incident. While normal driving of vehicle emergency dash light system activated numerous safety warning lights i.e.: ABS, ESC, Engine light. My wife was travelling…
Vehicle is a 2011 Chrysler Town Country Touring L and has 68,000 miles on it. It is well maintained with no issues prior to compliant incident. While normal driving of vehicle emergency dash light system activated numerous safety warning lights i.e.: ABS, ESC, Engine light. My wife was travelling on a highway at 68 mph. Loss of drivability noted at the time included; loss of speedometer, abnormal shifting of transmission, loss of ABS and traction Control, Cruise Control and seat belt notification. The following day, I took the vehicle to repair dealership where I was notified that there was numerous codes showing up on scanner. PCM Codes included; c2200 Internal fault of ABS Module, U1110, U1120, P0501. Advised that I would lose numerous other systems not noted due to codes these included; electric rear doors inoperable while vehicle started, seat belt alarm system, rear parking system notification. Dealership advises that Chrysler company has put the sale of ABS modules part # 68089474AA on hold for over the last year, due to an Engineering review, and that no modules are available for sale. It was recommend that I "get rid of the vehicle". In doing internet searches this is a long running problem with numerous vehicles using this same ABS Module system. Due to the numerous safety systems this affects, the vehicles are unsafe without a recall to correct this manufacturer defective ABS Brake Module. I have had to setup an auxiliary GPS module to calculate speed and severely limit driving this vehicle during inclement weather. As of now normal braking remains unaffected but there. Public is at the mercy of the manufacturer as ABS modules are not for sale and have a retail value of over $1300.00 + install and dealer reprogramming. This is a severe safety issue and aligns with other current recalls of similar models with the same condition. You may contact me at anytime to discuss. I am a recently retire Chief of Police and a certified Accident Homicide Investigator.
- Electrical system
The contact owns a 2011 Chrysler Town and Country. The contact stated that the vehicle was parked at his residence in the driveway, the contact stated a friend knocked on the door and informed the contact that the vehicle was on fire. The contact stated the fire extinguished on its own. The contact…
The contact owns a 2011 Chrysler Town and Country. The contact stated that the vehicle was parked at his residence in the driveway, the contact stated a friend knocked on the door and informed the contact that the vehicle was on fire. The contact stated the fire extinguished on its own. The contact stated no fire or police report was filed. The contact stated that the fire seemed to have started on the driver's side of the vehicle and in between the second and third row of seats. The contact stated that he contacted the dealer to make them aware of the failure and was advised to bring the vehicle to the repair center. The vehicle was taken to the dealer. The manufacturer representative inspected the vehicle and advised the contact that the fire was not caused due to faulty Chrysler parts. The fire origin was unknown. The manufacturer was made aware of the failure. The failure mileage was approximately 150,000. The VIN was not available.
- Service brakes · Unknown or other · Vehicle speed control
The ABS light, Traction light, and Brake light all come on and simultaneously. I've been told that the ABS Module is bad and needs to be replaced. The fact that the module needs to be replaced concerns me since there are prior recalls for ABS Module with other Dodge, Ram, and Chrsyler makes and models.
- Air bags · Seat belts · Seats
On 4/9/12 I was involved in a serious accident that resulted in my daughter obtaining a severe traumatic brain. She was in critical condition and is now severely disabled. The back curtain airbags did not protect her and did not appear to work properly. I believe that the vehicle was not properly…
On 4/9/12 I was involved in a serious accident that resulted in my daughter obtaining a severe traumatic brain. She was in critical condition and is now severely disabled. The back curtain airbags did not protect her and did not appear to work properly. I believe that the vehicle was not properly examined after the accident. The car was a rental vehicle and my family was out of state on vacation. Due to the severe injury of my daughter I believe that the airbags failed.
- Service brakes
The contact owns a 2011 Chrysler Town and Country. The contact stated that while merging at an undisclosed speed, he attempted to slow the vehicle by applying the brake pedal, which failed to slow the vehicle rapidly enough to avoid a collision. As a result, the contact collided with the vehicle in…
The contact owns a 2011 Chrysler Town and Country. The contact stated that while merging at an undisclosed speed, he attempted to slow the vehicle by applying the brake pedal, which failed to slow the vehicle rapidly enough to avoid a collision. As a result, the contact collided with the vehicle in front of him. The air bags did not deploy. No warning lights were displayed on the instrument panel. A police report was filed. No injuries were reported. The vehicle was not taken to the dealer or an independent mechanic. The manufacturer was notified, but a case was not opened; the contact stated that he informed the manufacturer of intermittent brake failure as he had experienced similar events on undisclosed dates. The failure mileage was 52,000.
- Electrical system · Fuel/propulsion system · Vehicle speed control
The van has a problem accelerating and also seems to stall while driving on the expressway before jumping quickly into acceleration there was a bad storm in Buffalo that I believe contributed to the problems of the Chrysler van
- Electrical system · Engine · Fuel/propulsion system
During random times; starting cold, starting warm, coming to a stop, accelarating, on city surface streets or on the freeway, after long drives or just going down the street; the minivan would stall and not restart. Fortunately able to coast to side of road on occassion. Non start condition would…
During random times; starting cold, starting warm, coming to a stop, accelarating, on city surface streets or on the freeway, after long drives or just going down the street; the minivan would stall and not restart. Fortunately able to coast to side of road on occassion. Non start condition would last between 15 minutes to days. This last event occured while turning in a busy intersection. Blocked cars and buses in all four directions on a Friday afternoon rush hour, putting ourselves and others at serious risk. There were no warning lights or anything other than a brief shudder before stalling. Roadside service called 911 first to get us out of the way. Towed to local mechanic who duplicated event and found that two separate recalls for faulty fuel pump relay was issued for other models but not our minivan. This family vehicle is now a liability if the fuel pump relay replacement is not made available to us.
- Engine · Fuel/propulsion system
The fuel pump is sporadically not getting power. This has left me stranded multiple times. I’m worried that this could happen while driving on the interstate and causing an accident.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Active Head Rest Inadvertent Deployment
The Office of Defects Investigation (ODI) opened PE19014 on September 9, 2019, to investigate 128 consumer complaints alleging that the Active Head Rest (AHR) inadvertently deployed without the occurrence of a crash or other rear impact event in model year (MY) 2014 Jeep Grand Cherokee and Dodge Durango vehicles.When…
The Office of Defects Investigation (ODI) opened PE19014 on September 9, 2019, to investigate 128 consumer complaints alleging that the Active Head Rest (AHR) inadvertently deployed without the occurrence of a crash or other rear impact event in model year (MY) 2014 Jeep Grand Cherokee and Dodge Durango vehicles.When ODI opened the investigation, ODI was aware of thirteen alleged injuries.A small number of Early Warning Reports identified driver and/or passenger front seat AHR inadvertent deployments without a rear impact event.Reported safety consequences resulting from the AHR deployments include concussions, headaches, soft tissue injuries, disorientation, nausea, vomiting and/or loss of vehicle control as a result of being surprised and distracted by being struck in the head by the inadvertent AHR deployment. On September 24, 2019, ODI sent an Information Request (IR) letter to Fiat Chrysler Automobiles (FCA).ODI requested certain detailed information from FCA related to the following subject vehicles: MY 2010-2014 Dodge Avenger 200, MY 2010-2014 Dodge Calber, MY 2010-2014 Chrysler Sebring, MY 2013-2015 Ram Tradesman, MY 2012 Ram Van, MY 2010-2019 Dodge Grand Caravan, MY 2010-2016 Chrysler Town and Country, MY 2010-2017 Jeep Compass, MY 2011-2020 Dodge Durango, MY 2011-2020 Jeep Grand Cherokee, MY 2010-2019 Dodge Journey, MY 2010-2012 Jeep Liberty, MY 2010-2011 Jeep Nitro, and MY 2010-2011 Jeep Patriot vehicles.On December 2, 2019, ODI received a response from FCA that included vehicle production data, consumer complaints, field reports, warranty claims, manufacturer actions, production changes, and other data related to the alleged defect from the start of production (2010) through September 24, 2019.On January 27, 2020, ODI received an update to the December 2, 2019, IR response from FCA.On September 22, 2020, ODI requested additional subject vehicle AHR information from FCA.ODI received FCA's response on October 21, 2020.ODI subsequently received an update to FCA's October 21, 2020, response on February 16, 2021.During the investigation, ODI requested updates to certain IR questions on two occasions.FCA provided updates to question #2 on March 5, 2021, and questions #2 and #5 on May 26, 2023. FCA’s IR response data identified approximately 7.5 million subject vehicles (with approximately 15 million AHR assemblies).Due to the large number of vehicles and failure reports, ODI focused its analysis on the FCA vehicle model with the highest failure rate to represent the worst-case scenario.For this purpose, ODI focused on MY 2012-2015 Jeep Grand Cherokee vehicles for its analysis.This population includes 710,890 vehicles that FCA manufactured between August 19, 2011, and August 8, 2015.ODI identified 2,839 alleged AHR failures within this limited population.ODI identified 263 alleged injuries that were caused by AHR failures in MY 2012-2015 Grand Cherokees vehicles.Of these alleged injuries, ODI categorized them as eighty-two (82) soft tissue (neck/whiplash, bruise) injuries, four (4) concussions, fifty-nine (59) headaches, and one hundred eighteen (118) without a specific injury description.Although complainants have alleged injuries, ODI has been unable to obtain evidence to substantiate or validate any injuries where medical treatment was required.Consumer outreach was conducted by ODI, where sixty-three (63) FCA complainants with alleged injuries were contacted.Twelve of the sixty-three FCA consumers responded and were interviewed by ODI.ODI requested medical records, however, only one response was provided. Attorneys representing the responding complainant provided a synopsis that indicated they had experienced prior neck-related injuries dating to the mid-1990s.ODI also contacted one hundred (100) consumers who submitted Vehicle Owner Questionnaires (VOQ) in an attempt to validate alleged injuries. Despite the efforts of ODI, the office has been unsuccessful at obtaining substantive documentation/evidence supporting complaints that allege serious injuries (where pre-existing medical conditions did not already exist). In addition to the low severity of alleged injuries caused by AHR deployments, there have been eleven alleged crashes and two alleged lane departures within the entire subject vehicle population that has been in the field up to sixteen years (with over 8,500 AHR inadvertent deployments).ODI was not able to validate that the alleged crashes were the result of inadvertent head rest deployments, and the crashes were minor in nature. ODI has conducted a thorough investigation of the alleged safety defect and with up to sixteen years of exposure for some vehicles and over 8,500 inadvertent AHR deployments, no serious crashes or injuries could be validated in the sub-population of focus.The lack of serious injuries validated by ODI with such large period of field exposure is consistent with thework done by NHTSA’s Human Injury Research Division and the Biodynamic Research Corporation, which support that an inadvertent AHR deployment is not likely to cause serious injury.In addition to the low risk of injury, FCA released an extended warranty program that covers inadvertent AHR deployment for ten years / unlimited mileage from the vehicle's in-service date. PE19014 is closed with the FCA extended warranty program.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist, and the Agency reserves the right to take additional action if warranted by new circumstances. To review a complete closing summary, please the attached closing report. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Totally Integrated Power Module Failure
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007…
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010954Incoming Vehicles with Deployed Active Head Rest (AHR) should have a through enquiry. If there is no Broken Pieces or Electrical failure, Direction to RESET the AHR following the Procedure.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10247906ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
- 10247905ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10242717Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
- 10234379ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
- 10234378ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
- 10229898Service Bulletin 08-046-14 REV. A Superseded By Customer Satisfaction Notification (CSN) P25 Refer to service procedures outlined in CSN P25.
- 10229871Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
- 10229866Setting Mode Is Selected And Headlamps Always Stay On
- 10229845HVAC System Intermittently Blows Cold Regardless of Setting
- 10229830This Bulletin involves disconnecting the switch for the rear power vent window, if requested by the customer
- 10229829Power Window-Vent Switch - Interim CSN Repair
- 10229825RHW RHP Radio Software Enhancements
- 10229572Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10229178Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10228989Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
- 10228975Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
- 10228117Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: **U0140 - Lost Communication With Body Control Module (TIPM).** P0032 - O2 Sensor 1/1 Heater Circuit High. P0038 - O2 Sensor 1/2 Heater Circuit High. P0052 - O2 Sensor 2/1 Heater Circuit High. P0058 - O2 Sensor 2/2 Heater Circuit High. P0031 - O2 Sensor 1/1 Heater Circuit Low. P0037 - O2 Sensor 1/2 Heater Circuit Low. P0051 - O2 Sensor 2/1 Heater Circuit Low. P0057 - O2 Sensor 2/2 Heater Circuit Low. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0349 - Camshaft Position Sensor Circuit Intermittent - Bank 2 Sensor 1. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0394 - Bank 2 Camshaft Position Sensor 2/2 Circuit Intermittent.
- 10228020Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
- 10227983If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
- 10225424Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10225287Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
- 10224887RES / RHA / REB Radios That Support Bluetooth and Hands-Free 1. For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands; DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Hands Free Module (and associated components) are the systems responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
- 10224693Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 10224637Hands Free Module Prompts Begin Erroneously This bulletin involves diagnosing and based on outcome, either performing a USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.
- 10224077Active Head Restraint (AHR) Inadvertent Deployment - X87 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10223028Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
- 10223014Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
- 10221831(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10221813No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle
- 10221512Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10221375Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when
- 10221231PLATE, TORQUE CONVERTER DRIVE For 3.6L with 62TE NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)
- 10221192Steering System Inspection After a Collision This bulletin documents the FCA US LLC position regarding conditions under which replacement or repair of steering system components are required.
- 10221154No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
- 1022112362TE 6-Speed Transmission Cracked Torque Converter (TC) Piston Repair Index, To Aid In Diagnosis And Repair
- 10221098Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Every Chrysler Town And Country model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.