2007 Jeep Wrangler
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Jeep › Wrangler › 2007
These records cover every 2007 Jeep Wrangler. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
10 recalls name the 2007 Jeep Wrangler. Newest first.
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge…
Risk and remedy
Risk
These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
Chrysler (FCA US LLC) is recalling certain model year 2007-2010 Jeep Wrangler JK vehicles manufactured March 2, 2006, to August 13, 2010. The clockspring assembly may become contaminated with dust and cause the air bag circuit to fail.
Risk and remedy
Risk
Failure of the air bag circuit may prevent the driver's frontal air bag from deploying in the event of a crash, increasing the risk of injury.
Remedy
Chrysler will notify owners, and dealers will replace the clockspring, wheel back cover, and column shroud, free of charge. The recall began on December 14, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S33.
Quadratec, Inc. is recalling certain aftermarket accessory, driver-side, Ultimate Floor Liners part numbers 14254.0301 07, 14254.0301 08, 14254.0301Q, 14254.0302 07, 14254.0302 08, 14254.0302Q, 14254.0303 07, 14254.0303 08, 14254.0303Q, 14254.0309 07, 14254.0309 08, and 14254.0309Q sold from May 1, 2012, through February 14, 2013. The liners are for use in…
Risk and remedy
Risk
If the liner shifts forward it may impede the operation of the accelerator and possibly lead to unintended acceleration, which may increase the risk of a crash.
Remedy
Quadratec will notify owners and either exchange the liners or provide them with a hook guard kit to help secure the driver-side mat, free of charge. The recall began on April 4, 2013. Owners may contact Quadratec at 1-800-463-2998 or info@quadratec.com.
Chrysler IS recalling certain model year 2007 through 2010 jeep wrangler left and right hand drive passenger vehicles manufactured from may 15, 2006 through april 22, 2010. there may be contact between the right and left front inner fender liners and the right front and left rear brake tubes which could cause wear of the tubes causing a brake fluid leak.
Risk and remedy
Risk
A brake fluid leak can cause partial loss of service brakes at the affected wheel increasing the risk of a crash.
Remedy
Chrysler will notify owners and dealers will repair the vehicles free of charge. owners may contact chrysler toll-free at 1-800-853-1403.
Chrysler IS recalling certain model year 2007 through 2008 jeep wrangler vehicles manufactured from june 2006 through july 2008, equipped with automatic transmissions. these vehicles were not equipped with a transmission fluid temperature warning system.
Risk and remedy
Risk
Fluid could boil over and may come into contact with a hot engine or exhaust component and cause a fire.
Remedy
Dealers will inspect and install a "hotoil" message in the instrument cluster and a chime indicating an elevated transmission fluid condition. the recall began on february 22, 2010. owners may contact chrysler at 1-800-835-1403.
Chrysler IS recalling 308 aftermarket mopar tow bar assemblies, p/n 82209758, sold during 2007 and 2008 calendar year which are used to tow model year 2007 and 2008 jeep wrangler vehicles.
Risk and remedy
Risk
The tow bar can fail under certain driving conditions. this can result in the towed vehicle separating from the towing vehicle, possibly resulting in a crash.
Remedy
Chrysler will notify the owners of all 2007 and 2008 model year jeep wrangler vehicles who could have purchased a recalled tow bar and will replace the tow bars free of charge. the safety recall began on november 23, 2009. owners may contact chrysler at 1-800-853-1403.
Chrysler IS recalling 1,585 my 2007-2008 jeep wrangler, right hand drive only, vehicles. some vehicles may have insufficient clearance between the steering intermediate shaft and rear brake tubes.
Risk and remedy
Risk
Prolonged brake tube contact could wear a hole in the tube and cause a partial brake system loss. this could cause a crash without warning.
Remedy
Dealers will install a revised brake tube clip to retain the tubes, inspect the brake tubes for damage due to potential contact with the steering intermediate shaft, and replace the brake tubes if necessary. the recall began on june 30, 2008. owners may contact chrysler at 1-800-853-1403.
On certain sport utility vehicles, the software programmed into the ABS electronic control module may allow a momentary delay in braking when coasting up a hill during certain conditions.
Risk and remedy
Risk
This could cause a crash without warning.
Remedy
Dealers will reprogram the ABS electronic control module with new software that prevents this condition free of charge. the recall began on october 22, 2007. owners may contact chrysler at 1-800-853-1403.
On certain vehicles, the totally integrated power module (tipm) was programmed with software that may allow the engine to stall under certain operating conditions.
Risk and remedy
Risk
This could cause a crash without warning.
Remedy
Dealers will reprogram the tipm. the recall began on july 5, 2007. owners may contact daimlerchrysler at 1-800-853-1403.
On certain vehicles, the antilock brake system (ABS) control module software may cause the rear brakes to lock up during certain braking conditions.
Risk and remedy
Risk
This could result in a loss of vehicle control and cause a crash without warning.
Remedy
Dealers will reprogram the ABS electronic control unit. the recall began on february 19, 2007. owners may contact daimlerchrysler at 1-800-853-1403.
Owner complaints
558 complaints15 involved a crash25 involved a fire17 injuries
What owners report most
Latest complaints
- Air bags · Electrical system · Service brakes, hydraulic
The contact owns a 2007 Jeep Wrangler. The contact stated that while depressing the brake pedal and making a quick turn, the traction control warning light intermittently illuminated. The vehicle was taken to an independent mechanic, where the braking system was replaced. Additionally, the air bag…
The contact owns a 2007 Jeep Wrangler. The contact stated that while depressing the brake pedal and making a quick turn, the traction control warning light intermittently illuminated. The vehicle was taken to an independent mechanic, where the braking system was replaced. Additionally, the air bag warning light was intermittently illuminated. The vehicle was taken to the dealer, and the contact was informed that the VIN was not under recall. The contact was informed that the vehicle was previously repaired under recalls associated with the failures. The contact stated that the recall repairs failed to fix the vehicle. The manufacturer was notified of the failure by phone. The failure mileage was approximately 138,000.
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2007 Jeep Wrangler. It was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the mileage was 143,000; however, Carfax reported the mileage as 168,000 in 2022.
- Electrical system › Propulsion system › Fuses, relays, contacts, and shunts
The contact owns a 2007 Jeep Wrangler. The contact stated while attempting to start the vehicle, an abnormal clicking sound was heard coming from under the hood. Additionally, several unknown warning lights were illuminated. The contact replaced several fuses; however, the fuse box failed to work…
The contact owns a 2007 Jeep Wrangler. The contact stated while attempting to start the vehicle, an abnormal clicking sound was heard coming from under the hood. Additionally, several unknown warning lights were illuminated. The contact replaced several fuses; however, the fuse box failed to work as intended. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 139,500.
- Service brakes, hydraulic
The contact owns a 2007 Jeep Wrangler. The contact stated while attempting to start the vehicle, the brake pedal was depressed, however the brake pedal failed to function as intended. The contact stated that the brake pedal was depressed to the floor, and the service brakes failed to engage. The…
The contact owns a 2007 Jeep Wrangler. The contact stated while attempting to start the vehicle, the brake pedal was depressed, however the brake pedal failed to function as intended. The contact stated that the brake pedal was depressed to the floor, and the service brakes failed to engage. The contact inspected the vehicle and noticed a hole in the brake line. In addition, the brake fluid was squirting out of the brake fluid canister. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 100,000.
- Unknown or other
i was driving my truck on Saturday march 21,2026 and all of a sudden black smoke started pouring thru my heater vents. i could no longer steer the vehicle and i put into park shut it off and left the vehicle. after we got out we could see a fire under my jeep. by the time the fire department got there my jeep was a total loss.
- Air bags · Electrical system · Steering
Vehicle Information: Make: Jeep Model: Wrangler Model Year: 2007 VIN: [XXX] Safety Recall Information: NHTSA Campaign ID: 16V-290 Manufacturer Recall Number: S33 Component: Airbag / Clock Spring This recall was previously performed by a dealership in February 2021; however, the vehicle is now…
Vehicle Information: Make: Jeep Model: Wrangler Model Year: 2007 VIN: [XXX] Safety Recall Information: NHTSA Campaign ID: 16V-290 Manufacturer Recall Number: S33 Component: Airbag / Clock Spring This recall was previously performed by a dealership in February 2021; however, the vehicle is now experiencing the same symptoms the recall was intended to address, indicating the safety defect has reoccurred or was not permanently remedied. The vehicle is currently experiencing: Illuminated airbag (SRS) warning light Horn failure Traction control / electronic stability program warning light Erratic or abnormal A/C behavior that coincides with the SRS/steering wheel electrical faults These failures are consistent with a defective clock spring and directly impact the Supplemental Restraint System and other active safety systems. I contacted an authorized Jeep dealership to request inspection and repair of this recurring safety defect. The dealership confirmed the recall had been previously completed but refused to diagnose or repair the vehicle, stating in writing: “Due to company policy, we are unable to perform diagnostic or repair services on vehicles that are more than 10 years old.” They further stated that because the recall was marked as completed in 2021, they would not assist further and recommended I seek an independent repair facility. I believe this refusal violates the intent and requirements of the National Traffic and Motor Vehicle Safety Act (49 U.S.C. §§ 30118–30120), which requires manufacturers to remedy safety defects and does not allow age-based or policy-based refusal when a safety defect exists or reoccurs. This defect involves the airbag system and active safety features and presents an ongoing risk to vehicle occupants. I am requesting NHTSA’s assistance in reviewing this matter and ensuring that the manufacturer and/or authorized dealer fulfills their obligation to properly remedy this safety defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 5
- Unknown or other
The Bushing which attaches my shifter to the shifting cable keeps coming off/ breaking. 4 times in about 6-8 weeks. The first 3 times D N C auto repair in Ash Grove, Mo fixed for me. Today im having my Jeep towed to Corwin Dodge Jeep.
- Service brakes
ABS MODULE fault Abs Traction control inoperable, no parts available, no fixes available.
- Seat belts
Seatbelt will not unlatch
- Electrical system · Forward collision avoidance › Automatic emergency braking
TIPM failure. Recall 07V291000 My vehicle (2007 Jeep Wrangler) is not included in the recall, although it was recalled for this model. Car suddenly had a variety of bizarre electrical malfunctions including wipers acting on their own, difficulty starting, and stalling while driving. Mechanic inspection ($150) Also contirmed that it is the TIPM. The vehicle is too dangerous to drive before the TIPM is replaced.
- Electrical system · Engine · Fuel/propulsion system
In 2022, I paid over $15,000 to an official Jeep dealership (Chrysler Dodge Jeep RAM City, Greenwich CT) to replace the engine in my Jeep Wrangler. Without clear disclosure or consent, they installed a non-OEM Jasper remanufactured engine. The invoice misleadingly stated “ALL PARTS ARE NEW UNLESS…
In 2022, I paid over $15,000 to an official Jeep dealership (Chrysler Dodge Jeep RAM City, Greenwich CT) to replace the engine in my Jeep Wrangler. Without clear disclosure or consent, they installed a non-OEM Jasper remanufactured engine. The invoice misleadingly stated “ALL PARTS ARE NEW UNLESS OTHERWISE INDICATED,” with no mention of Jasper or warranty terms. The vehicle began malfunctioning almost immediately, raising multiple serious safety concerns, confirmed by written service exchanges: •“The Jeep is stopping alone! Just crazy, brakes come on alone” — 🛑 Spontaneous brake engagement poses a serious crash risk. •“It also smells strong gas when turning the car on” — 🚨 Potential fuel leak or misfire, which is a fire hazard. •“The Jeep is malfunctioning,” “check engine light came back on,” “needs a PCM”, followed by: “I’m not sure this is a computer problem, but the motor you folks placed in the car.” — ⚠️ Suggests deeper integration issues between the engine and vehicle electronics. After only ~8,000 miles, the engine failed again. I spent thousands more with an independent mechanic, who found that several parts supposedly replaced in 2022 were already failing again (spark plugs, oil cooler, manifold gaskets, thermostat). This points to reused components, poor-quality parts, or improper installation. Stellantis refuses to assist, claiming their dealership is “independent,” despite operating under Stellantis branding and authorization. A Stellantis rep confirmed they would only file an internal complaint and left me to handle everything alone. This reflects mechanical negligence, brand-level accountability failures, and clear safety threats. I’m requesting NHTSA investigate: •Post-engine replacement safety hazards and quality of work and materials •Dangerous servicing practices at this authorized dealership (if not many or all of them) •Stellantis’ lack of oversight over branded repairs
- Service brakes, hydraulic
The contact owns a 2007 Jeep Wrangler. The contact stated that while driving into a parking area, the contact heard a loud bang, prompting the contact to attempt to stop the vehicle. The contact stated that the brake pedal needed to be pumped several times before the vehicle came to a stop. After a…
The contact owns a 2007 Jeep Wrangler. The contact stated that while driving into a parking area, the contact heard a loud bang, prompting the contact to attempt to stop the vehicle. The contact stated that the brake pedal needed to be pumped several times before the vehicle came to a stop. After a visual inspection, the contact observed that the rear passenger side tire was punctured, and the brake caliper and rotor had detached. The contact believed that the failure of the caliper had punctured the tire. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 86,000.
- Air bags
I have 5 recalls but have been told by the dealer that because my vehicle is a re-constructed title that recalls cannot be done. Is this true?
- Service brakes · Steering · Suspension
when i drive the vehicle, i goes into this shaky mode where i have to completely stop the car and restart it. this happens if i hit any kind of bump. I brake every bump that i see hoping it will stop but today is got so bad i could not move. Also the braking for driving down a curvy mountain. I almost got in multiple accidents this week
- Electrical system › Starter assembly
The contact owns a 2007 Jeep Wrangler. The contact stated that while attempting to start the vehicle, the vehicle briefly failed to start before returning to normal functionality. After starting the vehicle, the vehicle returned to normal functionality, but the failure became a regular occurrence.…
The contact owns a 2007 Jeep Wrangler. The contact stated that while attempting to start the vehicle, the vehicle briefly failed to start before returning to normal functionality. After starting the vehicle, the vehicle returned to normal functionality, but the failure became a regular occurrence. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 80,000.
- Air bags
Delearship claims they repaired three recalls on vehicle... but they did not!!
- Air bags
There was not an incident, thankfully. However, I was billed for recalls to be complete, but they were not actually completed. I have attached the receipt showing where the service department claimed they completed the recalls but Jeep Corporate states the recalls have NOT been completed and are still open recalls. This service department has been dishonest about several other issues as well.
- Air bags
I called the dealership to see what do I need to do for my recall they told me to bring my car in. I brought my car in and they said that I need a appointment to bring it back on 7/25/2023. I brought it back on 7/25/23 and they kept it until 7/28/23 told be that they need to order parts. They have…
I called the dealership to see what do I need to do for my recall they told me to bring my car in. I brought my car in and they said that I need a appointment to bring it back on 7/25/2023. I brought it back on 7/25/23 and they kept it until 7/28/23 told be that they need to order parts. They have not contacted me. I would like to file a complaint All Star Dodge in Denham Springs, Louisiana 225-523-3652. Please let me know what I need to do. I have had 2 people come to my house about this recall and the dealership has been no help! Michelle Smith 225-931-5276
- Electrical system · Exterior lighting · Visibility/wiper
Premature failure of TIPM, multifunction headlight switch and multifunction switch.causing no wipers or turn signals engine shuts down randomly. Faulty rollover valve in gas tank that leaks fumes and gas spits from fuel fill when full
- Electrical system · Exterior lighting · Visibility/wiper
The door locks will unlock and lock by themselves. Without anything being touched. It does it so often that it will run the battery dead at night as the headlights come on every time the vehicle unlock is triggered. Also the horn will sound for no reason. Unprovoked at all hours. No warning whatsoever.
- Fuel/propulsion system
Service Bulletin # 14-001-11, dated February 11, 2011 built between March 1, 2007 March 31, 2008 recall on inlet check valve recall. My vehicle was built 08/2006 and does not fall within the dated window however it is experiencing the issue. Gas overflow is not only a cost of money but also a danger to the environment. I am asking for an extension on this recall to include my manufactured year.
- Power train
The contact owns a 2007 Jeep Wrangler. The contact stated that while driving at various speeds, the vehicle would independently enter limp mode with the check engine warning light illuminated. The contact had taken the vehicle to the dealer where they replaced the valve body. Recently, the contact…
The contact owns a 2007 Jeep Wrangler. The contact stated that while driving at various speeds, the vehicle would independently enter limp mode with the check engine warning light illuminated. The contact had taken the vehicle to the dealer where they replaced the valve body. Recently, the contact stated upon placing the gear shifter into the Reverse, the vehicle would fail to move backward. The check engine light then illuminated. The contact took the vehicle to the dealer where he was given an estimate for a new transmission. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 156,000.
- Fuel/propulsion system
Fuel spits out during filling so you have to barely squeeze the pump handle. It takes a long time to just put 20.00 in gas in it sometimes as long as 5 mins. When you live in a cold weather state it becomes an issue when you try to pump it and get splashed with gas because you are trying to get out of the cold. Seems like this would be a health hazard along with a fueling problem.
- Fuel system, gasoline › Storage › Tank assembly › Filler pipe and cap
The contact's girlfriend owns a 2007 Jeep Wrangler. The contact stated while refueling the vehicle, gasoline would spew out of the fuel filler neck. The dealer was made aware of the failure but informed the contact that there was no recall associated with the VIN and that the vehicle was out of…
The contact's girlfriend owns a 2007 Jeep Wrangler. The contact stated while refueling the vehicle, gasoline would spew out of the fuel filler neck. The dealer was made aware of the failure but informed the contact that there was no recall associated with the VIN and that the vehicle was out of warranty. The manufacturer was made aware of the failure but informed the contact that the vehicle was out of warranty. The vehicle was not repaired. The failure mileage was approximately 130,000.
- Steering · Suspension · Wheels
Vehicle engine light came on after driving from carlot- after 50 miles. Meineke- diagnosed report stated, -O2 sensors & catalytic converter needed replacement. Two of tires had a patched over hole. The other two tires had inner bar wears &vehicle needed a steering box.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Air Bag Clockspring Wiring Failure
On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This…
On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.
- Air Bag Clockspring Wiring Failure
In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light…
In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light was allegedly on or came on afterward the crash, one of which also alleged injuries as a result of the non-deployment.FCA also provided data on other make, model and model year vehicles using the same clockspring.Additionally FCA provided 16,955 warranty claims related to the replacement of the air bag clockspring wiring assembly.It should be noted that FCA initiated an Extended Warranty Program on the left hand drive MY 2007 Wrangler in late calendar year 2011.6,777 of these claims are from the MY 2007 left hand drive Wrangler.FCA advises that some of the warranty claims involved clockspring failures that would not affect the air bag operation, for example due to noise, cruise control and/or radio operation issues.Many of these claims involved newer model year subject vehicles.FCA also noted that Wrangler's removable roof and door configuration may make it more susceptible to outdoor water/moisture and dust ingress.ODI investigated the right hand drive Wrangler in calender year 2011 for a similar clockspring issue under PE11-019.That investigation lead to NHTSA Safety Recall 11V258 on right hand drive model year (MY) 2008-2012 Wranglers.FCA redesigned the remedy clockspring to improve its durability and environmental protection and revised the design of the steering wheel to column shroud.Base on the data reviewed, this Preliminary Analysis (PE) is being upgraded to an Engineering Analysis (EA).The reports cited above are listed in the public investigative file available at SaferCar.gov under this investigation ID.
- Totally Integrated Power Module Failure
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007…
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
- Airbag Clockspring Failure
In its July 29, 2011 response to ODI's May 27, 2011 information request letter, Chrysler provided 153 MY 2007-2008 owner reports, additional to the 28 ODI Vehicle Owner Questionnaires (VOQs), which related to the illumination of the air bag light (ABL) due to a faulty clockspring (CS) wiring circuit.The right hand…
In its July 29, 2011 response to ODI's May 27, 2011 information request letter, Chrysler provided 153 MY 2007-2008 owner reports, additional to the 28 ODI Vehicle Owner Questionnaires (VOQs), which related to the illumination of the air bag light (ABL) due to a faulty clockspring (CS) wiring circuit.The right hand drive (RHD) vehicles, which were first produced in MY 2008 and account for only 1% of vehicle production, accounted for 82 of these 181 reports (45%).The MY2007 left hand drive (LHD) vehicle accounted for 61 of the remaining 92 LHD reports and exhibited a higher complaint rate than the MY 2008 LHD vehicles.ODI did not identify any incidents of crashes/injuries attributable to the CS circuit failure.Since May 27, 2011, ODI has received another 32 consumer complaints bringing the total to 213 reports at this closing.In addition, and for comparative purposes, Chrysler provided another 42 owner reports it received on the MY2006 and MY2009-2010 Wrangler vehicles; these populations showed a lower incident rate than the subject vehicles, especially in comparison to the RHD subject vehicles. Chrysler's investigation showed that the higher rate of RHD Wrangler CS failures were due to a more severe duty cycle for these vehicles which are primarily used by US Postal workers/mail carriers delivering mail in rural regions.Chrysler concluded the unique vehicle usage, much of which occurs with the driver's window open and under dusty environmental conditions, is the cause of premature CS failure.Chrysler's analysis also indicated that the somewhat elevated MY2007 LHD rate, which showed a declining failure trend, was the result of start-up production/assembly issues that occurred with the introduction of a new design CS.The new design CS incorporated both dual airbag inflator circuitry and a steering wheel angle sensor (for the electronic stability control system).On November 1, 2011, Chrysler submitted a defect notice indicating it will conduct a recall of all MY 2008-2012 RHD Wrangler vehicles (11V528).The estimated 5,334 RHD Wrangler vehicles include the 2,297 MY 2008 RHD Wrangler vehicles, which were the subject of this investigation, plus an additional 3,037 MY 2009-2012 RHD Wrangler vehicles that Chrysler determined potentially have a similar CS concern as the MY 2008 RHD vehicles.Chrysler intends to replace the existing CS with a yet-to-be-produced improved CS assembly, or an improved steering housing assembly that is less susceptible to dusty environments.Owner notice is scheduled to begin in November, 2011.Chrysler also informed ODI that it intends to initiate a consumer satisfaction campaign for MY2007 LHD Wrangler which will extend the CS warranty coverage for 10 years or 150,000 miles.Accordingly the investigation is closed.
- Fleet Vehicle Recall Completion Audit
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary…
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
- Fuel Spill During Refueling
ODI found the rate of warranty claims related to fuel spit back on the subject vehicles is lower than other vehicles previously recalled to correct defects related to fuel spit back.Although the rate of complaints reported to the agency on the subject vehicles is higher than or similar to the rates experienced in…
ODI found the rate of warranty claims related to fuel spit back on the subject vehicles is lower than other vehicles previously recalled to correct defects related to fuel spit back.Although the rate of complaints reported to the agency on the subject vehicles is higher than or similar to the rates experienced in previous investigations where safety recalls were conducted, ODI suspects that the NHTSA safety complaints submitted by subject vehicles owners may have been influenced by internet related publicity both before and during this investigation.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.See attached report for additional information.In addition, Chrysler is initiating a lifetime warranty program, at no cost to the consumer, to address the fuel spit back problem in approximately 135,000 model year 2007-2008 Jeep Wrangler vehicles built from March 1, 2007 to March 31, 2008.Chrysler will notify all affected vehicle owners of this action.Consumers should refer to the warranty and service bulletins and sample owner notification letter available in the investigative file.The vehicle build date can be found on the certification label located on the driver door or door jamb.
- Transmission overheating / fire
In a letter dated november 3, 2009, chrysler group llc (chrysler), notified nhtsa that it will conduct a safety recall of approximately 161,000 model year (my) 2007 and 2008 jeep wrangler vehicles built with automatic transmissions.chrysler stated that these vehicles were not equipped with a transmission fluid…
In a letter dated november 3, 2009, chrysler group llc (chrysler), notified nhtsa that it will conduct a safety recall of approximately 161,000 model year (my) 2007 and 2008 jeep wrangler vehicles built with automatic transmissions.chrysler stated that these vehicles were not equipped with a transmission fluid temperature warning system and the operation of these vehicles beyond the limits of reasonable usage over a period of time could result in transmission failure and in some cases transmission fluid expulsion.the expelled fluid could come in contact with a hot engine or exhaust component and cause a fire.chrysler will conduct a safety recall to install a hot oil warning message in the instrument cluster and a chime indicating an elevated transmission fluid temperature condition.an owner's manual addendum stating the purpose of the hot oil message and chime to include caution and warning statements regarding elevated transmission fluid temperature conditions will be provided to owners.based on chrysler's decision to conduct a safety recall this engineering analysis IS closed.
- Tow bar assembly failure
The defective tow bar assemblies involved in this recall were supplied to chrysler for use on some of its jeep wrangler vehicles.the purpose of this investigation was to identify any additional purchasers of identical or substantially similar defective assemblies and to initiate additional defect reporting and safety…
The defective tow bar assemblies involved in this recall were supplied to chrysler for use on some of its jeep wrangler vehicles.the purpose of this investigation was to identify any additional purchasers of identical or substantially similar defective assemblies and to initiate additional defect reporting and safety recalls as necessary.to accomplish this rmd contacted the supplier of the assemblies, valley towing products, and confirmed no other such assemblies were distributed.this eq IS therefore closed.
- Engine stalling & electric power loss
On july 3, 2007, daimlerchrysler corporation (dcc) submitted a defect information report to nhtsa describing a defect that could result in engine stall while driving in approximately 80,894 model year (my) 2007 jeep wrangler and dodge nitro vehicles manufactured between january 30, 2006 and january 22, 2007 (nhtsa…
On july 3, 2007, daimlerchrysler corporation (dcc) submitted a defect information report to nhtsa describing a defect that could result in engine stall while driving in approximately 80,894 model year (my) 2007 jeep wrangler and dodge nitro vehicles manufactured between january 30, 2006 and january 22, 2007 (nhtsa recall 07v-291, dcc recall g25).according to dcc, the totally integrated power module (tipm) in these vehicles was programmed with software that may allow the engine to stall under certain conditions.dcc will reprogram the tipm in the recalled vehicles with revised software. Odi opened pe07-027 on may 29, 2007, based on 53 complaints alleging engine stall and/or loss of electrical power in my 2007 jeep wrangler vehicles.odi was also monitoring similar complaints in my 2007 dodge nitro vehicles.dcc's analysis of complaints to dcc and nhtsa found that many described events with a momentary loss of electrical power inside the vehicle and a corresponding loss of engine power.many of the reports also indicated that the instrument cluster telltale lamps momentarily illuminated during the event. Dcc's engineering analysis determined that the tipm could initiate an internal reset cycle lasting approximately 75 ms in response to error messages on the communication bus.the key on signal from the tipm to the powertrain control module (pcm) IS lost during a tipm reset.if the pcm loses the key on signal for longer than 40 ms, it interprets it as the vehicle ignition being turned off and begins a power down routine.after the tipm reset, the key on signal IS restored and the pcm powers back up.if the rotating components of the engine contain sufficient inertia, the vehicle may restart with no input from the operator as reported in some of the complaints.if the engine does not restart in this manner, it can be restarted by the operator.a revision to the tipm software on january 22, 2007 changed the tipm reset time to 17 ms, removing the potential for pcm power down and engine stall. Odi has received 178 complaints potentially related to the alleged defect in my 2007 jeep wrangler vehicles and 52 complaints involving my 2007 dodge nitro vehicles.two of the nitro complaints allege that a crash resulted from an engine stall incident, one of which caused minor injuries to a passenger.as of june 1, 2007, dcc identified 151 wrangler complaints and 128 nitro complaints. This investigation has been closed with dcc's recall.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010205Plate - Planetary
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10232025Cowl Trim Panel Fastener Water Leak
- 10229998KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
- 10229986Cowl Trim Panel Fastener Water Leak
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223602Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223599Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- 10223525Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set
- 10223386KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
- 10223226KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
- 10221831(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
- 10221069Cowl Trim Panel Fastener Water Leak This bulletin involves modifying or replacing the cowl trim panel fasteners to correct a water leak condition. The customer may describe a water accumulation condition on the vehicle floor front foot well area.
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10219885Front Brake Caliper Hose Leak (X71 Warranty Extension) This bulletin involves replacing both front brake caliper hoses and wheel speed sensors. Customers may experience a brake fluid leak coming from the front wheel opening area. This issue is due to corrosion at the crimps on the brake caliper hosesFig.1.If the customer describes the symptom/condition listed above, perform the Repair Procedure.Example Of Corrosion At Crimps
- 10219850(X71) Front Left and Right Brake Caliper Hoses & Both Wheel Speed Sensors - 2007 - 2010 Jeep Wranglers (JK)
- 10219849Customer Satisfaction Notification S80 Aftermarket Dana 60 Front Axle The aftermarket front axle steering knuckles have been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.
- 10218192Cowl Trim Panel Fastener Water Leak This bulletin involves modifying or replacing the cowl trim panel fasteners to correct a water leak condition. The customer may describe a water accumulation condition on the vehicle floor front foot well area.
- 10218062This bulletin involves replacing the Airbag Clockspring if the Airbag Warning Lamp Is
- 10217693Soft Top Door Rail Service Kits Use this soft top door frame rail kit for worn foam or a water leak: 1) For 2010 - 2014 units, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply new foam part.~ 2) For 2007 - 2009 units, cut off 8.0 mm from the end that faces the windshield, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply modified foam part.
- 10217425Cracked Vinyl Soft Top Window This bulletin provides soft top vinyl window precautions during cold weather.
- 10216395Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
- 10216187Cracked Vinyl Soft Top Window This bulletin provides soft top vinyl window precautions during cold weather.
- 10215997Replacing Door, Hood And/Or Tailgate Hinges This bulletin involves replacing, refinishing and sealing door, tailgate and hood hinges.
- 10215916Warranty Bulletin D-18-16 Rev. B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)
- 10215096This bulletin involves replacing the Airbag Clockspring if the Airbag Warning Lamp Is
- 10198300KEY, BLANK WITH TRANSMITTER Please note that after programming the new key integrated transmitter that Lock, Unlock and Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.
- 10191460Valve Body. These may cause over drive cycling.
- 10189389Fuel Spit Back During Refueling (X47 Lifetime Warranty Extension) This bulletin involves replacing the fuel tube at the fuel tank. This new fuel tube has a check valve. Some customers may experience a fuel spit back condition during a refueling event.
- 10189371Soft Top Rear Window Zipper Will Not Disengage This bulletin involves removing the metal zipper stops from the end of the rear window zipper in order to adjust and realign the zipper tapes to eliminate zipper skips that can prevent the zipper from disengagement. .1 - Zipper Tapes Aligned Correctly2 - Metal Seperator Pins3 - Misaligned Zipper Tapes4 - Zipper Sliders
- 10188692Replacing Door, Hood And/Or Tailgate Hinges This bulletin involves replacing, refinishing and sealing door, tailgate and hood hinges.
- 10187095Warranty Bulletin D-18-16 Rev. B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)
- 10180221(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10175510DIPAP Requirements - Addition of Jeep Wrangler (JL/JK) and Jeep Gladiator (JT) Hard Top and Targa Top Panel Replacements - All Dealers (Rev. A)
Every Jeep Wrangler model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.