2017 Chrysler Town And Country

Recalls

1 recall names the 2017 Chrysler Town And Country. Newest first.

• Electrical system › Wiring › Front underhood

  Aug 9, 2018NHTSA 18V52400012,779 vehicles

  Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid…

  Risk and remedy

  Risk

  A vehicle stall can increase the risk of a crash.

  Remedy

  Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010954Incoming Vehicles with Deployed Active Head Rest (AHR) should have a through enquiry. If there is no Broken Pieces or Electrical failure, Direction to RESET the AHR following the Procedure.
• 10251783Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
• 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
• 10247948Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
• 10244356LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
• 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
• 10243209FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
• 10243208Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
• 10242717Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
• 10239957Water Quality When Mixed With Engine Coolant
• 10236933wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
• 10234420Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
• 10230183No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
• 10230180Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
• 10229572Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
• 10228989Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
• 10228157Latch Sliding Door For RT ONLY: Sliding Door Latch Prior to replacing these parts for an intermittent issue or complaint of the Sliding Door does not power open or close, please inspect the Sliding Door Actuator Module and latch for fretting and oxidation corrosion at connections prior to replacing any parts.~ If concerns are found with the Module, then replace the Sliding Door Actuator Module. Otherwise replace the Sliding Door Latch. Refer to STAR parts for specific Sliding Door Actuator Module or Sliding Door Latch part number.~
• 10227983If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
• 10225424Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
• 10225287Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
• 10224894Cam Phasers, Oil Control Valve For Malfunction Indicator Light (MIL) issues related to 2012-2017 3.6L Pentastar engines, please note that there is a new diagnostic procedure available in DealerCONNECT for P-codes in relationship to cam phasers. Please use this new information for trouble shooting of cam phasers and oil control valves for MIL on issues.
• 10224885Fuel Tank and Fuel Evap System Components 1) For JK MIL On ? P0441: Before replacing this part due to fault code P0441, check for restriction due to plastic over-flash in the Purge Hose Port of the Intake Manifold. If there is flash in the Purge Hose Port of the Intake Manifold and the vehicle is 2016 MY then replace the Intake Manifold and send to QEC. Otherwise, remove the flash with a 5/32? drill bit and clean the Intake Manifold of any flash debris. If the fault code P0441 continues after repairing the Intake Manifold, then send Freeze Frame data of P0441 to Michael.Ade@FCAgroup.com and contact Sylvia Lopez at cell number (248) 520-9734. If you don`t receive response within 15 minutes, please continue with the normal repair procedure. 2) For RT MIL On ? P0456: If ESIM needs to be replaced for fault code P0456, check the Vapor Line, Fresh Air Filter and the Black Frame Rail Blocker for water ingestion. If water ingestion is found, then replace the ESIM part number 04861962AB and the Jumper, Vent Recirculation Tube part number 04721757AI. Please contact Release Engineer Alfredo Salituro @ 213-700-5359 before performing repair service. If you do not receive a response within 15 minutes, please continue with the normal repair procedure.
• 10224882Valve Cover and Gasket, Left and Right Pertains to vehicles equipped with a 3.6L V6 V.V.T. Engine only: Oil leaking from the valve cover onto the O2 sensor causing faults codes P0140, P2096, P0137, P0157. Need to verify the leak source and cause (gasket pinched, out of position, rolled, or cut). Please call one of the individuals below before proceeding with the repair. Also, if possible take a picture and send it to the emails listed below. First: Scott Knaggs - Cell (313) 363-6937 scott.knaggs@facgroup.com Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair.
• 10224693Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
• 10224681Rain light sensor Rain sense wipers do not operate: 1. Visual Inspection--> Check if the sensor is visually OK. (all the pins are OK) Check that the Connector is NOT loose (Sensor must get a voltage from 9V to 16V) 2. Functional Checks Rain--> Steering column switch is in auto mode (sensor is active) it is necessary to splash water on the sensitive surface of the sensor to trigger wipes. check the same for different sensitivities When the rain sensitivity is increased (for example from level 0 to level 1), as an acknowledgement a single wipe is seen. (This is not a phantom wipe) and this single wipe is not seen when the rain sensitivity is decreased (from higher level to lower level) Light--> Steering column switch is in auto mode (sensor is active) block the light coming on the sensor from outside of the vehicle (use a opaque object), the head lamps should be activated 3. If the sensor seems functional, it is ideal to remove the silicon gel pad from the sensor, replace it with the new silicon gel pad instead of replacing the whole sensor. When servicing the LRSM please replace the silicon gel pad with a new silicon gel pad (PN 68224945AA) instead of replacing the whole sensor.
• 10224077Active Head Restraint (AHR) Inadvertent Deployment - X87 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
• 10224023(Rev. A) Battery Tester Warranty Code Procedures, Medtronic Update Process
• 10223855Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
• 10223721Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block. Ensure the torque on the 5 (OFA) bolts are torqued to 12nm.
• 10223579Sliding Door Lock(s) Inoperative This bulletin involves replacing either one or both of the sliding door lock actuators (if necessary). The customer may describe that either one or both of the sliding door locks do not function and/or emit a loud buzzing noise during lock/unlock operation.
• 10223028Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
• 10221787USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
• 10221597No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
• 10221594Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
• 10221228WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
• 10221192Steering System Inspection After a Collision This bulletin documents the FCA US LLC position regarding conditions under which replacement or repair of steering system components are required.
• 10221153Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
• 10221152Battery Tester Warranty Code Procedures, Medtronic Update Process
• 10221150Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
• 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Every Chrysler Town And Country model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.